THORN 55 ULTIMATE SECURITY FOR YOUR CAR OWNER’S MANUAL This device complies with pant 135 of F.C.C rules. Operation of this decide is subject to the following two conditions. 1. This device my not cause harmful interference. 2. This device must accept any interference that may cause undesired operation NOTE equipment. Such modifications could void the user's authority to operate the equipment.
SELF CODE LEARNING SYSTEM Tom is equipped with a computerized security code system. This unique feature memorizes the code number for your system and expands with another remote transmitter very easily. SELF CODE LEARNING: Thorn will learn the code in valet mode as follow CODE LEARNING IN VALET MODE: . Turn ignition key to “on” position. . Press the valet switch “on” for 2 seconds then LED. “on”. @ No . Turn ignition key to offfonfofffonfoff within 10 seconds then L.E.D. flashing, & .
ARM AND DISARM THORN THORN MAY BE ARMED IN 3 DIFFERENT WAYS. 1. Remote Control with Chirp: Press button 1 of the remote control to arm, 1 chirp & I light flash, 2. Remote Control with no Chirp: Briefly press button 2 of the remote control before pressing button 1 to arm silently, no chirp & 1 light flash. 3. Automatic passive arming: 3 seconds after the last door is closed, Thorn will chirp once as a preliminary signal. Then after 30 seconds, Thorn will arm, 1 chirp & 1 light flash.
PANIC MODE FOR YOUR PERSONAL SAFETY Thorn may be triggered by the remote control. Press button | until Tom's siren blasts for about 3 seconds, then release the button. When panic made is activated, Thorn will sound for a complete 60 seconds cycle. Pressing button 1 once more will deactivate panic mode. For your personal safety, panic mode will be activated even when Thorn is in valet mode. VALET MODE Valet mode is designed to prevent Thorn from arming or triggering when the protection is not needed.
L.E.D. STATUS LIGHT ‘Thor's armed status in reported by the flashing L.E.D. light located inside the vehicle. This light is off when Tom is disarmed and is on constant red when Thorn is in valet mode. L.E.D. INDICATOR I __ Flashing Red Armed [om “Disarmed — On Constant Red . Valet Mode r Rapid Red Flash | Passive Arming Countdown SHOCK DELETE VIA REMOTE CONTROL Press the remote control button #2 within 3 seconds after the Tom system is armed by transmitter then Thorn will chirp once.
OPTIONAL FEATURES REMOTE LOCK AND UNLOCK Thorn may be interfaced with your vehicles power lock. This feature will lock the doors of your vehicle when Thorn is armed. It will also unlock the doors when Tom is disarmed. NOTE: Some vehicles may require additional components. The remote lock and unlock feature will operate even in valet mode, always providing key less convenience.
THORN LIMITED LIFE TIME WARRANTY Alarm 1. Div. of OFT Inc., guarantees to the original purchaser of the Thorn auto security system to repair or replace any electronic control module, If the said parts are found defective in workmanship or material under normal use during the lifetime of the automobile in which the alarm system is originally installed. It needs to be proved that the alarm system was installed property and serviced by an authorized agent.
1. RED/WHITE {RELAY REQUIRED) The red/white wire is the alarm’s negative channel 2 output. This momentary output switches to ground when the no, 2 button of the remote control is pressed. It may be used with a relay for remote trunk release, or may be used to trigger another optional feature. 2. YELLOW Connect the yellow wire coming out of the starter kill socket to the true ignition. This is ignition power that stays on when in start mode. Use a volt meter to locate proper wire.
L.E.D. INDICATOR Mount the LED. indicator in visible location, such as dash or console. The lens may be unsnapped for easy installation. Connect as follow; RED wire: Connect to pink wire of control module BLACK wire: Connect to chassis ground SHOCK SENSOR Firmly mount the shock sensor under the dash and connect as follow. BLUE wire : Connect to blue wire of control module RED wire: Connect to fused volt power BLACK wire: Connect to chassis ground 1.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two condition: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID : HH8-DYTH2240-TX Caution: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.