TDS

CONTACT INFORMATION: Black Diamond Coatings, Inc. 6036 Nature Coast Blvd. Brooksville, FL 34602. USA.
www.BDCbrands.com | 800-270-4050 | [e-mail] Page 1 of 2
© 2022 Black Diamond Coatings, Inc.
TECHNICAL DATA SHEET:
September 2015
SG+
TM
The PRO TECH SERIES DOMINATOR® SG+ PRO TECH SERIES is designed
for use by professional contractors and DIYers who demand excellent
products with high performance. DOMINATOR® SG+ is a color-
enhancing, film forming and joint stabilizing sealer that provides a
satin to high-gloss finish on concrete pavers and decorative
concrete surfaces.
FEATURES AND BENEFITS
PHYSICAL DATA
Product Type:
¨ Water-based Acrylic Urethane-modified
Finish:
¨ High-gloss to satin finish
¨ Color-enhancing sealer
Components:
¨ One
Curing
Mechanism:
¨ Air dry
Coverage:
¨ 250 – 400 sq. ft. per gallon per coat,
depending on the surface porosity and
application method
VOCs:
¨ <100g/l
Solids Content:
¨ 33% +/- 2%
Flashpoint
¨ 100 °C / 212 °F
Shelf Life:
¨ Best used within 12 months of manufacture
Use this product on the following surfaces:
Surface
DOMINATOR® SG+
Bare Concrete
✔*
Decorative Concrete
✔
Concrete Brick Pavers
✔
* DOMINATOR® SG+ on bare concrete will highlight imperfections and
porosity variations in the concrete.
Refer to the Safety Data Sheet for more technical detail.
TESTING DATA
APPLICATION PROCESS
1. PREPARE
Clean the surfaces thoroughly. The surface to be sealed should be
properly cleaned before the sealer is applied. The surface should be free
of dirt, oil, contaminants, and any other substance that could interfere
with the sealer penetrating the pavers as intended. For best results,
pressure wash with a minimum of 2000 psi pressure washer, or manually
scrub substrate with the OBSESS™ Outdoor Cleaner to remove
contaminates. Rinse and repeat until the surface area is clear of any
cleaner residue. If efflorescence is present, clean the entire surface
thoroughly with an efflorescence remover, prior to sealer application.
Ensure that the surface has not been recently sealed (within the last 12
months). If there is evidence of a previous sealer on the surface, remove
prior to application of the sealer. If this product is applied over previously
sealed surfaces with another sealer brand, adherence issues may occur.
If there is no visual evidence of another sealer, test for water beading. If
water beads, use the appropriate stripper to remove old sealer from the
surface. Failure to comply with this instruction can result in adherence
issues. Protect surfaces not intended to be sealed. Cleaning can be
performed the day before or the same day as the sealing. It is acceptable
to seal the damp surface if there is no standing water; however, to obtain
optimal performance, a drier surface is better.
Protect surfaces not intended to be sealed. Ensure that walls and other
surfaces are protected, and divert pedestrian and auto traffic, as needed.
Ensure proper surface temperature. The surface temperature should be
between 50-115° F (10-46° C) and should not drop below the minimum
temperature for 48 hours from the start of application.
Use the proper equipment. We recommend a pump-up or battery-
operated back-pack sprayer with the appropriate spray pattern for your
project. Be sure to back roll any product that may puddle during the
spray application. Alternatively, a 3/8" to 3/4" nap roller can be used,
being careful to lightly apply the product.
Professional
results
¨ Fast Dry
¨ Moisture Resistant
¨ Stain, Scratch and Rub resistant
¨ Joint stabilizing
¨ UV resistant for longer life
Easy application
¨ One-part for no waste in application
¨ Can use on damp surfaces
¨ Can be applied to vertical surfaces
Breathable
¨ Allows efflorescence and moisture to
escape
Eco-friendly
¨ Low VOCs to exceed all federal, state and
local standards
Chemical Resistance: ASTM
D1308
No change after 24 hours of exposure
to motor oil, antifreeze, Transmission
fluid, Grape Juice, Bleach, 10% Muriatic
Acid, Isopropyl Alcohol, Red Wine.
Slip Resistance: Australian
Pendulum Test Method HB
198
Classified as “low slip potential” when
wet or dry by (CTIOA), and addition of
DIAMOND GRIT
TM
improves traction.
Outdoor Durability: ASTM
G154
Slight color change at 2100 hours,
water continues to bead; retained 46%
of original shine
Initial Gloss 60°/20° on
Sealed Surface
121/93
Hardness @ 18 Days
Koenig Pendulum Hardness
42