TDS

CONTACT INFORMATION: Black Diamond Coatings, Inc. 6036 Nature Coast Blvd. Brooksville, FL 34602. USA.
www.BDCbrands.com | 800-270-4050 | [e-mail] Page 1 of 2
© 2022 Black Diamond Coatings, Inc.
The PRO TECH SERIES DOMINATOR
®
LG+ sealer is designed for use by
professional contractors and DIYers who demand excellent products
with high performance. DOMINATOR® LG+ is a color-enhancing, film
forming and joint stabilizing sealer that provides a semi-gloss to low
gloss finish on concrete pavers and other concrete surfaces.
FEATURES AND BENEFITS
Professional
results
¨ Fast Dry
¨ Moisture Resistant
¨ Stain, Scratch and Rub resistant
¨ Joint stabilizing
¨ UV resistant for longer life
Easy application
¨ One-part for no waste in application
¨ Can use on damp pavers
¨ Can be applied to vertical surfaces
Breathable
¨ Allows efflorescence and moisture to
escape from pavers
Eco-friendly
¨ Low VOCs to exceed all federal, state
and local standards
PHYSICAL DATA
Product Type:
¨ Water-based Acrylic Urethane-modified
Finish:
¨ Semi-gloss to low gloss finish
¨ Color-enhancing sealer
Components:
¨ One
Curing
Mechanism:
¨ Air dry
Coverage:
¨ 250 – 400 sq. ft. per gallon per coat,
depending on the surface porosity and
application method
VOCs:
¨ <100g/l
Flashpoint:
¨ 100 °C / 212 °F
Solids Content:
¨ 25% +/- 2%
Shelf Life:
¨ Best used within 12 months of
manufacture
Use this product on the following surfaces:
Surface
DOMINATOR® LG+
Bare Concrete
✔*
Decorative Concrete
✔
Concrete Brick Pavers
✔
*DOMINATOR® LG+ on bare concrete will highlight imperfections and
porosity variations in the concrete.
Refer to the Safety Data Sheet for more technical detail.
TESTING DATA
Chemical Resistance: ASTM
D1308
No change after 24 hours of
exposure to motor oil, antifreeze,
Transmission fluid, Grape Juice,
Bleach, 10% Muriatic Acid, Isopropyl
Alcohol, Red Wine.
Slip Resistance: Australian
Pendulum Test Method HB
198
Classified as “low slip potential”
when wet or dry by (CTIOA), and
addition of DIAMOND GRIT
TM
improves traction.
Outdoor Durability: ASTM
G154
Slight color change at 2100 hours,
water continues to bead; retained
46% of original color
APPLICATION PROCESS
1. PREPARE
Clean the surfaces thoroughly. The surface to be sealed should be
properly cleaned before the sealer is applied. The surface should be free
of dirt, oil, contaminants, and any other substance that could interfere
with the sealer penetrating the pavers as intended. For best results,
pressure wash with a minimum of 2000 psi pressure washer, or manually
scrub substrate with the OBSESS™ Outdoor Cleaner to remove
contaminates. Rinse and repeat until the surface area is clear of any
cleaner residue. If efflorescence is present, clean the entire surface
thoroughly with an efflorescence remover, prior to sealer application.
Ensure that the surface has not been recently sealed. If there is evidence
of a previous sealer on the surface, remove prior to application of the
sealer. If this product is applied over previously sealed surfaces with
another sealer brand, adherence issues may occur. If there is no visual
evidence of another sealer, test for water beading. If water beads, use the
appropriate stripper to remove old sealer from the surface. Failure to
comply with this instruction can result in adherence issues. Protect
surfaces not intended to be sealed. Cleaning can be performed the day
before or the same day as the sealing. It is acceptable to seal the damp
surface if there is no standing water; however, to obtain optimal
performance, a drier surface is better.
Protect surfaces not intended to be sealed. Ensure that walls and other
surfaces are protected, and divert pedestrian and auto traffic, as needed.
Ensure proper surface temperature. The surface temperature should be
between 50-115° F (10-46° C) and should not drop below the minimum
temperature for 48 hours from the start of application.
Use the proper equipment. We recommend a pump-up or battery-
operated back-pack sprayer with the appropriate spray pattern for your
project. Be sure to back roll any product that may puddle during the
spray application. Alternatively, a 3/8" to 3/4" nap roller can be used,
being careful to lightly apply the product.
MASONRY/CONCRETE APPLICATION