2.0 CU. FT. 15LBS FRONT LOAD WASHER/DRYER INSTALLATION & USERS MANUAL MODEL WDCVLW Form No. 3020307A2542 Released 4/14 USA SERVICE OFFICE Dometic Corporation 2320 Industrial Parkway Elkhart, IN 46516 CANADA Dometic Corporation 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA For Service Center Or Dealer Locations Please Visit: www.eDometic.
Contents SAFETY PRECAUTIONS Important Safety Instructions Grounding Instructions Before Operating this Appliance Appliance Handling Cautions Before Moving the Appliance Cautions when Washing Clothes INSTALLATION REQUIREMENTS Tools and parts Location requirements Installation Clearances Electrical Requirements Appliance Dimensions Unpacking Appliance Disposal of Packing Materials INSTALLATION INSTRUCTIONS Removal of Transportation Bolts Location Selection Connect Inlet Pipe Connect Inlet Hoses Drain System O
TECHNICAL SPECIFICATIONS SAFETY PRECAUTIONS IMPORTANT SAFETY INSTRUCTIONS SPECIFICATIONS Power Supply 120V / 60Hz Dimension (W*D*H) 23.5”*21.5”*33.5” (597mm*546mm*838mm) Weight 165lbs (75kg) Washing/Dry Capacity 15.4lbs (7kg) Rated Current 12A Standard Water Pressure 7.3‐145 psi (0.05MPa—1MPa) Max.
SAFETY PRECAUTIONS DO NOT install or store this appliance where it will be exposed to the weather. APPENDIX Clothing Care Labels DO NOT tamper with controls. DO NOT repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.
ALARM CODES SAFETY PRECAUTIONS Grounding Instructions Alarm Code Description E30 Door lock problem. Reason Solution Door not properly closed. Restart after the door is closed. This appliance must be grounded. In the event of a malfunction or breakdown Electrical short, grounding will reduce the risk of electric shock by providing a path of least resistance for the electric current. This appliance is equipped with a cord that has an equipment-grounding conductor and a grounding plug.
SAFETY PRECAUTIONS TROUBLESHOOTING TIPS DO NOT wash carpets. BURN HAZZARD! Be careful of scalding when washing machine drains hot wash water. Troubles After the program is completed, open the door after the bell. Always follow the fabric care instructions recommended by the clothing manufacturer. Solution Washing machine does not start up. Check if the door is closed tightly. Check if the power plug is inserted properly. Check if water supply tap is open.
CARE AND CLEANING INSTALLATION REQUIREMENTS Proceed as follows: 1. Turn knob clockwise 2. Open the filter's door This machine must be grounded properly. If there is any short circuit, grounding can reduce the danger of electrical shock. This appliance MUST be connected to a dedicated 15 Amp circuit separate from other electrical appliances and MUST have overcurrent protection device rated at 15Amps. Otherwise, power protector may be tripped or fuse may be burned out.
INSTALLATION REQUIREMENTS CARE AND CLEANING Location Requirements Selecting the proper location for your washer improves performance and minimizes noise and possible washer vibration and possible movement. In selecting your washer/dryer location consideration must be taken for the drain system, see “Drain System Options ” on page 11,. Requirements: 1. A water heater set to deliver 120°F (49°C) water to the washer. 2. A grounded electrical outlet located within 6 ft.(1.
CARE AND CLEANING INSTALLATION REQUIREMENTS Before your maintenance starts, disconnect the power plug or disconnect power and shut the water valves off. Appliance Dimen- sions 41½” (105cm) 23½” (60cm) Solvents are forbidden to avoid damaging the washing machine and generating toxic gases which can explode. Never spray water on the washing machine to clean it. 33½” (85cm) It is forbidden that detergents containing PCMX are used to clean the washing machine.
INSTALLATION REQUIREMENTS OPERATING INSTRUCTIONS Removal of Transportation Bolts Table of Washing Procedures Before using this washing machine, transport bolts must be removed from the backside of this machine. Please take the following steps to remove the bolts: 1. Loosen the bolts with wrench and then remove them. 2. Cover the holes with transport hole plugs. 3. PROCEDURE Keep the transport bolts for future use. Location Selection Pre‐wash Temp.
OPERATING INSTRUCTIONS INSTALLATION REQUIREMENTS Selecting the Wash Cycle The minimum carry away capacity can be no less than 17 gal.(64 L) per minute. The top of the standpipe must be at least 23.6” (60cm) high and no higher than 39.4” (100cm) from the bottom of the washer. Warm II. III.
OPERATING INSTRUCTIONS INSTALLATION REQUIREMENTS b. 5. After positioning the washing machine, press four corners on top cover of washing machine in sequence. If the washing machine is not stable when being pressed, this leg must be adjusted. c. Ensure the positioning status of washing machine. Loosen the lock nut with wrench and turn the leg with hand until it closely contacts with the floor. d. Press the leg with one hand and fasten the nut tightly to the cabinet with wrench. e.
OPERATING INSTRUCTIONS Therefore, the displayed time may not be the actual run time. Bulky/Large: To increase the washing affects, washing time is increased. Except single quick, wash, drain and spin procedures, the other procedures can select Cotton intensive function. It is recommended to wash the clothes for babies or worn by persons with allergic skin. Bulky/large: The Bulky/Large wash cycle runs at approximately 1 hour and 30 minutes.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Clothes which easily get fuzzed should be turned inside-out for washing. Washing effectiveness depends on water hardness as well as the recommendations from the detergent manufacturers. Note: Keep detergents and additives in safe and dry places out of reach from children. Clothes are classified according to the following characteristics: DO NOT wash water-proof materials (ski suits, raincoats, etc.).
