R miniBar RH 131 RH 141 Type: MF20-60 Operating Instructions 207.5184.
Please read these operating instructions carefully before putting the refrigeration unit into operation. If you later sell or dispose of it, please ensure that the new owner receives these operating instructions. Please follow the installation details below carefully Guarantee is valid for products installed as described only. (See chapter 4.1) Thank you for choosing our appliance. We are sure it will provide you with trouble-free use.
C ONTENT S 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Unpacking View of the appliance Cleaning Positioning the appliance 4.1. Installation instruction Using the appliance 5.1. Temperature regulation 5.2. Cooling unit control (CUC) Ice cubes Useful suggestions Defrosting, cleaning and maintenance 8.1. Automatic defrost function Changing the lightbulb Reversing the door hang Replacing the decorative door panel Changing the feet Customer service Putting into operation, technical data 14.1.
1. Unpacking After removal from the cardboard packaging, make sure the appliance is not damaged. If you find damage to the appliance resulting from transport, report it immediately to the transportation firm. 2. View of the appliance RH 131 RH 141 Figure 1. 1. Door lock (if available) 6. Thermostat knob 2. Door 7. Fixing foot 3. Lamp (if available) 8. Evaporator sensor 4. Evaporator (behind evaporator) 5. Sensor IN CASE IF YOUR REFRIGERATOR IS EQUIPPED WITH LOCK, DOMETIC ZRT.
3. Cleaning Clean the refrigerator thoroughly at intervals, as necessary. Remove the shelves; these, the cabinet interior and the door should be washed with a warm solution of sodium bi-carbonate. Finally wipe over with a cloth rinsed in warm water only, and dry with a clean cloth. Do not wash any plastic parts in water that is more than hand warm, and do not expose them to dry heat. The outside of the cabinet should be wiped down regularly with a clean, damp cloth.
5. Using the appliance To start the refrigerator connect the plug into a properly earthed socket. The cooling fins should show signs of cooling after about 3 hours. The refrigerator needs about 6 hours at normal ambient temperature to reach 6 °C in the storage compartment. 5.1. Temperature regulation The usual setting required is in the region of 2 to 3 on the thermostat knob (Fig. 5), but this can vary with conditions of load and installation.
10. Reversing the door hang, (Fig. 7) Lay the appliance on its back. Remove the 8 screws (1). Remove the door, together with the two hinges (2), from the housing. Remove the two cover caps (3) from the housing and place them in the open hinge holes in the housing. Place the bottom righthand hinge in the top left of the door and the top righthand hinge in the bottom left of the door and hang the door on its hinges in the open cover cap holes in the housing. Secure the hinges and cover caps with the 8 screws.
13. Customer service Before you call a service engineer, carry out the following simple tests: Problem Possible cause The appliance does not Thermostat control is set too low. cool sufficiently. Too much food to be cooled was put in. Door is not shut properly. Refrigerator not level. Internal air circulation is restricted. External air circulation is restricted. The appliance does not CUC system stopped the cool at all. operation. Plug is not connected to the mains socket properly.
15. Environmental protection information The appliance does not contain any CFCs/HCFCs. Ammonia (natural hydrogen and nitrogen compound) is used as a refrigerating agent in the refrigeration unit. The ozone-friendly cyclopentane is activated as a motive agent for the PU foam insulation. Sodium chromate is used for corrosion protection (less than 2 weight % of the coolant). 16. Recycling After unpacking the appliance, the packing materials should be delivered to a local collection site.
Printed by Océ Hungária Kft. Rev.: 2007. 07. 05.
