IBIS4-A4--I.book Seite 1 Mittwoch, 13.
IBIS4-A4--I.book Seite 2 Mittwoch, 13.
IBIS4-A4--I.book Seite 3 Mittwoch, 13. März 2019 9:43 21 IBIS4 Explanation of symbols Original instructions Please read this instruction manual carefully before installation and start-up, and store it in a safe place. If you pass on the device to another person, hand over this instruction manual along with it. Table of contents 1 D ! ! A I AU 1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Safety and installation instructions . . . . . . . . . . . .
IBIS4-A4--I.book Seite 4 Mittwoch, 13. März 2019 9:43 21 Safety and installation instructions 2 IBIS4 Safety and installation instructions Please observe the prescribed safety instructions and stipulations from the vehicle manufacturer and service workshops. The manufacturer accepts no liability for damage in the following cases: 2.
IBIS4-A4--I.book Seite 5 Mittwoch, 13. März 2019 9:43 21 IBIS4 Target group for this instruction manual • • • I Do not make any alterations or conversions to the device. Never drive through automatic car washes when the roof air conditioner is mounted. If faults occur in the refrigerant circuit, the system must be checked by a specialist company and repaired properly. The refrigerant must never be released into the air.
IBIS4-A4--I.book Seite 6 Mittwoch, 13. März 2019 9:43 21 Scope of delivery 4 IBIS4 Scope of delivery 1 1 2 7 3 5 8 4 6 No. in fig.
IBIS4-A4--I.book Seite 7 Mittwoch, 13. März 2019 9:43 21 IBIS4 Intended use 6 Intended use The IBIS4 air conditioner is designed for installation on the roof of a caravan or recreational vehicle to provide reverse cycle heating and cooling. The device is intended for vehicles with roofs that are from 20 to 100 mm thick. The device must be installed so that it is within ±10° of the horizontal plane. It is not suitable for houses and apartments.
IBIS4-A4--I.book Seite 8 Mittwoch, 13. März 2019 9:43 21 Installation 8 IBIS4 Installation ! 8.1 CAUTION! Beware of injury The roof air conditioner may only be installed by qualified personnel. The following information is intended for technicians who are familiar with the guidelines and safety precautions to be applied. Note on installation Read this installation manual completely before installing the roof air conditioner.
IBIS4-A4--I.book Seite 9 Mittwoch, 13. März 2019 9:43 21 IBIS4 Installation Note on transport 4 A B C • Pay attention to the orientation of the up arrows on the carton. Do not install the unit if it has been upside down for any period of time (fig. 4 A). • Always have someone help you carry the roof air conditioner. • Always lift the roof air conditioner to move it and never drag it over the roof (fig. 4 B). • Do not use the ventilation slots to lift it (fig. 4 C).
IBIS4-A4--I.book Seite 10 Mittwoch, 13. März 2019 9:43 21 Installation IBIS4 • Make sure no combustible objects are stored or installed near the air outlet. A distance of at least 50 cm should be kept. • Make sure that there are no objects within the vehicle which could obstruct the attachment of the air outlet unit or the cooled air from flowing through the swivelling air distribution nozzles.
IBIS4-A4--I.book Seite 11 Mittwoch, 13. März 2019 9:43 21 IBIS4 8.2 Installation Making a new opening 5 A B 40 0m m 36 0m m m 00 m 0m m 4 36 1112 63 360 649 758 85 400 93 105 360 113 = = 48 629 20 – 100 400 240 43 518 579 See fig. 5 ➤ Select an area at the centre on the roof between two longitudinal supports. ➤ Mark the position and size of the opening (preferably 400 x 400 mm or optionally 360 x 360 mm). 6 A B See fig. 6 ➤ Drill out the corners (A).
IBIS4-A4--I.book Seite 12 Mittwoch, 13. März 2019 9:43 21 Installation IBIS4 7 A B 2. 1. See fig. 7 ➤ Before installation, check whether the roof hole needs reinforcing. ➤ If needed, remove the foam according to the width of your reinforcing rails (not in scope of delivery) (A). ➤ Fit the reinforcing rails (B). ➤ If needed, fit a suitable H-frame to provide reinforcement to the roof. 8.3 I 12 Installing in an existing opening NOTE • Existing roof hatch openings in accordance with fig.
IBIS4-A4--I.book Seite 13 Mittwoch, 13. März 2019 9:43 21 IBIS4 Installation 8 See fig. 8 ➤ Remove all screws and fixtures of the existing roof hatch or air conditioner. ➤ Take out the roof hatch or air conditioner. 9 See fig. 9 ➤ Remove the sealant around the opening using a scraper or similar tool.
IBIS4-A4--I.book Seite 14 Mittwoch, 13. März 2019 9:43 21 Installation IBIS4 See fig. 0 A 8.4 D NOTICE! Observe the sealant manufacturer’s instructions. ➤ Seal the screw holes and recesses with a flexible non-hardening butyl sealing compound (e.g. SikaLastomer-710, Selleys Butyl Mastic, Bostik ezycaulk butyl sealant, or similar products).
IBIS4-A4--I.book Seite 15 Mittwoch, 13. März 2019 9:43 21 IBIS4 Installation b See fig. b ➤ Orientate roof frame based on opening size. ➤ Fit the roof frame into the roof opening ➤ Seal around the roof frame with flexible non-hardening butyl sealing compound (e.g. SikaLastomer-710, Selleys Butyl Mastic, Bostik ezycaulk butyl sealant, or similar products). c See fig. c ➤ Lift the roof air conditioner onto the roof of the vehicle.
IBIS4-A4--I.book Seite 16 Mittwoch, 13. März 2019 9:43 21 Installation IBIS4 Attaching the roof air conditioner d See fig. d ➤ Use the corners of the front of the base pan to help align the unit with the roof plate.
IBIS4-A4--I.book Seite 17 Mittwoch, 13.
IBIS4-A4--I.book Seite 18 Mittwoch, 13. März 2019 9:43 21 Installation IBIS4 f 2 3 1. 2. 1 3. See fig. f Mains voltage cable ➤ Connect the roof air conditioner with the mains voltage supply. Connect the cables (1) to a cable connector (2). Communication cable ➤ Pull out the filter slightly to create a gap for the communication cable (3). ➤ Feed the communication cable through the gap and locate the wire in the opening.
IBIS4-A4--I.book Seite 19 Mittwoch, 13. März 2019 9:43 21 IBIS4 Installation g See fig. g ➤ Stack the duct sections and place against the roof thickness: the duct height should match the roof height. Or use the below table as a guide: I Roof thickness Number of duct sections 18 – 28 mm 1 28 – 38 mm 2 38 – 48 mm 3 48 – 58 mm 4 58 – 68 mm 5 NOTE Additional duct sections can be purchased for thicker roofs. ➤ Attach the required number of duct sections on the ADB.
IBIS4-A4--I.book Seite 20 Mittwoch, 13. März 2019 9:43 21 Installation IBIS4 h A 2.5±0.3 Nm See fig. h A NOTICE! Risk of damage Tighten to the specified torque. Do not overtighten! ➤ Tighten the screws using a torque spanner and a fastening torque of 2.5 Nm ±0.3 Nm. Communication cable ➤ Connect the communication 4 pin plug into the socket on the side of the display (2) in the ADB. ➤ Ensure the cable is located into the small opening away from the filter area. ➤ Secure excess cable into the holders.
IBIS4-A4--I.book Seite 21 Mittwoch, 13. März 2019 9:43 21 IBIS4 9 Technical data Technical data Contains fluorinated greenhouse gases. Hermetically sealed equipment. IBIS4 IB36H401RI, IB36H401RIY Compressor capacity: 3600 W Cooling capacity based on ISO 5151: 2625 W Heating capacity based on ISO 5151: 3017 W Rated input voltage: 220 – 240 Vw/ 50 Hz Rated current in cooling mode: 6.9 A Rated current in heating mode: 6.
IBIS4-A4--I.book Seite 22 Mittwoch, 13.
IBIS4-A4--I.book Seite 23 Mittwoch, 13.
YOUR LOCAL SUPPORT YOUR LOCAL SALES OFFICE dometic.com/dealer dometic.com/contact dometicĶ ,*ű0 )"0Ŗ,= "s 4445102830 YOUR LOCAL DEALER 4450017950 dometic.com 54-606-MA02 03/2019 IBIS4-A4--I.book Seite 24 Mittwoch, 13.
