Specifications

ManualsBrandsDometic ManualsHeat Pump59136.521

USA

SERVICE OFFICE

The Dometic Corp.

509 So. Poplar St.

LaGrange, IN 46761

(219) 463-4858

CANADA

Dometic Dist.

866 Langs Dr.

Cambridge, Ontario

CANADA N3H 2N7

(519) 653-4390

For Service Center

Assistance Call:

800-544-4881

Form No. 3106593.027 9/95

(Replaces 3106593.001,.019)

LaGrange, IN 46761

INSTALLATION

INSTRUCTIONS

CERTIFIED

LR23565

637G

630 Series PENGUIN

600 Series PENGUIN

579 Series BRISK AIR

595 Series QUICK COOL

591 Series HEAT PUMP

Roof Top Air Conditioners & Heat Pumps

THIS UNIT IS DESIGNED FOR OEM INSTALLATIONTHIS UNIT IS DESIGNED FOR OEM INSTALLATION

THIS UNIT IS DESIGNED FOR OEM INSTALLATION

ALL INITIAL INSTALLATIONS MUST BE APPROVED BY THE DOMETIC CORP.ALL INITIAL INSTALLATIONS MUST BE APPROVED BY THE DOMETIC CORP.

ALL INITIAL INSTALLATIONS MUST BE APPROVED BY THE DOMETIC CORP.

57908

57912

57915

59136

59516

600312

600315

630035

MODELS

Part No. 3106481.009

Electronic Control Kit

USED WITH

RECORD THIS UNIT INFORMATION FOR FUTURE REFERENCE:

Model Number

Serial Number

Date Purchased

Improper installation, ad-

justment, alteration, service

or maintenance can cause

injury or property damage.

Refer to this manual. For

assistance or additional

information consult a quali-

fied installer or service

agency.

Une mauvaise installation, de

mauvais réglages, modifications ou

opérations d’entretien peuvent

endommager les biens ou même

blesser. Se reporter à la notice. Pour

obtenir de l’aide ou des

reseignements complémentaires,

consulter un installateur qualifié ou

une agence de service après-vente.

Summary of content (12 pages)

PAGE 1
® RECORD THIS UNIT INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Date Purchased 630 Series PENGUIN 600 Series PENGUIN 579 Series BRISK AIR 595 Series QUICK COOL 591 Series HEAT PUMP USED WITH Roof Top Air Conditioners & Heat Pumps USA SERVICE OFFICE The Dometic Corp. 509 So. Poplar St. LaGrange, IN 46761 (219) 463-4858 CANADA Dometic Dist. 866 Langs Dr. Cambridge, Ontario CANADA N3H 2N7 (519) 653-4390 Part No. 3106481.
PAGE 2
SPECIFICATIONS MODEL NO. 57908 .521 Nominal Capacity (BTU/HR) * 7,100 59516 .501 .506 .601 .606 57915 57915 57915 .522 .621 .622 .521 .421 .622 .426 .422 .526 .626 57912 .621 11,000 13,500 Electrical Rating 13,500 13,500 59136.521 600312 .321 600312 .421 600315 .321 600315 .421 630035 .421 15,000 15,000 11,000 11,000 13,500 13,500 13,500 12.9 12.9 9.5 10.7 12.4 11.5 11.5 115 VAC, 60 Hz., 1 ph. Compressor Rated Load Amps 6.6 8.5 11.5 12.1 11.
PAGE 3
INSTALLATION INSTRUCTIONS 1. PRECAUTIONS WARNING It is preferred that the air conditioner be installed in a relatively flat and level roof section measured with the RV parked on a level surface; however, a. Up to an 8o slant to either side, or front-to-back, is acceptable on 600 and 630 Series units b. Up to a 15° slant to either side or front-to-back is acceptable on 591 Series Heat Pumps. IMPROPER INSTALLATION MAY DAMAGE EQUIPMENT, COULD ENDANGER LIFE, CAUSE SERIOUS INJURY AND/OR PROPERTY DAMAGE. A.
PAGE 4
B. The total Cross-Sectional Discharge Area of outlet ducts from the Plenum Area under the Air Conditioner must be as follows: 1. 579 & 600 Series; 17.5 sq. in. 2. 591, 595 & 630 Series; 21.0 sq. in. J. Total System Pressure must be between the following: 1. 0.55 to 0.90 in.W.C. for 579 Series 2. 0.40 to 1.10 in.W.C. for 591, 595 & 630 Series 3. 0.12 to 0.65 in W.C. for 600 Series This is determined with the Air Conditioner Blower operation on High Speed and Return Air Filter and Grille in place. C.
PAGE 5
7) Route a dedicated 12 VDC supply line (18-22 AWG) from the RV's Converter or Battery to the roof opening. a. This supply line must be located in the front portion of the 14" opening. b. Make sure that at least 15" of supply wire extends into the roof opening. c. In a multiple zone installation, this wiring is required in only one of the 14" openings. THERE MAY BE ELECTRICAL WIRING BETWEEN THE ROOF AND THE CEILING. DISCONNECT ALL POWER SUPPLIES AND THE POSITIVE (+ ) TERMINAL FROM THE SUPPLY BATTERY.
PAGE 6
11) Route a 4-conductor telephone cable from the Comfort Control Center™ mounting position into the 14" roof opening. Make sure that at least 15" of the wire extends into the roof opening and 6" extend from the wall at the mounting position of the Comfort Control Center™. Terminate the start of the Duct at the back edge of the 14" opening previously cut. FIG.
PAGE 7
C. COMFORT CONTROL CENTER™ INSTALLATION 5. DOMETIC COMFORT CONTROL CENTER ™ & CABLE INSTALLATION 1) Carefully remove the base plate from the Comfort Control Center™. This may be accomplished by inserting a screwdriver under the tab on the bottom edge of the front cover and gently prying. (See FIG. 6). A.
PAGE 8
Control Kit package. 5) Take the ceiling template and hold up to the 14" opening. 6) Start each mounting bolt through the ceiling template and up into the unit base pan by hand. 7) Evenly tighten mounting bolts to a torque of 40 to 50 Inch Pounds. This will compress the roof gasket to approximately 1/2". The bolts are self locking so over tightening is not necessary. 8) Install wood screw in each end of ceiling template. This insures a tight fit of return air cover to ceiling. C.
PAGE 9
NOTE C. INSTALLATION OF ELECTRONIC CONTROL KIT The adhesive on double sided tape is extremely sticky. Divider Plate must be properly positioned before pressing in place. NOTE: If your installation includes the optional Electric Heat Kit, install it at this time. This optional Heat Kit is approved for use on 595 Series Air Conditioners only. Follow the instructions with the heat package for its installation procedure. FIG.
PAGE 10
2) 3) 4) 5) evaporator. (See FIG. 15). a. Locate vertical return bend at lower right of evaporator coil. b. Place the horseshoe end of the Freeze Control onto this coil return bend and snap into place. When positioned correctly, control wires will be 90 degrees to the direction of the coil fin surface. Plug the unit electrical cord into the mating connector on the Electronic Control Kit. These connectors are polarized and will easily snap together. DO NOT FORCE.
PAGE 11
functioning, perform the following configuration procedure: a. Simultaneously depress the UP and DN pushbuttons on the Comfort Control Center™ for one second. This completes the system configuration. SUPPLY 1) Route the previously run power supply line through the Romex Connector and into the Electronic Control Kit Junction Box. 2) Connect the white to white; black to black; and green to green or bare copper wire using appropriate sized twist wire connectors.
PAGE 12
UNIT FIELD WIRING DIAGRAM (A/C) HEAT PUMP FIELD WIRING 12