® Model: TC05 If any quality problems or confusion, feel free to contact us via +1(833)-220-1900 support@dogcareglobal.
1 120Minutes Complete charging for 2 hours. Offer only one wire in the package. 2 Collar Fitting: Adjust to the comfortable size; make sure the receiver’s contact points are placed snugly against your pet’s skin.
Hold 1.5seconds To turn the transmitter and receiver on. 4 Security Keypad Lock: Toggle it down to unlock.
5 Vibrate Command: Press the vibration button briefly and the receiver vibrates once. 6 Beep Command: Press the beep button briefly and the receiver beeps once.
7 Static Intensity Adjustment: Press and hold the LEVEL button while rotating the remote control switch to adjust the shock intensity. Static Command: Press the static button briefly and the receiver shocks once. 8 Channel Switching: Able to train 3 dogs at the same time. Toggle the channel button to select the dog to train.
9 Pairing: Refer to “Page10” for more information. COLLAR STATIC STIMULATION QUICK GUIDE When wearing the collar, it is most suitable if one finger can be insert ed under it. Too tight is not good for your dog, but too loose will dull the static function for the electrodes cannot touch your dog’s skin. Not feelling the SHOCK? Try these solutions. If your dog has thick fur, please separate the fur apart so that both electrodes can touch the skin.
Note: 1. Only when both electrodes are simutaneously touched, shock will work. 2. If collar has a delayed reaction or fails to sync up even in short distance, make sure there is no strong signal interference in your surroundings. The remote's range could be affected by obstacles, electromagnetic field, or even stormy weather. 3. If you find collar cannot work, please check whether you push the lock button on which is on the left side of remote. 4.
Remote Control 10 2 1 3 5 4 11 6 7 8 12 15 9 13 14 On/Off Button (Static 1 Intensity Regulator) 6 Static Mode Button 11 LED Indicator Light 2 Antenna 7 Vibrate Mode Button 12 Charging Port 3 Security Keypad Lock 8 Beep Mode Button 13 On/Off Button Static Intensity Adjustment Button 14 Charging Port 15 Contact Points 4 LCD Display 9 Channel Switching 5 Button Pairing Button 10 (Reverse Side) Screen Signal Transmission Status Security Keypad Lock Static Intensity Remote Cont
Ⅱ．Set up 1. Charge the devices respectively for 2 hours and above. a. Remote control: The battery icon of remote control will be full after it is fully charged. b. Receiver: When red light on the receiver turns green, it is fully charged. When the red light flashes, it is low battery. Set up the voltage level. Press and hold Static Intensity Adjustment Button and simultaneously rotate Static Intensity Regulator until the digit on the screen reaches a suitable intensity.
5.If your dog has thick hair, please separate the hair at the electrodes with a comb from the Contact Points area so that Contact Points are placed snugly against your pet’s skin. 6.When properly fitted, you should be able to fit a finger or two snugly in between the collar and your pet’s skin. Ⅳ. Training Mode 1.Press the vibration button briefly, and the receiver vibrates once; hold the button, and the receiver vibrates continues. 2.
Ⅴ. How to pair the remote with multiple receivers Pair the remote control and receiver This dog training collar supports maximum 3 receivers with only 1 remote control. (Remote control and receiver have been paired with channel #1 from delivery.) 1. Toggle the channel switching button, and select channel 2 or 3. After selecting, the display will show the channel number. 2.
4. The Receiver doesn't respond. ● Make sure the Receiver had been paired. ● Check your Remote control, make sure this Receiver is on the corresponding channel. ● Check your Remote control, make sure the Receiver and Remote control have enough power. 5. The training system has no effect on my dog. ● Make sure the Receiver has been turned on and the Contact Points are placed snugly against your pet’s skin. ● Try increasing the Shock/Static level. 6. The training mode is only available in short range.
Ⅷ. Safety Guidelines 1. It is strictly prohibited to disassemble the receiver in any situation, otherwise the waterproof function may be damaged to violate warranty rules. 2. In order to guarantee normal diving function, please insert the waterproof rubber charging lid in place. 3. Please use remote control and receivers of a complete set, and do not use other product to pair with the receiver. 4. If you want to test the product, please use professional test accessories provided.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
