SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Van Conversions/Campers . . . . . . . . . . . . . . . . . 5 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment. NOTE: It is illegal to remove the VIN plate.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 Power Wagon Things To Know Before Starting Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Instrument Panel And Controls . . . . . . . . . . . .12 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Emergencies . . . . . . . . . . . . . . . . . . . . . . . . . .12 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . .25 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .35 ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .26 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .35 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .27 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .36 ▫ Programming Additional Transmitters . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 䡵 Engine Break-In Recommendations . . . . . . . . . . .70 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 ▫ Transporting Passengers . . . . . . . . . . . . . . . . .71 ▫ Lock Your Vehicle . . . . . . . . . . . . . . . . . . . . . .72 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .72 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER WAGON: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Your Power Wagon is a specialty vehicle, equipped with several features not available on other production trucks. It is very important that you read the following sections of the owner’s manual before operation. Features (See page 80 for more information.) Instrument Panel and Controls (See page 155 for more information.) Operation (See page 220 for more information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN. This number is required for dealer replacement of keys.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The new Sentry Key has been programmed. Repeat this process to program up to an additional 6 keys. A maximum of 8 keys can be programmed to the system, including the original keys provided with the vehicle. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Manual Transmissions When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. To remove the key, depress and hold the release button located between the ignition switch and the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. The key can be inserted or withdrawn only in the LOCK position. Push in on the key in the ignition lock cylinder to rotate to the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR KEY The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn. To lock the doors, insert the key and turn. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock plunger up or down.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Power Door Locks — If Equipped NOTE: Vehicles equipped with remote keyless entry do not have a passenger side door lock cylinder. Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking — If Equipped Vehicles with security will have a feature called ⬙Central Locking⬙. When the key is placed in the door cylinder and turned to the ⬙Unlock⬙ position, the security will be disarmed, the illuminated entry will be turned on and that door will be mechanically unlocked. If the key is once again turned to the unlock position within 5 seconds of the first unlock, the remaining doors will unlock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Within 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction. 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Feature Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: Customer Programming sequence to disable or enable: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may be confusing during this programming procedure). 3. Insert the key into the ignition. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the childprotection door lock system. To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! REMOTE KEYLESS ENTRY — IF EQUIPPED Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. 5. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 9. Test the park lamp flash feature by pressing the LOCK button on the key fob with the ignition in the OFF position or the key removed. 3. Place the key into the ignition. 10. To reactivate this feature, repeat the above steps. 4. Turn the ignition to the ON position (Do not start the engine). 11.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE door locks and remote keyless entry systems will function normally. Panic mode will not disarm the security system on vehicles so equipped. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). Programming Additional Transmitters Vehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 9. A single chime will be heard. The chime indicates that the fob has been recognized. 10. Within 4 seconds of hearing the chime, press and release any button on the fob being programmed. 11. A single chime will be heard. The chime indicates that the fob has been programmed. 12. Repeat steps 8 to 11 for a total of 4 fobs. 13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode. 14.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. Transmitter Battery Service 1. With transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the batteries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly. For an additional 15 minutes only the headlights and security telltale will flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver’s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. The Security system will also disarm, if the vehicle is started with a programmed Sentry Key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WINDOWS Power Windows—If Equipped 2 The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab models. The windows will operate only when the ignition switch is turned to the ON or ACC (Accessory) position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt buckled into the wrong buckle will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! Detaching Buckle with Key 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate In Use Position
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that serves you best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode (if Equipped) In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is only available on the front passenger side belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal injuries is greater. Wear a lap belt low and snug.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These airbags are certified to the new Federal regulations that allow less forceful deployments. WARNING! • Do not put anything on or around the airbag covers or • • This vehicle may also be equipped with window bags to protect the driver and passengers in the first and second row sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Airbags inflate in moderate to high speed impacts. Along with the seatbelts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All occupants should use their seat belts properly. • The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Airbag System Components The airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag The Window Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Window Bags Above the Side Windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in milliseconds. This is less time than it takes you to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The passenger front airbag is to be turned off only if the passenger: WARNING! • is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, nec
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 To Turn On the Passenger Airbag (Standard Cab Vehicles Only) Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key from the switch. This will turn on the passenger airbag. The “Off” light near the switch will be off when the ignition switch is turned to the ON position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags can’t protect you in another collision. Have the airbags replaced by an authorized dealer as soon as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 The side (window) impact SRS Airbags are designed to activate only in certain side collisions. When the airbag control module detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the side pillar molding out of the way and covers the window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag Systems WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control module may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check fuse numbers 52 and 53 in the fuse and relay center. See your dealer if the fuse is good. Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt. • The infant carrier is only used rearward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 with a front shield and are held in the vehicle by the lap portion.) For further information refer to www.seatcheck.org. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Identification dots are located above the standard cab front seat lower anchorages as a guide for locating lower anchors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating positions only. A child may be placed in the rear center seating position of a Quad Cab model using the seat belt and child tether anchorage. Failure to follow this may result in serious or fatal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. An incorrectly anchored tether strap could lead to seat failure and injury to the child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. Multiple Child Restraint Installation Sequence (Quad Cab Rear Seats) 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat. 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 2 Multiple Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. • Limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lock Your Vehicle Always remove the keys from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving articles of value exposed. Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a potentially toxic gas that by itself is colorless and odorless.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed. If there is any question regarding belt or retractor condition, replace the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Outside The Vehicle Door Latches Check for positive closing, latching and locking. Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Power Wagon Features . . . . . . . . . . . . . . . . . . . .80 ▫ Skid Plates And Underbody Protection . . . . . . .82 ▫ Locking Front And Rear Differentials . . . . . . . .80 ▫ Wheel Flares . . . . . . . . . . . . . . . . . . . . . . . . . .82 ▫ 4.56:1 Gears . . . . . . . . . . . . . . . . . . . . . . . . . .80 ▫ Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 ▫ Electronically Disconnecting Stabilizer/Sway Bar . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .86 ▫ Adjustable Head Restraints . . . . . . . . . . . . . . 104 ▫ Electronic Power Mirrors — If Equipped . . . . . .87 ▫ Manual Rotary Lumbar Support Adjustment — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 105 ▫ Electric Rear Window Defroster And Heated Sideview Mirrors — If Equipped . . . . . . . . . . .88 ▫ Power Seats — If Equipped . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 113 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . 119 ▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . 113 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . . 120 䡵 Multifunction Control Lever . . . . . . . . . . . . . . . 113 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . 121 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Trip Odometer (ODO) . . . . . . . . . . . . . . . . . . 126 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 ▫ Elapsed Time (ET) . . . . . . . . . . . . . . . . . . . . . 126 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . . 136 ▫ C/T Button . . . . . . . . . . . . . . . . . . . . . . . . . 126 ▫ Opening Sunroof - Express . . . . . . . . . . . . . . 137 ▫ Automatic Compass Calibration . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 䡵 Cigar Lighter And Ash Receiver . . . . . . . . . . . . 140 ▫ Storage And Seats — If Equipped . . . . . . . . . . 143 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 䡵 Fold Flat Load Floor — If Equipped . . . . . . . . . 144 ▫ Front Instrument Panel Cupholders — Automatic Transmission Only . . . . . . . . . . 141 ▫ Fold Flat Load Floor — If Equipped . . . . . . . . 144 ▫ Rear Cupholder — Quad Cab — If Equipped . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER WAGON FEATURES Locking Front and Rear Differentials Most 4WD trucks are equipped with open differentials front and rear. This design is used because it allows each wheel to turn independently helping to eliminate binding when cornering. A disadvantage of using an open differential is when one or more wheels lose traction; all of the power is directed to those wheels resulting in a loss of momentum.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Electronically Disconnecting Stabilizer/Sway Bar Stabilizer bars are used to help distribute load force from one side of the vehicle to the other. This helps to reduce body roll and create a smoother ride during on-road driving. However, this becomes a disadvantage when the vehicle is driven off-road when a higher level of suspension articulation is needed. By disconnecting the stabilizer bars, each wheel can now reach its maximum range of movement.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High-Pressure Monotube Shocks/New Front and Rear Springs The new variable-rate shocks and revised springs help to create a suitable on-road ride without compromising off-road competency. The shocks are designed to provide improved stability, durability, and suspension articulation. Off-Road Tires These tires are specifically designed for extreme off-road use, while also maintaining quite on-road operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Wheels Stylish forged aluminum 17⬙ wheels give the Power Wagon a powerful stance. Forging a wheel from aluminum produces a stronger, lighter weight wheel than machining or casting the wheel out of the same material. • Steering Dampener Skid Plate - protects the steering dampener from impingement damage. Standard package features: • Electronically Disconnecting Stabilizer/Sway Bar - improves mobility and articulation by disconnecting the Stabilizer/Sway Bar.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Off-Road Tuned Suspension And Shocks - improves mobility, ground clearance and ride comfort. • Gloves • “Power Wagon embossed” storage bag • Heavy Duty Thermally Protected and Sealed Electric Winch With Roller Fairlead - Useful for work and vehicle recovery. • Bed Liner - protects the bed from impingement damage • 17 Inch Forged Aluminum Wheels With 33 Inch Tires - improves traction and differential ground clearance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 3 Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Electronic Power Mirrors — If Equipped 3 The controls for the power mirrors are located on the driver’s door trim panel. Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature. These features also turn off after activation, when 15 minutes have elapsed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in-vehicle communications system. UConnect™; allows you to dial your cellular phone using simple voice commands (e.g., “Call” or “Dial”). Your cellular phone’s audio is transmitted through your vehicle’s stereo system; the system will automatically mute your radio before receiving or sending a call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 prompts as well as the other party’s voice in a conversation will be played over your vehicle’s stereo system. The volume of the UConnect™ system can be controlled through your normal stereo controls. The radio display will be used for visual prompts from the UConnect™ system such as caller ID. The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pairing a Cellular Phone to the UConnect™ System To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone. To complete the registration process, you will need to reference your cellular phone owner’s manual. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup⬙. • When prompted, say “ Phone Pairing”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Making a Phone Call Using Digit Dialing • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number you wish to dial. For example, you can say ⬙Dial” wait for ready prompt 123 456 7890. The phone number that you enter must be a valid length. Making a Phone Call Using Your UConnect™ Phonebook • Press the “Phone” button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system will allow you to enter up to 32 names into the phonebook with each name having up to four associated phone numbers and designations. Edit Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook Edit⬙. • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation that you wish to edit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • After you enter the name, the UConnect™ system will ask you if you wish to delete the home, work, mobile, or pager number for this entry. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook Delete All⬙. • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the stereo audio and will ask if you would like to answer the call by pressing the ’Phone’ button. Press the ’Phone’ button to answer the call. To reject the call, press the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt, say ⬙Setup⬙. If you would like to connect or disconnect the Bluetooth™ connection between a paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. • When prompted, say “ Phone Pairing”. List Paired Cellular Phone Names • At the next prompt, say ⬙Delete⬙. • Press the ’Phone’ button to begin. • You will be asked to say the name of the phone that you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • When prompted, say the phone name of the cellular phone you wish to use, or say ⬙List Phones⬙ to hear a list of all the phones that have been paired to your UConnect™ system. To select a phone from the list, press the ’Voice Recognition’ button and say ⬙Select⬙. • The lower priority phone will only be used for the next phone call. After that, the UConnect™ system will return to using the highest priority phone in the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Language Selection To change the language that the UConnect™ system is using, press the ’Phone’ button and say the name of the language you wish to switch to (English, Español, or Français as equipped). After selecting one of the languages, all prompts and voice commands will be in the selected language. Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Mute/Unmute When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system press the ’Voice Recognition’ button and say ⬙Mute⬙. In order to unmute the UConnect™ system; press the ’Voice Recognition’ button and say ⬙Unmute⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS The seating options available in this truck are the result of extensive customer research and evaluations. 40-20-40 Front Seat WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Each outboard seat is independently adjustable forward or backward and is equipped with a back recliner. The manual seat adjustment handle is found at the front edge of each seat cushion. Pull up on the handle and slide the seat to get the most comfortable position. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! You can be seriously, even fatally injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you. In a collision you could slide under the seat belt and receive serious or fatal injuries. Recline in a seat only when the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar support. Manual Lumbar Adjustment Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat movement. The four-way switch in the center can be moved forward or backwards to get the most comfortable position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls. The engine must be running for the heated seats to operate. Heated Seat Switches Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain the desired heating position and press a second time in the same direction to turn the heated seats OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must reach into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights Courtesy/ dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob. Rotating the dimmer control to the optional fully upward position will turn on the cargo light located on the back of the cab.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Battery Saver To protect the life of your vehicle’s battery, Load Shedding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 15 minutes or the dimmer control is rotated upwards for 15 minutes, the interior lights will automatically turn off. If the headlamps remain on while the ignition is cycled off, the exterior lights will automatically turn off after 5 minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ⬙LAMP OUT⬙ indicator will be illuminated in the instrument cluster if a defective bulb or wiring circuit is detected for the headlamp system. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Lights-on Reminder If the headlights, parking lights, courtesy lights or cargo lights are left on, after the ignition is turned off, a continuous chime will sound when the driver’s door is opened. Fog Lights — If Equipped The foglights are turned ON by placing the headlight rotary control in the parking light or headlight position and pulling out the headlight rotary control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate. Also, the ⬙LAMP OUT⬙ indicator in the instrument cluster will be illuminated and a chime will be heard.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam. Windshield Wipers 3 The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator operation at speeds greater than (refer to the table below for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CANCEL button will deactivate speed control without erasing the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established. Tapping the ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed increases so that tapping the button three times will increase speed by three increments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: • Universal Garage Door Opener — If Equipped Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 OVERHEAD CONSOLE WITH COMPASS/TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: This overhead console allows you to choose between a compass/temperature display and one of four trip conditions being monitored. US/M Button • Courtesy Lights 3 • Compass/Temperature Mini-Trip Computer (CMTC) Use this button to change the display from U.S. to metric measurement units.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE RESET Button Global Reset If the RESET button is pressed twice within 4 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays. Step Button Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time Use this button to choose or cycle through the four trip conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is connected or disconnected).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Trip Odometer (ODO) This display shows the distance traveled since the last reset. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. C/T Button Use this button to select a readout of the outside temperature and one of eight compass headings that indicate the direction in which the vehicle is facing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the CAL symbol will be displayed. After completing one 360° turn, with the vehicle traveling less than 5 mph (8 km/h), in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Put Into a Calibration Mode Turn on the ignition and set the display to “Compass/ Temperature.” Press and hold the RESET button to change the display between VAR (compass variance) and CAL (compass calibration) modes. When the CAL symbol is displayed complete one 360 degree turn in an area free from large metal objects or power lines. The CAL symbol will turn off and the compass will function normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Press and hold the two outer HomeLink buttons, and release only when the indicator light begins to flash (after 20 seconds). Do not hold the buttons for longer than 30 seconds and do not repeat step one to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons. WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held transmitter buttons. Do not release the buttons until step 4 has been completed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button. (The name and color of the button may vary by manufacturer.) NOTE: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.) Proceed with ⬙Programming⬙ step four to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security If you sell your vehicle, be sure to erase the frequencies. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To erase all of the previously trained frequencies, hold down both outside buttons until the green light begins to flash. HomeLink威 is a trademark owned by Johnson Controls, Inc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof - Express Press and release the ⬙V⬙ button, and the sunroof will open to the vent position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 closed by pushing on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes. To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable. CUPHOLDERS Front Instrument Panel Cupholders — Automatic Transmission Only Your new Ram truck is equipped with dual-opening adjustable cupholders.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholder — Quad Cab — If Equipped Quad Cab vehicles may be equipped with a rear cupholder that consists of two cupwells for rear passenger convenience. STORAGE Center Storage Compartment — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. • In an accident, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.5 kg). These items could be thrown about endangering occupants of the vehicle. Items stored should not exceed a total of 10 lbs (4.5 kg).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLD FLAT LOAD FLOOR — IF EQUIPPED Fold Flat Load Floor — If Equipped Quad Cab models with a 60/40 rear seat, may be equipped with a folding steel load floor. WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3 3. Reverse the procedure to store the load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. WARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 PICKUP BOX You can carry wide building materials (sheets of plywood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor. WARNING! The pickup box is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. The pickup box on your new Ram has many features designed for utility and convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Care should always be exercised when operating a vehicle with unrestrained cargo. Vehicle speeds may need to be reduced. Severe turns or rough roads may cause shifting or bouncing of the cargo that may result in vehicle damage. If wide building materials are to be frequently carried, the installation of a support is recommended. This will restrain the cargo and transfer the load to the pickup box floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Raise the right side of the tailgate until the right side pivot clears the hanger bracket. Slide the entire tailgate to the right to free the left side pivot. Remove the tailgate from the vehicle entirely. Do not carry the tailgate loose in the truck pickup box. NOTE: Dual rear wheel pickup models require properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 155 ▫ Scan Button (Radio Mode) . . . . . . . . . . . . . . . 168 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 156 ▫ Cassette Player Features . . . . . . . . . . . . . . . . 169 䡵 Instrument Cluster Description . . . . . . . . . . . . . 157 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 170 䡵 Electronic Digital Clock . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 ▫ Rewind (RW) . . . . . . . . . . . . . . . . . . . . . . . . 177 ▫ Radio Data System (RDS) . . . . . . . . . . . . . . . 173 ▫ Tape Eject . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 ▫ PTY (Program Type) Button . . . . . . . . . . . . . . 174 ▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 178 ▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 153 ▫ Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 190 ▫ Tape CD Button . . . . . . . . . . . . . . . . . . . . . . 181 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 192 ▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 181 䡵 Remote Sound System Controls — If Equipped . . 197 ▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Electric Rear Window Defroster And Heated Sideview Mirrors — If Equipped . . . . . . . . . . 207 ▫ Air Conditioning With Dual Zone Temperature Control — If Equipped . . . . . . . . . . . . . . . . . 207 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 212 ▫ Operating Tips Chart . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 155 INSTRUMENTS AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 157 INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 2. Voltage Gauge When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. If the pointer moves to either extreme left or right and remains there during normal driving, the electrical system should be serviced. NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 7. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously.
UNDERSTANDING YOUR INSTRUMENT PANEL 12. Electronic Throttle Control (ETC) Light 5.7L Engines Only This light informs you of a problem with the Electronic Throttle Control system. If a problem is detected the light will come on while the engine is running. If the light remains lit with the engine running your vehicle will usually be drivable, however, see your dealer for service as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 CAUTION! Do not leave your vehicle unattended with the engine running as you would not be able to react to the temperature indicator if the engine overheats. 14. Security The light will flash rapidly for approximately 16 seconds when the vehicle theft alarm is arming. The light will flash at a slower rate after the alarm is set. The security light will also come on for about two seconds when the ignition is first turned ON. 15.
UNDERSTANDING YOUR INSTRUMENT PANEL 18. Brake System Warning Light This light illuminates when the ignition key is turned to the ON position and remains on for a few seconds. If the light stays on longer, it may be an indication that the parking brake has not been released. This light will illuminate if the brake fluid is low, especially when braking or accelerating hard. This light will illuminate if the ABS indicator light has a malfunction.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 20. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. If the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. The trip odometer shows individual trip mileage. To toggle between the odometer and the trip odometer, press the Odometer/Trip Odometer Button.
UNDERSTANDING YOUR INSTRUMENT PANEL stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required. 24. Low Wash Light This light comes on when the washer fluid level falls below approximately 1/4 filled. The light will remain on until fluid is added and one minute has elapsed. 25. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 28. Transmission Oil Temperature Warning Light This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. If this light comes on, stop the vehicle and run the engine at idle or faster, with the transmission in NEUTRAL until the light goes off. ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button will bypass stations without stopping until you release it. Tune Press the TUNE control up or down to increase or decrease the frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers. Press the AUDIO button a fourth time and FADE will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. The SEEK symbol appears on the display when Music Search is in operation. Music Search shuts off automatically when a selection has been located. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Cassette Mode) Pressing this button while playing a cassette tape will change the side of the tape being played. NR (Noise Reduction) Pushing the Number 2 Pre-set button when a tape is playing deactivates the Dolby Noise Reduction System*. When Dolby is ON, the NR symbol appears on the display. Each time a tape is inserted the Dolby will turn ON. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated. Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer.
UNDERSTANDING YOUR INSTRUMENT PANEL An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS • Disc inserted upside down • Damaged disc • Water condensation on optics RAZ Radio Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down.
UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 To Change From Clock To Radio Mode Press the Time button to change the display between radio frequency and time. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button. The lighted arrow in the display window will show the new direction.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 Operating Instructions — CD Player NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT CD (Eject) Button Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). Time Button Press this button to change the display from elapsed CD playing time to time of day. To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. RBK Radio Seek Press and release the SEEK button to search for the next station in either the AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL the radio will continue to tune until you release the button. The frequency will be displayed and continuously updated while the button is pressed. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Press the AUDIO button a fourth time and FADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and rear speakers. Press the AUDIO button again or wait 5 seconds to exit setting tone, balance, and fade. AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the tracks on the selected disc in random order to provide an interesting change of pace. Satellite Radio (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET RND button. SET 1 will show in the display window. Select the “1–6” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the Power / Volume control pushed ON before the CD player will operate.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load” insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL Scan Press the Scan button to scan through each track on the CD currently playing. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play. This feature plays the tracks on the disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Program Type Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Radio Display Inform Jazz Language News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Program Type Talk Top 40 Weather Radio Display Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SCAN button when the PTY icon is displayed, the radio will stop at every PTY station on the band and list each corresponding program type in the radio display. Time Press the TIME button to change the display from elapsed CD playing time to time of day. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a button in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The center button of the right hand control will allow you to change the mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection. If you press the switch up or down twice it plays the second selection, three times, it will play the third, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Heater Only — Fleet Vehicles NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots. Panel Outside air flows through the outlets located in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Mix Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield, and the demister outlets located at the edge of each side of the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 Temperature Control Air Conditioning—If Equipped The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob. The coldest temperature setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region) of 4 the rotation.
UNDERSTANDING YOUR INSTRUMENT PANEL snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Floor Blower Control Outside air flows primarily through the floor outlets located under the instrument panel. Mix Outside air flows in equal proportions through the floor and defroster outlets, and the air conditioning may be on.
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob. The coldest temperature setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region) of the rotation. Circulation The cab is designed with features to promote outside air circulation. There are grilles in the cab back panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature. These features also turn off after activation, when 15 minutes have elapsed.
UNDERSTANDING YOUR INSTRUMENT PANEL snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. A/C Pushbutton Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be directed through the outlets selected by the mode control.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Recirculation Pushbutton Pushing the Recirculation button allows interior air to recirculate continuously in any position except defrost and defrost/floor mode for rapid cool down of the interior. See “Fast Cooldown” later in this section. Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Heat Blower Control Outside air flows primarily through the floor outlets located under the instrument panel. Mix Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield and side window demist outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL edges of the instrument panel. The demisters also provide extra air ducts for circulation. They are in operation whenever the Floor, Mix or Defrost modes are in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time. This is a normal condition that occurs if the air conditioning system has been on. It is not an indication of a problem with the air conditioning system.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 Axle Locker System . . . . . . . . . . . . . . . . . . . . . 220 ▫ Airing Down For Off-Road Driving . . . . . . . . 240 䡵 Stabilizer/Sway Bar System . . . . . . . . . . . . . . . 223 ▫ Vehicle Recovery . . . . . . . . . . . . . . . . . . . . . . 241 䡵 Power Wagon – Safe Off-Road Driving . . . . . . . 224 ▫ After Driving Off-Road . . . . . . . . . . . . . . . . . 245 ▫ Off-Road Driving Tips And Vehicle Characteristics . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Ignition/Starter Switch . . . . . . . . . . . . . . . . . . . 266 䡵 Transmission Shifting . . . . . . . . . . . . . . . . . . . . 270 ▫ Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 ▫ Automatic Transmission With Overdrive . . . . . 270 ▫ Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 ▫ Manual Transmission — 6-Speed . . . . . . . . . . 275 ▫ On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 217 ▫ Four-Wheel Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 284 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 286 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 286 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 286 ▫ Tire Identification Number (TIN) . . . . . . . . . . 289 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 291 䡵 Tires—General Information . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 309 ▫ Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 309 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 312 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 313 䡵 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 313 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 315 ▫ Certification Label . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 219 䡵 Recreational Towing — 4–Wheel Drive Vehicles (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . . 329 ▫ Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped . . . . . . . . . . . . . 329 䡵 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 䡵 Equipment Identification Plate . . . . . . . . . . . . . 332 ▫ Returning To Normal Operation — Manual Shift Transfer Case . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING Axle Locker System Dodge Power Wagons are equipped with electronically locking front and rear axles. Locking the axles provides greater traction in severe low traction conditions or in rock climbing environments where one wheel is likely to not be in contact with the ground. CAUTION! Do not try to lock the rear axle if the vehicle is stuck and the tires are spinning. You can damage drivetrain components.
STARTING AND OPERATING 221 NOTE: Even when the axles are in the UNLOCK position, the limited slip differential in the rear axle still provides torque biasing capability for moderate low traction environments. During the command to lock the axle, the indicator light will flash until the axle is locked. After the lock command has been successfully executed, the light will remain on solid. Rotary Locking Axle Switch The switch has three positions, UNLOCK, RR, and FR/ RR.
STARTING AND OPERATING NOTE: Left to right wheel speed difference may be necessary to allow the axle to fully lock. If the indicator light is flashing after placing the switch in the RR or FR/RR position, drive the vehicle in a turn or on loose gravel to expedite the locking action. NOTE: The rear axle must be locked before the front axle will lock. WARNING! NOTE: The axle lockers could be torque locked due to side to side loads on the axle.
STARTING AND OPERATING 223 Stabilizer/Sway Bar System Power Wagon vehicles are equipped with an electronic disconnecting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. The switch has two positions, on-road and off-road. The system is normally in on-road mode, indicated by a solid green light. The stabilizer/sway bar should remain in on-road mode during normal driving conditions.
STARTING AND OPERATING To return to on-road mode press the bottom of the stabilizer/sway bar button. WARNING! If stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury. Contact your local service center for assistance.
STARTING AND OPERATING 225 Ramp Travel Index (RTI) The ramp travel index is the distance, in inches, that you can drive your vehicle with one wheel on a 20-degree ramp without lifting any other wheel off the ground. This distance up the ramp divided by the wheelbase of the vehicle and multiplied by 1000 is the RTI. The Power Wagon has an RTI of 655, which means you can articulate one front wheel 32 inches in the air while the other three wheels remain in contact with the ground.
STARTING AND OPERATING Angles A, B, C, and D
STARTING AND OPERATING 227 5 Water Fording
STARTING AND OPERATING Water Fording Characteristics Water fording characteristic is the vehicle’s ability to cross a body of still water, where the powertrain and drivetrain are safe from water ingestion. The Power Wagon has high water fording characteristics with the ability to cross a pool of water, without stopping, 24 inches deep at a maximum speed of 10 mph and a pool of water 30 inches deep at a maximum speed of 5 mph, both with an entrance ramp angle of 1.3 degrees.
STARTING AND OPERATING 229 Simultaneous Brake And Throttle Operation Many off-road driving conditions require the simultaneous use of the brake and throttle (two footed driving). When climbing rocks, logs, or other stepped objects, using light brake pressure with light throttle will keep the vehicle from jerking or lurching. This technique is also used when you need to stop and restart a vehicle on a steep incline. The Basics Of Off-Road Driving You will encounter many types of terrain driving offroad.
STARTING AND OPERATING WARNING! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When To Use Low Range When driving off-road, shift into 4L (Low range) for additional traction or to improve handling and control on slippery or difficult terrain. Due to the lower gearing, low range will allow the engine to operate in a higher power range. This will allow you to idle over obstacles and down hills, with improved control and less effort.
STARTING AND OPERATING 231 CAUTION! On icy or slippery roads, do not downshift at high engine rpm’s or vehicle speeds because engine braking may cause skidding and loss of control. • Mud – Deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use 4L (low range) with a gear low enough to maintain your momentum without shifting.
STARTING AND OPERATING CAUTION! WARNING! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneuvers. Crossing obstacles can cause abrupt steering system loading which could cause you to loose control of your vehicle. Crossing Obstacles (Rocks And Other High Points) While driving off road, you will encounter many types of terrain.
STARTING AND OPERATING 233 Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires. This will lift your undercarriage over the obstacle. The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse. Always look ahead and make every effort to cross the large rocks with your tires. CAUTION! Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.
STARTING AND OPERATING WARNING! CAUTION! There is an increased risk of roll over when crossing an obstacle, at any angle, with steep sides. Do not attempted to cross a log with a greater diameter than the running ground clearance or the vehicle will become high centered. Crossing Logs To cross a log, approach it at a slight angle (approximately 10 to 15 degrees). This allows one front tire to be on top of the log while the other just starts to climb the log.
STARTING AND OPERATING 235 CAUTION! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill Climbing Hill climbing requires good judgment and a good understanding of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and should not be attempted. You should always feel confident with the vehicle and your abilities. You should always climb hills straight up and down. Never attempt to climb a hill on an angle.
STARTING AND OPERATING a 1⁄4 turn quickly back and forth. This will provide a fresh ⬙bite⬙ into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in reverse and back straight down the grade using engine resistance along with the vehicle brakes. WARNING! Never attempt to climb a hill at an angle or turn around on a steep grade. Driving across an incline increases the risk of a roll over, which may result in severe injury.
STARTING AND OPERATING 237 more weight on the down hill wheels, which increases the possibilities of a down hill slide or roll over. Make sure the surface has good traction with firm and stable soils. If possible transverse the incline at an angle heading slightly up or down. WARNING! Driving across an incline increases the risk of a roll over, which may result in severe injury.
STARTING AND OPERATING Driving Through Water Extreme care should be taken crossing any type of water. Water crossings should be avoided if possible and only be attempted when necessary, in a safe responsible manner. You should only drive through areas which are designated and approved. You should tread lightly and avoid damage to the environment. You should know your vehicles abilities and be able to recover it if something goes wrong.
STARTING AND OPERATING 239 crossing is the water depth, current and bottom conditions. On soft bottoms the vehicle will sink in, effectively increasing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross. • Crossing Puddles, Pools, Flooded Areas Or Other Standing Water – Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.
STARTING AND OPERATING downstream out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed determine the speed of the current, the water’s depth, approach angle, bottom condition and if there are any obstacles, then cross at an angle heading slightly upstream using the low and slow technique. WARNING! Never drive through fast moving deep water. It can push your vehicle downstream, sweeping it out of control.
STARTING AND OPERATING 241 CAUTION! Reduced tire pressure increases the risk of tire damage and may cause tire unseating with total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, drive at slower speeds and avoid sharp turns or abrupt maneuvers. Vehicle Recovery If you drive off-road, you may encounter a situation where you will need to recover your vehicle. Vehicle recovery should always be given consideration before attempting a questionable obstacle.
STARTING AND OPERATING CAUTION! Pulling the vehicle off an obstacle, without first clearing the object, may result in additional underbody damage. • Rock Cycling Your Vehicle – Rock cycling your vehicle is one of the easiest, fastest and most commonly used methods. This simply involves shifting your vehicle from drive to reverse, while applying throttle after each shift. During this process, for additional traction, try turning your steering wheel quickly back and forth no more than a 1⁄4 turn.
STARTING AND OPERATING 243 the two drivers. Good communication and line of sight are required for a safe recovery. First connect the tow strap to the correct attachment points on both vehicles. There should be a least 20 to 30 feet between the vehicles to allow for a safe recovery. If necessary join two tow straps together using a 1 1⁄2 inch hard wood dowel. This will keep the straps from becoming knotted and is safer than using a clevis pin if the strap breaks.
STARTING AND OPERATING • Winching (see the section on “Winch Operation” for additional information on the Power Wagon’s winch) – Winching is most commonly used in the following situations: there is no support vehicle available, a high controlled force is required to recover the vehicle, there is a high risk of environmental or vehicle damage, or where nothing else seemed to work. A winch can deliver a high pulling force with a great deal of control.
STARTING AND OPERATING 245 WARNING! Winch cables are under high tension when in use and can become a projectile if they fail. Never stand over or straddle the winch cable. Never jerk or overload the winch cable. Never stand in front of the vehicle while winching. Failure to follow these instructions can result in serious or fatal injury. After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.
STARTING AND OPERATING WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. Failure to do so may result is serious injury. high forces and should be used with care. Do not operate the winch without reading and understanding the complete winch owner’s manual.
STARTING AND OPERATING 247 3. Apply at least 500 lbs. of tension to the rope while winding the rope in. Always use care to ensure the rope does not pile up on one side of the drum and is neatly wound onto the drum. CAUTION! Wire rope must spool on the winch drum in the direction indicated on the drum rotation decal on the winch. Low Voltage Interrupt Your winch is equipped with a device that will interrupt winch function if the vehicle charging system voltage drops to a low level.
STARTING AND OPERATING UNDERSTANDING THE FEATURES OF YOUR WINCH Winch Components
STARTING AND OPERATING 249 1. Motor: The winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote Socket: The remote socket allows the remote control to be attached to the control pack to allow the winch to function. 3. Winch Drum w/ Integral Brake: The winch drum allows the wire rope to be stored on the winch and transmits force to the wire rope.
STARTING AND OPERATING WINCH ACCESSORIES The following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: Wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is extremely important to wear protective gloves while operating the winch or handling the wire rope. Avoid loose fitting clothes or anything that could become entangled in the wire rope and other moving parts.
STARTING AND OPERATING 251 Clevis/D-Shackles: The D-Shackle is a safe means of connecting the looped ends of cables, straps and snatch blocks. The shackle’s pin is threaded to allow easy removal. Tree Trunk Protector: Typically made of tough, highquality nylon, it provides the operator an attachment point for the winch rope to a wide variety of anchor points and objects, as well as protect living trees.
STARTING AND OPERATING General Information Practice using your winch before you get stuck. Some key points to remember when using your winch are: 1. Always take your time to assess the situation and plan your pull carefully. Vehicle Recovery Using the Winch: CAUTION! • Always Know Your Winch: Take time to fully read 2. Always take your time when using a winch. 3. Use the right equipment for the situation. 4.
STARTING AND OPERATING 253 CAUTION! Be careful not to pull the Winch Cable Collar through the rollers. Watch and listen to Winch for proper snugness. 1. Inspect the winch, winch mount, and wire rope for damage. Do not use the winch if the mount is loose or rope shows excessive wear or damage. 2. Put on gloves.
STARTING AND OPERATING 3. Disengage clutch to allow free spooling of the winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserves battery power. 4. Free the winch hook and attach hook strap. Free the winch hook from its anchor point. Attach hook strap to the hook (if not attached).
STARTING AND OPERATING 255 5. Pull wire to anchor point. Pull out enough wire rope to reach your anchor point. Be sure to keep a certain amount of tension on the wire as it can become twisted and over-wrap when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work. 6. Secure to the anchor point. Once you’ve established your anchor point, secure the tree-trunk protector or choker-chain around the object.
STARTING AND OPERATING CAUTION! Always be certain the anchor you select will withstand the load. NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural anchors include trees, stumps and rocks. Hook the cable as low as possible. If no natural anchors are available when recovering another vehicle, your vehicle becomes the anchor point.
STARTING AND OPERATING 257 NOTE: Always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door. Always disconnect the remote control when not in use.
STARTING AND OPERATING 10. Put wire rope under tension. Using the remote control switch, slowly wind the wire rope until no slack remains. Once the wire rope is under tension, stand well clear and never step over it. 11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure. 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope.
STARTING AND OPERATING 259 13. In certain situations you may decide to throw a heavy blanket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway between the winch and the anchor point. Do this before the wire rope is put under tension. Do not approach or move the blanket once tension is applied. Do not allow it to get pulled into the fairlead.
STARTING AND OPERATING For additional assistance, the winched vehicle can be slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground. If you are able to drive the vehicle, the winching operation is complete. Using The Remote Control NOTE: Avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the winch motor to cool down.
STARTING AND OPERATING 261 an uneven stack, spool out that section of the rope and reposition it to the opposite end of the drum, which will free up space for continued winching. 16. Secure vehicle. Once recovery of the vehicle is complete, be sure to secure the vehicle’s brakes and put the transmission in ⬙park⬙ (automatic) or ⬙low⬙ gear for ⬙manual⬙ transmissions. Release tension in the wire rope. 17. Disconnect wire rope. Disconnect from the anchor. 18. Rewind wire rope.
STARTING AND OPERATING Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessary. Keep the wire rope under light tension and spool the wire rope back and onto the winch drum in even layers. Stop frequently to tighten and straighten the layers as necessary.
STARTING AND OPERATING 263 RIGGING TECHNIQUES How to change the pulling direction: Various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or maintaining a straight-line pulling situation. You will have to assess what technique is correct for your situation. Think ⬙safety⬙ at all times.
STARTING AND OPERATING will enable you to change your pulling direction while still allowing the wire rope to be at 90° to wind properly onto the spooling drum. Increasing pulling power: Increase Pulling Power In some cases, you may find yourself needing more pulling power.
STARTING AND OPERATING 265 Double Line: Because pulling power decreases with the number of layers of wire rope on the winch drum, you can use a snatch block to double line out more wire rope. This decreases the number of layers of wire rope on the drum, and increases pulling power. Start by feeding out enough wire rope to free the winch hook. Attach the hook to your vehicle’s frame/tow hook and run the wire rope through a snatch block.
STARTING AND OPERATING IGNITION/STARTER SWITCH NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of Park (P). OFF Unlocks the steering wheel (if equipped with locking wheel) and the automatic transmission shift control with engine off. ON This is the normal running position. LOCK Locks the automatic transmission shift control into the PARK position.
STARTING AND OPERATING 267 ACC Allows the electrical accessories to be used when the engine is not running. Key Reminder An alarm will sound to remind you if the key is left in the ignition and the driver’s door is opened. Manual Transmission Key Release Button STARTING PROCEDURES The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating.
STARTING AND OPERATING Automatic Transmission Start the engine with the selector lever in NEUTRAL or PARK position. Apply the brake before shifting to any driving range. Normal Starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure.
STARTING AND OPERATING 269 If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the normal starting procedure should be repeated. WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. After Starting The idle speed is automatically controlled and will decrease as the engine warms up.
STARTING AND OPERATING TRANSMISSION SHIFTING Automatic Transmission with Overdrive The gear shift selector display, located in the instrument panel cluster, indicates the transmission gear range (the selector is illuminated for night driving). The selector lever is mounted on the right side of the steering column. You must depress the brake pedal, to pull the selector lever out of park (P) position (Brake Interlock System).
STARTING AND OPERATING 271 WARNING! WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling it toward you after you have set it in P. Make sure it is in Park before leaving the vehicle. It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed.
STARTING AND OPERATING “N” Neutral Shift to Neutral when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. “D” Drive This position provides all forward gears, including 3rd gear direct and 4th or 5th (if equipped) gear overdrive (see Overdrive Operation). Use this range for most city and highway driving.
STARTING AND OPERATING 273 • the “TOW/HAUL” switch has not been activated; • transmission has reached normal operating temperature. NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level. Refer also to the Note under torque converter clutch, later in this section.
STARTING AND OPERATING performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking.
STARTING AND OPERATING 275 the fluid partially draining from the torque converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position. G 56 Shift Pattern – If Equipped Manual Transmission — 6-Speed NOTE: The parking brake should be engaged before leaving the vehicle, especially on an incline. This model is equipped with a clutch interlocking ignition system.
STARTING AND OPERATING You should use low gear when starting from a standing position if under a heavy load. To shift into Reverse, come to a complete stop. Depress the clutch and pause briefly to allow the gear train to stop. Move the shift lever from the Neutral position straight across and up into Reverse. Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch.
STARTING AND OPERATING 277 CAUTION! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage. FOUR-WHEEL- DRIVE OPERATION Manually Shifted Transfer Case Operating Information/Precautions The transfer case provides 4 mode positions - 2 (rear)wheel-drive high range, 4-wheel-drive high range, neutral, and 4-wheel-drive low range.
STARTING AND OPERATING Proper operation of 4-wheel-drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. The transfer case is not equipped with a synchronizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place.
STARTING AND OPERATING 279 4H 4-Wheel-Drive High Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Shifting Procedure - Manually Shifted Transfer Case N Neutral - Disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. See Recreational Towing for more information. 4L 4-Wheel-Drive Low Range - Low speed 4-wheel-drive.
STARTING AND OPERATING vehicle in motion, the transfer case will engage / disengage faster if you momentarily release the accelerator pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to N (Neutral) or depress the clutch on a manual transmission.
STARTING AND OPERATING 281 LIMITED-SLIP DIFFERENTIAL — IF EQUIPPED The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit performs similarly to a conventional differential.
STARTING AND OPERATING PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle.
STARTING AND OPERATING 283 WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or first gear. Failure to do so may allow the vehicle to roll and cause damage or injury. • Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured.
STARTING AND OPERATING Brake Noise During normal operation of the brake system certain noises may be present from time to time. Occasional ⬙groan⬙ or ⬙squeal⬙ noises may occur during normal operation of the brake system which may not be indicative of a problem. These noises may be heard at any time the brakes are applied but may be more noticeable during the first few brake applications in the morning.
STARTING AND OPERATING 285 WARNING! WARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
STARTING AND OPERATING POWER STEERING Your power steering system will provide mechanical steering capability if power assist is lost. TIRE SAFETY INFORMATION Tire Markings If for any reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will experience a substantial increase in steering effort. NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING 287 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING EXAMPLE: 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.5 = Section Width in Inches (in) R = Construction Code —⬙R⬙ means Radial Construction. —⬙D⬙ means Diagonal or Bias Construction. 15 = Rim Diameter in Inches (in) Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry.
STARTING AND OPERATING 289 EXAMPLE: —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits). Load Identification: ⴖ....blank....
STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards, and is approved for highway use. MA = Code representing the tire manufacturing location.(2 digits) L9 = Code representing the tire size.(2 digits) ABCD = Code used by tire manufacturer.(1 to 4 digits) 03 = Number representing the week in which the tire was manufactured.
STARTING AND OPERATING 291 Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B” pillar, the Certification Label or in the Tire Inflation Pressures brochure in the glove compartment.
STARTING AND OPERATING Tire and Loading Information Placard 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 293 lbs.” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. Steps for Determining Correct Load Limit 6.
STARTING AND OPERATING
STARTING AND OPERATING 295 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING 297 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING 299 Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING 301 WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle. Failure to do so could result in loss of vehicle control.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING 303 WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passengers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
STARTING AND OPERATING 305 These cautions apply to all chain traction devices, including link and cable (radial) chains. NOTE: On 4x4 Power Wagon models, class “U” snow chains are permitted on the rear wheels only of vehicles equipped with LT285/70R17D. CAUTION! Do not use tire chains on the 4X4 front wheels of Ram Trucks equipped with LT285/70R17D. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle.
STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off Road type tires.
STARTING AND OPERATING 307 FUEL REQUIREMENTS The 5.7L engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89. The manu5.7L Engines facturer recommends the use of 89 octane for optimum performance.The routine use of premium gasoline is not recommended.
STARTING AND OPERATING We strongly support the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
STARTING AND OPERATING 309 Sulfur In Gasoline If you live in the northeast United States, your vehicle may have been designed to meet California low emission standards with Cleaner-Burning California reformulated gasoline with low sulfur. If such fuels are not available in states adopting California emission standards, your vehicles will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be adversely affected.
STARTING AND OPERATING CAUTION! WARNING! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: Tighten the gas cap until you hear a “clicking” sound.
STARTING AND OPERATING 311 CAUTION! WARNING! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive.
STARTING AND OPERATING Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system, and could result in loss of warranty coverage. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING 313 Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.
STARTING AND OPERATING 315 VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.
STARTING AND OPERATING Tire Size This is the minimum allowable tire size for your vehicle. Replacement tires must be equal to the load capacity of this tire size. Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. Rim Size This is the rim size that is appropriate for the tire size listed.
STARTING AND OPERATING 317 Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. An EXAMPLE of a loaded vehicle is shown in the following chart.
STARTING AND OPERATING TRAILER TOWING All Dodge Ram Pickup trucks are intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your Dodge dealer for package content. To Maintain Warranty Coverage Follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
STARTING AND OPERATING 319 CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. • When first towing a trailer, limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing. Consider the following items when computing the weight on the rear axle: NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
STARTING AND OPERATING CAUTION! When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, body structure or tires. Trailer Towing Recommendations • All trailer hitches should be professionally installed on your vehicle. • Safety chains must always be used between your vehicle and trailer.
STARTING AND OPERATING 321 • Use an approved wiring harness connector on the trailer. Standard equipment on all RAM pickup models provides a 4-way trailer tow connector located under the bumper. This connector contains the following vehicle circuits: park/tail lamps, left stop/turn lamp, right stop/turn lamp, and ground. With the optional Trailer Tow Prep package a 7-way connector is provided with the following additional circuits: backup lamp, trailer battery and electric brake.
STARTING AND OPERATING With a Class III Hitch, your vehicle can be equipped to tow trailers with a Gross Trailer Weight (GTW) of 5,000 lbs (2 268 kg) maximum. Factory-installed rear step bumpers are rated a Class III hitch. A frame mounted hitch of up to Class IV rating, as rated by the hitch manufacturer, may also be installed. With a Class IV Hitch, you can tow a trailer with a Gross Trailer Weight of up to 12,000 lbs (5 443 kg) maximum depending on your vehicle equipment.
STARTING AND OPERATING 323 CAUTION! CAUTION! Adding lights or electrical devices to the headlamp/ park lamp circuit can be accomplished by connecting to the standard 4-way trailer tow connector located behind the rear bumper. The maximum current capacity for the park lamp circuit should not exceed 15 amps total (a typical park lamp bulb can draw from 0.5 to 1.0 amperes of current). No connections can be made to the headlamp switch itself, because it is not designed for high current applications.
STARTING AND OPERATING Tongue Weight is the weight placed on the vehicle’s trailer hitch by the trailer. Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle. Tongue weight must be equal to at least 10% of GTW, but no more than 15% of GTW. Trailer sway control and equalizing hitch are required for Class III or IV trailer hitches and tongue weights above 350 lbs (159 kg).
STARTING AND OPERATING 325 • Total weight must be distributed between the tow vehicle and the trailer such that the following four (4) ratings are not exceeded: 1. GVWR 2. GTW 3. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight.) 4.
STARTING AND OPERATING Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface.
STARTING AND OPERATING 327 • Air Conditioning— turn it off temporarily. • Hilly Terrain— Turn overdrive off. See Cooling System Operating information in the Service and Maintenance section of this manual for more information. Automatic Transmission Oil Temperature Warning Light All vehicles with automatic transmissions are equipped with a transmission sump oil temperature sensor and warning light.
STARTING AND OPERATING SNOWPLOW CAUTION! Dodge Power Wagon Models NOTE: Do not use Dodge Power Wagon Models for snowplow applications. Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! WARNING! Snowplows and other aftermarket equipment should not be added to the front end or your vehicle. The airbag crash sensors may be affected by the change in the front end structure.
STARTING AND OPERATING 329 RECREATIONAL TOWING — 4–WHEEL DRIVE VEHICLES (BEHIND MOTORHOME, ETC.) CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: The transfer case must be shifted into Neutral (N) for recreational towing. Automatic transmissions must be placed in P (Park) position for recreational towing. Manual transmissions must be left in gear (not in neutral) for recreational towing.
STARTING AND OPERATING 5. Shift transfer case lever into N (NEUTRAL). 6. Start the engine. 7. Shift automatic transmission into Reverse (R). 8. Release brake pedal for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with the transmission in Drive (D). 10. Shut OFF the engine and place the ignition key to the unlocked OFF position. 11. Shift automatic transmission into P (PARK). 12. Apply the parking brake. 13. Attach vehicle to tow vehicle with tow bar. 14.
STARTING AND OPERATING 331 4. Shift automatic transmission to N (NEUTRAL), or depress the clutch on manual transmissions. 5. Shift transfer case lever to desired position. 6. Shift automatic transmission into P (Park). WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the N (NEUTRAL) position without first fully engaging the parking brake.
STARTING AND OPERATING 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the car in front to avoid a collision in a sudden stop. EQUIPMENT IDENTIFICATION PLATE The equipment Identification Plate is located on the hood inner surface.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Lights . . . . . . . . . . . . . . . . . . 334 䡵 Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 335 䡵 Jump-Starting . . . . . . . . . . . . . . . . . . . . . . . . . 344 䡵 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . 336 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 347 ▫ All Models . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING LIGHTS The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. To engage the Hazard Warning lights, depress the button on the top of the steering column. When the Hazard Warning switch is activated, all directional turn signals will flash off and on to warn oncoming traffic of an emergency. Push the button a second time to turn off the flashers.
WHAT TO DO IN EMERGENCIES 335 ADDING FUEL The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable fuel container, it should have a flexible nozzle long enough to force open the restricting door. WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling.
WHAT TO DO IN EMERGENCIES JACK LOCATION All Models The jack and jack tools are stored under the passenger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by loosening the thumb screw and sliding the assembly from under the seat. WARNING! The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure.
WHAT TO DO IN EMERGENCIES 337 CHANGING A FLAT TIRE Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
WHAT TO DO IN EMERGENCIES Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. Do not raise this vehicle using a bumper jack.
WHAT TO DO IN EMERGENCIES 339 • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. For Power Wagon, when changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front.
WHAT TO DO IN EMERGENCIES 341 WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wheel off. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel on the rear wheel models. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. 6.
WHAT TO DO IN EMERGENCIES WARNING! NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. Hub Caps The hub caps must be removed before raising the vehicle off the ground. 7. Remove wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel.
WHAT TO DO IN EMERGENCIES 343 the nut opposite to the nut just previously tightened until final torque is achieved. Recommended torques are shown in the following chart. Disc Wheels Type Nut Stud Size Torque Ft. Lbs. Cone Flanged 9/16-18 9/16-18 120-150 130-160 Torque Newton Meters 160-200 190-220 To Stow The Flat Or Spare Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening.
WHAT TO DO IN EMERGENCIES JUMP-STARTING You should not try to start your vehicle by pushing or towing. Vehicles equipped with an automatic transmission cannot be started this way and pushing or towing a vehicle equipped with a manual transmission may overheat and damage the catalytic converter. Also, there is a greater risk of an accident when a vehicle is being pushed or towed.
WHAT TO DO IN EMERGENCIES 345 2. Park the booster vehicle within cable reach but without letting the vehicles touch. Set the parking brake on both vehicles, place the automatic transmission in Park or the manual transmission in Neutral, and turn the ignition OFF. 3. Turn off the heater, radio, and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
WHAT TO DO IN EMERGENCIES 347 FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between DRIVE and REVERSE, while applying slight pressure to the accelerator. In general, the least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
WHAT TO DO IN EMERGENCIES CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment— 5.7L . . . . . . . . . . . . . . . 352 䡵 Onboard Diagnostic System (OBD II) . . . . . . . . . 353 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 ▫ Drive Belts — Check Condition And Tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . . 360 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 361 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Power Steering — Fluid Check . . . . . . . . . . . . 367 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 367 ▫ Steering Linkage — Inspection . . . . . . . . . . . . 368 ▫ Front Prop Shaft Lubrication . . . . . . . . . . . . . 368 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 369 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 369 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 369 ▫ Exhaust System . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 351 䡵 Replacement Light Bulbs . . . . . . . . . . . . . . . . . 394 ▫ Tailgate ID Lights (Dual Rear Wheels) . . . . . . . 403 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 394 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 405 ▫ Headlight (Halogen)/Front Park And Turn Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 406 ▫ Tail, Stop, Turn And Backup Lights . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing. Normally, the OBD system will be ready. The OBD system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery replacement.
MAINTAINING YOUR VEHICLE b. The MIL light will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. REPLACEMENT PARTS Use of genuine Mopar威 parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance.
MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the ADD and SAFE markings on the dipstick. Adding one quart of oil when the reading is at the ADD mark will result in a SAFE reading on these engines. 357 Change Engine Oil CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine.
MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 32°C (90°F) • Trailer towing • Heavy Loading • Taxi, Police or delivery service (commercial service) • Off-road or desert operation • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.
MAINTAINING YOUR VEHICLE Engine Oil Identification (API) Symbol There is a symbol to aid you in selecting the proper engine oil. This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395.
MAINTAINING YOUR VEHICLE Materials Added to Engine Oil The manufacture strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle.
MAINTAINING YOUR VEHICLE Belts should be inspected for evidence of cuts, cracks, glazing or frayed cords and replaced if there is indication of damage which could result in belt failure. Low generator belt tension can cause battery failure. Also check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage.
MAINTAINING YOUR VEHICLE WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc) removed. Failure to do so can result in serious personal injury.
MAINTAINING YOUR VEHICLE 363 CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: Emission-Related Components • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. Positive Crankcase (PCV) Valve Proper operation of the crankcase ventilation system requires that the PCV valve be free of sticking or plugging from deposits. Deposits can accumulate in the PCV valve and passages with increasing mileage.
MAINTAINING YOUR VEHICLE 365 WARNING! CAUTION! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Don’t use a booster battery or any other booster source with an output greater than 12 volts.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through a certified DaimlerChrysler Dealership.
MAINTAINING YOUR VEHICLE Front suspension ball joints should be replaced only by a qualified service technician using tools specially designed for this purpose. Damage to the joints and/or suspension components may result if improper replacement procedures are used. Front Prop Shaft Lubrication Lubricate the front driveshaft grease fitting at each oil change listed in the appropriate Maintenance Schedule for your vehicle (Schedule “A” and “B”).
MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
MAINTAINING YOUR VEHICLE To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, follow the preceding safety tips. Exhaust System Rubber Isolator and Loop-Type Hanger — If Equipped Inspect surfaces whenever the vehicle is hoisted for rubber to metal separation or deep cracks. SLIGHT CRACKING DUE TO WEATHERING DOES NOT ADVERSELY AFFECT PERFORMANCE.
MAINTAINING YOUR VEHICLE Check the coolant bottle hoses for condition and tightness of the connections at both the coolant bottle and radiator. Check the coolant pressure cap and coolant reserve system for proper vacuum sealing. With the engine at normal operating temperature, note the level of the coolant in the coolant bottle. Without removing the pressure cap (with the engine off), drain a small amount of coolant from the radiator draincock.
MAINTAINING YOUR VEHICLE Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOAT ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution.
MAINTAINING YOUR VEHICLE Recommended Engine Coolant Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. CAUTION! • Mixing of coolants other than specified engine coolant, may result in engine damage, and decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do not use plain water alone or alcohol base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE Disposal Of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. Do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. Prevent ingestion by animals and children. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure.
MAINTAINING YOUR VEHICLE 377 WARNING! CAUTION! Use of a brake fluid that may have a lower initial boiling point, or is unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
MAINTAINING YOUR VEHICLE Clutch Linkage If the clutch pedal linkage begins to squeak or grunt, the clutch pedal pivot bushings should be lubricated. Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type. For all 2500 Model axles, the fluid level should be 1/4” ± 1/4” (6.4 mm ± 6.4 mm) below the fill hole on the 9.25” Front and 3/4”± 1/4” (19 mm ± 6.4 mm) on 10.5” Rear axles. The 11.5” Rear Axle level should be 1/4” ± 1/4” (6.4 mm ± 6.4 mm) below the fill hole.
MAINTAINING YOUR VEHICLE 379 Limited-Slip Differentials Manual Transmission Power Wagon Axles DO NOT REQUIRE any limited slip oil additive (friction modifiers). Fluid Level Check This fluid level can be checked by removing the filler plug. If the level of the lubricant is more than 1/4” (6.4 mm) below the bottom of the filler hole while the vehicle is on level ground, enough lubricant should be added to bring the level to the bottom of the filler hole.
MAINTAINING YOUR VEHICLE Automatic Transmission Fluid Level Check The fluid level should be checked when the engine is fully warmed up and the fluid in the transmission is at normal operating temperature. Operation of the transmission with an improper fluid level will greatly reduce the life of the transmission and of the fluid. Check the fluid level whenever the vehicle is serviced. Fluid Level Check – 545RFE Check the fluid level while the transmission is at normal operating temperature 82°C (180°F).
MAINTAINING YOUR VEHICLE 381 a minimum of two (2) minutes for the oil to fully drain into the transmission before rechecking the fluid level. CAUTION! NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD” (lower) holes on the dipstick with the fluid at approximately 70°F (21°C) (room temperature).
MAINTAINING YOUR VEHICLE Selection Of Lubricant Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. Automatic Transmission Fluid and Filter Change To obtain best performance and long life for automatic transmissions, the manufacturer recommends that they be given regular maintenance service by an Authorized Dodge Dealer or Service Center.
MAINTAINING YOUR VEHICLE Special Additives The manufacturer strongly recommends against the addition of any additives to the transmission. Exception to this policy is the use of special dyes to aid in detecting fluid leaks. The use of transmission sealers should be avoided, since they may adversely affect seals. Front Wheel Bearings Front wheel bearings for all Dodge Ram Trucks are sealed-for-life. They do not require greasing or seal replacement.
MAINTAINING YOUR VEHICLE quality level available and when combined as shown can be used for both wheel bearing and chassis lubrication. Use only those greases that have the NLGI symbol on the container along with the proper quality level for your application.
MAINTAINING YOUR VEHICLE Required Maintenance for Noise Control Systems The following maintenance services must be performed every 6 months or 6,000 miles (9 600 km), whichever comes first, to assure proper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed or suspected. Proper maintenance of the entire vehicle will help the effectiveness of the noise control systems.
MAINTAINING YOUR VEHICLE AIR CLEANER • Removal of the air cleaner. • Inverting the air cleaner lid. • Removal of the air ducting. EXHAUST SYSTEM • Removal or rendering inoperative exhaust system components including the muffler or tailpipe. ENGINE COOLING SYSTEM • Removal or rendering inoperative the fan clutch. • Removal of the fan shroud.
MAINTAINING YOUR VEHICLE 387 Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed.
MAINTAINING YOUR VEHICLE Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed.
MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants.
MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and tailgate be kept clear and open.
MAINTAINING YOUR VEHICLE • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar威 touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar威 Fabric Cleaner to clean fabric upholstery and carpeting. Use Mopar威 Vinyl Cleaner to clean vinyl upholstery and trim. Mopar威 Total Clean is specifically recommended for leather upholstery.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using.
MAINTAINING YOUR VEHICLE FUSE AND RELAY CENTER 393 2. Use specified fuses only. 3. Always properly reinstall the cover. VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Fuse and Relay Center, located in the engine compartment. The I.O.D.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Bulb No. Overhead Console Lights . . . . . . . . . . . . . . . TS 212-2 Dome Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7679 All of the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved. LIGHT BULBS — Outside Bulb No. Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057 Center High Mounted Stop Lamp . . . . . . . . . . . . . 912 Fog Lamp . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 395 1. Remove the expanding fastener from the headlight welt.
MAINTAINING YOUR VEHICLE 2. Remove the three (3) bolts from the headlight housing. NOTE: The lower bolt on the driver side headlight also retains the ambient temperature sensor between the headlight assembly and the frame.
MAINTAINING YOUR VEHICLE 3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. 397 4. Unlock and pull connector straight from the base of the headlight halogen bulb. 5. Twist connector on turn signal/park light bulb 1⁄4 turn and remove connector and bulb from housing. 6. Remove housing from vehicle with headlight halogen bulb in housing.
MAINTAINING YOUR VEHICLE 7. Twist collar on headlight halogen bulb 1⁄4 turn and remove headlight bulb from the housing. 8. Replace headlight or turn signal bulb. Do not touch the headlight halogen bulb. 9. Reverse procedure for installation of bulbs and housing. 10. Tighten the outboard fastener first. Tail, Stop, Turn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal.
MAINTAINING YOUR VEHICLE 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged. 399 3. Push the red lock slide in on the connector and remove the housing from the vehicle. 4. Remove the four (4) screws from the bulb strip in the housing.
MAINTAINING YOUR VEHICLE 5. Pull the appropriate bulb straight from the bulb strip. 7. While holding the taillight firmly in place, fasten the top screw first. Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. • Top Bulb: Park/Turn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights 6. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE 401 2. Separate the connector holding the housing and wiring harness to the body. • Outside Bulbs: Cargo Lamps 3. Turn desired bulb socket 1⁄4 turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE Cab Top Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. 2. Rotate the socket 1⁄4 turn and pull it from the light assembly.
MAINTAINING YOUR VEHICLE 3. Pull the bulb straight from the socket and replace. 403 Tailgate ID Lights (Dual Rear Wheels) 1. Remove the two screws and housing and access the bulb sockets from the rear.
MAINTAINING YOUR VEHICLE 2. Turn socket 1⁄4 turn counterclockwise to access the bulb. 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE 405 Fog Lights 1. Reach under the vehicle, unlock and twist connector counterclockwise 1⁄4 turn and remove connector and bulb from housing. 3. Reverse procedure for installation of bulbs and housing. 2. Pull bulb straight from the connector.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Metric 34 gal. 35 gal. 128L 132L 7.0 qts. 6.6L 18.7 qts. 17.7L Fuel 5.7L, 89 Octane 2500 Shortbed Models 2500 Longbed Models Engine Oil (with filter) 5.7L Engine V-8, SAE 5W-20, API Certified Cooling System 5.
MAINTAINING YOUR VEHICLE 407 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection (5.7L) Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) P/N 5011764AB or equivalent. Use SAE 5W-20, API Certified, meeting material standard MS-6395. Refer to oil viscosity chart for alternative grade. Mopar威 Engine Oil Filter, P/N 5281090 or equivalent.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Manual Transmission Fluid (G-56) Front Driveshaft Grease Fitting. Clutch Linkage Front and Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar威 ATF+4, Automatic Transmission Fluid Mopar威 ATF+4, Automatic Transmission Fluid Mopar威 ATF+4, Automatic Transmission Fluid Use Mopar威 type MS-6560 (lithium based grease), or equivalent. Multipurpose Grease, NLGI Grade 2 E.P.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 410 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 413 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 410 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 410 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES 411 M • Heavy Loading. • Taxi, police, or delivery service (commercial service). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.
M 412 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B” 413 M Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F C (32°). • Trailer towing. • Snowplowing. • Heavy Loading.
M 414 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months, whichever comes first. N C Lubricate Drive Shaft Fitting. E Rotate tires. S C H E D U L E S 8 Lubricate tie rod end links. Change rear axle fluid. Change front axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” 415 M Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months, whichever comes first. Lubricate Drive Shaft Fitting. Rotate tires. Lubricate tie rod end links. Change rear axle fluid. Change front axle fluid. Check transfer case fluid level. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.
M 416 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months, whichever comes first. N C Lubricate Drive Shaft Fitting. E Rotate tires. S C H E D U L E S 8 Lubricate tie rod end links. Change rear axle fluid. Change front axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” 417 M Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months, whichever comes first. Lubricate Drive Shaft Fitting. Rotate tires. Lubricate tie rod end links. Drain and refill transfer case fluid. Change rear axle fluid. Change front axle fluid. Change 6-spd manual transmission (G-56) fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Replace ignition cables. Inspect PCV valve, replace as necessary.
M 418 SCHEDULE “B” A I N Miles T (Kilometers) E N Drain and refill automatic tranmission fluid and A change main sump filter (545RFE only).
SCHEDULE “B” 419 M Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months, whichever comes first. Lubricate Drive Shaft Fitting. Rotate tires. Lubricate tie rod end links. Inspect engine air cleaner filter. Change rear axle fluid. Change front axle fluid. Inspect brake linings. Inspect auto tension drive belt and replace if required. Flush and replace engine coolant at 60 months, if not done at 102, 000 miles (163 000 km).
M 420 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months, whichever comes first. N C Lubricate Drive Shaft Fitting. E Rotate tires. S C H E D U L E S 8 Lubricate tie rod end links. Change rear axle fluid. Change front axle fluid. Check transfer case fluid level. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.
SCHEDULE “B” 421 M Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months, whichever comes first. Lubricate Drive Shaft Fitting. Rotate tires. Lubricate tie rod end links. Flush and replace engine coolant, if not done at 60 months. Flush and replace Power Steering Fluid. Inspect brake linings.
M 422 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months, whichever comes first. N C Lubricate Drive Shaft Fitting. E Rotate tires. S C H E D U L E S 8 Lubricate tie rod end links. Drain and refill transfer case fluid. Change rear axle fluid. Change front axle fluid. Change 6-spd manual transmission (G-56) fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Replace ignition cables.
SCHEDULE “B” 423 M Miles (Kilometers) Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required. Drain and refill automatic tranmission fluid and change main sump and spin-on cooler return filter (if equipped) [545RFE only]. 105,000 (168 000) X * This applies only if the vehicle is used for frequent trailer towing, snowplowing, fleet vehicle or commercial service. **This maintenance is recommend, but not required.
M 424 SCHEDULE “A” A I Schedule “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Lubricate Front Prop Shaft fitting. S C H E D U L E S 8 Rotate tires. Check transfer case fluid level. Lubricate tie rod end links. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs.
SCHEDULE “A” 425 M Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Prop Shaft fitting. Rotate tires. Check transfer case fluid level. Lubricate tie rod end links. Flush and replace engine coolant at 60 months, regardless of mileage. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Replace ignition cables.
M 426 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Lubricate Front Prop Shaft fitting. E Rotate tires. S C H E D U L E S 8 Lubricate tie rod end links. Check transfer case fluid level. Flush and replace Power Steering Fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
SCHEDULE “A” 427 M Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Prop Shaft fitting. Rotate tires. Drain and refill transfer case fluid. Flush and replace engine coolant, if not done at 60 mos. Lubricate tie rod end links. Inspect brake linings. Inspect auto tension drive belt and replace if required. Replace ignition cables. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV Valve, replace as necessary.
M A I N T E N A N C E S C H E D U L E S 8 428 SCHEDULE “A” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. **This maintenance is recommend, but not required. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430 ▫ Prepare For The Appointment . . . . . . . . . . . . 430 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 430 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 430 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 430 䡵 Warranty Information . . . . . . . . . . . . . . . . . . . . 433 䡵 Mopar威 Parts . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 431 Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s dealers have the facilities, factory-trained technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner.
IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center.
IF YOU NEED CONSUMER ASSISTANCE 433 The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE U.S.
IF YOU NEED CONSUMER ASSISTANCE 435 MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE 437 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.
INDEX 10
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . 309,335 Air Cleaner, Engine (Engine Air Cleaner Filter) . 361,385 Air Conditioner Maintenance . . . . . . . . . . . . . . . 365 Air Conditioning Refrigerant . . . . . . . . . . . . . 365,366 Air Conditioning System . . . . . . . . . . . . . . . . 203,365 Air Conditioning System, Zone Control . . . . . . . . 207 Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . 296,304 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 441 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 Brake System . . . . . . . . . . . . . . . . . . . . . . . . 283,376 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 Disc Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . 376 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 376 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 Warning Light . .
INDEX Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 200 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377 Clutch Linkage Maintenance . . . . . . . . . . . . . . . . 378 Compact Disc Maintenance . . . . . . . . . . . . . . . . . 199 Compact Disc Player . . . . . . . . . . . . . . . . . . 172,179 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 299 Compass . . . . . . . . . .
INDEX 443 Disc Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376 Disposal Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Door Ajar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 130 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360 Driving Off-Pavement . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Ethylene Glycol Antifreeze . . . . . . . . . . . . . . . . . 374 Exhaust Gas Caution . . . . . . . . . . . . . . 72,150,313,371 Exhaust System . . . . . . . . . . . . . . . . . . . . 72,370,371 Exterior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 111 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . 361,385 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 362 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 360,407 Engine Oil Disposal . . .
INDEX 445 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 307 Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Coolant Temperature . . . . . . . . . . . . . . . . . . . . 160 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 159 Tachometer . . . .
INDEX Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . 304 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 84 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 156,157 Instrument Panel and Controls . . . . . . . . . . . . . . 155 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 392 Interior Appearance Care . . . . . . . . . . . . . . . . . . 391 Intermittent Wipers . . . . . . . . . .
INDEX 447 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 334 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 High Beam . . . . . . . . . . . . . . . . . . . . . . . . 115,158 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 158 High Beam/Low Beam Select . . . . . . . . . . . . . . 115 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 157 Intensity Control . . . . . . . . . . . . . . . . . . . . . . . 110 Interior . . . . . . . . . . . . . . . . . . . . .
INDEX Schedule ⬙B⬙ . . . . . . . . . . . . . . . . . . . . . . . . . . 413 Malfunction Indicator Light . . . . . . . . . . . . . . . . 354 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 436 Manual Transmission . . . . . . . . . . . . . . . . . . 275,379 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . 379 Lubricant Selection . . . . . . . . . . . . . . . . . . 379,408 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Automatic Dimming . . . . . .
INDEX 449 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . 359,406 Onboard Diagnostic System . . . . . . . . . . . . . . . . 353 Opener, Garage Door . . . . . . . . . . . . . . . . . . . . . 130 Operating Precautions . . . . . . . . . . . . . . . . . . . . 353 Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . 86 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 Overdrive OFF Switch . . . . .
INDEX Radiator Cap (Coolant Pressure Cap) . . . . . . . 372,375 Radio Operation . . . . . . . . . . . . . . . . . . . . . . 166,183 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . 197 Radio (Sound Systems) . . . . . . . . . . . 166,172,183,189 Ramp Travel Index . . . . . . . . . . . . . . . . . . . . . . . 225 Rear Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378 Rear Wheel Bearings . . . . . . . . . . . . . . . . . . . . . 383 Reclining Front Seats . . . . . . . . . . .
INDEX 451 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Child . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Stabilizer Bars, Electronic Disconnecting . . . . . . . . 81 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 Automatic Transmission . . . . . . . . . . . . . . . . . 268 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 268 Manual Transmission . .
INDEX 453 Inflation Pressures . . . . . . . . . . . . . . . . . . . . . 296 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 Load Capacity . . . . . . . . . . . . . . . . . . . . . 291,292 Off-Road . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 302 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 Safety . . . . . . . .
INDEX Maintenance . . . . . . . . . . . . . . . . . . . . . . . 379,380 Manual . . . . . . . . . . . . . . . . . . . . . . . . 267,275,379 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . 270,276 Transmitter, Garage Door Opener . . . . . . . . . . . . 130 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 302 Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . 163,164 Turn Signals . . . . . . . . . . .
INDEX 455 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Rear Sliding . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Windshield Defroster . . . . . . . . . . . . . . . . . . 202,205 Windshield Washers . . . . . . . . . . . . . . . . 115,117,369 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115,369 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 369 Windshield Wipers . . . .
