SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Van Conversions/Campers . . . . . . . . . . . . . . . . . 5 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Modifications / Alterations . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all subjects. WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 Power Wagon: Things To Know Before Starting Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Instrument Panel And Controls . . . . . . . . . . . .12 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Emergencies . . . . . . . . . . . . . . . . . . . . . . . . . .12 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Remote Keyless Entry — If Equipped . . . . . . . . .22 ▫ Sliding Rear Window—If Equipped . . . . . . . . .32 ▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . .23 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .32 ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .24 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .33 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .25 ▫ Lap/Shoulder Belts .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbag . . . . . . . . . . . .45 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .56 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .57 䡵 Engine Break-In Recommendations . . . . . . . . . . .69 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Transporting Passengers . . . . . . . . . . . . . . . . .70 11 ▫ Lock Your Vehicle . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER WAGON: THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Your Power Wagon is a specialty vehicle, equipped with several features not available on other production trucks. It is very important that you read the following sections of the owner’s manual before operation. Features (See page 80 for more information.) Instrument Panel and Controls (See page 166 for more information.) Operation (See page 231 for more information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for a maximum of 2 seconds after the initial key ON. After six unsuccessful attempts at starting, the system will shut down until the correct key is used.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. ⬙Security Light⬙ will begin to flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference that may be received including interference that may cause undesired operation. depress and hold the release button located between the ignition switch and the instrument panel. Turn the ignition key to LOCK and remove the key. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. The key can be inserted or withdrawn only in the LOCK position. Push in on the key in the ignition lock cylinder to rotate to the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR KEY The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn. To lock the doors, insert the key and turn. 17 WARNING! For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock plunger up or down.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks — If Equipped NOTE: Vehicles equipped with remote keyless entry do not have a passenger side door lock cylinder. Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph. This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Feature Programming Customer Programming sequence to enable or disable the Auto Unlock Feature: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chimes that may be confusing during this programming procedure). 3. Insert the key into the ignition. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the childprotection door lock system. the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! REMOTE KEYLESS ENTRY — IF EQUIPPED Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. 5. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 9. Test the park lamp flash feature by pressing the LOCK button on the key fob with the ignition in the OFF position or the key removed. 3. Place the key into the ignition. 10. To reactivate this feature, repeat the above steps. 4. Turn the ignition to the ON position ( Do not start the engine ). 11.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE door locks and remote keyless entry systems will function normally. Panic mode will not disarm the security system on vehicles so equipped. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). Programming Additional Transmitters Vehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. A single chime will be heard. The chime indicates that the fob has been recognized. 10. Within 4 seconds of hearing the chime, press and release any button on the fob being programmed. 11. A single chime will be heard. The chime indicates that the fob has been programmed. 12. Repeat steps 8 to 11 for a total of 4 fobs. 13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode. 14.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. Transmitter Battery Service 1. With transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the batteries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly. For an additional 15 minutes only the headlights and security telltale will flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. WINDOWS Power Windows—If Equipped The Security system will also disarm, if the vehicle is started with a programmed Sentry Key. If an unprogrammed Sentry Key is used to start a vehicle, the engine will run for 2 seconds and then the security alarm will be initiated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 models. The windows will operate only when the ignition switch is turned to the ON or ACC (Accessory) position. WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button. To enable the window controls, press the window control button again. Window Lockout Switch Sliding Rear Window—If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and, if so equipped, window bags for the driver and passengers seated next to a window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the Quad Cab front center seating position have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Removing Slack From Belt WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 37 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! Detaching Buckle with Key 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate In Use Position
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that serves you best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Restraint (ALR) Mode – If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is available on all passenger seating positions with a combination lap/shoulder belt. When To Use The Automatic Locking Mode Anytime a child safety seat is installed in a passenger seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal injuries is greater. Wear a lap belt low and snug.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These airbags are certified to the new Federal regulations that allow less forceful deployments. WARNING! • Do not put anything on or around the airbag covers or attempt • • This vehicle may also be equipped with window bags to protect the driver and passengers in the first and second row sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with the seatbelts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Window Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Window Bags Above the Side Windows. • Airbag Control Module (shared with the front airbag system) • Side impact sensors • Interconnecting Wiring How The Airbag System Works • The airbag control module determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIR BAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Airbag On/Off Switch – (Standard Cab Vehicles Only) 51 because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, • is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child, • has a medical condition which ma
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! To Turn On the Passenger Airbag (Standard Cab Vehicles Only) Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key from the switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to require the side airbags to inflate. The window airbag control module will not detect roll over, front or rear collisions. The airbag control module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the ⬙START⬙ or ⬙RUN⬙ positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag Systems WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to inflate for your protection. Promptly check fuse numbers 52 and 53 in the fuse and relay center. See your dealer if the fuse is good. Event Data Recorder (EDR) In the event of an airbag deployment, your vehicle is designed to record up to 2-seconds of specific vehicle data parameters (see list below) in an event data recorder prior to the moment of airbag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler Corporation to any third party except when: 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat, or in the front seat if the passenger’s front airbag is Off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then pull on the belt until it is all removed from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Refer to the ⬙Automatic Locking Retractors (ALR) Mode⬙ earlier in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Multiple Child Restraint Installation Sequence (Quad Cab Rear Seats) 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the metal ring. 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up” position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Quad Cab Tether Strap Mounting
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. • Limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lock Your Vehicle Always remove the keys from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving articles of value exposed. Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a potentially toxic gas that by itself is colorless and odorless.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Latches Check for positive closing, latching and locking. 73 Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Power Wagon Features . . . . . . . . . . . . . . . . . . . .80 ▫ Skid Plates And Underbody Protection . . . . . . .82 ▫ Locking Front And Rear Differentials . . . . . . . .80 ▫ Wheel Flares . . . . . . . . . . . . . . . . . . . . . . . . . .82 ▫ 4.56:1 Gears . . . . . . . . . . . . . . . . . . . . . . . . . .80 ▫ Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 ▫ Electronically Disconnecting Stabilizer/Sway Bar . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .86 ▫ 40-20-40 Front Seat . . . . . . . . . . . . . . . . . . . . 114 ▫ Electronic Power Mirrors — If Equipped . . . . . .87 ▫ Reclining Seats . . . . . . . . . . . . . . . . . . . . . . . 115 ▫ Electric Rear Window Defroster And Heated Sideview Mirrors — If Equipped . . . . . . . . . . .88 ▫ Adjustable Head Restraints . . . . . . . . . . . . . . 115 ▫ Trailer Towing Mirrors — If Equipped . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Daytime Running Lights (Canada Only And Fleet Vehicles) . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 124 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 124 ▫ Cargo Light — If Equipped . . . . . . . . . . . . . . 125 䡵 Multifunction Control Lever . . . . . . . . . . . . . . . 125 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ Passing Light . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Step Button . . . . . . . . . . . . . . . . . . . . . . . . . 136 ▫ Using Homelink . . . . . . . . . . . . . . . . . . . . . . 147 ▫ Average Fuel Economy (AVG ECO) . . . . . . . . 137 ▫ Erasing Homelink Buttons . . . . . . . . . . . . . . . 147 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . 137 ▫ Reprogramming a Single Homelink Button . . . 147 ▫ Trip Odometer (ODO) . . . . . . . . . . . . . . . . . . 138 ▫ Security . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . 151 ▫ Center Storage Compartment — If Equipped . . 154 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . . 151 ▫ Storage And Seats — If Equipped . . . . . . . . . . 155 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . . 151 䡵 Fold Flat Load Floor — If Equipped . . . . . . . . . 156 䡵 Cigar Lighter And Ash Receiver . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER WAGON FEATURES Locking Front and Rear Differentials Most 4WD trucks are equipped with open differentials front and rear. This design is used because it allows each wheel to turn independently helping to eliminate binding when cornering. A disadvantage of using an open differential is when one or more wheels lose traction; all of the power is directed to those wheels resulting in a loss of momentum.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electronically Disconnecting Stabilizer/Sway Bar Stabilizer bars are used to help distribute load force from one side of the vehicle to the other. This helps to reduce body roll and create a smoother ride during on-road driving. However, this becomes a disadvantage when the vehicle is driven off-road when a higher level of suspension articulation is needed. By disconnecting the stabilizer bars, each wheel can now reach its maximum range of movement.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High-Pressure Monotube Shocks/New Front and Rear Springs The new variable-rate shocks and revised springs help to create a suitable on-road ride without compromising off-road competency. The shocks are designed to provide improved stability, durability, and suspension articulation. Off-Road Tires These tires are specifically designed for extreme off-road use, while also maintaining quite on-road operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Wheels Stylish forged aluminum 17⬙ wheels give the Power Wagon a powerful stance. Forging a wheel from aluminum produces a stronger, lighter weight wheel than machining or casting the wheel out of the same material. • Steering Dampener Skid Plate - protects the steering dampener from impingement damage. Standard package features: • Electronically Disconnecting Stabilizer/Sway Bar - improves mobility and articulation by disconnecting the Stabilizer/Sway Bar.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Off-Road Tuned Suspension And Shocks - improves mobility, ground clearance and ride comfort. • Heavy Duty Thermally Protected and Sealed Electric Winch With Roller Fairlead - Useful for work and vehicle recovery. • 17 Inch Forged Aluminum Wheels With 33 Inch Tires - improves traction and differential ground clearance. Mopar Options: • Rock Rails - protects the door sills from impingement damage and provides a vehicle jacking point.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). 85 Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Electronic Power Mirrors — If Equipped 3 Power Mirror Switches Power Mirror Movement The controls for the power mirrors are located on the driver’s door trim panel. Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the rear window defroster or the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 3 Blindspot Mirror Trailer Towing Position
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial” ѧ “248-555-1212⬙). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE with the system at a time. The system is available in English, Spanish, or French languages (as equipped). The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the ⬙Operation⬙ section. 91 The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation Voice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands are required after most UConnect™ system prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙Ready⬙ prompt or another prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Cancel Command At any prompt, after the voice on beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. • www.jeep.com/uconnect Pair (Link) UConnect™ System to a Cellular Phone To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone (refer to ⬙Introduction⬙ section to learn about the phone type).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE your cellular phone’s user manual (Bluetooth section) for instructions on how to complete this step. • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • The UConnect™ system will confirm the phone number and then dial. The number will appear in the display of certain radios. • The UConnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Call by Saying a Name Add Names to Your UConnect™ Phonebook • Press the “Phone” button to begin. NOTE: Adding names to phonebook is recommended when vehicle is not in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g.: ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later using the ⬙Phonebook Edit⬙ feature. Delete Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook List Names.⬙ • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ⬙Voice Recognition’ button during the playing of the desired name and say ⬙Call⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the current call on hold and answer the incoming call. NOTE: The UConnect™ system compatible phones in market today do not support rejecting an incoming call when another call is in progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Conference Call When two calls are in progress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Redial Three-Way Calling To initiate three-way calling, press the ’Voice Recognition’ button while a call is in progress and make a second phone call as described in section ⬙Making a Second Call while Current Call in Progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect™ system will instruct the paired cellular phone to call the emergency number. This feature is only supported in the USA.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging To learn how to page, refer to section ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to section ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ system will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 • Press the ’Voice Recognition’ button. Advanced Phone Connectivity • After the ⬙Ready⬙ prompt and the following beep, say ⬙Mute.⬙ Transfer Call to and from Cellular Phone The UConnect™ system allows on going calls to be transferred to your cellular phone to the UConnect™ system without terminating the call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone.⬙ • After the “Ready” prompt and the following beep, say “Setup Phone pairing”. • When prompted, say ⬙List Phones⬙. • The UConnect™ system will play the phone names of all paired cellular phones in order from the highest to the lowest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. 107 Things You Should Know About Your UConnect™ System • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ Voice Recognition (VR) • At the next prompt, say ⬙Delete.⬙ • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • The phone names (along with priority numbers) will be played.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some. • When navigating through an automated system, such as, voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙send.⬙ • Storing names in phonebook when vehicle is not in motion is recommended.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance, such as, audio clarity, echo. and loudness to a large degree, rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth Communication Link Cellular phones have been found to occasionally lose connection to the UConnect™ system. When this happens, the connection can generally be re-established by switching the phone off/on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40-20-40 Front Seat Each outboard seat is independently adjustable forward or backward and is equipped with a back recliner. The manual seat adjustment handle is found at the front edge of each seat cushion. Pull up on the handle and slide the seat to get the most comfortable position. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle to release the seat back and adjust for comfort. 115 WARNING! You can be seriously, even fatally injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To lower the head restraint, push in the button and then push down on the head restraint. Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. 3 Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat movement. The four-way switch in the center can be moved forward or backwards to get the most comfortable position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls. Tilt Adjustment Heated Seat Switches Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain High heat level, then press the switch again to obtain Low heat level.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the switch a third time will turn the heated seats OFF. If you do not purposefully turn the switch OFF, the seat heating level will automatically change to the next lower level, or OFF. The High heat level operates for 45 minutes (approximate), the Low heat level operates for 60 minutes (approximate). The seat heat will also turn OFF when the ignition is turned OFF. Both of the indicators ON identifies High heat level.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE released you must reach into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. Secondary Latch WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS 121 Interior Lights 3 Headlight Switch Location Dimmer Control Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Headlamp Delay To aid in your exit, your vehicle is equipped with a headlamp delay that will leave the headlamps on for 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. Headlamp delay can be cancelled by either turning the headlamp switch ON then OFF or by turning the ignition ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Lights-on Reminder If the headlights, parking lights, or cargo lights are left on, after the ignition is turned off, a chime will sound when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO Light — If Equipped 125 MULTIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering column. Turn Signals Move the lever up or down to signal a right-hand or left-hand turn. Cargo Light Switch The cargo lights are turned on by pressing on the CARGO button. The interior lights will also turn on when the cargo lights are on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can signal a lane change by moving the lever partially up or down. Turn Signal Lever Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam. 127 Windshield Wipers 3 Windshield Wiper / Washer Switch High Beam / Low Beam The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the LO continual speed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. 129 3 TILT STEERING COLUMN To tilt the column, pull rearward on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever forward to lock the column firmly in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator operation at speeds greater than (refer to the table below for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CANCEL button will deactivate speed control without erasing the memory. Pushing the ON/OFF button to the OFF position or turning off the ignition erases the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed increases so that tapping the button three times will increase speed by three increments. Tapping the DECEL button once will result in a speed decrease (refer to the table below for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. If the vehicle speed drops below (refer to the table below for the speed for your specific engine), the speed control will automatically disengage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: • Universal Garage Door Opener — If Equipped Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE WITH COMPASS/TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: 135 This overhead console allows you to choose between a compass/temperature display and one of four trip conditions being monitored. US/M Button • Courtesy Lights 3 • Compass/Temperature Mini-Trip Computer (CMTC) Use this button to change the display from U.S. to metric measurement units.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE RESET Button Global Reset If the RESET button is pressed twice within 2 seconds while in any of the 3 resettable displays (AVG ECO, ODO, ET), the Global Reset will reset all 3 displays. Step Button Use this button to reset the following displays: Average Fuel Economy (AVG ECO) Trip Odometer (ODO) Elapsed time (ET) Use this button to choose or cycle through the four trip conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. Average fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled. When the fuel economy is reset, the display will momentarily blank. Then, the history information will be erased, and the averaging will continue from where it was before the reset.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Trip Odometer (ODO) This display shows the distance traveled since the last reset. Resetting of this screen will cause the trip odometer to change to Zero. C/T Button Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. Resetting the Elapsed Time will cause the display to change to Zero.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the CAL symbol will be displayed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The default for the compass variance is zone 8. To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause serious injury or death. WARNING! Outer HomeLink buttons Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held transmitter buttons. Do not release the buttons until step 4 has been completed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button. (The name and color of the button may vary by manufacturer.) NOTE: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.) Proceed with ⬙Programming⬙ step four to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security If you sell your vehicle, be sure to erase the frequencies. To erase all of the previously trained frequencies, hold down both outside buttons until the green light begins to flash. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called Express Close. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE As a child safety precaution, the lighter only operates with the ignition switch ON. It heats when pushed in and pops out automatically when ready for use. To preserve the heating element, do not hold the lighter in the heating position. 153 CUPHOLDERS Front Instrument Panel Cupholders To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholder — Quad Cab — If Equipped Quad Cab vehicles may be equipped with a rear cupholder that consists of two cupwells for rear passenger convenience. STORAGE Center Storage Compartment — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. • In an accident, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.5 kg). These items could be thrown about endangering occupants of the vehicle. Items stored should not exceed a total of 10 lbs (4.5 kg).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLD FLAT LOAD FLOOR — IF EQUIPPED Fold Flat Load Floor — If Equipped Quad Cab models with a 60/40 rear seat, may be equipped with a folding load floor. WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 3 Unfolding The Load Floor 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Load Floor In Open Position 3. Reverse the procedure to store the load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. WARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury. Load Floor Securing Straps 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopar威 toolbox brackets available from your dealer. PICKUP BOX You can carry wide building materials (sheets of plywood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Care should always be exercised when operating a vehicle with unrestrained cargo. Vehicle speeds may need to be reduced. Severe turns or rough roads may cause shifting or bouncing of the cargo that may result in vehicle damage. If wide building materials are to be frequently carried, the installation of a support is recommended. This will restrain the cargo and transfer the load to the pickup box floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE EASY-OFF TAILGATE The tailgate can be removed quickly. Tailgate removal is sometimes required for pickup box loading. To remove the tailgate unlatch the tailgate and remove the support cables by releasing the lock tang from the pivot, then rotate and pull away from the box. Once the cables are free, move to the right side of the tailgate hinge bracket. Raise the right side of the tailgate until the right side pivot clears the hanger bracket.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 166 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 167 ▫ Operating Instructions - Hands Free Phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 182 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . . 176 䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Video Capabilities . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operation Instructions - (CD Mode For MP3 Audio Play) . . . . . . . . . . . . . . . . . . . . . . . . . 192 ▫ Load/Eject Button (CD Mode For MP3 Play) . . 192 䡵 Sales Code RAK – AM/FM/Cassette/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, Video, MP3, And WMA Capabilities . . . . 195 ▫ Operating Instructions - Radio Mode . . . . . . . 195 ▫ Operating Instructions — Tape Player . . . . . . . 199 ▫ Seek Button . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Satellite Radio (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . 209 䡵 Remote Sound System Controls — If Equipped . . 210 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 210 ▫ Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . 211 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 211 䡵 Cassette Tape And Player Maintenance . . . . . . . 211 䡵 Compact Disc Maintenance . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 167 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Check Gages This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gages indicate a reading either too high or too low. Examine the gages carefully, and follow the instructions above for each indicated problem. NOTE: When the ignition switch is turned to OFF, the Fuel Gage, Voltmeter, Oil Pressure and Engine Coolant Temperature gages may not show accurate readings.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 5. Airbag Indicator Light The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned on. If the light stays on, flickers or comes on while driving, have the airbag system checked by an authorized dealer. 6. High Beam Indicator This indicator shows that headlights are on high beam. 7.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 10. Transfer Case Position (See page 287 for more information.) 11. TOW HAUL The TOW HAUL button is located at the end of the gear shift lever. This light will illuminate when the TOW HAUL OD/OFF button is pushed once. (See page 283 for more information.) 12.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not leave your vehicle unattended with the engine running as you would not be able to react to the temperature indicator if the engine overheats. NOTE: Engine idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling. NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 14.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The odometer/trip odometer Vacuum Fluorescent Display will also may display GASCAP, which indicates that your gas cap is possibly loose or damaged. (See page 320 for more information.) The Vacuum Fluorescent Display will also display NOFUSE, which indicates that the IOD fuse is removed from the Integrated Power Module. (See page 405 for more information.) NOTE: There is also an engine hour function.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. 18. Brake System Warning Light This light illuminates when the ignition key is turned to the ON position and remains on for a few seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL that the anti-lock portion of the brake system is not functioning and that service is required. See your authorized dealer immediately. The ABS light could also illuminate during loss of traction and remain illuminated until the brake pedal is pressed. 20. Cargo Light The Cargo Lamp light will illuminate when the Cargo Lamp is activated by pressing the Cargo Light Button on the headlight switch. 21.
UNDERSTANDING YOUR INSTRUMENT PANEL 24. Low Washer Fluid Light This light comes on when the washer fluid level falls below approximately 1/4 full. The light will remain on until fluid is added and ignition switch is cycled. 25. Transmission Oil Temperature Warning Light (Automatic Transmissions Only) This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 29. Door Ajar The Door Ajar light will illuminate when any door is opened. When the ignition is ON the Door Ajar light will stay illuminated until the open door is closed. When the ignition is OFF the Door Ajar light will stay illuminated until the open door is closed or the battery saver feature automatically turns the light off.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL HANDS FREE PHONE CAPABILITY 177 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player or Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down.The radio will remained tuned to the new station until you make another selection.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 NOTE: • You may insert or eject a disc with the radio or ignition switch OFF. SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player and the display will show the time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: RND Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band. To stop the search, press SCAN a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information. Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL Top 40 Country Oldies Soft Nostalgia Jazz Classical Rhythm and Blues Soft Rhythm and Blues Foreign Language Religious Music Religious Talk Personality Public College Unassigned Weather Top_40 Country Oldies Soft Nostalgia Jazz Classical Rhythm_and_Blues Soft_R_&_B Foreign_Language Religious_Music Religious_Talk Personality Public College Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with t
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Note: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD MODE For CD Audio Play) Press the Scan button to scan through each track on the CD currently playing. LOAD/EJECT Button (CD Mode For CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙LOAD DISC⬙ insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (CD MODE For CD Audio Play) Press this button to change the display from a large CD playing time display and small clock time display to a large clock time display and small CD playing time display. RW/FF (CD MODE For CD Audio Play) Press FF (Fast Forward) once and the CD player will begin to fast forward until FF is pressed again or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported media (disc types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW. Supported medium formats (file systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 file formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL LOAD / EJECT - Eject Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJECT button to eject all discs in the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode For MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode For MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAK – AM/FM/CASSETTE/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, VIDEO, MP3, and WMA CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. 195 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (Radio Mode) Press and release the SEEK button to search for the next station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remained tuned to the new station until you make another selection. Holding the button and will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes.
UNDERSTANDING YOUR INSTRUMENT PANEL within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the left and the mechanical action of the player will gently pull the cassette into the play position.
UNDERSTANDING YOUR INSTRUMENT PANEL Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed again or the end of the tape is reached. At the end of the tape, the tape will play in the opposite direction. Rewind (RW) Press the RW button momentarily to reverse the tape direction. The tape will reverse until the button is pressed again or until the end of the tape is reached.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks and WMA. To turn off the Dolby Noise reduction System: Press Preset 1 after you insert the tape. The NR light in the display will go off when the Dolby System is off.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 5 seconds of the current selection. SCAN Button (CD MODE for CD Audio Play) Press the Scan button to scan through each track on the CD currently playing.
UNDERSTANDING YOUR INSTRUMENT PANEL radio, the radio will remain in CD mode and display ⬙INSERT DISC” for 2 minutes. After 2 minutes the radio will go to the previous tuner mode. The disc can be ejected with the radio and ignition OFF. TIME Button (CD MODE for CD Audio Play) Press this button to change the display from a large CD playing time display to a small CD playing time display.
UNDERSTANDING YOUR INSTRUMENT PANEL Buttons 1 - 6 (CD MODE for CD Audio Play) Selects disc positions 1 - 6 for Play/Load/Eject. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 and WMA Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will show ⬙LOADING DISC⬙ when the disc is loading. LOAD / EJT - Eject Press the LOAD/ EJT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM 209 Satellite Navigation Radio with CD Player with MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability.
UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a button in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The center button of the right hand control will allow you to change the mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection. If you press the switch up or down twice it plays the second selection, three times, it will play the third, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. 213 CLIMATE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL Heater Only — Fleet Vehicles NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots. Panel Outside air flows through the outlets located in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Mix Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield, and the demister outlets located at the edge of each side of the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning and Heating — If Equipped outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots. Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Recirculation Modes (Panel or Bi-Level ) Select the recirculation modes when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left position. Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob.
UNDERSTANDING YOUR INSTRUMENT PANEL Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature. These features also turn off after activation, when 15 minutes have elapsed.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning and Heating Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be directed through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots and give an even blend of both modes. Panel Outside air flows through the outlets located in the instrument panel. These outlets can be adjusted to direct the airflow. Bi-Level Air flows through the outlets located in the instrument panel and those located on the floor.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed. This dehumidifies the air to help dry the windshield. Dual Zone Temperature Control Blower Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire.
UNDERSTANDING YOUR INSTRUMENT PANEL Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes. Once the hot air has been expelled, close the windows and press the Recirculation push-button.
UNDERSTANDING YOUR INSTRUMENT PANEL Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 Axle Locker System . . . . . . . . . . . . . . . . . . . . . 231 ▫ Airing Down For Off-Road Driving . . . . . . . . 250 䡵 Stabilizer/Sway Bar System . . . . . . . . . . . . . . . 234 ▫ Vehicle Recovery . . . . . . . . . . . . . . . . . . . . . . 251 䡵 Power Wagon – Safe Off-Road Driving . . . . . . . 235 ▫ After Driving Off-Road . . . . . . . . . . . . . . . . . 255 ▫ Off-Road Driving Tips And Vehicle Characteristics . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Ignition/Starter Switch . . . . . . . . . . . . . . . . . . . 275 䡵 Transmission Shifting . . . . . . . . . . . . . . . . . . . . 280 ▫ Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ Automatic Transmission With Overdrive . . . . . 280 ▫ Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ Manual Transmission — 6-Speed . . . . . . . . . . 285 ▫ On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Four-Wheel Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 294 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 296 䡵 Multi Displacement System (MDS) - 5.7L Engine Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 296 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 296 ▫ Tire Identification Number (TIN) . . . . . . . . . .
STARTING AND OPERATING ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 318 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . . 331 ▫ Sulfur In Gasoline . . . . . . . . . . . . . . . . . . . . . 319 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 332 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 319 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 337 ▫ Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING Axle Locker System Dodge Power Wagons are equipped with electronically locking front and rear axles. Locking the axles provides greater traction in severe low traction conditions or in rock climbing environments where one wheel is likely to not be in contact with the ground. 231 CAUTION! Do not try to lock the rear axle if the vehicle is stuck and the tires are spinning. You can damage drivetrain components.
STARTING AND OPERATING rear axles are unlocked. In the REAR LOCK position, the rear axle is locked. In the FRONT/REAR position, the front and rear axles are locked. NOTE: Even when the axles are in the AXLE UNLOCK position, the limited slip differential in the rear axle still provides torque biasing capability for moderate low traction environments. During the command to lock the axle, the indicator light will flash until the axle is locked.
STARTING AND OPERATING 233 NOTE: Left to right wheel speed difference may be necessary to allow the axle to fully lock. If the indicator light is flashing after placing the switch in the REAR LOCK or FRONT/REAR position, drive the vehicle in a turn or on loose gravel to expedite the locking action. NOTE: The rear axle must be locked before the front axle will lock. WARNING! NOTE: The axle lockers could be torque locked due to side to side loads on the axle.
STARTING AND OPERATING Stabilizer/Sway Bar System Power Wagon vehicles are equipped with an electronic disconnecting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. The switch has two positions, on-road and off-road. The system is normally in on-road mode, indicated by a solid green light. The stabilizer/sway bar should remain in on-road mode during normal driving conditions.
STARTING AND OPERATING To disconnect the stabilizer/sway bar, shift to either 4HI or 4LO as shown in Four Wheel Drive Operation and press the top of the stabilizer/sway bar button to obtain the off-road position. The amber indicator light will flash until the stabilizer/sway bar has been fully disconnected. (See page 287 for more information.) NOTE: The stabilizer/sway bar may be torque locked due to left and right suspension height differences.
STARTING AND OPERATING vehicle (ORV) trails or recreation areas. You should always tread lightly and only use established roads, trails or ORV recreational areas. The National Forest Service, Bureau of Land Management or local Department of Natural Resources are a wealth of information and usually have maps with marked trails.
STARTING AND OPERATING 237 5 Angles A, B, C, and D
STARTING AND OPERATING Water Fording Front and Rear (Shown) Differential Height E Water Fording Characteristics Water fording characteristic is the vehicle’s ability to cross a body of still water, where the powertrain and drivetrain are safe from water ingestion.
STARTING AND OPERATING CAUTION! The door sill height is 25 inches. Water may intrude into the interior of the vehicle at greater depths. Simultaneous Brake And Throttle Operation Many off-road driving conditions require the simultaneous use of the brake and throttle (two footed driving). When climbing rocks, logs, or other stepped objects, using light brake pressure with light throttle will keep the vehicle from jerking or lurching.
STARTING AND OPERATING WARNING! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When To Use Low Range When driving off-road, shift into 4L (Low range) for additional traction or to improve handling and control on slippery or difficult terrain. Due to the lower gearing, low range will allow the engine to operate in a higher power range. This will allow you to idle over obstacles and down hills, with improved control and less effort.
STARTING AND OPERATING CAUTION! On icy or slippery roads, do not downshift at high engine rpm’s or vehicle speeds because engine braking may cause skidding and loss of control. • Mud – Deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use 4L (low range) with a gear low enough to maintain your momentum without shifting.
STARTING AND OPERATING CAUTION! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneuvers. Crossing Obstacles (Rocks And Other High Points) While driving off road, you will encounter many types of terrain. These varying types of terrain bring different types of obstacles.
STARTING AND OPERATING Crossing Large Rocks When approaching large rocks, choose a path which ensures you drive over the largest of them with your tires. This will lift your undercarriage over the obstacle. The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse. Always look ahead and make every effort to cross the large rocks with your tires. CAUTION! Never attempt to straddle a rock that is large enough to strike your axles or undercarriage.
STARTING AND OPERATING WARNING! CAUTION! There is an increased risk of roll over when crossing an obstacle, at any angle, with steep sides. Do not attempted to cross a log with a greater diameter than the running ground clearance or the vehicle will become high centered. Crossing Logs To cross a log, approach it at a slight angle (approximately 10 to 15 degrees). This allows one front tire to be on top of the log while the other just starts to climb the log.
STARTING AND OPERATING CAUTION! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill Climbing Hill climbing requires good judgment and a good understanding of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and should not be attempted. You should always feel confident with the vehicle and your abilities. You should always climb hills straight up and down. Never attempt to climb a hill on an angle.
STARTING AND OPERATING a 1⁄4 turn quickly back and forth. This will provide a fresh ⬙bite⬙ into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in reverse and back straight down the grade using engine resistance along with the vehicle brakes. WARNING! Never attempt to climb a hill at an angle or turn around on a steep grade. Driving across an incline increases the risk of a roll over, which may result in severe injury.
STARTING AND OPERATING more weight on the down hill wheels, which increases the possibilities of a down hill slide or roll over. Make sure the surface has good traction with firm and stable soils. If possible transverse the incline at an angle heading slightly up or down. WARNING! Driving across an incline increases the risk of a roll over, which may result in severe injury.
STARTING AND OPERATING Driving Through Water Extreme care should be taken crossing any type of water. Water crossings should be avoided if possible and only be attempted when necessary, in a safe responsible manner. You should only drive through areas which are designated and approved. You should tread lightly and avoid damage to the environment. You should know your vehicles abilities and be able to recover it if something goes wrong.
STARTING AND OPERATING muddy waters, check for hidden obstacles. Make sure you will not be intruding on any wildlife and you can recover the vehicle if necessary. The key to a safe crossing is the water depth, current and bottom conditions. On soft bottoms the vehicle will sink in, effectively increasing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross.
STARTING AND OPERATING downstream out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed determine the speed of the current, the water’s depth, approach angle, bottom condition and if there are any obstacles, then cross at an angle heading slightly upstream using the low and slow technique. WARNING! Never drive through fast moving deep water. It can push your vehicle downstream, sweeping it out of control.
STARTING AND OPERATING CAUTION! Reduced tire pressure increases the risk of tire damage and may cause tire unseating with total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, drive at slower speeds and avoid sharp turns or abrupt maneuvers. Vehicle Recovery If you drive off-road, you may encounter a situation where you will need to recover your vehicle. Vehicle recovery should always be given consideration before attempting a questionable obstacle.
STARTING AND OPERATING CAUTION! Pulling the vehicle off an obstacle, without first clearing the object, may result in additional underbody damage. • Rock Cycling Your Vehicle – Rock cycling your vehicle is one of the easiest, fastest and most commonly used methods. This simply involves shifting your vehicle from drive to reverse, while applying throttle after each shift. During this process, for additional traction, try turning your steering wheel quickly back and forth no more than a 1⁄4 turn.
STARTING AND OPERATING the two drivers. Good communication and line of sight are required for a safe recovery. First connect the tow strap to the correct attachment points on both vehicles. There should be a least 20 to 30 feet between the vehicles to allow for a safe recovery. If necessary join two tow straps together using a 1 1⁄2 inch hard wood dowel. This will keep the straps from becoming knotted and is safer than using a clevis pin if the strap breaks.
STARTING AND OPERATING • Winching (see the section on “Winch Operation” for additional information on the Power Wagon’s winch) – Winching is most commonly used in the following situations: there is no support vehicle available, a high controlled force is required to recover the vehicle, there is a high risk of environmental or vehicle damage, or where nothing else seemed to work. A winch can deliver a high pulling force with a great deal of control.
STARTING AND OPERATING WARNING! Winch cables are under high tension when in use and can become a projectile if they fail. Never stand over or straddle the winch cable. Never jerk or overload the winch cable. Never stand in front of the vehicle while winching. Failure to follow these instructions can result in serious or fatal injury. After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving.
STARTING AND OPERATING WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. Failure to do so may result is serious injury. high forces and should be used with care. Do not operate the winch without reading and understanding the complete winch owner’s manual.
STARTING AND OPERATING 3. Apply at least 500 lbs. of tension to the rope while winding the rope in. Always use care to ensure the rope does not pile up on one side of the drum and is neatly wound onto the drum. CAUTION! Wire rope must spool on the winch drum in the direction indicated on the drum rotation decal on the winch. Low Voltage Interrupt Your winch is equipped with a device that will interrupt winch function if the vehicle charging system voltage drops to a low level.
STARTING AND OPERATING UNDERSTANDING THE FEATURES OF YOUR WINCH Winch Components
STARTING AND OPERATING 1. Motor: The winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote Socket: The remote socket allows the remote control to be attached to the control pack to allow the winch to function. 3. Winch Drum w/ Integral Brake: The winch drum allows the wire rope to be stored on the winch and transmits force to the wire rope.
STARTING AND OPERATING WINCH ACCESSORIES The following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: Wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is extremely important to wear protective gloves while operating the winch or handling the wire rope. Avoid loose fitting clothes or anything that could become entangled in the wire rope and other moving parts.
STARTING AND OPERATING Clevis/D-Shackles: The D-Shackle is a safe means of connecting the looped ends of cables, straps and snatch blocks. The shackle’s pin is threaded to allow easy removal. Tree Trunk Protector: Typically made of tough, highquality nylon, it provides the operator an attachment point for the winch rope to a wide variety of anchor points and objects, as well as protect living trees.
STARTING AND OPERATING General Information Practice using your winch before you get stuck. Some key points to remember when using your winch are: 1. Always take your time to assess the situation and plan your pull carefully. Vehicle Recovery Using the Winch: CAUTION! • Always Know Your Winch: Take time to fully read 2. Always take your time when using a winch. 3. Use the right equipment for the situation. 4.
STARTING AND OPERATING CAUTION! Be careful not to pull the Winch Cable Collar through the rollers. Watch and listen to Winch for proper snugness. 263 1. Inspect the winch, winch mount, and wire rope for damage. Do not use the winch if the mount is loose or rope shows excessive wear or damage. 2. Put on gloves.
STARTING AND OPERATING 3. Disengage clutch to allow free spooling of the winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserves battery power. 4. Free the winch hook and attach hook strap. Free the winch hook from its anchor point. Attach hook strap to the hook (if not attached).
STARTING AND OPERATING 5. Pull wire to anchor point. Pull out enough wire rope to reach your anchor point. Be sure to keep a certain amount of tension on the wire as it can become twisted and over-wrap when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work. 265 6. Secure to the anchor point. Once you’ve established your anchor point, secure the tree-trunk protector or choker-chain around the object.
STARTING AND OPERATING CAUTION! Always be certain the anchor you select will withstand the load. NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural anchors include trees, stumps and rocks. Hook the cable as low as possible. If no natural anchors are available when recovering another vehicle, your vehicle becomes the anchor point.
STARTING AND OPERATING 267 NOTE: Always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door. Always disconnect the remote control when not in use.
STARTING AND OPERATING 10. Put wire rope under tension. Using the remote control switch, slowly wind the wire rope until no slack remains. Once the wire rope is under tension, stand well clear and never step over it. 11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure. 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope.
STARTING AND OPERATING 13. In certain situations you may decide to throw a heavy blanket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway between the winch and the anchor point. Do this before the wire rope is put under tension. Do not approach or move the blanket once tension is applied. Do not allow it to get pulled into the fairlead. If necessary to move or remove the blanket, slack the tension on the wire rope first.
STARTING AND OPERATING For additional assistance, the winched vehicle can be slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground. If you are able to drive the vehicle, the winching operation is complete. Using The Remote Control NOTE: Avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the winch motor to cool down.
STARTING AND OPERATING 271 an uneven stack, spool out that section of the rope and reposition it to the opposite end of the drum, which will free up space for continued winching. 16. Secure vehicle. Once recovery of the vehicle is complete, be sure to secure the vehicle’s brakes and put the transmission in ⬙park⬙ (automatic) or ⬙low⬙ gear for ⬙manual⬙ transmissions. Release tension in the wire rope. 17. Disconnect wire rope. Disconnect from the anchor. 18. Rewind wire rope.
STARTING AND OPERATING NOTE: How to spool under no load: Arrange the remote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessary. Keep the wire rope under light tension and spool the wire rope back and onto the winch drum in even layers. Stop frequently to tighten and straighten the layers as necessary.
STARTING AND OPERATING RIGGING TECHNIQUES 273 How to change the pulling direction: Various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or maintaining a straight-line pulling situation. You will have to assess what technique is correct for your situation. Think ⬙safety⬙ at all times.
STARTING AND OPERATING will enable you to change your pulling direction while still allowing the wire rope to be at 90° to wind properly onto the spooling drum. Increasing pulling power: In some cases, you may find yourself needing more pulling power.
STARTING AND OPERATING Because pulling power decreases with the number of layers of wire rope on the winch drum, you can use a snatch block to double line out more wire rope. This decreases the number of layers of wire rope on the drum, and increases pulling power. Start by feeding out enough wire rope to free the winch hook. Attach the hook to your vehicle’s frame/tow hook and run the wire rope through a snatch block.
STARTING AND OPERATING LOCK Locks the automatic transmission shift control into the PARK position. It also engages the steering wheel lock (if equipped) when the steering wheel is turned. START Starts the engine. When the engine starts, release the key. The ignition key will return to the ON position for normal driving. NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of Park (P).
STARTING AND OPERATING Manual Transmission Key Release Button 277 Key Reminder An alarm will sound to remind you if the key is left in the ignition and the driver’s door is opened. STARTING PROCEDURES The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating.
STARTING AND OPERATING Automatic Transmission Start the engine with the selector lever in NEUTRAL or PARK position. Apply the brake before shifting to any driving range. Normal Starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure.
STARTING AND OPERATING If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the normal starting procedure should be repeated. WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. After Starting The idle speed is automatically controlled and will decrease as the engine warms up.
STARTING AND OPERATING TRANSMISSION SHIFTING Automatic Transmission with Overdrive The gear shift selector display, located in the instrument panel cluster, indicates the transmission gear range (the selector is illuminated for night driving). The selector lever is mounted on the right side of the steering column. You must depress the brake pedal, to pull the selector lever out of park (P) position (Brake Interlock System).
STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling it toward you after you have set it in P. Make sure it is in Park before leaving the vehicle. WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed.
STARTING AND OPERATING “2” Second Use this position for driving slowly in heavy city traffic or on mountain roads where more precise speed control is desirable. Use it also when climbing long grades, and for engine braking when descending moderately steep grades. NOTE: Do not exceed maximum engine speed. “1” First Use this position for driving up very steep hills and for engine braking at low speeds (20 mph [32 km/h] or less) when going downhill. NOTE: Do not exceed maximum engine speed.
STARTING AND OPERATING NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level. Refer also to the Note under torque converter clutch, later in this section.
STARTING AND OPERATING reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closedthrottle downshifts to 3rd gear (for improved braking) when driving conditions warrant.
STARTING AND OPERATING NOTE: If the vehicle has not been driven in several days, the first few seconds of operation after shifting the transmission into gear may seem sluggish. This is due to the fluid partially draining from the torque converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position. 285 Fully depress the clutch pedal before shifting gears.
STARTING AND OPERATING 5th to 6th requires the same side effort or the lever will return to center resulting in a shift into 4th gear and damage the transmission, clutch, or engine. cruise conditions (relatively steady speeds) will result in increased fuel economy, and may be used as indicated. You should use low gear when starting from a standing position if under a heavy load. To shift into Reverse, come to a complete stop. Depress the clutch and pause briefly to allow the gear train to stop.
STARTING AND OPERATING CAUTION! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage. FOUR-WHEEL- DRIVE OPERATION Manually Shifted Transfer Case Operating Information/Precautions The transfer case provides 4 mode positions - 2 (rear)wheel-drive high range, 4-wheel-drive high range, neutral, and 4-wheel-drive low range.
STARTING AND OPERATING Proper operation of 4-wheel-drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. The transfer case is not equipped with a synchronizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place.
STARTING AND OPERATING 4H 4-Wheel-Drive High Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. 289 Shifting Procedure - Manually Shifted Transfer Case N Neutral - Disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. See Recreational Towing for more information. 4L 4-Wheel-Drive Low Range - Low speed 4-wheel-drive.
STARTING AND OPERATING vehicle in motion, the transfer case will engage / disengage faster if you momentarily release the accelerator pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to N (Neutral) or depress the clutch on a manual transmission.
STARTING AND OPERATING LIMITED-SLIP DIFFERENTIAL — IF EQUIPPED The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit performs similarly to a conventional differential.
STARTING AND OPERATING PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or first gear. Failure to do so may allow the vehicle to roll and cause damage or injury. • Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured.
STARTING AND OPERATING Brake Noise During normal operation of the brake system certain noises may be present from time to time. Occasional ⬙groan⬙ or ⬙squeal⬙ noises may occur during normal operation of the brake system which may not be indicative of a problem. These noises may be heard at any time the brakes are applied but may be more noticeable during the first few brake applications in the morning.
STARTING AND OPERATING 295 WARNING! WARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
STARTING AND OPERATING POWER STEERING Your power steering system will provide mechanical steering capability if power assist is lost. TIRE SAFETY INFORMATION Tire Markings If for any reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will experience a substantial increase in steering effort. MULTI DISPLACEMENT SYSTEM (MDS) - 5.
STARTING AND OPERATING 297 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 299 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING 301 EXAMPLE: 01 = Number representing the year in which the tire was manufactured.(2 digits) —01 means the year 2001. —Prior to July 2000, tire manufacturers were only required to have 1 number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991.
STARTING AND OPERATING Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 305 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1mile (1 km) after a 3 hour period.
STARTING AND OPERATING loading may be required for high speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
STARTING AND OPERATING 309 Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling.
STARTING AND OPERATING 311 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. • Driving style Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 313 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size may result in false speedometer and odometer readings. specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passengers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo. Cold tire inflation pressures for a lightly loaded vehicle will be found on the face of the driver’s door.
STARTING AND OPERATING These cautions apply to all chain traction devices, including link and cable (radial) chains. NOTE: On 4x4 Power Wagon models, class “U” snow chains are permitted on the rear wheels only of vehicles equipped with LT285/70R17D. CAUTION! Do not use tire chains on the 4X4 front wheels of Ram Trucks equipped with LT285/70R17D. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle.
STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off Road type tires.
STARTING AND OPERATING FUEL REQUIREMENTS The 5.7L engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89. The manu5.7L Engines facturer recommends the use of 89 octane for optimum performance.The routine use of premium gasoline is not recommended.
STARTING AND OPERATING We strongly support the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
STARTING AND OPERATING Sulfur In Gasoline If you live in the northeast United States, your vehicle may have been designed to meet California low emission standards with Cleaner-Burning California reformulated gasoline with low sulfur. If such fuels are not available in states adopting California emission standards, your vehicles will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be adversely affected.
STARTING AND OPERATING CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: Tighten the gas cap until you hear a minimum of 3 “clicks”. This is an indication that the gas cap is properly tightened. Make sure that the gas cap is tightened each time the vehicle is refueled.
STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. WARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank. • Never add fuel to the vehicle when the engine is running.
STARTING AND OPERATING • When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help prevent spark knock. If spark knock persists, lighten the load, or engine piston damage may result. • The use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentrations of methanol.
STARTING AND OPERATING • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only.
STARTING AND OPERATING A scorching odor may be detected if you continue to run a malfunctioning engine. The odor may indicate severe and abnormal catalyst overheating. If this occurs, the vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Service, including a tune-up to manufacturer’s specifications should be obtained immediately.
STARTING AND OPERATING rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo. Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded.
STARTING AND OPERATING Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. The entire vehicle should first be weighed on a commercial scale to insure that the GVWR has not been exceeded.
STARTING AND OPERATING 327 NOTE: The weights shown in this chart are not necessarily the weights for your vehicle. Also, the amount of load added to both the front and rear axles can be computed after the vehicle has been weighed both in its ⴖcurb weightⴖ condition, and in its ⴖloaded and ready for operationⴖ condition. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
STARTING AND OPERATING Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale.
STARTING AND OPERATING Frontal Area The maximum height and maximum width of the front of a trailer. Trailer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
STARTING AND OPERATING Trailer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your dealer for package content.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) 331 Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. NOTE: For additional trailer towing information (maximum trailer weight ratings) refer to the following website addresses: • http:// www.dodge.com/towing. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
STARTING AND OPERATING • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual.
STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
STARTING AND OPERATING • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire.
STARTING AND OPERATING Towing Requirements — Trailer Brakes − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required.
STARTING AND OPERATING WARNING! NOTE: Do not cut or splice wiring into the vehicles wiring harness. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you.
STARTING AND OPERATING 337 If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “TOW HAUL” or “OD/OFF” range should be selected. 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
STARTING AND OPERATING NOTE: Check the automatic transmission fluid level before towing. Towing Tips — Tow/Haul (If Equipped) To reduce potential for automatic transmission overheating, turn the “TOW HAUL OD/OFF” feature ON when driving in hilly areas or shift the transmission to Drive position 2 on more severe grades.
STARTING AND OPERATING 339 Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface. NOTE: Fold the 7 x 10 inch trailer towing mirrors rearward prior to entering an automated car wash.
STARTING AND OPERATING SNOWPLOW Dodge Power Wagon Models NOTE: Do not use Dodge Power Wagon Models for snowplow applications. WARNING! Trailer Towing Position Snowplows and other aftermarket equipment should not be added to the front end or your vehicle. The airbag crash sensors may be affected by the change in the front end structure. The airbags could deploy unexpectedly or could fail to deploy during a collision resulting in serious injury or death.
STARTING AND OPERATING CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual 341 RECREATIONAL TOWING — 4–WHEEL DRIVE VEHICLES (BEHIND MOTORHOME, ETC.) CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing.
STARTING AND OPERATING Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped Use the following procedure to prepare your vehicle for recreational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in N (NEUTRAL) before recreational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop. 2. Shut OFF the engine. 3. Depress the brake pedal. 4.
STARTING AND OPERATING CAUTION! Damage to the automatic transmission may occur if the transmission is shifted into P (PARK) with the transfer case in N (NEUTRAL) and the engine RUNNING. With the transfer case in N (NEUTRAL) ensure that the engine is OFF prior to shifting the transmission into P (PARK) Returning to Normal Operation — Manual Shift Transfer Case Use the following procedure to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop. 2. Shut OFF the engine. 3.
STARTING AND OPERATING CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts. TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Lights . . . . . . . . . . . . . . . . . . 346 䡵 Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 347 䡵 Jump-Starting . . . . . . . . . . . . . . . . . . . . . . . . . 356 䡵 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . 348 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 359 ▫ All Models . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING LIGHTS The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. To engage the Hazard Warning lights, depress the button on the top of the steering column. When the Hazard Warning switch is activated, all directional turn signals will flash off and on to warn oncoming traffic of an emergency. Push the button a second time to turn off the flashers.
WHAT TO DO IN EMERGENCIES ADDING FUEL The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable fuel container, it should have a flexible nozzle long enough to force open the restricting door. WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling.
WHAT TO DO IN EMERGENCIES JACK LOCATION All Models The jack and jack tools are stored under the passenger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by loosening the thumb screw and sliding the assembly from under the seat. WARNING! The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure.
WHAT TO DO IN EMERGENCIES 349 CHANGING A FLAT TIRE Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
WHAT TO DO IN EMERGENCIES Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. Do not raise this vehicle using a bumper jack.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. For Power Wagon, when changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front.
WHAT TO DO IN EMERGENCIES 353 WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wheel off. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel on the rear wheel models. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. 6.
WHAT TO DO IN EMERGENCIES WARNING! NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. Hub Caps The hub caps must be removed before raising the vehicle off the ground. 7. Remove wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel.
WHAT TO DO IN EMERGENCIES Wheel Nuts All wheel nuts should be tightened occasionally to eliminate the possibility of wheel studs being sheared or the bolt holes in the wheels becoming elongated. This is especially important during the first few hundred miles of operation to allow the wheel nuts to become properly set. All nuts should first be firmly seated against the wheel. The nuts should then be tightened to recommended torque. Tighten the nuts to final torque in increments.
WHAT TO DO IN EMERGENCIES HOISTING A conventional floor jack may be used at the jacking locations, refer to the graphics that show jacking locations. However, a floor jack or frame hoist must never be used on any other parts or the underbody. CAUTION! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle may result. JUMP-STARTING You should not try to start your vehicle by pushing or towing.
WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
WHAT TO DO IN EMERGENCIES 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3.
WHAT TO DO IN EMERGENCIES EMERGENCY TOW HOOKS — IF EQUIPPED Your vehicle may be equipped with emergency tow hooks. WARNING! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing.
WHAT TO DO IN EMERGENCIES 4-Wheel-Drive Vehicles 361 WINCH USAGE (See page 256 for more information.) CAUTION! To avoid damage to the transfer case while towing, always use the following method. The manufacturer recommends towing with all wheels off the ground. Acceptable methods are to tow vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment— 5.7L . . . . . . . . . . . . . . . 366 䡵 Onboard Diagnostic System (OBD II) . . . . . . . . . 367 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 ▫ Drive Belts — Check Condition And Tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 375 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Power Steering — Fluid Check . . . . . . . . . . . . 380 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 380 ▫ Steering Linkage — Inspection . . . . . . . . . . . . 381 ▫ Front Prop Shaft Lubrication . . . . . . . . . . . . . 382 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 382 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 383 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 383 ▫ Exhaust System . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 365 䡵 Replacement Light Bulbs . . . . . . . . . . . . . . . . . 406 ▫ Cab Top Clearance Lights — If Equipped . . . . 414 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 407 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ Headlight (Halogen)/Front Park And Turn Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 417 ▫ Tail, Stop, Turn And Backup Lights . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing. Normally, the OBD system will be ready. The OBD system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery replacement.
MAINTAINING YOUR VEHICLE b. The MIL light will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. REPLACEMENT PARTS Use of genuine Mopar威 parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance.
MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the ADD and SAFE markings on the dipstick. Adding one quart of oil when the reading is at the ADD mark will result in a SAFE reading on these engines. 371 Change Engine Oil CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine.
MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 32°C (90°F) • Trailer towing • Heavy Loading • Taxi, Police or delivery service (commercial service) • Off-road or desert operation • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.
MAINTAINING YOUR VEHICLE Engine Oil Identification (API) Symbol There is a symbol to aid you in selecting the proper engine oil. This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395.
MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change.
MAINTAINING YOUR VEHICLE Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug, malfunctioning spark plugs can damage the catalytic converter. For proper type of replacement spark plugs, refer to the “Vehicle Emission Control Information” label in the engine compartment.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE Emission-Related Components Positive Crankcase (PCV) Valve Proper operation of the crankcase ventilation system requires that the PCV valve be free of sticking or plugging from deposits. Deposits can accumulate in the PCV valve and passages with increasing mileage. Have the PCV valve, hoses, and passages checked for proper operation at the intervals specified.
MAINTAINING YOUR VEHICLE 379 CAUTION! WARNING! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case. Also, if a “fast charger” is used while battery is in vehicle, disconnect both vehicle battery cables before connecting the charger to battery.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, or Refrigerants.
MAINTAINING YOUR VEHICLE provide assist as the inclination angle of the vehicle increases, i.e. when the vehicle is not on level ground. NOTE: When anticipating any severe offroad/dusty or wet conditions, ensure that the outer tie rod ends are properly greased before ans soon after the vehicle is taken through such conditions. The greasing will help purge contaminants and water from under the seal. Regular greasing will prolong the life of the ball joints.
MAINTAINING YOUR VEHICLE Front Prop Shaft Lubrication Lubricate the front driveshaft grease fitting at each oil change listed in the appropriate Maintenance Schedule for your vehicle (Schedule “A” and “B”). Use Mopar威 type MS-6560 (lithium based grease), or equivalent.
MAINTAINING YOUR VEHICLE Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE directed on the container, aids cleaning action, reduces the freezing point to avoid line clogging, and is not harmful to paint or trim. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE Cooling System Cooling System Maintenance At the intervals shown in the Maintenance Schedules Section of the manual, the system should be drained, flushed and filled. Inspection Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant as specified. Inspect the entire cooling system for leaks.
MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no longer a need to remove the coolant pressure cap except for checking coolant freeze point or replacement with new antifreeze coolant. WARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool an overheated engine! The coolant is under pressure and severe scalding could result.
MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, add the recommended concentration of antifreeze and water to the coolant bottle. Do not overfill. NOTE: Failure to follow the antifreeze concentration and replacement recommendations, or failure to use antifreeze formulated to prevent corrosion of all cooling system metals, may result in radiator plugging, overheating, or cooling system leaks such as in core hole plugs.
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than specified engine coolant, may result in engine damage, and decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do not use plain water alone or alcohol base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE 389 WARNING! Insure nylon tubing in these areas has not melted or collapsed. The warning words “DO NOT OPEN HOT” on the radiator pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
MAINTAINING YOUR VEHICLE The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a “MAX” dot and an “MIN” dot. The fluid level must be kept within these two dots. Do not add fluid above the MAX mark, because leakage may occur at the cap. Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. With disc brakes the fluid level can be expected to fall as the brake linings wear.
MAINTAINING YOUR VEHICLE Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified. Inspect hydraulic brake hoses for surface cracking, scuffing or worn spots. If there is any evidence of cracking, scuffing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take place with possible burst failure. Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance-free system.
MAINTAINING YOUR VEHICLE Drain and Refill Vehicles operated in normal service do not have regularly scheduled oil changes. If fluid has become contaminated with water or to provide the correct viscosity grade, drain and refill. Lubricant Selection Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components.
MAINTAINING YOUR VEHICLE is on level ground, enough lubricant should be added to bring the level to the bottom of the filler hole. Lubricant Selection G56 (6 – Speed Manual Transmission — If Equipped) This transmission does not require periodic changing. If it becomes necessary to add or change the fluid in this transmission, refer to Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature. Verify that solid coating of oil is seen on both sides of the dipstick. If the fluid is low, add as required into the dipstick tube. Do not overfill.
MAINTAINING YOUR VEHICLE 395 Selection Of Lubricant Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. Automatic Transmission Fluid and Filter Change To obtain best performance and long life for automatic transmissions, the manufacturer recommends that they be given regular maintenance service by an Authorized Dodge Dealer or Service Center.
MAINTAINING YOUR VEHICLE Front Wheel Bearings Front wheel bearings for all Dodge Ram Trucks are sealed-for-life. They do not require greasing or seal replacement. In some instances, these bearings will “purge” excess grease and the bearing will look slightly wet. This is normal. Periodic inspection for excess play is recommended. Rear Wheel Bearings — Manufacturer’s Axles These bearings are normally considered permanently lubricated.
MAINTAINING YOUR VEHICLE 397 Noise Control System Required Maintenance & Warranty All vehicles built over 10,000 lbs (4 535 kg) Gross Vehicle Weight Rating and manufactured for sale and use in the United States are required to comply with the Federal Government’s Exterior Noise Regulations. These vehicles can be identified by the Noise Emission Control Label located in the operator’s compartment.
MAINTAINING YOUR VEHICLE Required Maintenance for Noise Control Systems The following maintenance services must be performed every 6 months or 6,000 miles (9 600 km), whichever comes first, to assure proper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed or suspected. Proper maintenance of the entire vehicle will help the effectiveness of the noise control systems.
MAINTAINING YOUR VEHICLE AIR CLEANER • Removal of the air cleaner. • Inverting the air cleaner lid. • Removal of the air ducting. EXHAUST SYSTEM • Removal or rendering inoperative exhaust system components including the muffler or tailpipe. ENGINE COOLING SYSTEM • Removal or rendering inoperative the fan clutch. • Removal of the fan shroud.
MAINTAINING YOUR VEHICLE Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed.
MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE • Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • If you detect any stone chips or scratches in the paint, touch them up immediately.
MAINTAINING YOUR VEHICLE oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar touch up paint on scratches as soon as possible.
MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner or any commercial householdtype glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna.
MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the buckles do not work properly. Dry with a soft tissue. INTEGRATED POWER MODULE 405 An integrated Power Module is located in the engine compartment near the battery. This center contains maxi fuses and mini fuses. A label that identifies each component is printed on the inside cover. 1. Disconnect the battery negative (-) cable before removing the cover. 2. Use specified fuses only. 3. Always properly reinstall the cover.
MAINTAINING YOUR VEHICLE • The electronic shift transfer case should be placed in the 4HI mode and kept in this position to minimize the battery drain. • As an alternative to the above steps you may, disconnect the negative cables from both batteries. NOTE: When reinstalling the IOD fuse, the gages in the Instrument Cluster will do a full sweep, when the ignition key is cycled to RUN. This is a normal condition. REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Bulb No. Overhead Console Lights . . . . . .
MAINTAINING YOUR VEHICLE 407 BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Open the hood 2. Remove the two (2) bolts from the front of the headlight housing.
MAINTAINING YOUR VEHICLE 3. Remove the plug from the inner fender well and remove the nut through the access hole. Rear Headlight Housing Nut Access Inner Fender Plug 4. Pull the housing out from the fender to allow room to disconnect the electrical connectors.
MAINTAINING YOUR VEHICLE 409 NOTE: For easier removal, pull the headlight assembly straight forward, applying the greatest amount of force to the outer edge of the headlight assembly. Bulb Removal 5. Unlock and pull connector straight from the base of the headlight halogen bulb.
MAINTAINING YOUR VEHICLE 6. Twist connector on turn signal/park light bulb 1⁄4 turn and remove connector and bulb from housing. 7. Remove housing from vehicle with headlight halogen bulb in housing. 8. Twist the headlight halogen bulb 1⁄4 turn and remove headlight bulb from the housing. 9. Replace headlight or turn signal bulb. Do not touch the headlight halogen bulb. 10. Reverse procedure for installation of bulbs and housing. Tail, Stop, Turn and Backup Lights 1.
MAINTAINING YOUR VEHICLE 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged. 411 3. Push the red lock slide in on the connector and remove the housing from the vehicle. 4. Remove the four (4) screws from the bulb strip in the housing.
MAINTAINING YOUR VEHICLE 5. Pull the appropriate bulb straight from the bulb strip. 7. While holding the taillight firmly in place, fasten the top screw first. Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. • Top Bulb: Park/Turn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights 6. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE 413 2. Separate the connector holding the housing and wiring harness to the body. • Outside Bulbs: Cargo Lamps 3. Turn desired bulb socket 1⁄4 turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE Cab Top Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. 2. Rotate the socket 1⁄4 turn and pull it from the light assembly.
MAINTAINING YOUR VEHICLE 3. Pull the bulb straight from it’s socket and replace. 415 Fog Lights 1. Reach under the vehicle, unlock and twist connector counterclockwise 1⁄4 turn and remove connector and bulb from housing.
MAINTAINING YOUR VEHICLE 2. Pull bulb straight from the connector. 3. Reverse procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE 417 FLUIDS AND CAPACITIES U.S. Metric 34 gal. 35 gal. 128L 132L 7.0 qts. 6.6L 18.7 qts. 17.7L Fuel 5.7L, 89 Octane 2500 Shortbed Models 2500 Longbed Models Engine Oil (with filter) 5.7L Engine V-8, SAE 5W-20, API Certified Cooling System 5.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection (5.7L) Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) P/N 5011764AB or equivalent. Use SAE 5W-20, API Certified, meeting material standard MS-6395. Refer to oil viscosity chart for alternative grade. Mopar威 Engine Oil Filter, P/N 5281090 or equivalent.
MAINTAINING YOUR VEHICLE 419 Chassis Component Automatic Transmission Transfer Case Manual Transmission Fluid (G-56) Front Driveshaft Grease Fitting. Clutch Linkage Front and Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar威 ATF+4, Automatic Transmission Fluid Mopar威 ATF+4, Automatic Transmission Fluid Mopar威 ATF+4, Automatic Transmission Fluid Use Mopar威 type MS-6560 (lithium based grease), or equivalent. Multipurpose Grease, NLGI Grade 2 E.P.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 422 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 425 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 422 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 422 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES • Heavy Loading. • Taxi, police, or delivery service (commercial service). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.
M 424 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F C (32°). • Trailer towing. • Snowplowing. • Heavy Loading.
M 426 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months, whichever comes first. N C Lubricate Front Drive Shaft Fitting. E Rotate tires. S C H E D U L E S 8 Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Change rear axle fluid. Change front axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting. Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Change rear axle fluid. Change front axle fluid. Check transfer case fluid level. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.
M 428 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months, whichever comes first. N C Lubricate Front Drive Shaft Fitting. E Rotate tires. S C H E D U L E S 8 Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Change rear axle fluid. Change front axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting. Flush and replace engine coolant at 60 months, or 102, 000 miles (170 000 km) whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Drain and refill transfer case fluid. Change rear axle fluid. Change front axle fluid. Change 6-spd manual transmission (G-56) fluid.
M 430 SCHEDULE “B” A I N Miles T (Kilometers) E N Inspect brake linings. A Inspect engine air cleaner filter, replace if necesN C sary. E Replace spark plugs. S C H E D U L E S 8 Replace ignition cables. Inspect PCV valve, replace as necessary.** Drain and refill automatic tranmission fluid and change main sump filter (545RFE only).
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting. Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Inspect engine air cleaner filter. Change rear axle fluid. Change front axle fluid. Inspect brake linings. Inspect auto tension drive belt and replace if required.
M 432 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months, whichever comes first. N C Lubricate Front Drive Shaft Fitting. E Rotate tires. S C H E D U L E S 8 Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Change rear axle fluid. Change front axle fluid. Check transfer case fluid level. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
SCHEDULE “B” Miles (Kilometers) Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
M 434 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 months, A whichever comes first. N C Lubricate Front Drive Shaft Fitting. E Rotate tires. S C H E D U L E S 8 Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Flush and replace engine coolant, if not replaced at 60 months. Inspect brake linings.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting. Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Drain and refill transfer case fluid. Change rear axle fluid. Change front axle fluid. Change 6-spd manual transmission (G-56) fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs.
M 436 SCHEDULE “B” A I N Miles T (Kilometers) E N Replace ignition cables. A Inspect PCV valve, replace as necessary.** N C Inspect auto tension drive belt and replace if E required. S C H E D U L E S 8 105,000 (175 000) X Drain and refill automatic tranmission fluid and change main sump and spin-on cooler return filter (if equipped) [545RFE only]. Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (170 000 km).
SCHEDULE “A” 437 M Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Prop Shaft fitting. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level. Lubricate tie rod end links. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs.
M 438 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Lubricate Front Prop Shaft fitting. E Rotate tires. S C H E D U L E S 8 Check spare tire for proper pressure and correct stowage. Check transfer case fluid level. Lubricate tie rod end links. Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (170 000 km). Inspect brake linings.
SCHEDULE “A” Miles (Kilometers) [Months] Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Replace ignition cables.
M 440 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Lubricate Front Prop Shaft fitting. E Rotate tires. S C H E D U L E S 8 Check spare tire for proper pressure and correct stowage. Lubricate tie rod end links. Check transfer case fluid level. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Prop Shaft fitting. Rotate tires. Check spare tire for proper pressure and correct stowage. Drain and refill transfer case fluid. Flush and replace engine coolant, if not replaced at 60 months. Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (170 000 km). Lubricate tie rod end links. Inspect brake linings. Inspect auto tension drive belt and replace if required.
M 442 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Replace spark plugs. N C Inspect PCV Valve, replace as necessary.** E S C H E D U L E S 8 Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. **This maintenance is recommend, but not required. 102,000 (170 000) [102] 108,000 (180 000) [108] 114,000 (190 000) [114] 120,000 (200 000) [120] X X WARNING! You can be badly injured working on or around a motor vehicle.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444 ▫ Prepare For The Appointment . . . . . . . . . . . . 444 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 444 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 444 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 444 䡵 Warranty Information (U.S. Vehicles Only) . . . . . 447 䡵 Mopar威 Parts . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s dealers have the facilities, factory-trained technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner.
IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center.
IF YOU NEED CONSUMER ASSISTANCE 447 Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. We appreciate that you have made a major investment when you purchased your new vehicle.
IF YOU NEED CONSUMER ASSISTANCE To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1-800-424-9393 (or 366-0123 in Washington DC area) or write to: NHTSA, U.S. Dept. of Transportation, Washington DC 20590. You can also obtain other information about motor vehicle safety from the Hotline. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted.
IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computercontrolled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and driveability procedures, proven diagnostic tests and a complete list of all tools and equipment. • Owner’s Manuals.
INDEX 10
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . 319,347 Air Cleaner, Engine (Engine Air Cleaner Filter) . 375,398 Air Conditioner Maintenance . . . . . . . . . . . . . . . 379 Air Conditioning Refrigerant . . . . . . . . . . . . . 379,380 Air Conditioning System . . . . . . . . . . . . . . . . 216,379 Air Conditioning System, Zone Control . . . . . . . . 219 Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . 306,314 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 301 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 Brake System . . . . . . . . . . . . . . . . . . . . . . . . 293,389 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 Disc Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . 389 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 389 Parking . . . . . . .
INDEX Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176,196 Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391 Clutch Linkage Maintenance . . . . . . . . . . . . . . . . 391 Compact Disc Maintenance . . . . . . . . . . . . . . . . . 212 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 309 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . 138,139 Compass Calibration . . . . . . . . . . . . . . . . . . . . . 139 Compass Variance . . . . .
INDEX Disposal Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 388 Door Ajar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 142 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 Driving Off-Pavement . . . . . . . . . . . . . . . . . . . . . . . . . 235 Off-Road . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 56 Exhaust Gas Caution . . . . . . . . . . . . . . 71,162,322,384 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . 71,384 Exterior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 123 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . 375,398 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 374,418 Engine Oil Disposal .
INDEX Gas Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 317 Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Coolant Temperature . . . . . . . . . . . . . . . . . . . . 170 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Speedometer . .
INDEX Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15,275 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12,15 Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 57,58 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . 314 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 84 Instrument Cluster . . . . . . . . . . . . . . . . . . . .
INDEX Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 124 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . 124,174,415 Four-Wheel Drive Indicator . . . . . . . . . . . . . . . 290 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 346 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 High Beam . . . . . . . . . . . . . . . . . . . . . . . . 127,169 High Beam Indicator . . . . . . . . . . . . .
INDEX Maintenance Procedures . . . . . . . . . . . . . . . . . . . 370 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 422 Schedule ⬙A⬙ . . . . . . . . . . . . . . . . . . . . . . . . . 437 Schedule ⬙B⬙ . . . . . . . . . . . . . . . . . . . . . . . . . . 425 Malfunction Indicator Light . . . . . . . . . . . . . . . . 368 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 448 Manual Transmission . . . . . . . . . . . . . . . . . . 285,392 Fluid Level Check . . . . . . . . .
INDEX Materials Added to . . . . . . . . . . . . . . . . . . . . . 373 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . 169 Recommendation . . . . . . . . . . . . . . . . . . . 372,417 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . 373,417 Onboard Diagnostic System . . . . . . . . . . . . . . . . 367 Opener, Garage Door . . . . . . . . . . . . . . . . . . . . . 142 Operating Precautions . . . . . . . . . . . .
INDEX Programming Transmitters . . . . . . . . . . . . . . 143,147 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 308 Radiator Cap (Coolant Pressure Cap) . . . . . . . 385,388 Radio Operation . . . . . . . . . . . . . . . . . . . 177,182,195 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . 210 Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . . . . . 209 Radio (Sound Systems) . . . . . . . . . . . . . . 177,182,195 Ramp Travel Index . . . . . . . . . . . . .
INDEX Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . 33,34,72 Adjustable Upper Shoulder Anchorage . . . . . . . . 41 And Pregnant Women . . . . . . . . . . . . . . . . . . . 45 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 57,69 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Reminder . . . . . . . . . . . . . . . .
INDEX Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . 309,310 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 Compact Spare . . . . . . . . . . . . . . . . . . . . . . . . 309 General Information . . . . . . . . . . . . . . . . . . . . 305 High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 307 Inflation Pressures . . . . . . . . . . . . . . . . . . . . . 306 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Load Capacity . . . . . . . . . . . . . . . . . . . . . 301,302 Off-Road . . . . . . . . . . . . . . .
INDEX Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 Transmission Automatic . . . . . . . . . . . . . . . . . . . . . . . . 280,393 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 Maintenance . . . . . . . . . . . . . . . . . . . . . . . 392,393 Manual . . . . . . . . . . . . . . . . . . . . . . . . 277,285,392 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . 280,286 Transmitter, Garage Door Opener . . . . . . . . . . . .
INDEX Rigging Techniques . . . . . . . . . . . . . . . . . . . . . 273 Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 32,151 Window Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 224 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Rear Sliding . . . . . .
