2011 Nitro 2011 OWNER’S MANUAL Chrysler Group LLC 11KA74-126-AB Second Edition Printed in U.S.A.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7 䡵 Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 7 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
INTRODUCTION 5 injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire.
6 INTRODUCTION
INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ To Disarm The System . . . . . . . . . . . . . . . . . 18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 12 䡵 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . 19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . 14 䡵 Remote Keyless Entry (RKE) . . . . . . . . . . . . . . 19 䡵 Sentry Key威 . . . . . . . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . 24 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 37 ▫ General Information . . . . . . . . . . . . . . . . . . . 25 䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 䡵 Remote Starting System — If Equipped . . . . . . . 25 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 38 ▫ How To Use Remote Start . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Enhanced Seat Belt Use Reminder System (BeltAlert威) — If Equipped . . . . . . . . . . . . . . 52 ▫ Seat Belt Lock Out . . . . . . . . . . . . . . . . . . . . 54 ▫ Seat Belts And Pregnant Women . . . . . . . . . . 54 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 54 ▫ Supplemental Restraint System (SRS) — Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 ▫ Airbag Deployment Sensors And Controls . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The keys for your new vehicle are enclosed in a plastic A WORD ABOUT YOUR KEYS The keys for your vehicle are double-sided. You can bag with the key code number on it. If you received your insert the keys into the locks with either side up. keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by an authorized dealer from your vehicle invoice.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle. The system will shut the engine off in two Key-In-Ignition Reminder If you open the driver’s door and the key is in the seconds if someone uses an invalid key to try to start the ignition, a chime will sound to remind you to remove the engine. key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. CAUTION! The Sentry Key威 Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE procedure. This procedure consists of programming a 3. Insert the second valid key into the ignition switch. blank key to the vehicle electronics. A blank key is one Turn the ignition switch to the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound. In that has never been programmed. addition, the Vehicle Security Light will begin to flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Repeat this procedure to program up to eight keys. If you VEHICLE SECURITY ALARM — IF EQUIPPED do not have a programmed Sentry Key威, contact your The Vehicle Security Alarm monitors the vehicle doors, liftgate, and ignition for unauthorized operation. When authorized dealer for details. the Vehicle Security Alarm is activated, interior switches NOTE: If a programmed key is lost, see your authorized for door locks are disabled.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Arm the System Remove the keys from the ignition switch and exit vehicle. Lock the doors and liftgate by pressing power door LOCK switch or the LOCK button on Remote Keyless Entry (RKE) transmitter. Close all doors. To Disarm the System the Either press the UNLOCK button on the RKE transmitter the or insert a valid Sentry Key威 into the ignition lock the cylinder and turn the key to the ON/RUN position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tamper Alert If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering. ILLUMINATED ENTRY The interior lights come on when you open any door or use the Remote Keyless Entry (RKE) transmitter to unlock any door. They will remain on for approximately 30 seconds after all doors are closed then fade to off.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Remote Key Unlock, Driver Door/All Doors First • For the remote starting feature (if equipped), refer to This feature lets you program the system to unlock either “Remote Starting System” for further information. the driver’s door or all doors and the liftgate on the first press of the UNLOCK button on the RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 3. Test the feature from outside the vehicle by pressing Sound Horn with Lock the LOCK and UNLOCK buttons on the RKE transmitter. This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be 4. Repeat these steps if you want to return this feature to turned on or off. To change the current setting, proceed as its previous setting.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the feature from outside the vehicle by pressing • On Electronic Vehicle Information Center (EVIC) the LOCK button on the RKE transmitter. equipped vehicles, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer4. Repeat these steps if you want to return this feature to Programmable Features)” in “Understanding Your Inits previous setting. strument Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 3. Test the feature from outside the vehicle by pressing Using the Panic Alarm the LOCK and UNLOCK buttons on the RKE transmitter. NOTE: The PANIC and SECURITY alarms are quite 4. Repeat these steps if you want to return this feature to different. Please take a moment to activate the PANIC and SECURITY modes to hear the differences in the horn. its previous setting.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE During the PANIC mode, the door locks and RKE systems will function normally. PANIC mode will not disarm the Vehicle Security Alarm system on vehicles so equipped. 2. With the RKE transmitter buttons facing down, use a flat blade to pry the two halves of the RKE transmitter case apart. Make sure not to damage the seal during removal. Programming Additional Transmitters Refer to Sentry Key威 “Customer Key Programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 3. Remove and replace the battery. Avoid touching the NOTE: Changes or modifications not expressly apnew battery with your fingers. Skin oils may cause proved by the party responsible for compliance could battery deterioration. If you touch a battery, clean it with void the user’s authority to operate the equipment. rubbing alcohol. If your RKE transmitter fails to operate from a normal 4.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How to Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed WARNING! • Do not start or run an engine in a closed garage or confined area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: • The brake pedal is pressed • The park lamps will turn on and remain on during To Exit Remote Start Mode without Driving the Remote Start mode. Vehicle • For security, power window and power sunroof op- Press and release the REMOTE START button one time, eration (if equipped) are disabled when the vehicle is or allow the engine to run for the entire 15-minute cycle. in the Remote Start mode.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! Manual Door Locks Use the manual door lock knob to lock the doors from inside the vehicle. If the lock knob is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 A chime will sound if the key is in the ignition switch and a door is open as a reminder to remove the key. Automatic Door Locks The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The automatic door locks feature is enabled. 2. The transmission is in gear. 3. All doors are closed. 4. The throttle is pressed. Power Door Lock Switch 1 - Unlock 2 - Lock 5.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will indicate the completion of the Automatic Door Locks Programming The automatic door locks feature can be enabled or programming. disabled as follows: 5. Repeat these steps if you want to return this feature to For vehicles equipped with an Electronic Vehicle Infor- its previous setting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. The vehicle speed is 0 mph (0 km/h). 31 3. Press the power door UNLOCK switch to unlock the doors. Automatic Unlock Doors on Exit Programming The automatic unlock doors on exit feature can be 4. A single chime will indicate the completion of the enabled or disabled as follows: programming.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE system on a door is engaged, that door can only be NOTE: opened by using the outside door handle even if the • When the child lock system is engaged, the door can be opened only by using the outside door handle even inside door lock is in the unlocked position. though the inside door lock is in the unlocked position. • After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged. WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger/rear passenger doors which operates the front Power Window Switches passenger/rear passenger door windows.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Personal Settings (Customer-Programmable Features)” in To open the window part way, press the window switch “Understanding Your Instrument Panel” for further in- to the first detent and release it when you want the window to stop. formation. WARNING! Never leave children in a vehicle with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Up Feature with Anti-Pinch Protection — If Equipped On some models, the driver’s and front passenger’s (if equipped for passenger side) power window switches have an “Auto Up” feature. Pull the window switch up to the second detent, release, and the window will go up automatically. 35 For vehicles equipped with the EVIC, the power window switches will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Reset At some point in time, it may be necessary to reactivate the auto-up feature. To do so, perform the following procedure: Window Lockout Button The window lockout button on the driver’s door (below the power window switches) allows you to disable the window control on the other doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS • Front seat belts incorporate pretensioners to enhance Some of the most important safety features in your occupant protection by managing occupant energy vehicle are the restraint systems: during an impact event • Three-point lap and shoulder belts for all seating • All seat belt systems (except the driver’s and rear positions center) include Automatic Locking Retractors (ALRs), which lock the seat belt webbing into position by • Advanced
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause an accident that includes you. This can happen far away from home or on your own street. Please pay close attention to the information in this section.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or accidents. This feature allows the shoulder part of the belt to move freely with you under normal conditions. However, in an accident the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is located on the B-Pillar along the outboard side and rear of the seat cushion. The rear seat belt latch plates are located on the C-Pillar for the outboard rear seating positions and next to your arm in the center rear seating position. Grasp the latch plate and pull out the belt.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in an accident, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during an accident.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Position the shoulder belt on your chest so that it is 6. To release the belt, push the red button on the buckle. comfortable and not resting on your neck. The retractor The belt will automatically retract to its stowed position. will withdraw any slack in the belt. If necessary, slide the latch plate down the webbing to allow it to retract fully. WARNING! A frayed or torn belt could rip apart in an accident and leave you with no protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 of a collision. These devices improve the performance of Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ the seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners work for all shoulder belt. size occupants, including those in child restraints. 1. Position the latch plate as close as possible to the NOTE: These devices are not a substitute for proper seat anchor point.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pressing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 • ALR — Automatic Locking Retractor When To Use The Automatic Locking Mode Use the Automatic Locking Mode anytime a child safety If the passenger seating position is equipped with an seat is installed in a seating position that has a belt with ALR and is being used for normal usage: this feature. Children 12 years old and under should Only pull the belt webbing out far enough to comfortably always be properly restrained in the rear seat.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Active Head Restraints (AHR) These head restraints are passive, deployable components, and vehicles with this equipment cannot be readily identified by any markings, only through visual inspection of the head restraint. The head restraint will be split in two halves, with the front half being soft foam and trim, the back half being decorative plastic.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 CAUTION! All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident. NOTE: For more information on properly adjusting and positioning the head restraint, refer to “Adjusting Active Head Restraints” in “Understanding The Features Of Your Vehicle”.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand Positioning Points On AHR 2. Position the hands on the top of the deployed AHR at a comfortable position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 2 3 — Final Downward Movement To Engage Locking Mechanism AHR In Reset Position NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the Active Head Restraints, see an authorized dealer. into the back decorative plastic half. • For safety reasons, have the Active Head Restraints checked by a qualified specialist at an authorized dealer.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Energy Management Feature This vehicle has a safety belt system with an energy management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on accident. Enhanced Seat Belt Use Reminder System (BeltAlert姞) — If Equipped BeltAlert威 is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert威) to fasten their seatbelts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front passenger seat BeltAlert威 is not active when the front passenger seat is unoccupied. BeltAlert威 may be triggered when an animal or heavy object is on the front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed. 53 2.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE extender should be used only if the existing belt is not Seat Belt Lock Out The center rear seat belt system has a lock out feature that long enough. When it is not required, remove the exwill not allow you to extract the center webbing unless tender and store it. the rear seat upper latch is engaged. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 panel, above the glove compartment. The words SRS/ The Advanced Front Airbags have a multistage inflator AIRBAG are embossed on the airbag covers. design. This allows the airbag to have different rates of inflation that are based on the severity and type of NOTE: These airbags are certified to the new Federal collision. regulations for Advanced Airbags.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle is equipped with Supplemental Side Airbag NOTE: Inflatable Curtains (SABIC) that run the entire length of • Airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. the headliner to protect the driver, front, and rear passengers sitting next to a window. • After any accident, the vehicle should be taken to an authorized dealer immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • Supplemental Side Airbag Inflatable Curtains (SABIC) Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver • Front and Side Impact Sensors and front passenger airbags.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • No objects should be placed over or near the airbag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the airbag to inflate. • Do not put anything on or around the Advanced Front Airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags may no longer be functional.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) SABIC airbags may offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The SABIC airbags deploy downward, covering both windows on the impact side.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • If your vehicle is equipped with SABIC airbags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (Refer to “Child Restraints”) 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided under “If You Need Assistance”.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Airbag deployment could cause serious injury, including death. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • The Supplemental Side Airbag Inflatable Curtains (SABIC) need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 The SABIC will not deploy in all side collisions. SABIC The ORC contains a backup power supply system that deployment will depend on the severity and type of may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. collision. Also, the ORC turns on the “Airbag Warning Light” for four to eight seconds for a self-check when the ignition is first turned to ON/RUN.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the “Airbag Warning Light” in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the airbag system immediately. Occupant Classification System (OCS) The OCS is part of a Federally regulated safety system required for this vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “PASS AIR BAG OFF” to show that the passenger Advanced Front Airbag will not inflate during a collision requiring airbag deployment. When the right front passenger seat is empty or when very light objects are placed on the seat, the passenger airbag will not inflate even though the PAD indicator light is not illuminated. 65 The PAD indicator light should not be illuminated when an adult passenger is properly seated in the front passenger seat.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never place a rear facing infant seat in front of an airbag. A deploying passenger Advanced Front Airbag can cause death or serious injury to a child in a rear-facing infant seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If there is a fault present in the airbag system, the Airbag Warning Light (a red light located in the center of the instrument cluster directly in front of the driver) will be turned on. This indicates that you should have an authorized dealer service the system immediately. The Airbag Warning Light is turned on whenever there is a fault that can affect the operation of the airbag system.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front Airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If your vehicle is equipped with left and right Supplemental Side Airbag Inflatable Curtains (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the SABIC is located should remain free from any obstructions. 69 The following requirements must be strictly adhered to: • Do not modify the front passenger seat assembly or components in any way.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: 71 the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel or the headliner along the side rails.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. The airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the airbag system immediately. 73 bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the EDR under normal driving conditions and no personal data (e.g. name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation. Children 12 years and younger should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Child Restraints • Safety experts recommend that children ride rearwardfacing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used: rearward-facing infant carriers and “convertible” child seats. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg).
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. Chrysler Group LLC also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The belt-positioning booster seat is for children weighing • Check belt fit periodically. A child’s squirming or more than 40 lbs (18 kg), but who are still too small to fit slouching can move the belt out of position. the vehicle’s seat belts properly. If the child cannot sit • If the shoulder belt contacts the face or neck, move the with knees bent over the vehicle’s seat cushion while the child closer to the center of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 If you are installing LATCH-compatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not LATCHcompatible, you can only install the child restraints using the vehicle’s seat belts.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. Tether Strap Mounting Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a Latch Anchorages means of adjusting the tension in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next, attach the lower hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pull the belt from the retractor until there is enough to allow it to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is completely extracted from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion around the child restraint. Refer to “Automatic Locking Mode”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in an accident.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Do not run the engine in a closed garage or in confined damaged, have a competent mechanic inspect the comareas any longer than needed to move your vehicle in or plete exhaust system and adjacent body areas for broken, out of the area. damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes If it is necessary to sit in a parked vehicle with the engine to seep into the passenger compartment.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 WARNING! (Continued) WARNING! (Continued) • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside the Vehicle Door Latches Check for positive closing, latching, and locking. Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . 106 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 93 ▫ Uconnect™ Phone Features . . . . . . . . . . . . . 109 ▫ Automatic Dimming Mirror — If Equipped . . . 94 ▫ Advanced Phone Connectivity . . . . . . . . . . . 114 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . 132 ▫ Headlights And Parking Lights . . . . . . . . . . 148 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 ▫ Daytime Running Lights — If Equipped . . . . 149 ▫ Driver’s Power Seat — If Equipped . . . . . . . 133 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 149 ▫ Heated Seats — If Equipped . . . . . . . . . . . . 134 ▫ High/Low Beam Switch . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 156 91 ▫ Service Parksense威 Rear Park Assist . . . . . . . 165 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . 156 䡵 Garage Door Opener — If Equipped . . . . . . . . 165 䡵 Electronic Speed Control — If Equipped . . . . . 157 ▫ Programming HomeLink威 . . . . . . . . . . . . . . 167 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . .
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Closing Sunroof — Express . . . . . . . . . . . . . 173 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 ▫ Closing Sunroof — Manual Mode . . . . . . . . 173 ▫ Glove Box Storage Compartment . . . . . . . . . 178 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 173 ▫ Front Storage Compartment . . . . . . . . . . . . . 179 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . 174 ▫ Console Storage Compartment . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. Sensor to the right of the button does not illuminate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror. Power Mirrors The power mirror switch is located on the driver’s door trim panel.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover will turn off the light. Sun Visor “Slide-On-Rod” Feature The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the visor to block out the sun. 1. Fold down the sun visor. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Bluetooth威 technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so Uconnect™ Phone works no matter where you stow your mobile phone (be it your purse, pocket, or briefcase), as long as your phone For Uconnect™ customer support, visit the following is turned on and has been paired to the vehicle’s websites: Uconnect™ Phone.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone Button The radio or steering wheel controls (if equipped) will contain the two control buttons button and Voice (Uconnect™ Phone button) that will enable you Command to access the system. When you press the button you will hear the word Uconnect™ followed by a BEEP. The beep is your signal to give a command. Voice Command Button Actual button location may vary with the radio. The individual buttons are described in the “Operation” section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For certain operations, compound commands can be used. For example, instead of saying “Setup” and then “Phone Pairing”, the following compound command can be said: “Setup Phone Pairing.” • For each feature explanation in this section, only the compound form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To complete the pairing process, you will need to reference • For identification purposes, you will be prompted to your mobile phone Owner’s Manual. The Uconnect™ give the Uconnect™ Phone a name for your mobile website may also provide detailed instructions for pairing. phone. Each mobile phone that is paired should be given a unique phone name.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dial by Saying a Number • Press the button to begin. 101 • The system will prompt you to say the name of the person you want to call. • After the “Ready” prompt and the following beep, say the name of the person you want to call. For example, you can say “John Doe”, where John Doe is a previously stored name entry in the Uconnect™ phonebook • The system will prompt you to say the number you or downloaded phonebook. To learn how to store a want to call.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say The Uconnect™ Phone will allow you to enter up to 32 names in the phonebook with each name having up to “Phonebook New Entry”. four associated phone numbers and designations. Each • When prompted, say the name of the new entry. Use of language has a separate 32-name phonebook accessible long names helps the Voice Command and it is recomonly in that language. In addition, if equipped and mended.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • Automatic download and update, if supported, begins • This downloaded phonebook cannot be edited or as soon as the Bluetooth威 wireless phone connection is deleted on the Uconnect™ Phone. These can only be made to the Uconnect™ Phone, for example, after you edited on the mobile phone. The changes are transstart the vehicle. ferred and updated to Uconnect™ Phone on the next phone connection.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Edit Uconnect™ Phonebook Entries • The phone handset must support Bluetooth威 OBEX NOTE: transfers of phonebook entries to use this feature. • Editing names in the phonebook is recommended when the vehicle is not in motion. • Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth威, • Automatic downloaded phonebook entries cannot be and you may see a message on the phone display that deleted or edited.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 After you are finished editing an entry in the phonebook, • After you enter the Phonebook Delete menu, you will you will be given the opportunity to edit another entry in then be asked for the name of the entry that you wish the phonebook, call the number you just edited, or return to delete. You can either say the name of a phonebook to the main menu.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete/Erase “All” Uconnect™ Phonebook Entries • Press the button to begin. • After the “Ready” prompt and the following beep, say “Phonebook Erase All”. • After the “Ready” prompt and the following beep, say “Phonebook List Names”. • The Uconnect™ Phone will play the names of all the phonebook entries, including the downloaded phonebook entries, if available.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the Uconnect™ Phone. Check with your mobile service provider for the features that you have.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place/Retrieve a Call From Hold To put a call on hold, press the button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the button until you hear a single beep. Three-Way Calling To initiate three-way calling, press the button while a call is in progress, and make a second phone call, as described under “Making a Second Call While Current Call is in Progress”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Redial • Press the button to begin. 109 ends, or until the vehicle battery condition dictates cessation of the call on the Uconnect™ Phone and transfer of the call to the mobile phone. • After the “Ready” prompt and the following beep, say • After the ignition key is switched to OFF, a call can “Redial”.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say If the phone is not reachable and the Uconnect™ Phone is the name of the language you wish to switch to operational, you may reach the emergency number as follows: English, Espanol, or Francais. • Continue to follow the system prompts to complete • the language selection. • After selecting one of the languages, all prompts and voice commands will be in that language. Press the button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • If supported, this number may be programmable on Towing Assistance button and If you need towing assistance: some systems. To do this, press the say “Setup”, followed by “Emergency”. • Press the button to begin. • The Uconnect™ Phone does slightly lower your • After the “Ready” prompt and the following beep, say chances of successfully making a phone call as to that “Towing Assistance”. for the mobile phone directly.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your Uconnect™ Phone that normally requires you to enter in a touch-tone sequence on your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “Send”. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can Voice Mail Calling button and say, “3 7 4 6 # Send”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 The Uconnect™ Phone will then send the corresponding Turning Confirmation Prompts ON/OFF phone number associated with the phonebook entry, as Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect™ tones over the phone. Phone will not repeat a phone number before you dial it). NOTE: • You may not hear all of the tones due to mobile phone • Press the button to begin. network configurations. This is normal.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Mobile Phone Keypad You can dial a phone number with your mobile phone keypad and still use the Uconnect™ Phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 mobile phone, the audio will be played through your vehicle’s audio system. The Uconnect™ Phone will work the same as if you dial the number using Voice Command.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 from your Uconnect™ Phone paired mobile phone to the • When prompted, say “List Phones”. button Uconnect™ Phone or vice versa, press the • The Uconnect™ Phone will play the phone names of and say “Transfer Call”. all paired mobile phones in order from the highest to the lowest priority.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the Uconnect™ Phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. Things You Should Know About Your Uconnect™ Phone Uconnect™ Phone Tutorial To hear a brief tutorial of the system features, press the button and say “Uconnect™ Tutorial.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 You can either press the Uconnect™ Phone button to Voice Command restore the factory setting or repeat the words and • For best performance, adjust the rearview mirror to phrases when prompted by the Uconnect™ Phone. For provide at least 1⁄2 in (1 cm) gap between the overhead best results, the Voice Training session should be comconsole (if equipped) and the mirror.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • dry weather condition. • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • You can say “O” (letter “O”) for “0” (zero). • Even though the system is designed for users speaking in North American English, French, and Spanish ac- • Even though international dialing for most number combinations is supported, some shortcut dialing cents, the system may not always work for some.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. 119 SMS Uconnect™ Phone can read or send new messages on your phone. Read Messages: • Performance, such as audio clarity, echo, and loudness If you receive a new text message while your phone is to a large degree rely on the phone and network, and connected to Uconnect™ Phone, an announcement will not the Uconnect™ Phone.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Where are you? Send Messages: You can send messages using Uconnect™ Phone. To send 4. I need more direction. a new message: 5. L O L • Press the button. 6. Why • After the “Ready” prompt and the following beep, say 7. I love you “SMS Send” or “Send Messages.” • You can either say the message you wish to send or say 8. Call me “List Messages.” There are 20 preset messages. 9. Call me later button while the 10.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me Turn SMS Incoming Announcement ON/OFF Turning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming messages. • Press the button. • After the “Ready” prompt and the following beep, say “Setup, Incoming Message Announcement,” you will then be given a choice to change it.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 3
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) 125 Voice Commands Alternate(s) Primary call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 3
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect™ Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If you do not say a command within a few When using this system, you should speak clearly and at seconds, the system will present you with a list of a normal speaking volume. options. The system will best recognize your speech if the winIf you ever wish to interrupt the system while it lists dows are closed, and the heater/air conditioning fan is button, listen set to low. options, press the Voice Command for the beep, and say your command.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Changing the Volume In this mode, you can say the following commands: 1. Start a dialogue by pressing the Voice Command button. • “Radio” (to switch to the radio mode) 129 • “Disc” (to switch to the disc mode) 2. Say a command (e.g., “Help”). • “Memo” (to switch to the memo recorder) 3. Use the ON/OFF VOLUME rotary knob to adjust the • “System Setup” (to switch to system setup) volume to a comfortable level while the Voice Command system is speaking.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio FM • “Previous Channel” (to select the previous channel) To switch to the FM band, say “FM” or “Radio FM”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: 131 − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) • “New Memo” (to record a new memo) — During the System Setup recording, you may press the Voice Command button to stop recording. You proceed by saying one of To switch to system setup, say “Setup”.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect™ vehicle. Voice “Voice Training” feature may be used. button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Power Seat — If Equipped Some models may be equipped with a six-way power driver seat. The power seat switch is located on the outboard side of the front seat cushion. Use this switch to move the seat up or down, forward or rearward or to tilt the seat. 133 Adjusting the seat forward or rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seatbelts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seatbelt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 You can choose from HIGH, LOW or OFF heat settings. NOTE: Once a heat setting is selected, heat will be felt Amber indicator lights in each switch indicate the level of within two to five minutes. heat in use. Two indicator lights will illuminate for WARNING! HIGH, one for LOW and none for OFF. Press the switch once to select HIGH-level heating. Press the switch a second time to select LOW-level heating.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. Front Manual Seat Adjustment For models equipped with manual seats, the driver and passenger seats can be adjusted forward or rearward by using a bar by the front of the seat cushion, near the floor. Manual Seat Adjustment While sitting in the seat, lift up on the bar located and move the seat forward or rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seatbelts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seatbelt.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Front Passenger Seat The front passenger seatback can be folded flat to allow for extended cargo space. Pull up on the lever to fold down the seatback. Head Restraints Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Active Head Restraints — Front Seats Active Head Restraints are passive, deployable components, and vehicles with this equipment cannot be readily identified by any markings, only through visual inspection of the head restraint. The head restraint will be split in two halves, with the front half being soft foam and trim, the back half being decorative plastic. 139 To raise the head restraint, pull upward on the head restraint.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Static Head Restraints — Rear Seats The two outboard seat are equipped with adjustable head • The head restraints should only be removed by qualirestraints. To raise the head restraint, pull upward on the fied technicians, for service purposes only. If either of head restraint. To lower the head restraint, press the the head restraints require removal, see your authoadjustment button, located on the base of the head rized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 60/40 Split Folding Rear Seat with Fold-Flat Feature To provide additional storage area, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear seating room. 143 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. To Lower Rear Seat Rear Seat Release Strap 3. Fold the rear seat completely forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 To Raise Rear Seat Recliner Adjustment If locked in the folded position, pull the release strap The rear seatback also reclines for additional passenger (toward the front of the vehicle). comfort. Pull the release strap while sitting in the rear seat to recline the seatback. Raise the seatback and lock it into place.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. TO OPEN AND CLOSE THE HOOD To open the hood, there are two latches that must be released. 1. Pull the hood release lever located under the left side of the instrument panel. Hood Release Lever 2. Push the safety latch lever to the right.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 CAUTION! (Continued) • Lower the hood to approximately 6 in (15.2 cm) above the closed position and drop the hood to latch it. • Never drive your vehicle unless the hood is fully closed, with both latches engaged. NOTE: Ensure hood prop rod is fully seated into clip before closing hood to prevent damage to grille. WARNING! Safety Latch Be sure the hood is fully latched before driving your vehicle.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Multifunction Lever The multifunction lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming and turn signals. The multifunction lever is located on the left side of the steering column. Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 To change the brightness of the instrument panel lights, Lights-On Reminder rotate the center portion of the multifunction lever up or If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door down. is opened. NOTE: If the driver’s door is left open, and the headlights or parking lights are left on, a chime will sound.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Fog Lights — If Equipped The front fog light switch is in the multifunction lever. To activate the front fog lights, turn on the parking or low beam headlights and pull out the end of the lever. NOTE: The fog lights will only operate with the parking lights or the headlights on low beam. Selecting high beam headlights will turn off the fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. 151 Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the center portion of the lever upward to the last The overhead light will automatically turn off in approximately 10 minutes if a door is left open or the dimmer detent to turn on the interior lighting. control is left in the dome light position and the key is not in the ignition. Turn the ignition switch ON to restore the overhead light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 washer, refer to “Rear Window Features” in “Under- Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operastanding the Features of Your Vehicle”. tion. 3 Wiper/Washer Lever Windshield Wiper Operation Rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper operation.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The wipers will automatically return to the “park” position if you turn OFF the ignition switch while they are operating. The wipers will resume operation when you turn the ignition switch back to the ON position. CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield Washers To use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired (for a maximum of 10 seconds).
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during windshield washer use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push the lever down to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Pull the lever up to lock the column firmly in place. 157 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Electronic Speed Control lever is located on the right System can be reactivated by pushing the Electronic side of the steering wheel. Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system off, push the ON/OFF button a second time. The CRUISE indicator will turn off. The system should be turned off when not in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 To Set a Desired Speed Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. To Vary the Speed Setting When the Electronic Speed Control is set, you can increase speed by pushing up and holding the RESUME ACCEL lever.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the SET DECEL lever once will result in a 1 mph (2 km/h) decrease in set speed. Each subsequent tap of the lever results in a decrease of 1 mph (2 km/h). To Accelerate for Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Jackhammers, large trucks, and other vibrations could affect the performance of ParkSense威. • When you turn ParkSense威 off, the instrument cluster will display “PARK ASSIST DISABLED.” Furthermore, once you turn ParkSense威 off, it remains off until you turn it on again, even if you cycle the ignition key.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! (Continued) • Clean the ParkSense威 sensors with water, car wash soap, and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. • Before using the ParkSense威 Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Vehicles Equipped With the Electronic Vehicle Information Center (EVIC) You can turn ParkSense威 on or off through the EVIC. Refer to “Electronic Vehicle Information Center (EVIC)/ Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the ignition is turned to the ON position, and the system is enabled, the warning display will turn on all of its LEDs for approximately one second. Then, the system dimly illuminates the two inner most LEDs when it is detecting no obstacles. ParkSense威 is active when the ignition is in the ON position, and the system is enabled, and the driver shifts the transmission into the REVERSE position, and the vehicle speed is less than 11 mph (18 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service ParkSense姞 Rear Park Assist When the ParkSense威 Rear Park Assist System is defective, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “SERVICE PARK ASSIST SYSTEM” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active. WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink姞 167 Place the handheld transmitter 1–3 in (3-8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to the heading “Programming A Rolling Code System.” This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 1. Firmly press and release the LEARN or TRAINING Gate Operator/Canadian Programming button. The name and color of the button may vary by Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of manufacturer. transmission – which may not be long enough for NOTE: You have 30 seconds in which to initiate the next HomeLink威 to pick up the signal during programming. step after the LEARN button has been pressed.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you unplugged the device for training, plug it back in 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not at this time. release the button. Then proceed with Step 4 under “Programming 3. Without releasing the button, proceed with ProgramHomeLink威” earlier in this section. ming HomeLink威 Step 2 and follow all remaining steps.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Troubleshooting Tips General Information If you are having trouble programming HomeLink威, here This device complies with FCC rules Part 15 and Industry are some of the most common solutions: Canada RSS-210. Operation is subject to the following two conditions: • Replace the battery in the original transmitter. 1. This device may not cause harmful interference. • Press the LEARN button on the Garage Door Opener to complete the training for a Rolling Code. 2.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch WARNING! • Never leave unattended children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express Press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. 173 position. The sunroof will close fully and stop automatically. This is called “Express Close”.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing and moves the sunroof in the opposite direction, press the switch forward and hold. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the ⬙Vent⬙ button within one-half second and the sunroof will open to the vent position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. 175 ELECTRICAL POWER OUTLET Your vehicle is equipped with a fused 12 Volt (13 Amp) power outlet. This power outlet is located on the instrument panel, below the climate controls.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. Front Power Outlet WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear passengers have cupholders at the rear of the STORAGE center console. Glove Box Storage Compartment The glove box storage compartment is located on the right side of the instrument panel. Pull outward on the latch to open the storage compartment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Front Storage Compartment Console Storage Compartment The front storage compartment (located on the left side of To open, press the latch and lift the cover. the instrument panel) can hold cell phones, PDAs, and other small items.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console has a removable storage tray which CARGO AREA FEATURES can hold cell phones, PDAs, and other small items. Cargo Light The cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multifunction lever to the extreme top position. Cargo Tie-Down Hooks The tie-downs located on the cargo area floor should be used to safely secure loads when the vehicle is moving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 WARNING! Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. WARNING! Cargo Tie-Downs The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 3. Flip the cover over, and lock panel back into position. 3 Floor Panel 2. Lift the cover.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rotate the switch upward to the first detent position for rear wiper operation. Rear Window Wiper/Washer The rear wiper/washer is controlled by a rotary switch NOTE: The rear wiper operates in an intermittent mode located on the control lever. The control lever is located only. on the right side of the steering column. Rotate the switch upward past the first detent to activate the rear washer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE mirrors. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Metal rails/crossbars are offered by MOPAR威 accessories. See your authorized dealer. External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the maximum vehicle load capacity. CAUTION! • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 190 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 191 ▫ Electronic Vehicle Information Center (EVIC) 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 192 Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 䡵 Compass And Trip Computer — If Equipped . .
188 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Media Center 230 (REQ) — AM/FM Stereo 䡵 Media Center 730N/430/430N (RER/RBZ/ Radio And 6–Disc CD/DVD Changer RHB) CD/DVD/HDD/NAV — If Equipped . . . 241 (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . 222 ▫ Operating Instructions (Voice Command ▫ Operating Instructions - Radio Mode . . . . . . 222 System) — If Equipped . . . . . . . . . . . . . . . . 241 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play, DVD-Video) . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 256 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 258 ▫ List Button (CD Mode For MP3 Play) . . . . . . 261 ▫ Info Button (CD Mode For MP3 Play) . . . . . . 261 ▫ Uconnect™ Multimedia (Satellite Radio) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 262 䡵 Steering Wheel Audio Controls — If Equipped . 266 ▫ Radio Operation . . . . . . . . . . . . . . . . . .
190 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 — Air Outlet — Instrument Cluster — Storage Tray — Center Air Outlet — Radio 6 — Glove Compartment 7 — Climate Control 8 — Heated Seat Switch * 9 — Rear Park Assist Switch * 10 — Passenger Airbag Disable Light 11 — Hazard Warning Flasher 12 — Electronic Stability Program / Traction Control Switch * 13 — Cigar Lighter / Power Outlet 14 — Storage Bin * If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 191 INSTRUMENT CLUSTER 4
192 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The fuel gauge shows level of fuel in tank when ignition switch is in the ON/RUN position. 2. Fuel Door Reminder This symbol indicates the side of the vehicle where the fuel cap is located. 3. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealership for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.
194 UNDERSTANDING YOUR INSTRUMENT PANEL normal, turn the engine off immediately and call for 10. Electronic Stability Control (ESC) Activation/ service. Refer to “If Your Engine Overheats” in “What To Malfunction Indicator Light — If Equipped The “ESC Activation/Malfunction Indicator Do In Emergencies” for further information. Light” in the instrument cluster will come on 7. Speedometer when the ignition switch is turned to the Shows the vehicles speed. ON/RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 • Each time the ignition is turned to ON/RUN, the ESC continuous chime will sound to alert you to turn the system will be ON even if it was turned off previously. signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop 13.
196 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Continued operation with the Transmission Temperature Warning Light illuminated could cause the fluid to boil over, come in contact with hot engine or exhaust components causing a fire that may result in personal injury. 14. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 If brake failure is indicated, immediate repair is neces- unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light sary. inspected by an authorized dealer. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.
198 UNDERSTANDING YOUR INSTRUMENT PANEL the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned to ON/RUN and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 21. Oil Pressure Warning Light 19. Anti-Lock Brake (ABS) Light This light indicates low engine oil pressure. The This light monitors the Anti-Lock Brake System light should turn on momentarily when the engine (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime may stay on for as long as four seconds.
200 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Tachometer This gauge measures engine revolutions-per-minute (RPM x 1000). When the engine RPM are kept within the green area, you are driving the vehicle in a fuel efficient manner. Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 24. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 maintain correct tire pressure, even if under-inflation has tires or wheels on your vehicle, to ensure that the not reached the level to trigger illumination of the TPMS replacement or alternate tires and wheels allow the TPMS to continue to function properly. low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
202 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Odometer / Trip Odometer Display Area The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “Trip Odometer Button” for additional information. NOTE: U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL ECO / ECO-ON (Fuel Saver Indicator) — If Equipped The ECO-ON indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy. The ECO display will toggle between ECO and ECO-ON depending on driving habits and vehicle usage.
204 UNDERSTANDING YOUR INSTRUMENT PANEL ODOMETER button on the instrument cluster. To reset the ON/RUN position, before engine start. If the bulb the oil change indicator system (after performing the does not come on when turning the key from OFF to scheduled maintenance), refer to the following proce- ON/RUN, have the condition checked promptly. dure: Certain conditions such as a loose or missing gas cap, 1. Turn the ignition switch to the ON/RUN position. poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 205 29.
206 UNDERSTANDING YOUR INSTRUMENT PANEL Resetting the Trip Odometer 31. 4WD Indicator — If Equipped This light indicates the vehicle is in four-wheel Display the trip mileage that you want to reset, “Trip A” drive and 4LOCK. 4WD allows all four wheels to or “Trip B.” Then push and hold the button (approxireceive torque from the engine simultaneously. mately two seconds) until the display resets to 0. The odometer must be in Trip Mode to reset the trip odometer. COMPASS AND TRIP COMPUTER — IF EQUIPPED 30.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated temperature is displayed. Engine temperature can also affect the displayed temperature, therefore temperature readings are not updated when the vehicle is not moving.
208 UNDERSTANDING YOUR INSTRUMENT PANEL The compass/trip computer, when the appropriate con- Trip A ditions exist, will show the following messages in the Shows the total distance traveled for trip A since the last reset. odometer display: • Door Ajar (door) • Lift Gate Ajar (gATE) • Loose Fuel Cap (gASCAP) Trip B Shows the total distance traveled for trip B since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Compass/Temperature Display Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences and provide the most accurate compass heading.
210 UNDERSTANDING YOUR INSTRUMENT PANEL zone, press and release the CMTC reset button to increase 3. Release the CMTC reset button, then press and hold the variance one step. Repeat as necessary until the again for approximately 10 seconds, until the direction is displayed, with the CAL indicator on continuously in the desired variance is achieved. display. NOTE: The factory default zone is 8. During programming, the zone value will wrap around from zone 15 to 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 • Tire Pressure Monitor System (if equipped) • Personal Settings (Customer-Programmable Features) • Compass display • Outside temperature display • Trip computer functions • Uconnect™ gps system screens (if equipped) • Audio mode display The system allows the driver to select information by pressing the following buttons mounted on the steering This system conveniently allows the driver to select a wheel: variety of useful information by pressing the switches MENU B
212 UNDERSTANDING YOUR INSTRUMENT PANEL Press the FUNCTION SELECT button to accept a selection. Also, the FUNCTION SELECT button changes the current CD track being played (if equipped) when the EVIC is in the Compass/Temp/Audio screen. Electronic Vehicle Information Center (EVIC) Displays When the appropriate conditions exist, the EVIC displays the following messages.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 • Door(s) ajar (with a single chime if vehicle is in • Check TPM System (with a single chime). Refer to motion) “Tire Pressure Monitoring System” in “Starting And Operating”. • Liftgate ajar (with a single chime) • Check Gascap (refer to “Adding Fuel” in “Starting • Left front low pressure (with a single chime). Refer to And Operating”). “Tire Pressure Monitoring System” in “Starting And • Oil change required (with a single chime). Operating”.
214 UNDERSTANDING YOUR INSTRUMENT PANEL engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the MENU button. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the following procedure.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 history information will be erased, and the averaging will to a text display of LOW FUEL. This display will concontinue from the last fuel average reading before the tinue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the LOW reset. FUEL text and a new DTE value will display. • Distance To Empty (DTE) Shows the estimated distance that can be traveled with • Elapsed Time the fuel remaining in the tank.
216 UNDERSTANDING YOUR INSTRUMENT PANEL the FUNCTION SELECT button a second time within three seconds of resetting the currently displayed function. (Reset ALL will display during this three-second window). ECO (Fuel Saver Mode) — If Equipped The ECO message will display below the outside temperature in the EVIC display. This message will appear whenever you are driving in a fuel efficient manner.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: A good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Manual Compass Calibration If the compass appears erratic and the CAL indicator does not appear in the EVIC display, you must put the compass into the calibration mode manually as follows: 217 5.
218 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Magnetic materials should be kept away from 3. Press the SCROLL button until the “Compass Varithe top of the right rear quarter window. This is where ance” message and the last variance zone number displays in the EVIC. the compass sensor is located. 4. Press and release the FUNCTION SELECT button until the proper variance zone is selected according to the map. 5. Press and release the COMPASS button to exit.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Use the SCROLL button to display one of the following NEUTRAL position and the driver’s door is opened. To make your selection, press and release the FUNCTION choices: SELECT button until ON or OFF appears. Language When in this display you may select one of five lan- Remote Key Unlock guages for all display nomenclature, including the trip When Driver Door 1st Press is selected, only the driver’s functions and the navigation system (if equipped).
220 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Key Lock feature. To make your selection, press Turn Headlights On with Remote Key Unlock and release the FUNCTION SELECT button until ON or When this feature is selected, the headlights will activate and remain on for up to 90 seconds when the doors are OFF appears. unlocked with the RKE transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL Enable/Disable the Rear Park Assist System The Rear Park Assist system will scan for objects behind the vehicle when the transmission is in the REVERSE and the vehicle speed is less than 11 mph (18 km/h). The system can be enabled with turned ON or turned OFF through the EVIC, to make your selection, press and release the FUNCTION SELECT button.
222 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 230 (REQ) — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate. Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With Uconnect Phone” message will display on the radio screen.
224 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure INFO Button Press the INFO button for an RDS station (one with call 1. Press and hold the TIME button until the hours blink. letters displayed). The radio will return a Radio Text 2. Adjust the hours by turning the right side TUNE/ message broadcast from an FM station (FM mode only). SCROLL control knob. RW/FF 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be sePush the rotary TUNE/SCROLL control knob a third lected.
226 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk 16-Digit Character Display Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R & B Sports Talk Program Type Top 40 Weather 16-Digit Character Display Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will b
UNDERSTANDING YOUR INSTRUMENT PANEL • DVD Enter - When the disc is in DVD Menu mode, selecting DVD Enter will allow you to play the current highlighted selection. Use the remote control to scroll up and down the menu (if equipped). 227 • Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped).
228 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Home Clock - Pressing the SELECT button allows you to set the clock. Turn the TUNE/SCROLL control knob to adjust the hours and then press and turn the TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes. Audio Language — If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc).
UNDERSTANDING YOUR INSTRUMENT PANEL Audio DRC — If Equipped Selecting this item allows you to limit maximum audio dynamic range. The default is set to ⬙High,⬙ and under this setting, dialogues will play at 11 db higher than if the setting is ⬙Normal.⬙ 229 a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. AM and FM Buttons Press the buttons to select AM or FM mode.
230 UNDERSTANDING YOUR INSTRUMENT PANEL both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 NOTE: The ignition switch must be in the ON or ACC Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton position to operate the radio. with the corresponding number (1-6) where the LOAD Button — Loading Compact Disc(s) CD was loaded and the disc will unload and Press the LOAD button and the pushbutton with the move to the entrance for easy removal.
232 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD MODE) Notes On Playing MP3/WMA Files Press the SCAN button to scan through each track on the The radio can play MP3/WMA files; however, acceptable CD currently playing. MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the TIME Button (CD MODE) following restrictions. Press this button to change the display from a large CD playing time display to a small CD playing time display.
UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of directory levels: 8 • Maximum number of files: 255 233 If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. Supported MP3/WMA File Formats The radio will recognize only files with the *.MP3/WMA extension as MP3/WMA files. Non-MP3/WMA files • Maximum number of characters in file/folder names: named with the *.
234 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 WMA Specification Sampling Frequency (kHz) Bit Rate (kbps) WMA 44.1 and 48 48, 64, 96, 128, 160, 192 VBR Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 160, 128, 144, 112, 96, 80, 64, 56, 48 Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium.
UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files).
236 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. Operating Instructions — Voice Command System (If Equipped) For the radio, Refer to “Voice Command” in the Uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL Macrovision This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. 237 NOTE: Sirius service is not available in Hawaii and has limited coverage in Alaska.
238 UNDERSTANDING YOUR INSTRUMENT PANEL placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as To access the ESN/SID, refer to the following steps: bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly ESN/SID Access With the ignition switch in the ON/RUN or ACC posi- on or above the antenna.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Operating Instructions - Uconnect™ Multimedia (Satellite) Mode INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if availNOTE: The ignition switch must be in the ON/RUN or able). Also, pressing and holding the INFO button for an ACC position to operate the radio.
240 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory. The channels stored in SET 2 memory can be selected by pressing the pushbutton twice.
242 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (SALES CODE RES) Operating Instructions — Radio Mode NOTE: The radio sales code is located on the lower right NOTE: The ignition switch must be in the ON or ACC side of the radio faceplate. position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. 243 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones. Press the buttons to select either AM or FM mode. Push the rotary TUNE/SCROLL control knob a third SET/RND Button — To Set the Pushbutton time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
246 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate Random Play. This feature plays the selections on the CD and MP3 modes. compact disc in random order to provide an interesting TIME Button change of pace. Press this button to change the display from a large CD playing time display to a small CD playing time display.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) • Maximum number of characters in file/folder names: The medium formats supported by the radio are ISO 9660 • Level 1: 12 (including a separator ⬙.⬙ and a threeLevel 1 and Level 2 and includes the Joliet extension. character extension) When reading discs recorded using formats other than • Level 2: 31 (including a separator ⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rate. MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.
250 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. MEDIA CENTER 130 WITH SATELLITE RADIO (SALES CODE RES+RSC) NOTE: The radio sales code is located on the lower right side of the radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 SEEK Buttons Press and release the SEEK buttons to search for the next NOTE: The ignition switch must be in the ON or ACC listenable station in AM/FM mode. Press the right switch position to operate the radio. to seek up and the left switch to seek down. The radio Power Switch/Volume Control (Rotary) will remain tuned to the new station until you make Push the ON/VOLUME control knob to turn on the another selection. Holding either button will bypass radio.
252 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature SCROLL control knob. Press the TUNE/SCROLL control (if equipped). Refer to “Uconnect™ Phone” in “Under- knob to save time change. standing The Features If Your Vehicle”. 5. To exit, press any button/knob or wait five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. 253 Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
254 UNDERSTANDING YOUR INSTRUMENT PANEL or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 By pressing the SEEK button when the Music Type icon is AM/FM Button displayed, the radio will be tuned to the next frequency Press the button to select either AM or FM mode. station with the same selected Music Type name. The SET/RND Button — To Set the Pushbutton Music Type function only operates when in the FM mode.
256 UNDERSTANDING YOUR INSTRUMENT PANEL and 12 FM stations to be stored into pushbutton memory. • This radio is capable of playing compact discs (CD), The stations stored in SET 2 memory can be selected by recordable compact discs (CD-R), rewritable compact pressing the pushbutton twice. discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Every time a preset button is used, a corresponding Inserting Compact Disc(s) button number will display.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
258 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. AM/FM Button Press the button to select either AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of • Maximum number of folders. (The radio display of file multisession for CD audio or MP3 playback may result in names and folder names is limited. For large numbers longer disc loading times. of files and/or folders, the radio may be unable to display the file name and folder name and will assign Supported MP3 File Formats a number instead.
260 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds.
262 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is OFF). Uconnect™ Multimedia (Satellite Radio) — If Equipped Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio.
UNDERSTANDING YOUR INSTRUMENT PANEL using the TUNE/SCROLL control knob until Sirius ID is selected. Press the TUNE/SCROLL control knob and the Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen. 263 Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle.
264 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 If a preset button is activated while in the Music Type You may add a second channel to each pushbutton by (Program Type) mode, the Music Type mode will be repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display exited and the radio will tune to the preset channel. window. Each button can be set for SET 1 and SET 2.
266 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch will increase the volume, and pressing the bottom of the switch will decrease the volume.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Press the top of the switch once to go to the next track on the CD. Press the bottom of the switch once to go to the beginning of the current track or to the beginning of the previous track, if it is within one second after the current track begins to play. 267 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4.
268 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND MOBILE PHONES Manual Heating and Air Conditioning Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position. There are seven blower speeds. Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Panel Air is directed through the outlets in the instrument Air is directed through the floor outlets with a small amount flowing through the defrost and side panel. These outlets can be adjusted to direct airflow. window demist outlets. NOTE: The center instrument panel outlets can be aimed so that they are directed toward the rear seat Mix Air is directed through the floor, defrost, and side passengers for maximum airflow to the rear. window demist outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 NOTE: NOTE: • The air conditioning compressor operates in Mix, • Continuous use of the recirculation mode may make Defrost, or a blend of these modes, even if the Air the inside air stuffy and window fogging may occur. Conditioning (A/C) button is not pressed. This dehuExtended use of this mode is not recommended. midifies the air to help dry the windshield.
272 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Control Automatic Temperature Control (ATC) — Press this button to engage the Air Con- If Equipped ditioning. A light will illuminate when the Air Conditioning System is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures while rotating right into the red area indicates warmer temperatures. NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting 1. Turn the Mode Control knob (on the right) and the the “O” (OFF) position on the blower control stops the Blower Control knob (on the left) to AUTO. system completely and closes the outside air intake. NOTE: The AUTO position performs best for front seat The recommended setting for maximum comfort is 72°F occupants only.
274 UNDERSTANDING YOUR INSTRUMENT PANEL • If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce airflow to the condenser, reducing air conditioning performance.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 4
276 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to • Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets. • Panel Air is directed through the outlets in the instrument • Mix Air is directed through the floor, defrost, and side panel. These outlets can be adjusted to direct airflow.
UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn OFF the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
278 UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into Recirculation Mode at this time.
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather. NOTE: Recirculate without A/C should not be used for long periods as fogging may occur.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 285 ▫ Brake/Transmission Interlock System . . . . . . 289 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 285 ▫ Brake/Transmission Interlock Manual Override . . . . . . . . . . . . . . . . . . . . . . . . . . 290 ▫ Extreme Cold Weather (Below –20°F Or –29°C) . . . . . . . . . . . . . . . . 286 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . 286 ▫ After Starting . . . . . . . . . . . . . .
282 STARTING AND OPERATING 䡵 Four-Wheel Drive Operation — If Equipped . . 300 ▫ Electronic Roll Mitigation (ERM) . . . . . . . . . 311 ▫ MP 143 Single-Speed Part-Time Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 300 ▫ Electronic Stability Control (ESC) . . . . . . . . . 312 ▫ Shifting Procedure – Electronically Shifted Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 301 䡵 On-Road Driving Tips . . . . . . . . . . . . . . . . . . 302 䡵 Power Steering . . . . . . . . . . . . .
STARTING AND OPERATING 283 ▫ Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . 328 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 346 ▫ Compact Spare Tire – If Equipped . . . . . . . . 328 ▫ 3.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . 346 ▫ Limited-Use Spare – If Equipped . . . . . . . . . 329 ▫ 4.0L Engine . . . . . . . . . . . . . . . . . . . . . . . . 346 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 330 ▫ Reformulated Gasoline . . . . . . .
284 STARTING AND OPERATING 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . 353 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 369 ▫ Certification Label . . . . . . . . . . . . . . . . . . . 353 䡵 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 355 ▫ Towing This Vehicle ▫ Common Towing Definitions . . . . . . . . . . . . 355 Behind Another Vehicle . . . . . . . . . . . . .
STARTING AND OPERATING 285 STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both NOTE: Normal starting of either a cold or a warm inside and outside mirrors, and fasten your seat belts. engine is obtained without pumping or pressing the accelerator pedal. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
286 STARTING AND OPERATING Extreme Cold Weather (below –20°F or –29°C) To ensure reliable starting at these temperatures, the use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails to Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury.
STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accelerator pedal pressed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly.
288 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine, and permits CAUTION! quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a Damage to the transmission may occur if the followgrounded three-wire extension cord.
STARTING AND OPERATING WARNING! • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in REVERSE. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly on the brake pedal. • Never leave children alone in a vehicle.
290 STARTING AND OPERATING Brake/Transmission Interlock Manual Override Your vehicle may be equipped with a shift lock manual override. The manual override may be used in the event that the shift lever should fail to move from PARK with the key in the ON position and the brake pedal pressed. To operate the shift lock manual override, perform the following steps: 1. Turn the key to the ON position, but do not start the engine. 2. Firmly set the parking brake. 3.
STARTING AND OPERATING 291 Four–Speed Automatic Transmission – 3.7L Engine NOTE: Under extreme cold temperatures (-10°F (-23°C) and when in DRIVE, transmission operation may be briefly limited to only second gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level. Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped.
292 STARTING AND OPERATING Never use PARK while the vehicle is in motion. Apply REVERSE the parking brake when leaving the vehicle in this range. This range is for moving the vehicle backward. Use only Always apply the parking brake first, then place the shift after the vehicle has come to a complete stop. lever in the PARK position. NEUTRAL This range is used when vehicle is standing for proWARNING! longed periods with engine running.
STARTING AND OPERATING 293 2 (Second) • vehicle speed is above approximately 30 mph This range is used for moderate grades and to assist (48 km/h) braking on dry pavement or in mud and snow. Begins at • the TOW/HAUL button has not been activated a stop in low gear with automatic upshift to second gear. The transmission will downshift from OVERDRIVE to Will not shift into third gear. DRIVE if the accelerator pedal is fully pressed at vehicle 1 (First) speeds above approximately 35 mph (56 km/h).
294 STARTING AND OPERATING NOTE: The TOW/HAUL mode locks out Overdrive. normal operation. If the TOW/HAUL mode is desired, the switch must be pressed each time the engine is started. Transmission Limp Home Mode Transmission function is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the Transmission Limp Home Mode will be engaged. In this mode, the transmission will remain in second gear in any forward driving range.
STARTING AND OPERATING 295 self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal If the problem is no longer detected, the transmission will condition and precision shifts will develop within a few return to normal operation. If the problem persists, hundred miles/kilometers. PARK, REVERSE, and NEUTRAL will continue to operate. Only second gear range will operate in the DRIVE position.
296 STARTING AND OPERATING Gear Ranges NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. If there is a need to restart the engine, be sure to cycle the key to the LOCK position before restarting. Transmission gear engagement may be delayed after restarting the engine if the key is not cycled to the LOCK position first.
STARTING AND OPERATING 297 the transmission into third gear, the transmission will NEUTRAL This range is used when vehicle is standing for pro- never shift above third gear, but can shift down into longed periods with engine running. Engine may be second gear or first gear, when needed. started in this range. Set the parking brake if you must WARNING! leave the vehicle.
298 STARTING AND OPERATING Overdrive Operation The overdrive automatic transmission contains an electronically controlled fifth gear (OVERDRIVE). The transmission will automatically shift from fourth gear to OVERDRIVE if the following conditions are present: • the shift lever is in DRIVE risen to a suitable level. Refer to the “Note” under “Torque Converter Clutch” later in this section. During cold temperature operation, you may notice delayed upshifts depending on engine and transmission temperature.
STARTING AND OPERATING 299 To reset the transmission, use the following procedure: Torque Converter Clutch A feature designed to improve fuel economy has been 1. Stop the vehicle. included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati2. Move the shift lever to the PARK position. cally at a calibrated speed at light throttle. It engages at 3. Turn the engine off and turn the key to the LOCK higher speeds under heavier acceleration.
300 STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED MP 143 Single-Speed Part-Time Transfer Case The electronically shifted transfer case provides two mode positions: • Two-wheel drive high range (2WD) Operating Information/Precautions The transfer case is operated by the transfer case switch • Four-wheel drive high range (4WD LOCK) (located on the center console).
STARTING AND OPERATING CAUTION! • Driving in the 4WD LOCK position on dry hard surfaced roads may cause increased tire wear and damage to the driveline components. • Do not attempt to make a shift while only the front or rear wheels are spinning. Shifting while only the front or rear wheels are spinning can cause damage to the transfer case. Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel.
302 STARTING AND OPERATING must be in the ON position with the engine either characteristics give them a higher center of gravity than RUNNING or OFF. This shift cannot be completed if the ordinary cars. key is in the ACC position. An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems.
STARTING AND OPERATING If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. NOTE: • Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system.
304 STARTING AND OPERATING apparent, and/or the system is not functioning as antici- If necessary, add fluid to restore to the proper indicated pated. Coordinate inspection efforts through an autho- level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine rized dealer. Parts” in “Maintaining Your Vehicle” for further CAUTION! information.
STARTING AND OPERATING 305 NOTE: • When the parking brake is applied and the transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
306 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. • Do not leave the key in the ignition.
STARTING AND OPERATING 307 computer to modulate hydraulic pressure, to prevent The ABS pump motor runs during the self-test at 12 mph wheel lock-up and help avoid skidding on slippery (20 km/h) and during an ABS stop. The pump motor makes a low humming noise during operation, which is surfaces. normal. All vehicle wheels and tires must be the same size and type, and tires must be properly inflated, to produce WARNING! accurate signals for the computer.
308 STARTING AND OPERATING WARNING! (Continued) • The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others.
STARTING AND OPERATING 309 build up between the tire tread and the road. This Anti-Lock Brake System (ABS) hydroplaning action can cause loss of traction, braking This system aids the driver in maintaining vehicle control ability, and control. under adverse braking conditions.
310 STARTING AND OPERATING Traction Control System (TCS) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
STARTING AND OPERATING WARNING! The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
312 STARTING AND OPERATING Electronic Stability Control (ESC) This system enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
STARTING AND OPERATING WARNING! The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
314 STARTING AND OPERATING traction. To turn ESC on again, momentarily press the Light” comes on continuously with the engine running, a “ESC Off” switch. This will restore the normal “ESC On” malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the mode of operation.
STARTING AND OPERATING 315 NOTE: TIRE SAFETY INFORMATION • The “ESC Activation/Malfunction Indicator Light” Tire Markings and the “ESC OFF Indicator Light” come on momentarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESC system will be ON even if it was turned off previously. • The ESC system will make buzzing or clicking sounds when it is active.
316 STARTING AND OPERATING NOTE: • LT (Light Truck) - Metric tire sizing is based on U.S. • P (Passenger) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric design standards. P-Metric tires have the letter “P” tires is the same as for P-Metric tires except for the molded into the sidewall preceding the size designaletters “LT” that are molded into the sidewall precedtion. Example: P215/65R15 95H. ing the size designation. Example: LT235/85R16.
STARTING AND OPERATING 317 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
318 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. 319 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
320 STARTING AND OPERATING Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
STARTING AND OPERATING Tire Loading and Tire Pressure 321 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
322 STARTING AND OPERATING This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section.
STARTING AND OPERATING 323 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcusengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity. For example, if “XXX” and number and size of occupants.
324 STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
326 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
STARTING AND OPERATING Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall.
328 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision.
STARTING AND OPERATING 329 WARNING! CAUTION! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
330 STARTING AND OPERATING WARNING! WARNING! The limited-use spare tires are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than 50 mph (80 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited-use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING 331 Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! 1 — Worn Tire 2 — New Tire Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death.
332 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed. (Refer to the paragraph on “Tread Wear Indicators”). Refer to the “Tire and Loading Information” placard for the size designation of your tire.
STARTING AND OPERATING WARNING! (Continued) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. TIRE CHAINS Use “Class S” chains or other traction aids that meet SAE Type “S” specifications. NOTE: Chains must be the proper size for the vehicle as recommended by the chain manufacturer.
334 STARTING AND OPERATING CAUTION! (Continued) CAUTION! • Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed of the chain manufacturer if different than the speed recommended by the manufacturer. Do not use tire chains on vehicles equipped with tires other than P235/65R17 and P225/75R16 tires.
STARTING AND OPERATING CAUTION! 335 The suggested rotation method is the “forward-cross” shown in the following diagram. Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Tire rotation schedule should be followed to balance tire wear. Refer to the “Maintenance Schedule” for the proper maintenance intervals. More frequent rotation is permissible if desired.
336 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C).
STARTING AND OPERATING For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 33 psi (227 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 28 psi (193 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 24 psi (165 kPa). This tire pressure is low enough to turn ON the “Tire Pressure Monitoring Telltale Light.
338 STARTING AND OPERATING NOTE: • Seasonal temperature changes will affect tire pressure, • The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance, or to provide warning of a tire the tire. failure or condition. Base System • The TPMS should not be used as a tire pressure gauge The Tire Pressure Monitor System (TPMS) uses wireless while adjusting your tire pressure.
STARTING AND OPERATING The matching full-size spare wheel and tire assembly (if equipped) has a tire pressure monitoring sensor. The matching full-size spare can be used in place of any of the four road tires. The TPMS will only monitor the pressure in the full-size spare when it is used in place of a road tire. Otherwise, a spare with a pressure below the lowpressure limit will not cause the “Tire Pressure Monitoring Telltale Light” to illuminate or the chime to sound.
340 STARTING AND OPERATING 3. Lots of snow or ice around the wheels or wheel Vehicles with Compact Spare housings. 1. The compact spare tire does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor 4. Using tire chains on the vehicle. the pressure in the compact spare tire. 5. Using wheels/tires not equipped with TPMS sensors. 2. If you install the compact spare tire in place of a road Vehicles with Full-Size Spare tire that has a pressure below the low-pressure warning 1.
STARTING AND OPERATING 341 Telltale Light” will turn off, as long as no tire pressure is • Three Trigger Modules (mounted in three of the four below the low-pressure warning limit in any of the four wheel-wells) active road tires. The vehicle may need to be driven for • Various Tire Pressure Monitoring System messages, up to 20 minutes above 15 mph (25 km/h) in order for the which display in the Electronic Vehicle Information TPMS to receive this information.
342 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing.
STARTING AND OPERATING 343 If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “Tire Pressure Monitoring Telltale Light” will no longer flash, and the ⬙CHECK TPM SYSTEM⬙ message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1.
344 STARTING AND OPERATING Vehicles with Full-Size Spare Vehicles with Compact Spare 1. The matching full size spare wheel and tire assembly 1. The compact spare tire does not have a tire pressure has a tire pressure monitoring sensor that can be moni- monitoring sensor. Therefore, the TPMS will not monitor tored by the TPMS. the pressure in the compact spare tire. 2.
STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will sound, the “TPMS Telltale Light” will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a ⬙CHECK TPM SYSTEM⬙ message for three seconds and then display dashes (- -) in place of the pressure value. 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically.
346 STARTING AND OPERATING FUEL REQUIREMENTS 3.7L Engine All engines are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. 4.0L Engine The 4.
STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as reformulated gasoline. Reformulated gasolines contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components.
348 STARTING AND OPERATING If a Non-FFV vehicle is inadvertently fueled with E-85 MMT In Gasoline fuel, the engine will have some or all of these symptoms: MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline • operate in a lean mode blended with MMT provides no performance advantage • OBD II “Malfunction Indicator Light” on beyond gasoline of the same octane number without MMT.
STARTING AND OPERATING Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
350 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 351 CAUTION! Fuel Filler Cap • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors escaping from the system. • A poorly fitting gas cap may cause the MIL to turn on.
352 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and may cause the MIL to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING 353 Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle Certification Label including driver, passengers, vehicle, options, trailer As required by National Highway Traffic Safety Admintongue weight, and cargo. The label also specifies maxiistration regulations, your vehicle has a certification label mum capacities of front and rear axle systems (GAWR). affixed to the driver’s side door or B-Pillar.
354 STARTING AND OPERATING Each axle’s GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires, or wheels). Heavier axles or suspension components, sometimes specified by purchasers for increased durability, does not necessarily increase the vehicle’s GVWR.
STARTING AND OPERATING the front or rear axles has been exceeded, but the total load is within the specified GVWR. If so, weight must be shifted from front to rear, or rear to front, as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving.
356 STARTING AND OPERATING exceed the GVWR. Refer to “Vehicle Loading/Vehicle Gross Combination Weight Rating (GCWR) Certification Label” in Starting and Operating” for fur- The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. ther information.
STARTING AND OPERATING Tongue Weight The tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal Area The frontal area is the maximum height multiplied by the maximum width of the front of a trailer.
358 STARTING AND OPERATING WARNING! • An improperly adjusted weight distributing hitch system may reduce handling, stability, and braking performance and could result in a collision. • Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recreational vehicle dealer for additional information.
STARTING AND OPERATING 359 5 With Weight-Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (Incorrect)
360 STARTING AND OPERATING Trailer Hitch Classification Your vehicle is capable of towing trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional trailer tow prep package. See your authorized dealer for package content.
STARTING AND OPERATING 361 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Model Frontal Area Max. GTW Max. Tongue Wt. Transmission (Gross Trailer Wt) (See Note) 3.7L/Automatic 4x2 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.7L/Automatic 4x4 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 4.0L/Automatic 4x2 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 4.
362 STARTING AND OPERATING When Towing Trailers with Gross Trailer Weight (GTW) between 3,500 Lbs (1 588 kg) and 5,000 Lbs (2 268 kg) The following chart provides maximum trailer weight ratings towable for the following engine/transmission combinations, ONLY if using a weight distributing hitch. Engine/Transmission Model Frontal Area Max. GTW (Gross Trailer Wt) 5,000 lbs (2 268 kg) Max. Tongue Wt. (See Note) 500 lbs (227 kg) 3.7L/Automatic w/Trailer 4x2 64 sq ft (5.94 sq m) Tow Package 3.
STARTING AND OPERATING 363 Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely from side-toside which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions.
364 STARTING AND OPERATING Consider the following items when computing the Towing Requirements To promote proper break-in of your new vehicle driveweight on the rear axle of the vehicle: train components the following guidelines are recom• The tongue weight of the trailer. mended: • The weight of any other type of cargo or equipment CAUTION! put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
STARTING AND OPERATING WARNING! 365 WARNING! (Continued) Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision.
366 STARTING AND OPERATING WARNING! (Continued) 3. GAWR 4. Tongue weight rating for the trailer hitch utilized. (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements – Tires − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires – General Information” in “Starting and Operating” for the proper inspection procedure.
STARTING AND OPERATING − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
368 STARTING AND OPERATING Towing Requirements – Trailer Lights and Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The trailer tow package may include a four-pin and seven-pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness.
STARTING AND OPERATING 369 Towing Tips Before setting out on a trip, practice turning, stopping and backing up the trailer in an area away from heavy traffic. Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “TOW/ HAUL” button (if equipped) or a lower gear range should be selected.
370 STARTING AND OPERATING 45 minutes of continuous operation. Refer to “Mainte- Cooling System To reduce potential for engine and transmission overnance Schedule” for the proper maintenance intervals.
STARTING AND OPERATING 371 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
372 STARTING AND OPERATING Recreational Towing — Two-Wheel Drive Models Recreational towing is allowed if the rear wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 6. Install a suitable clamping device, designed for towing, to secure the front wheels in the straight position. 7. Disconnect the negative battery cable and secure it away from the battery post. Flat towing (with all four wheels on the ground) is 1.
STARTING AND OPERATING The parking brake must be firmly engaged and the wheels chocked during driveshaft removal and installation. The parking brake must remain engaged unless the vehicle is securely and properly connected to the tow vehicle, or the driveshaft is completely reinstalled. See your authorized dealer for proper driveshaft removal and reinstallation procedures, including flange orientation/alignment, use of thread-locking compound, proper bolt torque specifications, etc.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 376 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . . 383 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 376 ▫ Preparations For Jump-Start . . . . . . . . . . . . . 384 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 377 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . 385 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 378 䡵 Towing A Disabled Vehicle . . . .
376 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning Flasher switch is located on the In any of the following situations, you can reduce the lower switch bank below the climate controls. potential for overheating your engine by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — slow down.
WHAT TO DO IN EMERGENCIES 377 NOTE: There are steps that you can take to slow down JACKING AND TIRE CHANGING an impending overheat condition: • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat. • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.
378 WHAT TO DO IN EMERGENCIES Jack Location Spare Tire Removal The scissor-type jack and tire changing tools are located Fit the jack handle extension over the drive nut. Use the in the left rear trim panel behind the second row seat. lug wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow you to pull the tire out from under the vehicle.
WHAT TO DO IN EMERGENCIES 379 CAUTION! WARNING! The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and they can damage the winch. Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. When the spare is clear, tilt the retainer at the end of the 2.
380 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.
WHAT TO DO IN EMERGENCIES 381 1. Remove spare tire. 2. Remove jack and tools from mounting bracket. Assemble the tools by connecting the driver to the extension, and then to the lug wrench. 3. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 4. Locate the jack as shown. For the front tires, place it (rearward) of the notch on the body weld seam behind wheel to be changed.
382 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause a collision. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. Rear Jacking Location 7. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts.
WHAT TO DO IN EMERGENCIES 383 wheel nut tightness is 95 ft lbs (130 N·m). If in doubt pack. Jump-starting can be dangerous if done improperly about the correct tightness, have them checked with a so please follow the procedures in this section carefully. torque wrench by your authorized dealer or at a service NOTE: When using a portable battery booster pack station. follow the manufacturer’s operating instructions and precautions. 10. Lower the jack to its fully closed position.
384 WHAT TO DO IN EMERGENCIES Preparations for Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades.
WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure WARNING! Failure to follow this procedure could result in personal injury or property damage due to battery explosion.
386 WHAT TO DO IN EMERGENCIES WARNING! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle.
WHAT TO DO IN EMERGENCIES 387 may also be towed as described under “Recreational TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled Towing” in the “Starting and Operating” section. vehicle using a commercial wrecker service.
388 WHAT TO DO IN EMERGENCIES If you must use the accessories (wipers, defrosters, etc.) Towing Without the Ignition Key Fob while being towed, the ignition must be in the ON/RUN Special care must be taken when the vehicle is towed with the ignition in the LOCK position. The only apposition, not the ACC position. proved method of towing without the ignition key is If the vehicle’s battery is discharged, see “Brake/ with a flatbed truck.
WHAT TO DO IN EMERGENCIES 389 CAUTION! WARNING! Towing faster than 30 mph (48 km/h) or farther than 15 miles (24 km) with rear wheels on the ground can cause severe damage to the transmission. Such damage is not covered by the New Vehicle Limited Warranty. If the driveshaft is removed, the vehicle can roll even if the transmission is in PARK, which could cause serious injury or death.
390 WHAT TO DO IN EMERGENCIES Four-Wheel Drive Vehicles The manufacturer requires towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly. CAUTION! • Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.7L . . . . . . . . . . . . . 393 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 398 䡵 Engine Compartment — 4.0L . . . . . . . . . . . . . 394 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 399 䡵 Onboard Diagnostic System — OBD II . . . . . . 395 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 402 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 395 ▫ Engine Air Cleaner Filter . . . . . . . . . . .
392 MAINTAINING YOUR VEHICLE ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 407 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 431 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 409 ▫ Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 431 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ Left Front Turn Signal . . . . . . . . . . . . . . . . . 431 ▫ Automatic Transmission . . . . . . . . . . . . . . . 417 ▫ Right Front Turn Signal . . . .
MAINTAINING YOUR VEHICLE 393 ENGINE COMPARTMENT — 3.
394 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 4.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
396 MAINTAINING YOUR VEHICLE For states that require an Inspection and Mainte“Electronic Vehicle Information Center (EVIC)” in “Unnance (I/M), this check verifies the “Malfunction derstanding Your Instrument Panel” for further informaIndicator Light (MIL)” is functioning and is not tion. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tight- on when the engine is running, and that the OBD II system is ready for testing. ened.
MAINTAINING YOUR VEHICLE 397 2. If you crank or start the engine, you will have to start If your OBD II system is not ready, you should see your this test over. authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, 3.
398 MAINTAINING YOUR VEHICLE REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance. Damage or failures caused by the use of non-MOPAR威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty. DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.
MAINTAINING YOUR VEHICLE CAUTION! • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance. Immediately have potential malfunctions examined by an authorized Chrysler Group LLC dealership or qualified repair center. • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals.
400 MAINTAINING YOUR VEHICLE CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. manufacturer recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity – 3.7L Engine SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap shows the recommended engine oil viscosity for your vehicle. 401 Synthetic Engine Oils You may use synthetic engine oils provided the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed.
402 MAINTAINING YOUR VEHICLE Engine Oil Filter Engine Air Cleaner Filter The engine oil filter should be replaced with a new filter Refer to “Maintenance Schedule” for further information. at every engine oil change. NOTE: For best access to the oil filter, a drive on hoist should be used instead of a chassis hoist (3.7L Only). Engine Oil Filter Selection All of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine air cleaner filters are a high quality filter and are recommended. Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required.
404 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Warranty Information Book, located on the DVD, for further warranty information. • The air conditioning system contains refrigerant under high pressure.
406 MAINTAINING YOUR VEHICLE hood latching components to ensure proper function. Avoid using the wiper blades to remove frost or ice from When performing other underhood services, the hood the windshield. Keep the blade rubber out of contact with latch, release mechanism and safety catch should be petroleum products such as engine oil, gasoline, etc. cleaned and lubricated.
MAINTAINING YOUR VEHICLE WARNING! Commercial windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
408 MAINTAINING YOUR VEHICLE CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE 409 To minimize the possibility of catalytic converter dam- Cooling System age: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
410 MAINTAINING YOUR VEHICLE garden hose vertically down the face of the A/C con- Cooling System – Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty and contains a denser (if equipped) or the back of the radiator core. considerable amount of sediment, clean and flush with Check the engine cooling system hoses for brittle rubber, reliable cooling system cleaner. Follow with a thorough cracking, tears, cuts, and tightness of the connection at rinsing to remove all deposits and chemicals.
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of engine coolant (antifreeze) other than the specified HOAT engine coolant (antifreeze) may result in decreased corrosion protection and engine damage. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol based engine coolant (antifreeze) products.
412 MAINTAINING YOUR VEHICLE • Mix a minimum solution of 50% HOAT engine coolant and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. Cooling System Pressure Cap The cap must be fully tightened to prevent the loss of engine coolant (antifreeze) and to ensure that the engine coolant (antifreeze) will return to the radiator from the coolant reserve tank.
MAINTAINING YOUR VEHICLE WARNING! (Continued) • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result. Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community.
414 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are required, or if the level in the recovery bottle does not NOTE: When the vehicle is stopped after a few miles/ drop when the engine cools, the cooling system should kilometers of operation, you may observe vapor coming be pressure tested for leaks. from the front of the engine compartment.
MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to “Maintenance Schedule” for further information. WARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.
416 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also labeled on the original factory installed hydraulic master cylinder reservoir.
MAINTAINING YOUR VEHICLE WARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Automatic Transmission Fluid Level Check Your vehicle is equipped with a capped transmission oil fill tube. It is sealed and should not be tampered with. Your authorized dealer has the proper tools to ensure that the fluid level is set properly.
418 MAINTAINING YOUR VEHICLE detecting fluid leaks. The use of transmission sealers should be avoided as they may adversely affect seals. CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. Transfer Case Fluid Level Check The fluid level should be to the bottom edge of the fill hole (1) when the vehicle is in a level position.
MAINTAINING YOUR VEHICLE 419 the vehicle. Fluid changes are not necessary unless the Draining Fluid First remove the fill plug (1), then the drain plug (2). fluid becomes contaminated with water. Change the fluid Recommended tightening torque for the drain and fill immediately if contaminated with water. plugs is 15–25 ft lbs (20–34 N·m). Front/Rear Axle Fluid For normal service, periodic fluid level checks are not CAUTION! required.
420 MAINTAINING YOUR VEHICLE hot or cold weather and other extreme conditions will Adding Fluid Add lubricant only at the fill hole and only to the level have an adverse effect on paint, metal trim, and underbody protection. specified above. The following maintenance recommendations will enable Selection of Lubricant Use only manufacturer’s recommended fluid.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove.
422 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, Wheel and Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and chrome-plated wheels, should be cleaned regularly with considered the responsibility of the owner. a mild soap and water to prevent corrosion.
MAINTAINING YOUR VEHICLE 423 • For tough stains, apply MOPAR威 Total Clean or if absolutely necessary. Do not use harsh cleaners or equivalent, or a mild soap solution to a clean, damp Armor All威. Use MOPAR威 Total Clean or equivalent to cloth and remove the stain. Use a fresh, damp towel to clean vinyl upholstery. remove soap residue. • For grease stains, apply MOPAR威 Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue.
424 MAINTAINING YOUR VEHICLE When cleaning the rear view mirror, spray cleaner on the If the seat belts need cleaning, use MOPAR威 Total Clean towel or rag that you are using. Do not spray cleaner or equivalent, a mild soap solution, or lukewarm water. Do not remove the seat belts from the vehicle to wash directly on the mirror. them.
MAINTAINING YOUR VEHICLE Cav- Cartridge ity Fuse J4 25 Amp Natural J5 25 Amp Natural J6 40 Amp Green Totally Integrated Power Module (TIPM) Cav- Cartridge ity Fuse J1 — J2 30 Amp Pink J3 — MiniFuse J7 30 Amp Pink J8 40 Amp Green — — 30 Amp Pink Description — Transfer Case, Pwr Liftgate Module — J9 J10 J11 MiniFuse 425 Description Driver Door Node Passenger Door Node Antilock Brakes Pump, Stability Control System Antilock Brakes Valve, Stability Control System Power Seat – If Equipped — — Anti–T
426 MAINTAINING YOUR VEHICLE Cav- Cartridge ity Fuse J12 — J13 60 Amp Yellow J14 40 Amp Green J15 40 Amp Green J17 40 Amp Green J18 20 Amp Blue J19 60 Amp Yellow J20 30 Amp Pink MiniFuse Description — Ignition Off Draw – Main Rear Defroster Front Blower Starter Solenoid Powertrain Control Module Radiator Fan Front Wiper Cav- Cartridge Miniity Fuse Fuse J21 20 Amp Blue J22 25 Amp Natural M1 15 Amp Blue M2 20 Amp Yellow M3 20 Amp Yellow M4 10 Amp Red M5 25 Amp Natural M6 20 Amp Yellow Description Front/
MAINTAINING YOUR VEHICLE Cav- Cartridge Miniity Fuse Fuse M7 20 Amp Yellow M8 20 Amp Yellow M9 — M10 15 Amp Blue M11 10 Amp Red M12 30 Amp Green Description Cigar Lighter Front Heated Seat – If Equipped — Ignition Off Draw – Video System, Satellite Radio, DVD, HandsFree Module, Antenna, Universal Garage Door Opener, Vanity Lamp Ignition Off Draw – Climate Control System, MW SENSR, Underhood Lamp Radio, Amplifier Cav- Cartridge Miniity Fuse Fuse M13 20 Amp Yellow M14 M15 M16 20 Amp Yellow 20 Amp Ye
428 MAINTAINING YOUR VEHICLE Cav- Cartridge Miniity Fuse Fuse M17 15 Amp Blue M18 15 Amp Blue M19 25 Amp Natural 15 Amp Blue M20 M21 M22 20 Amp Yellow 10 Amp Red Description Left Front Park & Side Marker/Left Tail/ License/Park Lamp Right Front Park & Side Marker/Right Tail/Park/Run Lamp Automatic Shutdown #1 and #2 Instrument Cluster Interior Light, Switch Bank, Steering Column Module Automatic Shutdown #3 Right Horn Cav- Cartridge Miniity Fuse Fuse M23 10 Amp Red M24 25 Amp Natural M25 20 Amp Ye
MAINTAINING YOUR VEHICLE Cav- Cartridge Miniity Fuse Fuse M30 15 Amp Blue M31 M32 M33 20 Amp Yellow 10 Amp Red 10 Amp Red Description Rear Wiper Module, Power Folding Mirror – If Equipped, Diagnostic Link Back-Up Lamps Cav- Cartridge Miniity Fuse Fuse M34 10 Amp Red Airbag Module Powertrain Control Module M35 M36 M37 M38 10 Amp Red — 10 Amp Red 25 Amp Natural 429 Description Park Assist/Rear Camera, Climate Control System Module, Headlamp Wash, Compass, IR Sensor, Relay Diesel Cabin Heater, Radi
430 MAINTAINING YOUR VEHICLE CAUTION! • When installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlamp 1. Open the hood. 2. Reach behind the headlamp unit in the engine compartment to access the headlamp bulb lock ring. 431 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 3. Firmly grasp the lock ring on the back of the headlamp 5. Disconnect the electrical connector and replace the unit housing. bulb. 4.
432 MAINTAINING YOUR VEHICLE 2. Remove the door in the left wheel liner by twisting Right Front Turn Signal counter clockwise. Access to the bulb can be gained 1. Open the hood. through the wheel liner hole. 2. Reach behind the headlight unit in the engine compartment to access the turn signal bulb. 3. Twist the bulb counterclockwise to remove. 4. Disconnect the electrical connector and replace the bulb. Front Side Marker 1. Open the hood. 2. Remove the grille assembly as follows: a.
MAINTAINING YOUR VEHICLE 433 e. Pull the grille assembly toward you to disconnect 4. Pull the bulb straight out from the keyed opening in the grille clips to the fender and the headlamp ball- the housing. studs to the front end module. 3. Disconnect electrical connector. 4. Turn the bulb counterclockwise to remove. Front Fog Lamp (Front Fascia Mounted) 1. Reach under the vehicle to access the back of the front fog lamp. CAUTION! Do not touch the new bulb with your fingers.
434 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, and Backup Lamp 1. Open the lift gate. 2. Remove the two push pins. 3. Pull lamp straight back and disconnect electrical connection. 4. Remove the two screws attaching the backplate to the lamp assembly. 5. Pull the backplate straight back from the lamp housing. 6. Disconnect the electrical connector. 7. Remove the bulb from the backplate.
MAINTAINING YOUR VEHICLE Center High Mounted Stop Lamp (CHMSL) 1. Remove the two screws securing the CHMSL. 435 2. Disconnect the electrical connector and washer hose (if equipped) from the CHMSL. 3. Replace the CHMSL.
436 MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 4.0 Liter Engine (SAE 10W-30, API Certified) Cooling System * 3.7 Liter Engine (MOPAR威 Antifreeze/Engine Coolant 5 Year/100,000 Mile Formula or equivalent) 4.0 Liter Engine (MOPAR威 Antifreeze/Engine Coolant 5 Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 19.5 Gallons Metric 73.8 Liters 5 Quarts 5.
MAINTAINING YOUR VEHICLE 437 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 3.7L Engine Engine Oil – 4.0L Engine Engine Oil Filter Spark Plugs – 3.7L Engine Spark Plugs – 4.0L Engine Fuel Selection – 3.7L Engine Fuel Selection – 4.0L Engine Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
438 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. SAE 80W-90 Multi-Purpose Type, GL-5 Gear Lubricant or equivalent. SAE 75W-90 Gear Lubricant or equivalent. MOPAR威 DOT 3 Brake Fluid, SAE J1703 should be used.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 440 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 440 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 440 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated.
M A I N T E N A N C E 442 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of the coolant reservoir and the brake master cylinder, add as needed. S C H • Check all lights and other electrical items for correct E operation. D U At Each Oil Change L E • Change the engine oil filter. S 8 • Inspect the brake hoses and lines.
MAINTENANCE SCHEDULES 8,000 Miles (13,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 443 M 16,000 Miles (26,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
M 444 MAINTENANCE SCHEDULES A I 24,000 Miles (39,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 24,000 miles (39 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
MAINTENANCE SCHEDULES 40,000 Miles (65,000 km) or 30 Months Maintenance Service Schedule 48,000 Miles (78,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). Odometer Reading Repair Order # Signature Authorized Chrysler Dealer 445 M Date Dealer Code ❏ Change the engine oil and engine oil filter.
M 446 MAINTENANCE SCHEDULES A I 56,000 Miles (91,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 56,000 miles (91 000 km). S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 72,000 Miles (117,000 km) or 54 Months Maintenance Service Schedule 80,000 Miles (130,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
M 448 MAINTENANCE SCHEDULES A I 88,000 Miles (143,000 km) or N T 66 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 88,000 miles (143 000 km).
MAINTENANCE SCHEDULES 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). Replace the engine air cleaner filter. Replace the spark plugs (3.7L Engine). Inspect and replace PCV valve if necessary. † Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the transfer case fluid.
M 450 MAINTENANCE SCHEDULES A I 104,000 Miles (169,000 km) or N T 78 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 104,000 miles (169 000 km). ❏ Replace the spark plugs (4.0L Engine). ❏ Replace the timing belt (4.0L Engine). ❏ Flush and replace the engine coolant if not done at 60 months.
MAINTENANCE SCHEDULES 120,000 Miles (195,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ Change the automatic transmission fluid and filter(s).
M 452 MAINTENANCE SCHEDULES A I 128,000 Miles (208,000 km) or 96 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). A N ❏ Replace the engine air cleaner filter. C ❏ Replace the ignition cables (3.7L Engine). E ❏ Replace the spark plugs (3.7L Engine). S C H E D U L E S 8 ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
MAINTENANCE SCHEDULES 144,000 Miles (234,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system.
M A I N T E N A N C E S C H E D U L E S 8 454 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 459 ▫ Prepare For The Appointment . . . . . . . . . . . 457 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 459 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 457 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
456 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 463 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 463 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 463 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 457 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
458 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 Auburn Hills, MI 48321–8004 solved with this process. Phone: (800) 423–6343 • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center P.O. Box 1621 ship. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
460 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 461 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
462 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals These comprehensive Service Manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing Chrysler Group LLC vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. 463 significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
464 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
466 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 304 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 306 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 411 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 402 Air Conditioner Maintenance . . . . . . . . . . . . . . . 404 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 268 Air Conditioning Controls . . . . . . . . . . . . . .
INDEX 467 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . 417,438 Special Additives . . . . . . . . . . . . . . . . . . . . . . 417 Torque Converter . . . . . . . . . . . . . . . . . . . 295,299 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 Auxiliary Electrical Outlet (Power Outlet) . . . . . . 175 Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . 175 Axle Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438 Master Cylinder . . . . . . . . .
468 INDEX Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . . . . 182 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 180 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 353 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 96,268 Center High Mounted Stop Light . . . . . . . . . . . . 435 Certification Label . . . . . . . . . . . . . . . . . . . . . . . 353 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 377 Chart, Tire Sizing . . . . . .
INDEX 469 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 165 Customer Assistance . . . . . . . . . . . . . . . . . . . . . 457 Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 73 Daytime Running Lights . . . . . . . . . . . . . . . . . . . 149 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . .
470 INDEX Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 376 Emission Control System Maintenance . . . . . . 396,440 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 402 Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . 288 Break-In Recommendations . . . . . . . . . . . . . . . . 83 Compartment . . . . . . . . . . . . . . . . . . . . . . 393,394 Compartment Identification . . . . . . . . .
INDEX Finish Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 376 Turn Signal . . . . . . . . . . . . . . . . 88,195,431,432,434 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 286 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 438 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 436 Fluid Leaks . . .
472 INDEX Garage Door Opener (HomeLink威) . . . . . . . . . . . 165 Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . 350,352,395 Gas Gauge (Fuel Gauge) . . . . . . . . . . . . . . . . . . . 192 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 346 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 347 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . 192 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 Odometer . . . . . . . . . . . . . . . .
INDEX Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . 12 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 19 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 14 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 74,75 Information Center, Vehicle . . . . . . . . . . . . . . . . . 210 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 93 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 191,192 Instrument Panel and Controls . .
474 INDEX Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434 Brake Assist Warning . . . . . . . . . . . . . . . . . . . 314 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 196 Bulb Replacement . . . . . . . . . . . . . . . . . . . 430,431 Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 Center Mounted Stop . . . . . .
INDEX 475 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 440 Maintenance, Sunroof . . . . . . . . . . . . . . . . . . . . . 174 Malfunction Indicator Light (Check Engine) . . . . . . . . . . . . . . . . . . . . . . . 204,396 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 461 Manual Transmission Lubricant Selection . . . . . . . . . . . . . . . . . . . . . 438 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . 415 Methanol . . . . . . . . . . . . . . . . . . . . .
476 INDEX MTBE/ETBE . . . . . . . . . . . . . . . . . . . . . . . . . . . 347 Onboard Diagnostic System . . . . . . . . . . . . . . 395,396 Multi-Function Control Lever . . . . . . . . . . . . . . . 148 Opener, Garage Door (HomeLink威) . . . . . . . . . . . 165 Operator Manual (Owner’s Manual) . . . . . . . . . . . . 5 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 83 Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . 94 Overdrive . . . . . . . . . . . . . . . . . . . . . . .
INDEX Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Phone, Hands-Free (Uconnect™) . . . . . . . . . . . . . . 96 Placard, Tire and Loading Information . . . . . . . . . 321 Polishing and Waxing . . . . . . . . . . . . . . . . . . . . . 421 Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . 302,303 Sunroof . . . . . . . . . . . .
478 INDEX Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . 74 Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . 38 Roll Over Warning . . . . . . . . . . . . . . . . . . . . . . . . 4 Roof Type Carrier . . . . . . . . . . . . . . . . . . . . . . . 185 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . 85 Safety Checks Outside Vehicle . . . . . . . . . . . . . . .
INDEX Service Engine Soon Light (Malfunction Indicator) . . . . . . . . . . . . . . . . . . . . 204 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 461 Setting the Clock . . . . . . . . . . . . . . . . . . 224,243,252 Settings, Personal . . . . . . . . . . . . . . . . . . . . . . . . 218 Shift Lock Manual Override . . . . . . . . . . . . . . . . 290 Shifting Automatic Transmission . . . . . . . . . . . . . . 291,295 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . .
480 INDEX Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . 401 System, Remote Starting . . . . . . . . . . . . . . . . . . . . 25 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Temperature Control, Automatic (ATC) . . . . . . . . 272 Temperature Gauge, Engine Coolant . . . . . . . . . . 192 Tether Anchor, Child Restraint . . . . . . . . . . . . . . . 78 Tie Down Hooks, Cargo . . . . . . . . . . . . . . . . . . . 180 Tilt Steering Column . . . . . . . . . . . . . . .
INDEX Torque Converter Clutch . . . . . . . . . . . . . . . . 295,299 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355,387 24-Hour Towing Assistance . . . . . . . . . . . . . . . 111 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . . 387 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Recreational . . . . . . . . . . . . . . . . . . . . . . . . . . 371 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Towing Assistance . . . . . . . .
482 INDEX Uconnect™ (Hands-Free Phone) Uniform Tire Quality Grades . . Universal Transmitter . . . . . . . Upholstery Care . . . . . . . . . . . . . . . . . . . . . . . . 96 . . . . . . . . . . . . . . 463 . . . . . . . . . . . . . . 165 . . . . . . . . . . . . . . 423 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Variance, Compass . . . . . . . . . . . . . . . . . . . . 209,217 Vehicle Certification Label . . . . . . . . . . . . . . . . .
2011 Nitro 2011 OWNER’S MANUAL Chrysler Group LLC 11KA74-126-AB Second Edition Printed in U.S.A.
