2010 OWNER’ S MANUAL Avenger
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
INTRODUCTION 5
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 17 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 12 ▫ Rearming The System . . . . . . . . . . . . . . . . . . 18 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . 14 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 18 ▫ Locking Doors With A Key . . . . . . . . . . . . . . 14 ▫ To Disarm The System . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Remote Open Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 24 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 ▫ Programming Additional Transmitters . . . . . . 25 ▫ Transmitter Battery Replacement . . . . . . . . . . 25 ▫ General Information . . . . . . . . . . . . . . . . . . . 26 䡵 Remote Start System — If Equipped . . . . . . . . . 26 䡵 Power Windows . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Adjustable Upper Shoulder Belt Anchorage . . . 45 ▫ Advanced Front Airbag Features . . . . . . . . . . 55 ▫ Rear Seat Belts . . . . . . . . . . . . . . . . . . . . . . . 46 ▫ Airbag Deployment Sensors And Controls . . . 60 ▫ Automatic Locking Retractors (ALR) Mode — If Equipped . . . . . . . . . . . . . . . . . . . 46 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 67 ▫ Seat Belt Pretensioners — If Equipped . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic Transaxle Place the shift lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If you try to remove the key before you place the shift lever in PARK, the key may become trapped temporarily in the ignition switch lock cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inoperable.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. You can insert the key with either side up. To lock the door, turn the key rearward, to unlock the door, turn the key forward. For door lock lubrication, refer to “Maintenance Procedures” in “Maintaining Your Vehicle”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key, which has not been programmed, is also considered an invalid key even if it is cut to fit the ignition switch lock cylinder for that vehicle. 15 CAUTION! • Always remove the Sentry Key威 from the vehicle and lock all doors when leaving the vehicle unattended. • The Sentry Key威 Immobilizer system is not compatible with some after-market remote starting systems.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). This PIN is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 The new Sentry Key威 is programmed. The Remote • This device must accept any interference that may be Keyless Entry (RKE) transmitter will also be proreceived, including interference that may cause undesgrammed during this procedure. ired operation. Repeat this procedure to program up to eight keys.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rearming The System If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the Vehicle Security Alarm will rearm itself. 3. The Vehicle Security Light in the instrument cluster will flash for 16 seconds. This shows that the Vehicle Security Alarm is arming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 whether you are in the vehicle or not. If you remain in the To Disarm The System Either press the UNLOCK button on the RKE transmitter vehicle and open a door, the alarm will sound. If this or insert a valid Sentry Key威 into the ignition lock occurs, disarm the Vehicle Security Alarm. cylinder and turn the key to the ON/START position.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This feature also turns on the approach lighting (if equipped). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Remote Key Unlock, Driver Door/All Doors First Press This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE transmitter.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Release both buttons at the same time. Flash Lights With Lock The feature will cause the turn signal lights to flash when 3. Test the feature while outside of the vehicle, by the doors are locked or unlocked with the RKE transmitpressing the LOCK/UNLOCK buttons on the RKE transter. This feature can be turned on or turned off. To change mitter with the ignition in the LOCK position, and the the current setting, proceed as follows: key removed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 3. Test the feature while outside of the vehicle, by Vehicle Information Center (EVIC)/Personal Settings pressing the LOCK/UNLOCK buttons on the RKE trans- (Customer-Programmable Features)” in “Understanding mitter with the ignition in the LOCK position, and the Your Instrument Panel” for further information. key removed. To Lock the Doors 4.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the To Unlatch the Trunk Press the TRUNK button on the RKE transmitter two following steps: times to unlatch the trunk. 1. Press the LOCK button on a programmed RKE transmitter for at least four seconds, but not longer than Remote Open Window Feature — If Equipped 10 seconds. Then, press the PANIC button while still The RKE remotely lowers both driver and passenger front windows simultaneously.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 headlights and park lights will flash, the horn will pulse NOTE: Perchlorate Material — special handling may on and off, and the Illuminated Entry system (if apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. equipped) will turn on. 1. With the RKE transmitter buttons facing down, use a The Panic Alarm will stay on for three minutes unless flat blade to pry the two halves of the RKE transmitter you turn it off by pressing the PANIC button a second apart.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the battery. Avoid touching the If your RKE transmitter fails to operate from a normal new battery with your fingers. Skin oils may cause distance, check for these two conditions. battery deterioration. If you touch a battery, clean it with 1. Weak battery in the RKE transmitter. The expected life rubbing alcohol. of battery is five years. 3. To assemble the RKE transmitter case, snap the two 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How to Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • Trunk closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level, and • RKE PANIC button not pressed 27 WARNING! • Do not start or run an engine in a closed garage or confined area.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shut downs, the system NOTE: • If an engine fault is present the vehicle will start and will disable the one-time press of the Remote Start button for two seconds after receiving a valid remote start then shut down 10 seconds later. request. • For security, power window operation is disabled To Exit Remote Start Mode and Drive the Vehicle when the vehicle is in the Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS 29 WARNING! Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Manual Lock Plunger • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power Door Locks A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Auto Unlock On Exit Auto Unlock On Exit Programming The doors will unlock automatically on vehicles with The Automatic Unlock Doors On Exit feature can be power door locks if: enabled or disabled as follows: 1. The Automatic Unlock Doors On Exit feature is en- • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle abled. Information Center (EVIC)/Personal Settings (Cus2.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Automatic Unlock Doors On Exit feature in accordance with local laws. Child Protection Door Lock System (Rear Doors) The Child Protection Door Locks (Rear Doors) are located inside the rear edge of the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, move the lock plunger up (UNLOCKED position), roll down the window, and open the door with the outside door handle. POWER WINDOWS position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There is a single window control on the passenger’s door trim panel, which operates the passenger door window. The window controls will operate when the ignition switch is turned to the ON or ACC position, and when the accessory delay feature is active. WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Auto Window Up — If Equipped • Any impact due to rough road conditions may trigger Lift the window switch to the second detent, release, and the auto reverse function unexpectedly during autothe window will go up automatically. closure. If this happens, pull the switch lightly to the first detent and hold to close window manually. To cancel the Auto Up movement, operate the switch either in the up or down direction and release the switch.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCK button. To enable the window controls, press the window control button again. Using the Remote Open Windows Feature with Key Fob – If Equipped To lower the front windows using the RKE transmitter perform the following procedure: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 buffeting occurs with the sunroof open, then adjust the With the ignition switch in the LOCK position or with the key out, the word “deck” will display until the trunk is sunroof opening to minimize the buffeting. closed. TRUNK RELEASE Use the Remote Keyless Entry (RKE) On Electronic Vehicle Information Center (EVIC) transmitter to open the trunk from equipped vehicles, the words “Trunk Ajar” will display. outside the vehicle.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Internal Emergency Release As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • An energy-absorbing steering column and steering NOTE: The Advanced Front Airbags have a multistage wheel inflator design. This allows the airbag to have different rates of inflation based on the severity and type of • Knee bolsters/blockers for front seat occupants collision. • Front seat belts incorporate pretensioners to enhance Please pay close attention to the information in this occupant protection by managing occupant energy section.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even conditions. However, in a collision the belt will lock and on short trips. Someone on the road may be a poor driver reduce your risk of striking the inside of the vehicle or and cause a collision that includes you. This can happen being thrown out. far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job properly. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Lap/Shoulder Belt Untwisting Procedure Adjustable Upper Shoulder Belt Anchorage Use the following procedure to untwist a twisted lap/ In the front seat, the shoulder belt can be adjusted shoulder belt. upward or downward to position the belt away from your neck. Push ANCHORAGE button to release the 1. Position the latch plate as close as possible to the anchorage, and move it up or down to the position that anchor point. fits you best. 2.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. When To Use The Automatic Locking Mode Use the Automatic Locking Mode anytime a child safety seat is installed in a seating position that has a belt with this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners — If Equipped The seat belts for both front seating positions may be equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However if during a front impact, a secondary rear impact occurs, the AHR may deploy based on the severity and type of the impact. CAUTION! All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 49 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 2 Hand Positioning Points On AHR 2. Position the hands on the top of the deployed AHR at a comfortable position.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 — Final Downward Movement To Engage Locking Mechanism AHR In Reset Position NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the Active Head Restraints, see an authorized dealer. into the back decorative plastic half. • For safety reasons, have the Active Head Restraints checked by a qualified specialist at an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert姞) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the BeltAlert威 will alert the driver to buckle the seat belt. The driver should also instruct all other occupants to buckle their seat belts.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Watch for the Seat Belt Reminder Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt partially each time when unbuckling. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. 4. Turn the ignition switch to the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on the severity and type of collision. driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with SABIC, they are located above the side windows. The trim covering the side airbags is labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Knee Impact Bolster • Driver Advanced Front Airbag • Passenger Advanced Front Airbag 55 determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors. The first stage inflator is triggered immediately during an impact that requires airbag deployment.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags may no longer be functional. The protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 When the airbag deploys, it opens the seam between the front and side of the seat’s trim cover. Each airbag deploys independently, that is a left side impact deploys the left airbag only and a right-side impact deploys only the right airbag.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes side impact sensors adjacent to both front and rear seat occupants that are calibrated to deploy the SABIC airbags during impacts that require airbag occupant protection. WARNING! • If your vehicle is equipped with left and right Supplemental Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger Advanced Front Airbag. An airbag deployment can cause severe injury or death to infants in that position. Children that are not big enough to wear the vehicle seat belt properly (see section on Child Restraints) should be secured in the rear seat in child restraints or beltpositioning booster seats.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⴖIf You Need Assistanceⴖ. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC determines if deployment of the front and/or side airbags in a frontal or side collision is required. Based on the impact sensors signals, a central electronic ORC deploys the Advanced Front Airbags, SABIC airbags — if equipped, Supplemental Seat-Mounted Side Airbags — if equipped, and front seat belt pretensioners — if equipped, as required, depending on the severity and type of impact.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE in the ACC position, or not in the ignition, the airbag system is not on and the airbags will not inflate. The ORC contains a backup power supply system that may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. Also, the ORC turns on the Airbag Warning Light in the instrument panel for approximately six to eight seconds for a self-check when the ignition is first turned on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 triggered, releasing a quantity of non-toxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door. The side airbags fully inflate in about 10 milliseconds.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE covers the window. The airbag inflates in about 30 ms (about one-quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side curtain airbag inflates. This especially applies to children. The side curtain airbag is only about 3-1/2 in (9 cm) thick when it is inflated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Front and/or side airbags will not deploy in all collisions. This does not mean something is wrong with the airbag system. If you do have a collision, which deploys the airbags, any or all of the following may occur: 65 airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The Airbag Warning Light does not come on during the six to eight seconds when the ignition switch is first turned on. • The Airbag Warning Light remains on after the six to eight second interval.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Under certain circumstances, EDR data may not be accessing the electronic data stored, unless ordered to image the data by a court with legal jurisdiction (i.e., recorded (e.g., loss of battery power). pursuant to a warrant). A copy of the data will be In conjunction with other data gathered during a comprovided to the custodial entity upon request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. 3. Requested by police under a legal warrant. 4. Otherwise required by law. Data parameters that are recorded: Children 12 years and younger should ride properly • Diagnostic trouble code(s) and warning light status for buckled up in a rear seat, if available.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for • The infant carrier is only used rearward-facing in the children from newborn size to the child almost large vehicle. It is recommended for children who weigh up enough for an adult safety belt. Always check the child to about 20 lbs (9 kg). Convertible child seats can be seat owner’s manual to ensure you have the correct seat used either rearward-facing or forward-facing in the for your child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
72 • • • • THINGS TO KNOW BEFORE STARTING YOUR VEHICLE bend over the front of the seat when their back is • In the rear seat, you may have trouble tightening the against the seatback, should use the lap/shoulder belt lap/shoulder belt on the child restraint because the in a rear seat. buckle or latch plate is too close to the belt path opening on the restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 have lower anchorages that are capable of accommodating LATCH-compatible child seats having flexible, When your child restraint is not in use, secure it in webbing-mounted lower attachments. Child seats with the vehicle with the seat belt or remove it from the fixed lower attachments must be installed in the outboard positions only. Regardless of the specific type of vehicle. Don’t leave it loose in the vehicle.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraints having tether straps and hooks for connection to the top tether anchorage, have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. Installing the LATCH-Compatible Child Restraint System We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE cover directly behind the seat where you are placing the child restraint and attach the tether strap to the anchorage, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint. Finally, tighten all three straps as you push the child restraint rearward and downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, 1. Rotate the cover over the anchor directly behind the route the tether strap under the head restraint and seat where you are placing the child restraint. between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. Installing Child Restraint Tether Strap 3.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the The seat belt must be in the Automatic Locking Mode in release button facing out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat. Make sure that: • The child is upright in the seat. 79 Transporting Pets Airbags deploying in the front seat could harm your pet.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades refer to “Maintenance Procedures” in “Maintaining Your Vehicle”. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Seat Belts feel the air directed against the windshield. See your Inspect the belt system periodically, checking for cuts, authorized dealer for service if your defroster is frays, and loose parts. Damaged parts must be replaced inoperable. immediately. Do not disassemble or modify the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside the Vehicle Door Latches Check for positive closing, latching, and locking. Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 89 ▫ Manual Front Seat Adjustments . . . . . . . . . . . 94 ▫ Automatic Dimming Mirror — If Equipped . . . 90 ▫ Driver Seat Manual Height Adjuster — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 95 ▫ Power Mirrors . . . . . . . . . . .
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Fold-Flat Front Passenger Seat . . . . . . . . . . . 102 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 110 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . 103 ▫ Daytime Running Lights — If Equipped . . . . 110 ▫ Folding Rear Seat Center Armrest . . . . . . . . 104 ▫ Lights On Reminder . . . . . . . . . . . . . . . . . . 110 䡵 To Open And Close The Hood . . . . . . . . . . . . 105 ▫ Instrument Panel Dimmer . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 䡵 Electronic Speed Control . . . . . . . . . . . . . . . . 118 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 127 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 118 ▫ Sunroof Operation . . . . . . . . . . . . . . . . . . . 128 ▫ To Set a Desired Speed . . . . . . . . . . . . . . . . 119 ▫ Auto Sunroof Express With Anti-Pinch Protection — If Equipped . . . . . . . . . . . . . . 129 ▫ To Deactivate . . . . . . . . . . . . . . . . .
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Video Console — If Equipped . . . . . . . . . . . 138 ▫ Driver’s Side Sunglass Holder — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 134 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 139 ▫ Cargo Area . . . . . . . . . . . . . . . . . . . . . . . . 135 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . 136 ▫ Dual Storage Bins . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 3 Power Mirror Switch Mirror Directions After selecting a mirror, move the knob in the same Adjusting Side View Mirrors direction you want the mirror to move. When finished, Outside Mirror — Driver Side return the knob to the center O (OFF) position to guard Adjust the outside mirror to center on the adjacent lane of against accidentally moving a mirror position. traffic, with a slight overlap of the view obtained on the inside mirror.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a hands-free system that allows you to use voice commands to dial a phone number stored in your cellular phone. Press the Uconnect™ Phone on the radio or steering wheel controls (if button equipped) and follow the instructions to pair the cellular phone. Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front Seat Adjustments The adjusting bar is located at the front of the seats, near the floor. Pull the bar upward to move the seat to the desired position. After releasing the adjusting bar, apply forward and rearward body pressure to be sure the seat is latched. Manual Seat Adjusting Bar WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Driver Seat Manual Height Adjuster — If Equipped A lever style height adjustment feature enhances comfort for petite as well as tall drivers. A lever with a ratcheting mechanism, located on the outboard side of the seat, raises and lowers it. Total travel is 2.2 in. (56 mm). Reclining Bucket Seats The recliner control is on the side of the seat.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting Active Head Restraints Active Head Restraints can reduce the risk of injury in the event of a rear impact. The Active Head Restraint should be adjusted so the top of the head restraint is located above the top of your ear. 97 To raise the head restraint, pull upward on the head restraint (on some models, you may need to press the push button).
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the seat up, down, forward, rearward, or to tilt the seat. Use the seatback control to adjust the angle of the seatback. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for the heated seats are located in the center console below the climate controls. After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low, and none for Off. Press the switch once to select High-level heating.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. Fold-Flat Front Passenger Seat The recline handle on the front passenger seat also releases the seatback to fold forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 The hard seatback features a work surface and a molded Folding Rear Seat To provide additional storage area, the rear seatback can rim for retaining items stored on the seatback panel. be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. When returning the rear seat back to the upright position, be sure the seatback is latched.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. Folding Rear Seat Center Armrest The rear seat is equipped with a folding armrest with cupholders.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 105 2. Lift the secondary latch located under the front edge of the hood, near the center and raise the hood. 1. Pull the hood release lever located under the left side of the instrument panel.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the left underside of the hood. CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 passing light, fog lights, instrument panel light dimming Headlights and Parking Lights and turn signals. The multifunction lever is located on Turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for the left side of the steering column. headlight operation.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the engine running and the multifunction lever in Automatic Headlights — If Equipped Turning the end of the multifunction lever to the third the AUTO position, the headlights will turn on and turn detent (AUTO), will activate the automatic headlight off based on the surrounding light levels. system. Headlight Time Delay There is also a feature that delays turning off the vehicle lights for 30, 60 or 90 seconds after the ignition switch is turned OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you, to switch the headlights back to low beam.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped The front fog light switch is on the multifunction lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the multifunction lever. NOTE: The front fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the front fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. 3 Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the parking lights or headlights are on.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically. Interior lighting also comes on when a door is opened or the dimmer control is turned fully upward, past the second detent. There is a second light located midway back in the headliner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 3 Windshield Wiper/Washer Lever Changing Wiper Speeds Rotate the end of the lever to the LO position for NOTE: The wipers will automatically return to the park low-speed wiper operation, or to the HI position for position if you turn the ignition switch OFF while they high-speed wiper operation. are operating. The wipers will resume operation when you turn the ignition switch to the ON position again.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the wiper control is in the delay range, the wipers will operate in low-speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. 117 To unlock the steering column, pull the control handle outward. To tilt the steering column, move the steering wheel upward or downward as desired.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic The Electronic Speed Control lever is located on the right Speed Control ON/OFF button and resetting the desired side of the steering wheel. vehicle set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To Set a Desired Speed Turn the Electronic Speed Control ON. When the vehicle reaches the speed desired, press down on the lever and release SET DECEL.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping RESUME ACCEL once will result in a 1 mph (2 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 3 mph (5 km/h), etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 On steep hills, a greater speed loss or gain may occur so The HomeLink威 buttons that are located in the headliner it may be preferable to drive without Electronic Speed or sun visor designate the three different HomeLink威 Control. channels. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Place the handheld transmitter 1 to 3 in (3 to 8 cm) away • After training a HomeLink威 channel, if the garage from the HomeLink威 button you wish to program while door does not operate with HomeLink威 and the gakeeping the indicator light in view. rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, 3.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer. door. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink威 To operate, press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE successfully accepted the frequency signal. The indica- Troubleshooting Tips tor light will flash slowly and then rapidly when fully If you are having trouble programming HomeLink威, here are some of the most common solutions: trained. If you unplugged the device for training, plug it back in • Replace the battery in the original transmitter. at this time. • Press the LEARN button on the Garage Door Opener to complete the training for a Rolling Code.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 2. This device must accept any interference that may be POWER SUNROOF — IF EQUIPPED received including interference that may cause undesired The sunroof controls are mounted between the dome/ reading lights. operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: The sunshade cannot be closed if the sunroof is Venting Sunroof — Express Press and release the “Vent” button, the sunroof will open. open to the vent position. This is called “Express Vent”. Wind Buffeting Closing Sunroof — Express Wind buffeting can be described as the perception of Press the switch forward and release, the sunroof will pressure on the ears or a helicopter-type sound in the close automatically from any position. The sunroof will ears.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned OFF. Opening either front door will cancel this feature. The instrument panel power outlet, located below the climate control knobs, has power available only when the ignition is ON. This power outlet will also operate a conventional cigar lighter unit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 The center console power outlet is powered directly from NOTE: the battery (power available at all times). Items plugged • To ensure proper operation a MOPAR威 knob and element must be used. into this power outlet may discharge the battery and/or prevent the engine from starting. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! For vehicles equipped with the heated and cooled cupholder, locate the cup holder ash receiver in the forward cupholder. 133 CUPHOLDERS There are two cupholders located in the center console for the front passengers. 3 The optional ash receiver also comes with a cigar lighter. You may use the power outlet, located in the instrument panel below the climate control knobs, or in the bottom of the console compartment, for this cigar lighter.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Bottle Holder There are built-in bottle holders located in both rear door trim panels. WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury. STORAGE Driver’s Side Sunglass Holder — If Equipped An integrated sunglass holder is located in the headliner above the sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. WARNING! Sunglass Holder Cargo Area The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When the seats are folded down, they provide a continuous, nearly flat extension of the load floor.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 3 Console Features Dual Storage Bins Lifting a latch at the front of the hinged armrest provides access to these storage areas. Storage Console Detail 1 2 3 4 — — — — Release Top Compartment Release Bottom Compartment Top Compartment Bottom Compartment The left latch opens to the top storage area.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lower bin can be accessed directly, without first Video Console — If Equipped exposing the upper bin, by operating the right latch with The optional Video Entertainment System (VES)™ includes the following components: the armrest down. The first storage bin can be used to hold smaller items. • The screen for a rear seat DVD player is stored under the armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Inside the Chill Zone威 is a vent which, when opened, The glove compartment is located beneath the Chill allows either air conditioned or fresh air to flow into the Zone威 storage compartment. The glove compartment Chill Zone威 compartment. Depending on ambient tem- door swings downward for easy access. perature and A/C setting, the compartment can keep beverages cool.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 147 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . 169 䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 148 ▫ Personal Settings (Customer-Programmable Features) . . . . . . . 171 䡵 Instrument Cluster — Premium . . . . . . . . . . . 149 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 150 䡵 Electronic Vehicle Information Center (EVIC) – If Equipped . . . . . . . . . . . . . .
144 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 187 䡵 Media Center 130 (RES) — AM/FM Stereo Radio With CD Player (MP3 AUX Jack). . . . . . . 194 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 187 ▫ Operating Instructions — Radio Mode . . . . . 194 䡵 Media Center 730N/430 (RER/REN/RBZ) — AM/FM Stereo Radio And CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Info Button (CD Mode For MP3 Play) . . . . . . 214 ▫ Operating Instructions - Uconnect™ Phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 215 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/REQ/RER/RBZ/RES Radios Only) . . . . . . . . . . . . . . . . . . . . . . . . . 215 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 215 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . .
146 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 224 䡵 Radio Operation And Cellular Phones . . . . . . . 224 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 224 ▫ Manual Heating And Air Conditioning . . . . . 225 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 229 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 147 INSTRUMENT PANEL FEATURES 4 1 2 3 4 — Air Outlet — Side Window Demister Outlet — Instrument Cluster — Radio 5 6 7 8 — — — — Beverage Can Cooler Bin Glove Compartment Heated Seat Switch — If Equipped Hazard Switch 9 — Power Outlet 10 — Climate Controls 11 — Trunk Release Button
148 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 149 INSTRUMENT CLUSTER — PREMIUM 4
150 UNDERSTANDING YOUR INSTRUMENT PANEL removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and 1. Temperature Gauge the Fan control to High. This allows the heater core to act The temperature gauge shows engine coolant temperaas a supplement to the radiator and aids in removing heat ture. Any reading below the red area of the gauge shows from the engine cooling system. that the engine cooling system is operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 If jump starting is required, refer to “Jump Starting 5. Low Fuel Light When the fuel level drops to approximately 2.0 gal- Procedures” in “What To Do In Emergencies”. lons (7.6 Liters), the fuel symbol will light and a 7. Airbag Warning Light single chime will sound. The light comes on and remains on for six to NOTE: This light will remain on until a minimum of eight seconds as a bulb check when the ignition switch is first turned ON.
152 UNDERSTANDING YOUR INSTRUMENT PANEL you do not buckle up, the light will remain on. Refer to 10. Engine Temperature Warning Light “Occupant Restraints” in “Things To Know Before StartThis light warns of an overheated engine condition. If the engine is critically hot, a warning chime ing Your Vehicle” for further information. will sound 10 times. After the chime turns off, the 9. Oil Pressure Warning Light engine will still be critically hot until the light goes out.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 The light will remain on until the cause is corrected. In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair NOTE: The light may flash momentarily during sharp to the ABS system is required. cornering maneuvers which change fluid level conditions. The vehicle should have service performed, and The operation of the Brake Warning Light can be checked the brake fluid level checked.
154 UNDERSTANDING YOUR INSTRUMENT PANEL driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea 13.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 Vehicle Odometer Messages LoW TirE When the appropriate conditions exist, the odometer will When the appropriate condition exists, the odometer display the following messages: display will toggle between LoW and TirE for three cycles. door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar HOTOIL deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trunk Ajar When this message is displayed there is a transmission LoW TirE . . . . . . . . .
156 UNDERSTANDING YOUR INSTRUMENT PANEL tighten the fuel filler cap properly and press the odometer reset button to turn off the “gASCAP” message. (Refer to “Onboard Diagnostic System — OBDII” in “Maintaining Your Vehicle” for further information). If the problem continues, the message will appear the next time the vehicle is started. See your authorized dealer service center as soon as possible. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 Dual Trip Odometer — If Equipped 15. Cruise Indicator — If Equipped This indicator shows that the Electronic Speed Press and release this button to change the display from odometer to “Trip A.” Press and release it a second time Control System is ON. to change the display to “Trip B.” Press and release it a 16. Odometer/Trip Odometer Reset Button third time to change the display back to the odometer.
158 UNDERSTANDING YOUR INSTRUMENT PANEL If the light is flashing when the engine is running you 19. Electronic Stability Control (ESC) OFF Indicator may experience power loss, an elevated/rough idle, and Light — If Equipped increased brake pedal effort, and your vehicle may This light indicates the Electronic Stability Conrequire towing. Immediate service is required. trol system (ESC) has been turned off by the driver.
UNDERSTANDING YOUR INSTRUMENT PANEL 22. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light — If Equipped The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON position. It should go out with the engine running. If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system.
160 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle placard or tire inflation pressure label, you should maintain correct tire pressure, even if under-inflation has determine the proper tire inflation pressure for those not reached the level to trigger illumination of the TPMS low tire pressure telltale. tires.) Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 tires or wheels on your vehicle, to ensure that the 25. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of replacement or alternate tires and wheels allow the TPMS an onboard diagnostic system called OBD that to continue to function properly. monitors emissions, engine, and automatic transCAUTION! mission control systems. The light will illuminate when the key is in the ON position before engine start.
162 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL should come on. If the light does not come on, have the system inspected by an authorized dealer. 163 WARNING! Continued operation with the Transmission Tem27. Transmission Temperature Warning Light — perature Warning Light illuminated could cause the If Equipped fluid to boil over, come in contact with hot engine or This light indicates that the transmission fluid exhaust components causing a fire that may result in temperature is running hot.
164 UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC consists of the following: ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED • System status The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the • Vehicle information warning message displays instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by pressing the following buttons on the instrument panel switch bank located below the climate controls: Press and release the MENU button to advance the display to Trip Functions or Personal settings or to return to the default System status MENU display. Button STEP Button 165 Press and release the COMPASS button to display the compass heading and the outside temperature.
166 UNDERSTANDING YOUR INSTRUMENT PANEL • Left Rear Turn Signal Light Out (with a single chime) • ECO (Fuel Saver Indicator) — If Equipped • Right Front Turn Signal Light Out (with a single Oil Change Required — If Equipped Your vehicle is equipped with an engine oil change chime) indicator system.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 2. Fully depress the accelerator pedal slowly three times Press and release the STEP button to advance the display through the Trip Functions. within 10 seconds. 3. Turn the ignition switch to the LOCK position.
168 UNDERSTANDING YOUR INSTRUMENT PANEL • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the RESET button. • Elapsed Time Shows the total elapsed time of travel since the last reset. Elapsed time will increment when the ignition switch is in the ON or START position.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Display The compass heading indicates the direction the vehicle is facing. Press and release the compass button to display one of eight COMPASS compass heading and the outside temperature. Button 169 one or more 360–degree turns (in an area free from large metal or metallic objects) until the CAL indicator in the EVIC turns off. The compass will now function normally.
170 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press and release the STEP button until “Calibrate NOTE: Magnetic and battery powered devices, (such as cell phones, iPod’s, radar detectors, PDA’s and laptops) Compass Yes” displays in the EVIC. should be kept away from the top of the instrument 4. Press and release the RESET button and the “CAL” panel. This is where the compass module is located and indicator will quit flashing. such devices may interfere and cause false compass 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 1. Turn the ignition switch to the ON position. Leave the Personal Settings shift lever in PARK. (Customer-Programmable Features) Personal settings allows the driver to set and recall 2. Press and release the MENU button until “Personal features when the automatic transaxle is in PARK. Settings” displays in the EVIC. Press and release the MENU button until “Personal 3. Press and release the STEP button until “Compass Settings” displays in the EVIC.
172 UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock on Exit When ON is selected and the transaxle is in the PARK or NEUTRAL position, all doors will unlock when the driver’s door is opened. To make your selection, press and hold the RESET button until ON or OFF appears. Remote Key Unlock When “Driver Door 1st Press” is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button.
UNDERSTANDING YOUR INSTRUMENT PANEL Headlights With Wipers (Available with Auto Headlights Only) When ON is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and hold the RESET button until ON or OFF appears.
174 UNDERSTANDING YOUR INSTRUMENT PANEL Display ECO — If Equipped The “ECO” message is located in the EVIC, this message can be turned on or off. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. Display Units In The EVIC and odometer can be changed between English and Metric units of measure. To make your selection, press and release the RESET button until “ENGLISH” or “METRIC” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. 175 SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time.
176 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in AM, FM or Satellite (if equipped) frequencies. 177 Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones.
178 UNDERSTANDING YOUR INSTRUMENT PANEL or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 By pressing the SEEK button when the Music Type icon • DVD Enter - When the disc is in DVD Menu mode, is displayed, the radio will be tuned to the next frequency selecting DVD Enter will allow you to play the current station with the same selected Music Type name. The highlighted selection. Use the remote control to scroll Music Type function only operates when in the FM up and down the menu (if equipped). mode.
180 UNDERSTANDING YOUR INSTRUMENT PANEL • Angle – Repeatedly pressing SELECT will change • Set Home Clock - Pressing the SELECT button allows the viewing angle if supported by the DVD disc (if you to set the clock. Turn the TUNE/SCROLL control equipped). knob to adjust the hours and then press and turn the TUNE/SCROLL control knob to adjust the minutes. NOTE: Press the TUNE/SCROLL control knob again to save • The available selections for each of the above entries changes. varies depending upon the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL Audio Language — If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.⬙ Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select.
182 UNDERSTANDING YOUR INSTRUMENT PANEL a disc is loaded, changes will not be effective. Also, the both AM and FM. This allows a total of 12 AM, 12 FM, defaults are effective only if the disc supports the and 12 Satellite (if equipped) stations to be stored into pushbutton memory. The stations stored in SET 2 customer-preferred settings. memory can be selected by pressing the pushbutton AM and FM Buttons twice. Press the buttons to select AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the DVD disc does not match the region code for the radio DVD player, it will not play the disc. Customers may take their vehicle to an authorized dealer to change the region code of the player a maximum of five times.
184 UNDERSTANDING YOUR INSTRUMENT PANEL Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. SCAN Button (CD MODE) Press the SCAN button to scan through each track on the CD currently playing.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 The radio uses the following limits for file systems: Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable • Maximum number of directory levels: 8 MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the • Maximum number of files: 255 following restrictions.
186 UNDERSTANDING YOUR INSTRUMENT PANEL If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. Supported MP3/WMA File Formats The radio will recognize only files with the *.MP3/WMA extension as MP3/WMA files. Non-MP3/WMA files named with the *.MP3/WMA extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3/WMA and will not play the file.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files. LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob.
188 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. SCAN Button (Auxiliary Mode) No function. Operation Instructions - Auxiliary Mode EJECT Button (Auxiliary Mode) The auxiliary (AUX) jack is an audio input jack which No function.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Voice Command System (If Equipped) For the radio, Refer to “Voice Command” in the Uconnect™ User Manual located on the DVD for further details. 189 Operating Instructions - Video Entertainment System (VES)™ (If Equipped) Refer to “Video Entertainment System (VES)™” in the Uconnect™ User Manual located on the DVD for further details. Refer to the Uconnect™ User Manual located on the DVD Dolby威 for further details.
190 UNDERSTANDING YOUR INSTRUMENT PANEL DTS™ Operating Instructions — Voice Command ⬙DTS™⬙ and ⬙DTS™ 2.0⬙ are trademarks of Digital The- System — If Equipped Refer to “Voice Command” in the Uconnect™ User ater Systems, Inc. Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 191 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.
192 UNDERSTANDING YOUR INSTRUMENT PANEL satellite clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the system’s 1. Turn on the radio. clock very accurate once the appropriate time zone and 2. Touch the screen where the time is displayed. The daylight savings information is set. clock setting menu will appear on the screen. To Manually Set the Clock — RER/REN 3. Touch the screen where the words “Set Time Zone” are 1. Turn on the radio. displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 displayed. To move the minute backward, touch the Show Time if Radio is Off screen where the word “Min” with the arrow pointing When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed downward is displayed. as follows to change the current setting: 6. To save the new time setting, touch the screen where 1. Turn on the radio. the word “Save” is displayed. Changing Daylight Savings Time 2.
194 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 4. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 5. Select a time zone by touching the screen where your selection appears. If you do not see a time zone that you want to select, touch the screen where the word “Page” is displayed to view additional time zones in the menu. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio. Push the ON/VOLUME control knob a second and radio frequency. time to turn off the radio. Clock Setting Procedure Electronic Volume Control 1. Press and hold the TIME button until the hours blink. The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning 2.
196 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones.
UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.
198 UNDERSTANDING YOUR INSTRUMENT PANEL discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or the radio will reinsert the CD but will not play it. RW or another CD button is pressed. The RW (Reverse) A disc can be ejected with the radio and ignition OFF. button works in a similar manner.
200 UNDERSTANDING YOUR INSTRUMENT PANEL Notes on Playing MP3 Files • Maximum number of files: 255 The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited. For large numbers writing MP3 files, pay attention to the following restricof files and/or folders, the radio may be unable to tions.
UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.
202 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO 203 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate. Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
204 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 2. Adjust the hours by turning the right side TUNE/ INFO Button Press the INFO button for an RDS station (one with call SCROLL control knob. letters displayed). The radio will return a Radio Text 3. After adjusting the hours, press the right side TUNE/ message broadcast from an FM station (FM mode only). SCROLL control knob to set the minutes. The minutes RW/FF will begin to blink. Pressing the RW (Rewind) or FF (Fast Forward) buttons 4.
206 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the MUSIC TYPE Button mid-range tones. Pressing this button once will turn on the Music Type Push the rotary TUNE/SCROLL control knob a third mode for five seconds. Pressing the MUSIC TYPE button time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type College Country Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock 16-Digit Character Display College Country Language Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Program Type Soft Rhythm and Blues Sports Talk Top 40 Weather 207 16-Digit Character Display Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button
208 UNDERSTANDING YOUR INSTRUMENT PANEL window. Select the button (1–6) you wish to lock onto this SETUP Button Pressing the SETUP button allows you to select between station and press and release that button. If a button is not selected within five seconds after pressing the SET/ the following items: RND button, the station will continue to play but will not • Set Clock — Pressing the SELECT button will allow be stored into pushbutton memory. you to set the clock.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Buttons 1 - 6 Inserting Compact Disc(s) These buttons tune the radio to the stations that you Gently insert one CD into the CD player with the CD commit to pushbutton memory (12 AM and 12 FM label facing up. The CD will automatically be pulled into stations). the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than DISC/AUX Button 1.0 in (2.
210 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player. EJECT Button - Ejecting a CD Press the EJECT button to eject the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. 211 Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
212 UNDERSTANDING YOUR INSTRUMENT PANEL a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems.
UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.
214 UNDERSTANDING YOUR INSTRUMENT PANEL begin playing the files contained in that folder (or the Operation Instructions - Auxiliary Mode next folder in sequence if the selection does not contain The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an playable files). MP3 player or cassette player and utilize the vehicle’s The folder list will time out after five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 coast. The subscription service provider is Sirius Satellite Operating Instructions - Uconnect™ Phone Radio. This service offers over 130 channels of music, (If Equipped) Refer to “Uconnect™ Phone” in the Uconnect™ User sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios. Manual located on the DVD for further details.
216 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification ESN/SID Access With REN/RER/RBZ Radios While in SAT mode, press the MENU button on the radio Number (ESN/SID) Please have the following information available when faceplate. calling: Next, touch the SUBSCRIPTION tab on the touch screen. 1. The Electronic Serial Number/Sirius Identification All the ESNs that apply to your vehicle will display. Number (ESN/SID).
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will • The vehicle is parked in an underground parking remain tuned to the new channel until you make another structure or under a physical obstacle. selection.
218 UNDERSTANDING YOUR INSTRUMENT PANEL additional three seconds will make the radio display the Toggle the MUSIC TYPE button again to select the music Song Title all of the time (press and hold again to return type. to normal display). By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons channel with the same selected Music Type name.
UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the SET button, the channel will continue to play but will not be stored into pushbutton memory.
220 UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED The optional Video Entertainment System (VES)™ includes the following components for rear seat entertainment: • A diagonal 7 in (17.8 cm) Liquid Crystal Display (LCD) screen integrated into the center console armrest. The screen features brightness control for optimum daytime and nighttime viewing.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin. 4 VES™ Video Screen NOTE: Close the armrest after the LCD screen has been raised to its viewing position.
222 UNDERSTANDING YOUR INSTRUMENT PANEL Audio/Video RCA Jacks (AUX Jacks) are rocker-type switches with a pushbutton in the center on the rear of the center console enable of each switch. Reach behind the steering wheel to access the monitor to display video directly the switches. from a video camera, connect video games for display on the screen, or play music directly from an MP3 player. 1. Video in (yellow) 2. Left audio in (white) 3.
UNDERSTANDING YOUR INSTRUMENT PANEL Right-Hand Switch Functions • Press the top of the switch to increase the volume. • Press the bottom of the switch to decrease the volume. 223 Left-Hand Switch Functions for Media (i.e., CD) Operation • Press the top of the switch once to listen to the next track. • Press the button in the center of the switch to change • Press the bottom of the switch once either to listen to modes (i.e., AM, FM, etc.).
224 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particuCD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Heating and Air Conditioning 225 Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position. There are four blower speeds. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
226 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Mode Control (Air Direction) Rotate this control to regulate the temRotate this control to choose from sevperature of the air inside the passenger eral patterns of air distribution. You compartment. Rotating the dial left can select either a primary mode as into the blue area of the scale indicates identified by the symbols on the concooler temperatures while rotating trol, or a blend of two of these modes.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 NOTE: For all settings except full cold or full hot, there Defrost is a difference in temperature between the upper and Air is directed through the windshield and side window demist outlets. Use this mode with maxilower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but mum blower and temperature settings for best windshield and side window defrosting. cool conditions.
228 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • When the ignition switch is turned to the LOCK • Continuous use of the recirculation mode may make position, the recirculation feature will be cancelled. the inside air stuffy and window fogging may occur. Air Conditioning Control Extended use of this mode is not recommended. Press this button to engage the Air • The use of the recirculation mode in cold or damp Conditioning.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 • ECONOMY MODE If economy mode is desired, press the A/C button to turn OFF the indicator light and the A/C compressor. Then, move the temperature control to the desired temperature. Automatic Operation The Automatic Temperature Control system automatically maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Automatic Temperature Control (ATC) — If Equipped Operation of the system is quite simple. 1.
230 UNDERSTANDING YOUR INSTRUMENT PANEL the desired comfort level require air conditioning, the system will automatically make the adjustment. to flash three times and then turn off. This indicates that the system is in AUTO mode and requesting the air conditioning is not necessary. You will experience the greatest efficiency by simply allowing the system to function automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control For full automatic operation or for automatic blower operation turn the knob to AUTO position. In manual mode there are seven blower speeds that can be individual selected. In off position the blower will shut off. Manual Operation This system offers a full complement of manual override features, which consist of Blower Preferred Automatic, 231 Mode Preferred Automatic, or Blower and Mode Preferred Automatic.
232 UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL 233 The operator can override the AUTO mode setting to • Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets. • Panel Air is directed through the outlets in the instrument • Mix Air is directed through the floor, defrost, and side panel. These outlets can be adjusted to direct airflow.
234 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn OFF the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into Recirculation Mode at this time.
236 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Mix mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Control Setting Suggestions for Various Weather Conditions 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 243 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 246 ▫ Automatic Transmission . . . . . . . . . . . . . . . 243 ▫ Key Ignition Park Interlock . . . . . . . . . . . . . 248 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 243 ▫ Brake/Transmission Interlock System . . . . . . 248 ▫ Extreme Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . . . . . . . . . . .
240 STARTING AND OPERATING ▫ General Information . . . . . . . . . . . . . . . . . . 254 ▫ Traction Control System (TCS) . . . . . . . . . . . 265 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 255 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . 265 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . 255 ▫ Hill Start Assist (HSA) – If Equipped . . . . . . 266 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 ▫ Electronic Stability Control (ESC) . . .
STARTING AND OPERATING 241 ▫ Compact Spare Tire . . . . . . . . . . . . . . . . . . . 285 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 300 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 286 ▫ 2.4L And 2.7L Engine . . . . . . . . . . . . . . . . . 300 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . 287 ▫ 3.5L Engine . . . . . . . . . . . . . . . . . . . . . . . . 300 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . 288 ▫ Reformulated Gasoline . .
242 STARTING AND OPERATING ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . 307 ▫ Overloading . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ Selection Of Engine Oil For Flexible Fuel Vehicles (E85) And Gasoline Vehicles . . . . . . 308 ▫ Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . 308 ▫ Replacement Parts . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the keys in the ignition.
244 STARTING AND OPERATING motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start, the starter will disengage automatically in 10 seconds. If this occurs, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure. WARNING! (Continued) WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
STARTING AND OPERATING 245 the way to the floor and hold it there while cranking the With Tip Start engine. This should clear any excess fuel in case the If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” proceengine is flooded. dures, it may be flooded. To clear any excess fuel, push CAUTION! the accelerator pedal all the way to the floor and hold it.
246 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine, and permits CAUTION! quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a Damage to the transmission may occur if the followgrounded, three-wire extension cord.
STARTING AND OPERATING 247 WARNING! • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
248 STARTING AND OPERATING WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into PARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
STARTING AND OPERATING 249 • Insert the ignition key and rotate it to the ON position NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety • Remove the cup holder liner feature is inoperable. The engine can be started and • Insert a key, screwdriver, or finger into the front hole stopped, but the key cannot be removed until you obtain then push and hold the manual override release lever service. forward.
250 STARTING AND OPERATING Never attempt to use PARK while vehicle is in motion. Apply parking brake when leaving vehicle in this range. When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK.
STARTING AND OPERATING NEUTRAL This range is used when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident.
252 STARTING AND OPERATING DRIVE 3— Four-Speed Transmission This range eliminates shifts into fourth gear. The transmission will operate normally in first and second gear. Shifts into third may be delayed to provide second gear operation at higher speeds. The ⬙3⬙ range should also be used when descending steep grades to prevent brake system distress.
STARTING AND OPERATING 253 In the event that the problem has been momentary, the control. AutoStick威 allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and transmission can be reset to regain all forward gears. improve overall vehicle performance. This system can 1. Stop the vehicle. also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, 2. Shift into PARK. trailer towing, and many other situations. 3.
254 STARTING AND OPERATING AutoStick威 is deactivated when the shift lever is shifted • The transmission will automatically shift up when from the AutoStick (+/-) position into the DRIVE maximum engine speed is reached while AutoStick威 is position. engaged. General Information • Transmission shifting will be more noticeable when AutoStick威 is engaged. • You can start out, from a stop, in any gear except sixth.
STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident.
256 STARTING AND OPERATING DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly.
STARTING AND OPERATING 257 CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
258 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components.
260 STARTING AND OPERATING The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To release the parking brake, pull the lever up slightly, press the center button, then lower the lever completely. When the parking brake is applied with the ignition switch ON, the “Brake Warning Light” in the instrument cluster will illuminate.
STARTING AND OPERATING make it difficult to move the shift lever out of PARK. The parking brake should always be applied whenever the driver is not in the vehicle. WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
262 STARTING AND OPERATING ANTI-LOCK BRAKE SYSTEM (ABS) The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most braking conditions. The system operates with a separate computer to modulate the hydraulic pressure to prevent wheel lock-up and avoid skidding on slippery surfaces. WARNING! • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer.
STARTING AND OPERATING The “Anti-Lock Brake Warning Light” monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the “Anti-Lock Brake Warning Light” remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.
264 STARTING AND OPERATING • the clicking sound of solenoid valves, • brake pedal pulsations, All vehicle wheels and tires must be the same size and type, and tires must be properly inflated to produce accurate signals for the computer. • and a slight drop or fall away of the brake pedal at the ELECTRONIC BRAKE CONTROL SYSTEM end of the stop. Your vehicle may be equipped with an optional adThese are all normal characteristics of ABS.
STARTING AND OPERATING 265 help avoid skidding on slippery surfaces during braking. Brake Assist System (BAS) Refer to “Anti-Lock Brake System” in “Starting and The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The Operating” for further information.
266 STARTING AND OPERATING WARNING! • The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 267 The system will only work if the intended direction of the HSA Activation Criteria The following criteria must be met in order for HSA to vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and the vehicle is activate: in DRIVE and the activation criteria are met, HSA will • Vehicle must be stopped activate.
268 STARTING AND OPERATING 1. Center the steering wheel (front wheels pointing 9. Turn the ignition switch to the OFF position and then straight forward). back to the ON position. If the sequence was completed properly, the “ESC Off Indicator Light” will blink several 2. Shift the transmission into NEUTRAL. times to confirm HSA is disabled. 3. Apply the parking brake. 10. Repeat these steps if you want to return this feature 4. Start the engine. to it’s previous setting. 5. Release the clutch pedal.
STARTING AND OPERATING Electronic Stability Control (ESC) This system enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
270 STARTING AND OPERATING WARNING! (Continued) • ESC cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ESC-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. detected in the ESC system.
STARTING AND OPERATING 271 Partial ESC Mode ESC Operating Modes All ESC equipped vehicles can choose the following ESC This mode is entered by momentarily pressing the “ESC operating modes: Off” switch (located in the lower switch bank below the heater/air conditioning controls). When in “Partial Off” ESC On mode, the TCS portion of ESC, except for the limited slip This is the normal operating mode for ESC.
272 STARTING AND OPERATING WARNING! In the Partial ESC mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESC is unavailable. NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC Off” switch.
STARTING AND OPERATING NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa• tion. Example: P215/65R15 95H. 273 tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the size designation. Example: LT235/85R16. Temporary spare tires are high-pressure compact spares designed for temporary emergency use only.
274 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 275 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
276 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 277 Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
278 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
STARTING AND OPERATING This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. 279 axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section.
280 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcusengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity. For example, if “XXX” and number and size of occupants.
STARTING AND OPERATING 281 5
282 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
284 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
STARTING AND OPERATING 285 loading may be required for high-speed vehicle opera- Radial-Ply Tires tion. Refer to original equipment or an authorized tire WARNING! dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle WARNING! poorly. The instability could cause an accident. AlHigh speed driving with your vehicle under maxiways use radial ply tires in sets of four.
286 STARTING AND OPERATING WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary-use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
STARTING AND OPERATING 287 Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.
288 STARTING AND OPERATING Life of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors including but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 289 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
290 STARTING AND OPERATING CAUTION! Damage to the vehicle may result if tire chains are used. TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. SNOW TIRES Some areas of the country require the use of snow tires during Winter.
STARTING AND OPERATING 291 The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12 F (7 C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period.
292 STARTING AND OPERATING The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warning (Tire Pressure Monitoring Telltale Light) illuminates, you must increase the tire pressure to the recommended cold placard pressure in order for the “Tire Pressure Monitoring Telltale Light” to turn off.
STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
294 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will and the TPMS will monitor the actual tire pressure in illuminate in the instrument cluster and a chime the tire. will sound when tire pressure is low in one or Base System more of the four active road tires.
STARTING AND OPERATING will repeat, providing the system fault still exists. The “Tire Pressure Monitoring Telltale Light” will turn off when the fault condition no longer exists. A system fault can occur due to any of the following: 295 NOTE: 1. The compact spare tire (if so equipped) does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 1. Jamming due to electronic devices or driving next to 2.
296 STARTING AND OPERATING 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically and the “TPM Telltale Light” will turn OFF, as long no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information.
STARTING AND OPERATING more of the four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing. 297 Should this occur, you should stop as soon as possible, and inflate all tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value.
298 STARTING AND OPERATING (- -) in place of the pressure value to indicate which SYSTEM⬙ message will no longer display, and a pressure sensor is not being received. value will display in place of the dashes. A system fault can occur due to any of the following: 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3.
STARTING AND OPERATING 299 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the “TPM Telltale Light” will turn OFF and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low-pressure warning limit in any of the four active road tires. The 3.
300 STARTING AND OPERATING The tire pressure sensors are covered under one of the 3.5L Engine The 3.5L engine is designed to meet all following licenses: emissions regulations and provide satisfactory fuel economy and performance when United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 using high-quality unleaded gasoline havCanada . . . . . . . . . . . . . . . . . . . . . . . . 2671-S120123 ing an octane range of 87 to 89.
STARTING AND OPERATING 301 symptoms, try another brand of gasoline (with the ap- The manufacturer supports the use of reformulated gasopropriate octane rating for your engine) before consider- lines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and ing service for the vehicle. fuel system components.
302 STARTING AND OPERATING NOTE: The 2.7L engine is now rated for E85 Ethanol • OBD II “Malfunction Indicator Light” on use (EXCEPT CALIFORNIA EMISSION STATES). Only • poor engine performance vehicles with the E-85 fuel filler door label can operate on E-85. Refer to “Flexible Fuel” in “Starting and Operating” • poor cold start and cold drivability for further information.
STARTING AND OPERATING 303 blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether or not his/her gasoline contains MMT.
304 STARTING AND OPERATING CAUTION! (Continued) • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers, is not recommended.
STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. 305 FLEXIBLE FUEL (2.
306 STARTING AND OPERATING NOTE: The 2.7L engine is now rated for E85 Ethanol use (EXCEPT CALIFORNIA EMISSION STATES). Only vehicles with the E85 fuel filler door label can operate on E85. Only vehicles with the E85 fuel filler door label can operate on E85.
STARTING AND OPERATING 307 Ethanol Fuel (E85) For best results, a refueling pattern that avoids alternatE85 is a mixture of approximately 85% fuel ethanol and ing between E85 and unleaded gasoline is recom15% unleaded gasoline. mended. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank.
308 STARTING AND OPERATING • Some additives used in regular gasoline are not fully compatible with E85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as MOPAR威 Injector Cleanup or Techron may be used. Selection Of Engine Oil For Flexible Fuel Vehicles (E85) and Gasoline Vehicles FFV vehicles operated on E85 require specially formulated engine oils.
STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. CAUTION! ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
310 STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap may cause the “Malfunction Indicator Light (MIL)” to turn on.
STARTING AND OPERATING 311 Loose Filler Cap Message If the vehicles diagnostic system determines that the fuel • Never add fuel when the engine is running. This is filler cap in loose, improperly installed, or damaged, a in violation of most state and federal fire regula- “gASCAP” message will be displayed in the instrument tions and doing so will cause the MIL to turn on. cluster. Tighten the gas cap until a “clicking” sound is • A fire may result if gasoline is pumped into a heard.
312 STARTING AND OPERATING The label contains the following information: • Name of manufacturer • Month and year of manufacture • Gross Vehicle Weight Rating (GVWR) • Gross Axle Weight Rating (GAWR) front • Gross Axle Weight Rating (GAWR) rear • Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN).
STARTING AND OPERATING Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to insure that it is not over the GVWR.
314 STARTING AND OPERATING To maintain warranty coverage, follow the requirements Gross Trailer Weight (GTW) and recommendations in this manual concerning ve- The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temhicles used for trailer towing. porary) loaded in or on the trailer in its ⬙loaded and If you have any questions or concerns after reviewing ready for operation⬙ condition.
STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for further information. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded.
316 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. Trailer Hitch Classification Definitions Class Max.
STARTING AND OPERATING 317 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum Trailer Weight Ratings Max. GTW Max. Trailer Tongue Wt. Engine/Transmission Max. Frontal Area (Gross Trailer Wt.) (See Note 1) 2.4L/Auto See Note 2 1,000 lbs (450 kg) 100 lbs (45 kg) 2.7L/Auto See Note 2 1,500 lbs (680 kg) 150 lbs (68 kg) 3.5L/Auto 22 sq.ft. (2.0 sq.
318 STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for the maximum combined weight of occupants and cargo for your vehicle.
320 STARTING AND OPERATING WARNING! WARNING! (Continued) Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and that it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING WARNING! (Continued) 3. GAWR 4. Trailer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve 10% of trailer tongue weight as a percentage of total trailer weight). 321 • Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires – General Information” in “Starting and Operating” for information on tread wear indicators and for proper inspection procedure.
322 STARTING AND OPERATING • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • Trailer brakes are recommended for trailers over 1,000 lbs (450 kg) and required for trailers in excess of 2,000 lbs (907 kg).
STARTING AND OPERATING 323 If you REGULARLY TOW a trailer for more than 45 minutes of continuous operation, then change the automatic transmission fluid and filter according to the interval specified for “police, taxi, fleet, or frequent trailer towing.” Refer to “Maintenance Schedule” for the proper Make sure all trailer and vehicle lights are working maintenance intervals. properly — including hazard flashers.
324 STARTING AND OPERATING • Use speed control in flat terrain and with light loads to RECREATIONAL TOWING maximize fuel efficiency. (BEHIND MOTORHOME, ETC.) Cooling System Towing This Vehicle Behind Another Vehicle To reduce potential for engine and transmission over- (Flat towing with all four wheels on the ground) heating, take the following actions: • City Driving When stopped for short periods of time, shift the transmission into NEUTRAL and increase engine idle speed. • Highway Driving Reduce speed.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 327 ▫ Preparations For Jacking . . . . . . . . . . . . . . . 330 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 327 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 330 ▫ Engine Oil Overheating 䡵 Jump-Starting . . . . . . . . . . . (2.4L Engine Only) — If Equipped . . . . . . . . 328 ▫ Preparations For Jump-Start 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . .
326 WHAT TO DO IN EMERGENCIES 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 341 ▫ Towing With The Ignition Key . . . . . . . . . . . 341 ▫ Towing Without The Ignition Key . . . . . . . . 342 ▫ Towing This Vehicle Behind Another Vehicle . . . . . . . . . . . . . . . . . . . . . 342 ▫ Towing This Vehicle Behind Another Vehicle With A Tow Dolly . . . . . . . . . . . . . . . . . . . . 342 ▫ Towing Without Power — Override Transaxle Interlock System . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES 327 HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — Slow down.
328 WHAT TO DO IN EMERGENCIES NOTE: There are steps that you can take to slow down Engine Oil Overheating (2.4L Engine Only) — an impending overheat condition: If Equipped During sustained high-speed driving or trailer tow up • If your air conditioner (A/C) is on, turn it off. The A/C long grades on a hot day, the engine oil temperature may system adds heat to the engine cooling system and become too hot. If this happens, the “HOTOIL” message turning the A/C off can help remove this heat.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only.
330 WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Set the parking brake. 3. Place the shift lever into PARK (automatic transaxle) or REVERSE (manual transaxle). 4. Turn OFF the ignition. 5.
WHAT TO DO IN EMERGENCIES 331 WARNING! (Continued) WARNING! (Continued) • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack.
332 WHAT TO DO IN EMERGENCIES NOTE: The jack handle attaches to the side of the jack 2. Loosen, but do not remove, the wheel nuts by turning with two attachment points. When the jack is partially them to the left one turn while the wheel is still on the expanded, the tension between the two attachment ground. points holds the jack handle in place. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 3. 3.
WHAT TO DO IN EMERGENCIES 333 6 Front Jacking Location Rear Jacking Location 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. Do not raise the vehicle until you are sure the jack is securely engaged.
334 WHAT TO DO IN EMERGENCIES WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. 7. Lower the vehicle by turning the jack screw to the left. 5. Raise the vehicle by turning the jack screw to the right, using the swivel wrench.
WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 335 JUMP-STARTING If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack.
336 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations for Jump-Start The battery in your vehicle is located between the left front headlight assembly and the left front wheel splash shield. To allow jump-starting there are remote battery posts located on the left side of the engine compartment.
WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
338 WHAT TO DO IN EMERGENCIES WARNING! 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. 2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery.
WHAT TO DO IN EMERGENCIES 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 339 10. Reinstall the protective cover over the remote positive (+) battery post of the discharged vehicle.
340 WHAT TO DO IN EMERGENCIES front wheels. Then shift back and forth between REVERSE and FIRST gear. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective. NOTE: If your vehicle is equipped with Electronic Stability Control (ESC), turn the system to Partial OFF before attempting to “rock” the vehicle. Refer to “Electronic Brake Control” in “Starting and Operating” for further information.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE 341 CAUTION! (Continued) Towing With The Ignition Key Front Wheel Drive Your vehicle may be towed (with all four wheels flat on the ground), under the following conditions: • The shift lever must be in NEUTRAL. • The distance to be traveled must not exceed 15 miles (25 km). • The towing speed must not exceed 25 mph (40 km/h). CAUTION! • Exceeding these towing limits may cause a transaxle failure.
342 WHAT TO DO IN EMERGENCIES If you must use the accessories (wipers, defrosters, etc.) while being towed, the key must be in the ON position, not the ACC position. Make certain the transaxle remains in NEUTRAL. Towing Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. Flatbed towing is the preferred towing method. However, if a flatbed towing vehicle is not available, a wheel lift towing vehicle may be used.
WHAT TO DO IN EMERGENCIES 343 Towing Without Power — Override Transaxle • Insert the ignition key and rotate it to the ON position. Interlock System • Remove the cupholder liner. Special care must be taken when the vehicle is towed with the ignition in the LOCK position. A dolly should be • Insert a key, screwdriver, or similar object into the used under the front wheels if the rear wheels are raised.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.4L . . . . . . . . . . . . . 347 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 353 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 348 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 354 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 349 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 357 䡵 Onboard Diagnostic System — OBD II . . . . . . 350 ▫ Engine Air Cleaner Filter . . . . . . . . . .
346 MAINTAINING YOUR VEHICLE ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 364 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 389 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 364 ▫ Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 389 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 367 ▫ Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . 391 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 347 ENGINE COMPARTMENT — 2.
348 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.
MAINTAINING YOUR VEHICLE 349 ENGINE COMPARTMENT — 3.
350 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as maintaining engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE the gas cap is properly tightened. Press the trip odometer “Reset” button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the “Malfunction Indicator Light (MIL).” Resolving the problem will turn the MIL light off. 351 Normally, the OBD II system will be ready.
352 MAINTAINING YOUR VEHICLE 4. Approximately 15 seconds later, one of two things will system to update. A recheck with the above test routine happen: may then indicate that the system is now ready. a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.
354 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “Maintenance Schedule” for further information.
356 MAINTAINING YOUR VEHICLE CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. Engine Oil Viscosity (SAE Grade) – 2.4L and 2.7L Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle.
MAINTAINING YOUR VEHICLE 357 Lubricants which do not have both, the engine oil certi- Disposing of Used Engine Oil and Oil Filters fication mark and the correct SAE viscosity grade num- Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, ber should not be used. indiscriminately discarded, can present a problem to the Synthetic Engine Oils environment.
358 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed.
MAINTAINING YOUR VEHICLE 359 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
360 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a air conditioning refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment. 361 The A/C Air Filter is located in the fresh air inlet behind the glove box.
362 MAINTAINING YOUR VEHICLE 5. Disengage the two retaining tabs that secure the filter 7. Install the A/C Air Filter with the arrow on the filter cover to the HVAC housing and remove the cover. pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. CAUTION! The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 8.
MAINTAINING YOUR VEHICLE quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated.
364 MAINTAINING YOUR VEHICLE present please proceed to clean wiper blades with humid Exhaust System cloth removing any debris that may be affecting its The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust function. system. Adding Washer Fluid The fluid reservoir for the windshield washers is located If you notice a change in the sound of the exhaust system; in the engine compartment.
MAINTAINING YOUR VEHICLE 365 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
366 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
368 MAINTAINING YOUR VEHICLE Selection Of Coolant Use only the manufacturer’s recommended coolant. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
MAINTAINING YOUR VEHICLE replacement. To prevent reducing this extended maintenance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. 369 (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.
370 MAINTAINING YOUR VEHICLE WARNING! rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution.
MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill.
372 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
MAINTAINING YOUR VEHICLE Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed.
374 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident.
MAINTAINING YOUR VEHICLE 375 driven at least 15 miles (24 km). Hot fluid cannot be held Fluid Level Check – 2.4L and 2.7L Engines Use the following procedure to check the automatic comfortably between the fingertips. Cold fluid is at a transmission fluid level properly: temperature below 80°F (27° C). 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds. 3. Apply the parking brake fully. 4.
376 MAINTAINING YOUR VEHICLE CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. • Dirt and water in the transmission can cause serious damage.
MAINTAINING YOUR VEHICLE CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. 377 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
378 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove.
MAINTAINING YOUR VEHICLE 379 • If you detect any stone chips or scratches in the paint, Wheel and Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and chrome-plated wheels, should be cleaned regularly with considered the responsibility of the owner. a mild soap and water to prevent corrosion.
380 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and • For grease stains, apply MOPAR威 Multi-Purpose reducing light output, avoid wiping with a dry cloth. To Cleaner or equivalent to a clean, damp cloth and remove road dirt, wash with a mild soap solution folremove the stain. Use a fresh, damp towel to remove lowed by rinsing. soap residue.
MAINTAINING YOUR VEHICLE if absolutely necessary. Do not use harsh cleaners or Armor All威. Use MOPAR威 Total Clean or equivalent to clean vinyl upholstery. Cleaning Leather Upholstery MOPAR威 Total Clean or equivalent is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
382 MAINTAINING YOUR VEHICLE Dry with a soft tissue. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are Cleaning Center Console Cupholders molded in clear plastic. When cleaning the lenses, care Removal must be taken to avoid scratching the plastic. Grab the rubber portion of the cupholder and lift 1. Clean with a wet, soft rag. A mild soap solution may be upward. used, but do not use high alcohol content or abrasive cleaners.
MAINTAINING YOUR VEHICLE FUSES Totally Integrated Power Module (TIPM) The TIPM is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location.
384 MAINTAINING YOUR VEHICLE Cavity 6 Cartridge Fuse — 7 — 8 — 9 40 Amp Green Mini Fuse Description Ignition Off Draw (IOD) – 10 Amp Red Power Mirror Switch/Climate Controls Ignition Off 30 Amp Draw (IOD) Green Sense 1 Ignition Off 30 Amp Draw (IOD) Green Sense 2 Battery Feed – Power Seats – If Equipped/PZEV Air Pump – If Equipped Cavity Cartridge Fuse 10 — 11 — 12 — 13 — 14 — Mini Fuse Description Battery Feed – Cabin Compartment Node (CCN) 15 Amp Lt Selectable Power Blue Outle
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 15 40 Amp Green 16 — 17 — 18 40 Amp Green Mini Fuse Description Battery Feed – Radiator Fan Relay IGN Run/ACC – 15 Amp Lt. Cigar Lighter/ Blue PWR Sunroof Mod Ignition Off Draw (IOD) – Wireless Control 10 Amp Red Module (WCM)/ Clock/Steering Control Module (SCM) Battery Feed – — Auto Shutdown (ASD) Relay — Cartridge Fuse Mini Fuse 19 — 20 Amp Yellow 20 — 15 Amp Lt. Blue 21 — 10 Amp Red 22 — 10 Amp Red 23 — 15 Amp Lt.
386 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 24 — 25 — 26 — 27 — Mini Fuse Description Battery Feed — PWR Sunroof Feed Ignition Run — 10 Amp Red Heated Mirrors If Equipped Auto Shutdown 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 33 — 34 30 Amp Pink Mini Fuse Description Battery Feed – Switch Bank/ Diagnostic Link 10 Amp Red Connector/ Powertrain Control Module (PCM) Battery Feed – Anti-Lock Brakes (ABS) Module – If Equipped/ — Electronic Stability Control (ESC) Module – If Equipped Cavity Cartridge Fuse Mini Fuse 35 40 Amp Green — 36 30 Amp Pink — — 25 Amp Natural 37 387 Description Battery Feed – Anti-Lock Brakes (ABS) Module – If Equipped/ Electronic Stability
388 MAINTAINING YOUR VEHICLE CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Totally Integrated Power Module, and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
MAINTAINING YOUR VEHICLE LIGHT BULBS – Exterior Bulb No. Low Beam Headlamp . . . . . . . . . . . . . . . . . . . . . H11 High Beam Headlamp . . . . . . . . . . . . . . . . . . . . 9005 Front Park/Turn Signal/Side Marker Lamp . . . . 3757A Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . . PSX24W Center High Mounted Stop (CHMSL) Lamp . . . . . . . . . . . . . . . . . . . W16W (921) Rear Tail/Stop Lamp . . . . . . . . . . . . . . . . . . . . . 3157 Rear Turn Signal Lamp. . . . . . . . . . . . . . . .
390 MAINTAINING YOUR VEHICLE 3. Rotate bulb and connector 1⁄4 turn and pull outward 4. Pull the bulb out of the socket and replace the bulb. from assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 6. Reinsert the bulb and socket assembly and rotate clockwise 1⁄4 turn to secure.
MAINTAINING YOUR VEHICLE Fog Lamps 391 3. Rotate the bulb and connector 1⁄4 turn counterclockwise. 1. Access to the lamps through the lower fascia cutout is limited. 4. Pull the bulb off of connector and replace with a new one. 2. Turn the steering wheel to allow access and remove the inner fender shield. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol.
392 MAINTAINING YOUR VEHICLE Taillamps, Rear Turn Signals and Backup Lamps The turn signal, brake, taillamps and backup lamps are located in the rear corner body panel housing. 2. Remove the two plastic wing nuts from the taillamp housing. 1. Open the trunk and gently pull back the trunk liner behind the taillamp.
MAINTAINING YOUR VEHICLE 393 4. Twist and remove socket from lamp. 5. Remove bulb from socket and replace. 3. Grasp the taillamp and pull firmly outward pushing gently on the studs from inside to disengage the lamp housing.
394 MAINTAINING YOUR VEHICLE License Plate Lamp 2. Gently pry the lamp assembly loose. 1. Remove two retaining screws holding the light lens in 3. Pull bulb from socket, replace and reattach the lamp place. assembly with the two retaining screws. Center High-Mounted Stop Lamp 1. Open the trunk lid to find the centrally located highmounted stop lamp. 2. Twist and remove socket from the back of the lamp housing.
MAINTAINING YOUR VEHICLE 3. Replace the bulb and reinstall the socket into the housing by locking it in place with a twist.
396 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Fuel (Approximate) All Engines — (Except 2.4L PZEV) 16.9 Gallons 2.4L PZEV (Partial Zero Emissions Vehicle) 18.5 Gallons Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 2.7L Engine (SAE 5W-20, API Certified) 5.5 Quarts 3.5L Engine (SAE 10W-30, API Certified) 5.5 Quarts Cooling System* 2.4L Engine (MOPAR威 Antifreeze/Coolant 5 7.7 Quarts Year/100,000 Mile Formula or equivalent) 2.7L Engine (MOPAR威 Antifreeze/Coolant 5 9.
MAINTAINING YOUR VEHICLE 397 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 2.4L and 2.7L Engines Engine Oil – 3.5L Engine Engine Oil Filter Spark Plugs – 2.4L Engine except PZEV* Spark Plugs – 2.4L Engine with PZEV* Spark Plugs – 2.7L Engine Spark Plugs – 3.5L Engine Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
398 MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Genuine Part Fuel Selection – 2.4L and 2.7L En87 Octane gines Fuel Selection – 3.5L Engine 87 Octane Acceptable – 89 Octane Recommended * PZEV = Partial Zero Emission Vehicle Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 DOT 3 and SAE J1703 should be used.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 400 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 400 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 400 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever comes first.
M A I N T E N A N C E 402 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. • Inspect the battery and clean and tighten the terminals as required. Required Maintenance Intervals Refer to the Maintenance Schedules on the following • Check the fluid levels of coolant reservoir, brake pages for the required maintenance intervals.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 403 M 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 404 MAINTENANCE SCHEDULES A I 18,000 Miles (30,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Adjust parking brake on vehicles equipped with four wheel disc brakes.
M 406 MAINTENANCE SCHEDULES A I 42,000 Miles (70,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.4L Engine except PZEV*). Inspect the brake linings, and replace as necessary. Replace the air conditioning filter (if equipped).
M 408 MAINTENANCE SCHEDULES A I 66,000 Miles (110,000 km) or N T 66 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped).
M 410 MAINTENANCE SCHEDULES A I 90,000 Miles (150,000 km) or N T 90 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Inspect and replace the PCV valve, if necessary†. ❏ Adjust parking brake on vehicles equipped with four wheel disc brakes.
MAINTENANCE SCHEDULES 102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the spark plugs (2.4L PZEV*, 2.7L and 3.5L Engines). ❏ Replace the timing belt (3.5L Engine). ❏ Flush and replace the engine coolant. ❏ Inspect accessory drive belt, replace if necessary.
M 412 MAINTENANCE SCHEDULES A I 114,000 Miles (190,000 km) or N T 114 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.
MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 413 M 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 414 MAINTENANCE SCHEDULES A I 138,000 Miles (230,000 km) or N T 138 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Adjust parking brake on vehicles equipped with four wheel disc brakes.
M A I N T E N A N C E S C H E D U L E S 8 416 MAINTENANCE SCHEDULES * PZEV = Partial Zero Emission Vehicle † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 421 ▫ Prepare For The Appointment . . . . . . . . . . . 419 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 421 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 419 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
418 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 425 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 425 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 425 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 419 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
420 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 Auburn Hills, MI 48321–8004 solved with this process. Phone: (800) 423–6343 • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center P.O. Box 1621 ship. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
422 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. 423 Transport Canada, Motor Vehicle Defect Investigations and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B 3V9.
424 IF YOU NEED CONSUMER ASSISTANCE vehicle, system, and/or components is written in • Owner’s Manuals straightforward language with illustrations, diagrams, These Owner’s Manuals have been prepared with the and charts. assistance of service and engineering specialists to • Diagnostic Procedure Manuals acquaint you with specific Chrysler Group LLC vehicles.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. 425 significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
426 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
428 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 259 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 262 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 368 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 364 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 303 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 358 Air Conditioner Maintenance . . . . . . . . . .
INDEX 429 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 278 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 265 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . 259 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . . . 262 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 372,398 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 372 Parking . . . . . . .
430 INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 Oil (Engine) . . . . . . . . . . . . . . . . . . 347,348,349,356 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 259 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 369 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378 Carbon Monoxide Warning . . . . . . . . . . . . . . . 81,304 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . 135 Cargo Compartment . .
INDEX Contract, Service . . . . . . . . . . . . . . . . . . . . . . . . 421 Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . 369 Cooler, Beverage . . . . . . . . . . . . . . . . . . . . . . . . 140 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 367 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 368 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 396 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 367,370 Disposal of Used Coolant . . . . . . . . . . .
432 INDEX Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 30 Emergency Trunk Release . . . . . . . . . . . . . . . . . 37,38 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 121 Emission Control System Maintenance . . . . . . 351,400 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 347,348,349 Driving Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 358 On Slippery Surfaces . . . . . . . . . . . . . . . . . . . 255 Block Heater . . . . . . . . . . . . .
INDEX 433 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 376 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . 355,396 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 357,397 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 357 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 357 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 Flashers . . . . . . . . . . .
434 INDEX Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . 375,376 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372,398 Cooling System . . . . . . . . . . . . . . . . . . . . . . . 367 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 354 Power Steering . . . . . . . . . . . . . . . . . . . . . 259,398 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 397 Fog Lights . .
INDEX 435 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 389 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 High Beam . . . . . . . . . . . . . . . . . . . . . . . . 109,163 High Beam/Low Beam Select Switch . . . . . . . . 109 On With Wipers . . . . . . . . . . . . . . . . . . . . . . . 116 Passing . . . . . . . . . . . . . . . .
436 INDEX Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . 12 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 19 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 14 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . 69,70,71 Information Center, Vehicle . . . . . . . . . . . . . . . . . 164 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 89 Instrument Cluster . . . . . . . . . . . . . . . . . . . .
INDEX 437 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 107 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . 84,388 Lights On Reminder . . . . . . . . . . . . . . . . . . . . 110 Lights . . . .
438 INDEX Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . 372 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 167 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Automatic Dimming . . . . . . . . . . . . . . . . . . . . . 90 Electric Powered . . . . . . . . . . . . . . . . . . . . . . . 90 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Rearview . . . . . . .
INDEX Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154,157 Oil Change Indicator . . . . . . . . . . . . . . . . 156,166,400 Oil Change Indicator, Reset . . . . . . . . . . . . . . 156,166 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 354,397 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 Change Interval . . . . . . . . . . . . . . . 156,166,355,400 Checking . . . . . . . . . . . .
440 INDEX Radio Remote Controls . . . . . . . . . . . . . . . . . . . . 222 Radio, Satellite (Uconnect威 studios) . . . . . . . . . . . 215 Rear Cupholder . . . . . . . . . . . . . . . . . . . . . . . . . 134 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . 103,104 Rear Window Defroster . . . . . . . . . . . . . . . . . . . 139 Rear Window Features . . . . . . . . . . . . . . . . . . . . 139 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 89 Recreational Towing . . . . . . . . .
INDEX Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . 388 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 15 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 352 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 288 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 422 Resetting Oil Change Indicator . . . . . . . . . . . 156,166 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Restraints, Child . . . . . . . .
442 INDEX Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 96 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Rear Folding . . . . . . . . . . . . . . . . . . . . . . . 103,104 Rear Folding (Sedan) . . . . . . . . . . . . . . . . . . . 135 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134,388 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 235 Stuck, Freeing . . . . . . . . . . . . . . . . . . . . . . . . . . 339 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Supplemental Restraint System - Airbag . . . . . . . . 53 Synthetic Engine Oil . . . . . . . . . . . . . . .
444 INDEX Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 288 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 272,282 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 Spinning . . .
INDEX 445 Vehicle Identification Number (VIN) . . . . . . . . . . . . 6 Vehicle Loading . . . . . . . . . . . . . . . . . . . 279,311,313 Vehicle Modifications/Alterations . . . . . . . . . . . . . . 7 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 235,388 Vehicle Theft Alarm (Security Alarm) . . . . . . . . . . 17 Video Entertainment System™ (Rear Seat Video System) . . . . . . . . . . . . . . . . . . 220 Viscosity, Engine Oil . . . . . . . . . . . . . . . . . . . . . .
446 INDEX Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 379 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 379 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 36,129 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 236 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Windshield Defroster . . . . . . . . . . . . . . . . 82,227,233 Windshield Washers . . . . . .
Chrysler Group LLC 10D41-126-AC 3rd Edition Printed in U.S.A.
