CHA LLE NG ER 2009 CHALLENGER 2009 OWNER’S MANUAL Chrysler LLC 81-226-0916 147914 Dodge LC22 Challenger.indd 1 Second Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction .......................... 4 䡵 How To Use This Manual 䡵 Warnings And Cautions ................. 4 .................. 6 䡵 Vehicle Identification Number 䡵 Vehicle Modifications/Alterations ............. 6 ...........
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . 12 ▫ Wireless Ignition Node (WIN) ▫ FOB With Integrated Key ▫ Ignition Key Removal . . . . . . . . . . . . . . 13 . . . . . . . . . . . . . . . . . 13 ▫ Key-In-Ignition Reminder 䡵 Sentry Key威 . . . . . . . . . . . 12 . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . . . . . . . . . 15 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Open The Trunk . . . . . . . . . . . . . . . . . . 24 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . 24 ▫ Programming Additional Transmitters ▫ Transmitter Battery Service . . . . . 25 . . . . . . . . . . . . . 25 ▫ General Information . . . . . . . . . . . . . . . . . . 26 䡵 Remote Starting System . . . . . . . . . . . . . . . . . 26 ▫ How To Use Remote Start 䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Event Data Recorder (EDR) ▫ Child Restraint . . . . . . . . . . . . . 56 . . . . . . . . . . . . . . . . . . . . . . 58 䡵 Engine Break-In Recommendations 䡵 Safety Tips . . . . . . . . . 67 . . . . . . . . . . . . . . . . . . . . . . . . . . 68 ▫ Transporting Passengers . . . . . . . . . . . . . . . 68 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . 68 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Fob with Integrated Key and a Wireless Ignition Node (WIN) with an integral ignition switch. You can insert the double-sided integrated key into the ignition switch with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Fob With Integrated Key The Fob with Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a valet key, which stores in the rear of the Fob. 2 The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead. The valet key is also for locking the glove box. You can keep the valet key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The power window switches, radio, power sunroof (if equipped), and ignition-powered power outlets will remain active for up to 60 minutes after the ignition switch is turned to the LOCK position. Opening either door will cancel this feature. The time for this feature is programmable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses the factory-mated Remote Keyless Entry (RKE) transmitter with integrated key and Wireless Ignition Node (WIN) to prevent unauthorized vehicle operation.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: Only RKE transmitters that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a transmitter is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! Always remove the keys from the vehicle and lock all doors when leaving the vehicle unattended. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 2. Insert the second valid integrated key and turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound and the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key. 3. Insert a blank integrated key into the ignition switch and turn the ignition switch to the ON position within 60 seconds.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM The Vehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation. If something triggers the alarm, the Vehicle Security Alarm will prevent the vehicle from starting and provide the following audible and visible signals: the horn will pulse; the headlights will flash; the park lights will flash; and the Vehicle Security Light in the instrument cluster will flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: • The driver’s door key cylinder and the trunk button on the RKE transmitter cannot arm or disarm the Vehicle Security Alarm. • The Vehicle Security Alarm remains armed during trunk entry. Pressing the TRUNK button will not disarm the Vehicle Security Alarm. If someone enters the vehicle through the trunk, and opens any door, the alarm will sound. • When the Vehicle Security Alarm is armed, the interior power door lock switches will not unlock the doors.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned ON from the LOCK position. NOTE: • None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To Unlock The Doors Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice within five seconds, to unlock both doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lights with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the transmitter. This feature can be turned on or turned off. Refer to “Flash Lights with Remote Key Lock,” under ⬙Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4. • When not using the EVIC, perform the following steps: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Headlights On with Remote Key Unlock,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4. 1. Press the LOCK button on a programmed transmitter for at least four seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button. To Lock The Doors Press and release the LOCK button on the transmitter to lock both doors.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Express Down Window Feature This feature allows you to remotely lower both door windows at the same time. To use this feature, press and release the UNLOCK button on the transmitter and then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely. To Open The Trunk Press the TRUNK button on the transmitter two times within five seconds to open the trunk.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Programming Additional Transmitters Refer to Sentry Key威 “Customer Key Programming.” If you do not have a programmed RKE transmitter, contact your authorized dealer for details. 2 Transmitter Battery Service The recommended replacement battery is one CR2032 battery. NOTE: • Perchlorate Material — special handling may apply. See www.dtsc.ca.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Reposition the access door panel over the battery opening and snap into place. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Doors closed • Hood closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level, and • RKE PANIC button not pressed. To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will chirp twice (if programmed).
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shut downs, the system will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote Start request. To Exit Remote Start Mode and Drive the Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! Door Lock Plunger If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure the key is not inside the vehicle before closing the door. • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key from the ignition and lock your vehicle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE is open, the key is in the ignition, and the ignition is in the LOCK or ACC position, a chime will sound as a reminder to remove the key. Automatic Door Locks The doors will lock automatically if all of the following conditions are met: 1. The Automatic Door Locks feature is enabled 2. The transmission is in gear 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Automatic Door Locks — If Equipped The auto door lock feature can be enabled or disabled by your authorized dealer. See your authorized dealer for programming. Automatic Unlock Doors on Exit The doors will unlock automatically if: 1. The Automatic Unlock Doors On Exit feature is enabled 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h) 3. The transmission is in NEUTRAL or PARK 4. The driver door is opened 5.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. A single chime will indicate the completion of the programming. NOTE: If you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the procedure. 6. Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Automatic Unlock Doors On Exit feature in accordance with local laws.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: • The door window will lower slightly if it is closed completely when opening the door. The window will return to its fully closed position after closing the door. This action allows the door to open without resistance and prevents window and seal damage. • You can remotely lower both the driver side and passenger side windows at the same time. Refer to “Remote Keyless Entry/Express Down Window Feature” in this section.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with one window open, then open the other window to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 With the ignition switch in the ON position, the Trunk Open symbol will display in the instrument cluster indicating that the trunk is open. The odometer display will reappear once the trunk is closed. With the ignition switch in the LOCK position or the key removed from the ignition switch, the Trunk Open symbol will display until the trunk is closed.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Emergency Release Emergency Release The trunk of your vehicle is equipped with an emergency release handle. It is located on the inside of the trunk lid, near the latch, and is coated so that it glows in a darkened trunk. Pull on the handle to open the trunk. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 2. The seat belt latch plate is contacting the seat when the belt is routed through the seat web guide. When the belt is routed outside of the seat web guide, the latch plate will contact the quarter trim panel. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snug.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt cannot do its job as well. In a collision, it could even cut into you. Be sure the belt is straight. If you cannot straighten a belt in your vehicle, take it to your authorized dealer and have it fixed. 5.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snug and positioned properly. The pretensioners are triggered by the Occupant Restraint Controller (ORC). (Refer to information on Airbags in this section). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: You must perform the following steps within 60 seconds of turning the ignition switch to the ON position. NOTE: When the BeltAlert威 is deactivated, the Seat Belt Reminder Light will continue to illuminate as long as the driver’s seat belt is unbuckled. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver’s seat belt at least three times, ending with the seat belt buckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 3. Allow the belt to retract. As the belt retracts, you will here a clicking sound. This indicates the safety belt is now in the Automatic Locking mode. How to Disengage the Automatic Locking Mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the Automatic Locking mode and activate the vehicle sensitive (emergency) locking mode.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver side front airbag is mounted in the center of the steering wheel. The passenger side front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 The front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. This vehicle is also equipped with supplemental side curtain airbags (located above the side windows) to protect the driver and passenger sitting next to a window. Their covers are also labeled SRS AIRBAG. WARNING! • Do not put anything on or around the front airbag covers or attempt to open them.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not stack luggage or other cargo up high enough to block the location of the side curtain airbag. The area where the side curtain airbag is located should remain free from any obstructions. • Do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment could cause severe injury or death to infants in that position. seat as far back as possible and use the proper child restraint. (Refer to information on Child Restraint in this section.) 5. You should read the instructions provided with your child restraint to make sure that you are using it properly. 6.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 • Interconnecting Wiring • Seat Belt Reminder Light • Knee Impact Bolsters • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pretensioners How the Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. The front airbag inflators are designed to provide different rates of airbag inflation from direction provided by the ORC.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • The Driver and Front Passenger Airbag/Inflator Units are located in the center of the steering wheel and the passenger side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 inflating side curtain airbag pushes the outside edge of the headliner out of the way and covers the window. The airbag inflates in about 30 milliseconds (about one-quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side curtain airbag inflates. This especially applies to children.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have been deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags cannot protect you in another collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper passenger side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data parameters (see the following list) in an event data recorder prior to the moment of airbag deployment, or near deployment, and up to a quarter second of high-speed deceleration data during and/or after airbag deployment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavailable. NOTE: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the U.S. government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status • Traction/stability control status • Tire Pressure Monitoring System status (if equipped) Child Restraint Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Infants and Child Restraints • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing, infant carriers and convertible child seats. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg).
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and beltpositioning booster seat are held in the vehicle by the lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 WARNING! (Continued) • A rearward-facing child restraint should only be used in a rear seat. A rearward-facing child restraint in the front seat may be struck by a deploying passenger airbag, which may cause severe or fatal injury to the infant. Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCH-compatible child restraint systems are now available. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation using the vehicle’s seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Installing the LATCH-Compatible Child Restraint System We urge you to follow the manufacturer’s directions carefully when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that are provided with the child restraint system.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE most direct path between the anchor and the child restraint. Finally, tighten all three straps as you push the child restraint rearward and downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instructions. NOTE: • Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight; however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. The seat belt must be in the Automatic Locking mode in order to enable a child restraint to be tightly installed.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Tether Strap Mounting 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the drivetrain (engine, transmission, and rear axle) in your new vehicle. Drive moderately during the first 500 mi (800 km). After the initial 60 mi (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 ▫ Automatic Dimming Inside Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 75 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . 76 ▫ Outside Mirrors Folding Feature ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . 76 ▫ Heated Mirrors — If Equipped ▫ Vanity Mirrors . . . . . . . . . 76 . . . . . . . . . . 77 . . . . . . . . . . . . . .
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 107 ▫ Voice Recognition System (VR) Operation ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . 109 ▫ Voice Training 䡵 Seats . . 107 . . . . . . . . . . . . . . . . . . . . . 112 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Easy Entry Seats ▫ Power Seats . . . . . . . . . . . . . . . . . . . . 112 . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 䡵 Windshield Wipers And Washers ▫ Intermittent Wiper System ▫ Mist Feature . . . . . . . . . 126 . . . . . . . . . . . . . 127 . . . . . . . . . . . . . . . . . . . . . . . 127 ▫ Windshield Washers . . . . . . . . . . . . . . . . . 127 ▫ Headlights On With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . 128 䡵 Tilt/Telescoping Steering Column 䡵 Electronic Speed Control ▫ To Activate . . . . . . . . . . . . . . . 129 . . . . .
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Power Sunroof — If Equipped . . . . . . . . . . . 140 ▫ Ignition Off Operation ▫ Opening Sunroof - Partially . . . . . . . . . . . . 141 ▫ Opening Sunroof - Express . . . . . . . . . . . . 141 䡵 Electrical Power Outlets ▫ Closing Sunroof - Partially . . . . . . . . . . . . 141 䡵 Cupholders ▫ Closing Sunroof - Express ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . 142 ▫ Pinch Protect Override . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 MIRRORS Automatic Dimming Inside Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. 3 Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror. NOTE: The passenger-side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle. WARNING! Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in this Section, for further information. Vanity Mirrors An vanity mirror is on the sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward.
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE visor, grab the extender which is located at the rear of the visor and pull rearward. Illuminated Vanity Mirror Slide On Rod and Extender Features of Sun Visor To use the slide on rod feature of the sun visor, rotate the sun visor downward and swing the sun visor so it is parallel to the side window, grabbing the sun visor with your left hand pull rearwards until the sun visor is in the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 uconnect姞 phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect威 phone. Refer to your “Navigation User’s Manual” for uconnect威 phone operating instructions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate. uconnect威 phone is a voice-activated, hands-free, invehicle communications system.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s uconnect威 phone. The uconnect威 phone allows up to seven cellular phones to be linked to the system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages. The uconnect威 phone can be used with any Hands-Free Profile certified Bluetooth威 cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Operation Voice commands can be used to operate the uconnect威 phone and to navigate through the uconnect威 phone menu structure. Voice commands are required after most uconnect威 phone prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the ⬙Ready⬙ prompt or another prompt.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cancel Command At any prompt, after the beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) uconnect威 phone to a Cellular Phone To begin using your uconnect威 phone, you must pair your compatible Bluetooth威 enabled cellular phone. To complete the pairing process, you will need to reference your cellular phone Owner’s Manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect威 phone will use the priority three cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to ⬙Advanced Phone Connectivity⬙ in this section). Dial by Saying a Number • Press the PHONE button to begin.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The uconnect威 system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add Names to Your uconnect威 Phonebook NOTE: Adding names to the uconnect威 phonebook is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Phonebook Download – Automatic Phonebook Transfer From Cellular Phone If equipped and specifically supported by your phone, uconnect威 phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific Bluetooth威 Phones with Phone Book Access Profile may support this feature. See uconnect威 website for supported phones.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download — Single Entry If equipped and supported by your phone, uconnect威 phone allows the user to download entries from their phone via Bluetooth威. To use this feature, press the PHONE button and say “Phonebook Download.” The system prompts, “Ready to accept “V” card entry via Bluetooth威…” The system is now ready to accept phonebook entries from your phone using the Bluetooth威 Object Exchange Profile (OBEX).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, cellular, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the uconnect威 phone will ask you which designation you wish to delete: home, work, cellular, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited. Delete/Erase “All” uconnect威 Phonebook Entries • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • The uconnect威 phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the uconnect威 phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the uconnect威 phone.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section. Place/Retrieve a Call From Hold To put a call on hold, press the PHONE button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the PHONE button until you hear a single beep.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • After the ⬙Ready⬙ prompt and the following beep, say ⬙Redial.⬙ • The uconnect威 phone will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the uconnect威 phone. Call Continuation Call continuation is the progression of a phone call on the uconnect威 phone after the vehicle ignition key has been switched to OFF.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every uconnect威 phone language change operation, only the language-specific 32-name phonebook is usable. The paired phone name is not languagespecific and usable across all languages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • The uconnect威 phone does slightly lower your chances of successfully making a phone call as to that for the cell phone directly. WARNING! Your phone must be turned on and paired to the uconnect威 phone to allow use of this vehicle feature in emergency situations, when the cell phone has network coverage and stays paired to the uconnect威 phone. Towing Assistance If you need towing assistance: • Press the PHONE button to begin.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You can use your uconnect威 phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some services require immediate response selection. In some instances, that may be too quick for use of the uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is asking ⬙Would you like to pair a phone, clear a...,⬙ you could press the VOICE RECOGNITION button and say, ⬙Pair a Phone⬙ to select that option without having to listen to the rest of the voice prompt.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Certain brands of cellular phones do not send the dial ring to the uconnect威 phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 If you would like to connect or disconnect the Bluetooth威 connection between a uconnect威 phone paired cellular phone and the uconnect威 phone, follow the instructions described in your cellular phone User’s Manual. Select Another Cellular Phone This feature allows you to select and start using another phone paired with the uconnect威 phone.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete uconnect威 phone Paired Cellular Phones • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete⬙ and follow the prompts. • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 This procedure may be repeated with a new user. The system will adapt to the last trained voice only. • Performance is maximized under: To restore the Voice Recognition system to factory default settings, enter the Voice Training session via the above procedure and follow the prompts.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • It is not recommended to store similar sounding names in the uconnect威 phonebook. • Phonebook (Downloaded and uconnect威 phone Local) name recognition rate is optimized when the entries are not similar. • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Bluetooth威 Communication Link Cellular phones have been found to lose connection to the uconnect威 phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Your cellular phone is recommended to remain in Bluetooth威 ON mode. Power-Up After switching the ignition key from OFF to either the ON or ACC position, or after a language change, you must wait at least five seconds prior to using the system.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 3
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 3
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call uconnect威 Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command. Pressing the VR button while the system is speaking is known as “barging in.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Commands The Voice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Recognition system is speaking.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio FM To switch to the FM band say “FM” or “Radio FM”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Memo To switch to the voice recorder mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording you may press the VR button to stop recording. You proceed by saying one of the following commands: − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup say “Setup”.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, uconnect威 phone Voice Training feature may be used. 1. Press the VR button, say “System Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 used to adjust the angle of the seatback. Push forward or rearward on the switch to change the position of the seatback. 3 Easy Entry Seats Power Seats The power seat switches are on the outboard side of the front seat cushions. The power seat switch can be moved forward and backward as well as up and down to control the position of the seat.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Recline Lever Manual Front Seatback Recline To recline: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support. Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraint so that the upper edge is as high as practical. To raise it, pull upward on the head restraint.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats The driver seat and front passenger seat are heated. The heaters provide the same heat level for both cushion and seatback. The controls for each heater are located near the bottom center of the instrument panel. After turning on the ignition, you can choose from High, Low, or Off heat settings. Amber indicators in the top portion of each switch indicate the level of heat in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 If high level heating is selected, the system will automatically switch to the low level after 30 minutes of continuous operation. At that time, the number of indicators illuminated changes from two to one, indicating the change. Operation on the low setting also turns off automatically after 30 minutes. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Rear Folding Seat When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO (A) position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch OFF.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. The Headlights On with Wipers feature can be enabled or disabled. Refer to ”Headlights On with Wipers,” under “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver when the driver’s door is opened. Fog Lights — If Equipped The front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the corresponding turn signal indicator in the instrument cluster flashes to show proper operation of the front and rear turn signal lights. You can also signal a lane change by moving the multifunction lever partially up or down without moving beyond the detent. Releasing the multifunction lever at the detent will provide three flashes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. Dimmer Control Overhead Console Interior Lights The interior lights come on when a door is opened. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. the ON position. The multifunction lever is located on the left side of the steering column. Interior Light Defeat (OFF) Rotate the dimmer control to the extreme bottom off position. The interior lights will remain off when the doors are open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 CAUTION! WARNING! Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper switch is left in any position other than off. Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you activate the washer while the windshield wiper control is in the delay range, the wipers will operate for two wipe cycles after releasing the multifunction lever and then resume the intermittent interval previously selected. The Headlights On with Wipers feature can be enabled or disabled. Refer to ”Headlights On with Wipers,” under “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged. WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The indicator light in the instrument cluster will illuminate to show that the speed control system is on. To turn the system off, push and release the ON/OFF button again. The system and the indicator light will turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 To Set At A Desired Speed When the vehicle reaches the speed desired, push the lever downward to SET DECEL and release. Remove your foot from the accelerator pedal and the vehicle will operate at the selected speed. NOTE: • Electronic Speed Control will only function in 3rd, 4th, or 5th gear when in the Autostick威 mode (if equipped). • Electronic Speed Control may not engage if a different size tire is installed on one wheel, such as the compact spare tire.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the lever to RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase. Each time the lever is tapped speed increases, so tapping the lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while Electronic Speed Control is set, push down and hold the lever in SET DECEL. Release the lever when the desired speed is reached, and a new set speed will be established.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions and you could lose control. An accident could be the result. Don’t use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE These lights also turn on when a door is opened, or when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer control is turned fully upward, past the second detent. The HomeLink威 buttons are located in the overhead console, and contain one, two, or three dots/lines designating the different HomeLink威 channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. For optimal training, point the battery end of the handheld transmitter away from the HomeLink威. 4. Press and hold the just-trained HomeLink威 button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with Programming HomeLink威 Step 2 and follow all remaining steps.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. 1. This device may not cause harmful interference 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the switch in the forward position, the sunroof will close fully and then stop automatically. Release the switch once the sunroof stops moving. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called Express Close. During Express Close operation, any movement of the sunroof switch will stop the sunroof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. Front Power Outlet The center console outlet is powered directly from the battery (power available at all times).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 CAUTION! CAUTION! (Continued) • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Cupholders The front cupholders are located in the center console. Illuminated Front Cupholders — If Equipped The front cupholders are illuminated with LEDs. They are turned on with the headlights or parking lights. Refer to “Interior Lights” under “Lights” in Section 3. Rear Cupholders The rear seat cupholders are located in the center armrest between the rear seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 CONSOLE FEATURES Sliding Center Console Armrest The center console armrest slides forward with three detents to provide flexibility for comfort, cupholder use, and shifting ease.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Storage The center console has a storage compartment located underneath the armrest, and also contains a 12-Volt power outlet, a molded-in coin holder (designed to hold various size coins). The center console may also be equipped with a Universal Consumer Interface (UCI). UCI supports Mini, 4G, Photo, Nano, 5G iPod威 and iPhone威 devices. Refer to “Universal Consumer Interface (UCI) — If Equipped” in Section 4 for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 REAR WINDOW FEATURES Rear Window Defroster The pushbutton for the rear window defroster is located on the mode knob of the climate control switch bank. Press this button to turn on the rear window defroster and the electric remote control heated mirrors (if equipped). An amber light shows that the defroster is on. The defroster will automatically turn off after approximately 10 minutes. For an additional five minutes of operation, press the switch again.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . 155 ▫ Trip Functions 䡵 Instrument Cluster – Base . . . . . . . . . . . . . . 156 ▫ Keyless Go Display — If Equipped . . . . . . . . . . . . . . . . . . . . . 173 . . . . . . 175 䡵 Instrument Cluster – Premium . . . . . . . . . . . 157 ▫ Compass Display 䡵 Instrument Cluster Description . . . . . . . . . . . 158 ▫ Driver-Selectable Surround Sound (DSS) – If Equipped . . . . . . . . . . . . . . . .
152 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD Changer (MP3/WMA AUX Jack) . . . 182 ▫ Operating Instructions - Radio Mode . . . . . 182 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play) . . . . . . . . . . . . 187 ▫ Notes On Playing MP3/WMA Files . . . . . . 189 ▫ Operating Instructions — uconnect威 phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 194 ▫ Clock Setting Procedure . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 153 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 211 ▫ Notes On Playing MP3 Files . . . . . . . . . . . 213 ▫ List Button (CD Mode For MP3 Play) . . . . . 216 ▫ Info Button (CD Mode For MP3 Play) . . . . 216 䡵 Universal Consumer Interface (UCI) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 217 ▫ Connecting The iPod威 ▫ Using This Feature . . . . . . . . . . . . . . . . 218 . . . . . . . . . . . . .
154 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Kicker威 High Performance Sound System With Driver-Selectable Surround (DSS) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 227 䡵 Remote Sound System Controls 䡵 CD/DVD Disc Maintenance . . . . . . . . . . 228 . . . . . . . . . . . . . 229 䡵 Radio Operation And Cellular Phones . . . . . . 230 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . 230 ▫ Manual Air Conditioning And Heating System . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 155 INSTRUMENT PANEL FEATURES 4 1 2 3 4 - Air Outlets - Instrument Cluster - Glove Compartment - Radio 5 6 7 8 - Heated Seat Switch ESP OFF Switch Hazard Warning Switch Climate Control 9 - Ignition Switch 10 - Trunk Release Switch 11 - Headlight Switch
156 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 157 INSTRUMENT CLUSTER – PREMIUM 4
158 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Trip Odometer Button Press this button to change the display from odometer to either of two trip odometer settings. The letter “A” or “B” will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 miles (km). The odometer must be in TRIP mode to reset it. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 7. Electronic Throttle Control (ETC) Warning Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if there is a problem with the Electronic Throttle Control (ETC) system. If the light comes on while the engine is running, safely bring the vehicle to a complete stop as soon as possible, place the shift lever in PARK, and cycle the ignition key. The light should turn off.
160 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” and you hear a chime, turn the engine OFF immediately and call for service. WARNING! A hot engine cooling system is dangerous.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 11. Engine Temperature Warning Light This light will turn on and a single chime will sound to warn of an overheated engine condition. When this light turns on, the engine temperature is critically hot. If the light turns on while driving, safely pull over and stop the vehicle. The vehicle should be turned OFF immediately and serviced as soon as possible. (Refer to “If Your Engine Overheats” in Section 6 for more information). 12.
162 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 19. Odometer/Electronic Vehicle Information Center (EVIC) Display The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “Trip Odometer Button” for additional information. NOTE: U.S. Federal regulations require upon transfer of vehicle ownership, the seller certify the mileage the vehicle has been driven.
164 UNDERSTANDING YOUR INSTRUMENT PANEL the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position. To turn off the message temporarily, press and release the TRIP ODOMETER button on the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.
166 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 21. Vehicle Security Light — If Equipped This light will flash at a fast rate for approximately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. 22.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
168 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 26. Door Ajar Indicator This light will turn on to indicate that one or more door may be ajar. 27. Decklid Ajar Indicator This light will turn on to indicate that the decklid may be ajar. 4 28. Windshield Washer Fluid Low Indicator This light will turn on to indicate the windshield washer fluid is low.
170 UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle Information Warning Message Displays • Tire Pressure Monitor System • Personal Settings (Customer Programmable Features) • Compass Display • Outside Temperature Display • Trip Computer Functions • uconnect威 phone (If Equipped) • uconnect威 gps Screens (If Equipped) • Audio Mode Display • Surround Sound Modes (If Equipped with DriverSelectable Surround [DSS]) The system allows the driver to select information by pressing the following buttons mounted on the s
UNDERSTANDING YOUR INSTRUMENT PANEL 171 Features). The SCROLL button also functions as a remote sound system control. Refer to “Remote Sound System Controls” in this section. AUDIO MODE Button Press the AUDIO MODE button to select the Compass/Temp/Audio screen. Along with compass reading and outside temperature, this screen will display radio and media mode information depending on which radio is in the vehicle. Refer to “Remote Sound System Controls” in this section.
172 UNDERSTANDING YOUR INSTRUMENT PANEL • Channel # Trained • Wrong Key • Clearing Channels • Push Button or Insert Key/Turn To Run (refer to “Remote Starting System” in Section 2) • Channels Cleared • Did Not Train • Left Front Low Pressure (with a single chime) • Left Rear Low Pressure (with a single chime) • 1–4 SKIPSHIFT • Stereo (If Equipped with Driver-Selectable Surround Sound [DSS]) • Right Front Low Pressure (with a single chime) • Audio Surround (If Equipped with Driver-Selectable Surround
UNDERSTANDING YOUR INSTRUMENT PANEL 173 indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. Trip Functions Press and release the MENU button until one of the following Trip Functions displays in the EVIC: Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the MENU button.
174 UNDERSTANDING YOUR INSTRUMENT PANEL “RESET” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset. • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 To Reset The Display Reset will only occur while a resettable function is being displayed. Press and release the FUNCTION SELECT button once to clear the resettable function being displayed. To reset all resettable functions, press and release the FUNCTION SELECT button a second time within three seconds of resetting the currently-displayed function. (>Reset ALL will display during this three-second window.
176 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Under certain conditions, the display may be superseded by another display of higher priority. But when the ignition switch position is changed, the display always re-appears. Compass Display COMPASS Button The compass readings indicate the direction the vehicle is facing. Press and release the COMPASS button to display one of eight compass readings and the outside temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 5. Complete one or more 360 degree turns (in an area free from large metal or metallic objects) until the “CAL” message turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between magnetic North and geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
178 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the SCROLL button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4. Press and release FUNCTION SELECT button until the proper variance zone is selected according to the map. 5. Press and release the COMPASS button to exit. Driver-Selectable Surround Sound (DSS) – If Equipped Press and release the MENU button until “Surround Sound” displays in the EVIC. The EVIC provides information on the current surround mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 Press and release the MENU button until Personal Settings displays in the EVIC. Use the SCROLL button to display one of the following choices. Language When in this display you may select one of three languages for all display nomenclature, including the trip functions and the uconnect威 gps (if equipped). Press the FUNCTION SELECT button while in this display to select English, Espanol, or Francais.
180 UNDERSTANDING YOUR INSTRUMENT PANEL the doors will unlock on the first press of the RKE transmitter UNLOCK button. To make your selection, press and release the FUNCTION SELECT button until “Driver Door 1st Press” or “All Doors 1st Press” appears. Sound Horn with Remote Key Lock When ON is selected, a short horn sound will occur when the RKE transmitter LOCK button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 Hill Start Assist (HSA) — If Equipped When on is selected, the HSA system is active. Refer to “HSA (Hill Start Assistance)” under “Electronic Brake Control System” in Section 5 of this manual for system function and operating information. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
182 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next.
184 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. 5. To exit, press any button/knob or wait five seconds. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade.
186 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R & B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
188 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Rewind) button works in a similar manner. AM or FM Button (CD MODE) Switches the radio to the radio mode. Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited.
190 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3/ WMA playback may result in longer disc loading times. frequencies in the following table are supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files.
192 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the INFO button for three seconds or more and radio will display song titles for each file. Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Operating Instructions - uconnect威 studios (Satellite Radio) (If Equipped) Refer to “uconnect威 studios (Satellite Radio)” in this section. RW/FF (Auxiliary Mode) No function. Dolby威 Manufactured under license from Dolby威 Laboratories. ⬙Dolby威⬙ and the double-D symbol are trademarks of Dolby威 Laboratories.
194 UNDERSTANDING YOUR INSTRUMENT PANEL DTS™ ⬙DTS™⬙ and ⬙DTS™ 2.0⬙ are trademarks of Digital Theater Systems, Inc. AM/FM/CD/DVD RADIO (RER/REN) – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER radios contain a CD/DVD player, USB port, and a 30-gigabyte hard drive (HDD). Sirius Satellite Radio is optional. The 6.5 in (16.5 cm) touch screen allows for easy menu selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 To Manually Set the Clock — RER/REN 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed. The clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 5.
196 UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
198 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button to alternate locations of the time and frequency display. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
200 UNDERSTANDING YOUR INSTRUMENT PANEL SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations).
UNDERSTANDING YOUR INSTRUMENT PANEL 201 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels.
202 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. AM/FM Button Press the button to select either AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display.
204 UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rate. MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate.
206 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With uconnect” message will display on the radio screen. TIME Button Press the TIME button to alternate locations of the time and frequency display. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3.
208 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies Personality Public 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Persnlty Public Program Type Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display R&B Rel Mus
210 UNDERSTANDING YOUR INSTRUMENT PANEL station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station. SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC/AUX Button Pressing the DISC/AUX button will allow you to switch from AM/FM modes to DISC/AUX mode. Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio.
212 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 RW/FF Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. AM/FM Button Press the button to select either AM or FM mode.
214 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
216 UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is OFF). Operating Instructions - uconnect威 phone (If Equipped) Refer to “uconnect威 phone” in Section 3. Operating Instructions - uconnect威 studios (Satellite Radio) (If Equipped) Refer to “uconnect威 studios (Satellite Radio)” in this section.
218 UNDERSTANDING YOUR INSTRUMENT PANEL Connecting The iPod姞 Use the optional connection cable to connect an iPod威 to the vehicle’s 16–pin connector port located on the center console. Once the iPod威 is connected and synchronized to the vehicle’s UCI system (iPod威 may take a few seconds to connect), the iPod威 starts charging and is ready for use by pressing radio switches, as described below.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Play Mode When switched to UCI mode, the iPod威 automatically starts Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the iPod威 and display data: • Use the TUNE control knob to select the next or previous track. • Turning it clockwise (forward) by one click, while playing a track, skips to the next track.
220 UNDERSTANDING YOUR INSTRUMENT PANEL • While a track is playing, press the INFO button to see the associated metadata (Artist, track title, album, etc.) for that track. Pressing the INFO button again jumps to the next screen of data for that track. Once you have seen all screens, the last INFO button press will take you back to the play mode screen on the radio. • Pressing the REPEAT button will change the iPod威 mode to repeat the current playing track.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 • During all List modes, the iPod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list just turn the wheel backwards (counter-clockwise) to get to the track faster. • In List mode, the radio PRESET Buttons are used as shortcuts to the following lists on the iPod威.
222 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • Leaving the iPod威 (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation, or damage the device. Follow the device manufacturer’s guidelines. • Placing items on the iPod威, or connections to the iPod威 in the vehicle, can cause damage to the device and/or to the connectors. WARNING! Do not plug in or remove the iPod威 while driving. Failure to following this warning could result in an accident.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.siriuscanada.ca for Canadian residents. Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen.
224 UNDERSTANDING YOUR INSTRUMENT PANEL bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows.
226 UNDERSTANDING YOUR INSTRUMENT PANEL • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 KICKER姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECTABLE SURROUND (DSS) – IF EQUIPPED any stereo audio source. A new feature of the Kicker威 audio system offers the ability to choose surround sound for any audio source. “Audio Surround” is optimized for front seat passengers for any audio source.
228 UNDERSTANDING YOUR INSTRUMENT PANEL When in “Audio Surround” mode, balance is set automatically. Fader control is available to add more surround audio if desired. The remote sound system controls are located on the surface of the steering wheel at the three and nine o’clock positions. REMOTE SOUND SYSTEM CONTROLS Vehicles equipped with steering wheel-mounted buttons are also equipped with the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING YOUR INSTRUMENT PANEL 229 If the Compass/Temp/Audio screen is already displayed when the AUDIO MODE button is pressed, then the mode will change (i.e., from AM to FM, to Media mode, etc., depending on which radio is in the vehicle). FUNCTION SELECT Button When the EVIC is in the Compass/Temp/ Audio screen, press the FUNCTION SELECT button to operate various radio, media, and Universal Customer Interface (UCI) functions (i.e.
230 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have copyright encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Blower Control Use this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (Off) position. There are four blower speeds. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
232 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control Use this control to choose from several patterns of air distribution. You can select either a primary mode as identified by the symbols on the control, or a blend of two of these modes. • Panel Air is directed through the outlets in the instrument panel and the center console. These outlets can be adjusted to direct airflow.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 • Mix Air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. • Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting.
234 UNDERSTANDING YOUR INSTRUMENT PANEL • The A/C will engage automatically to prevent fogging when the recirculation button is pressed. • The A/C can be deselected manually without disturbing the mode control selection. Air Conditioning Control Use this button to engage the Air Conditioning. A light will illuminate when the Air Conditioning System is engaged. NOTE: The air conditioning compressor will not engage until the engine has been running for a few seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 If Outside Ambient Temperature Is Less than 40°F Between 40°F and 80°F More than 80°F Mode Overrides To Temperature Overrides To Mix No Override Bi-Level Full Heat No Override Full Cool NOTE: • The feature can be disable by parking the vehicle with the blower control set to the “O” (or OFF) position. • For maximum performance, it is recommended that the vehicle is parked with the blower control set to the “High” (full clockwise) position.
236 UNDERSTANDING YOUR INSTRUMENT PANEL fresh air and high blower settings. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Floor, Mix, or Defrost mode. The air is directed at the area of the windows through which you view the outside mirrors. Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Control Setting Suggestions for Various Weather Conditions 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . 243 ▫ Manual Transmission ▫ Automatic Transmission ▫ Keyless Go . . . . . . . . . . . . . . . . 243 . . . . . . . . . . . . . . 245 . . . . . . . . . . . . . . . . . . . . . . . 246 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . 246 ▫ Extremely Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 ▫ If Engine Fails To Start ▫ After Starting . . . . . . . .
240 STARTING AND OPERATING ▫ 5-Speed Automatic Transmission (5.7L Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 䡵 AutoStick威 — If Equipped . . . . . . . . . . . . . . 269 ▫ AutoStick威 — 3.5L Engine . . . . . . . . . . . . . 269 ▫ AutoStick威 — 5.7L Engine . . . . . . . . . . . . . 270 䡵 Driving On Slippery Surfaces ▫ Acceleration ▫ Traction . . . . . . . . . . . . 271 . . . . . . . . . . . . . . . . . . . . . . . 271 . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 241 ▫ Synchronizing ESP . . . . . . . . . . . . . . . . . . 287 ▫ ESP/BAS Malfunction Indicator Light And ESP/TCS Indicator Light . . . . . . . . . . . . . . . 288 䡵 Tire Safety Information ▫ Tire Markings . . . . . . . . . . . . . . . . 289 . . . . . . . . . . . . . . . . . . . . . 289 ▫ Tire Loading And Tire Pressure 䡵 Tires — General Information ▫ Tire Pressure . . . . . . . . . . . . 296 . . . . . . . . . . . . . . . . . . . . . .
242 STARTING AND OPERATING ▫ Reformulated Gasoline . . . . . . . . . . . . . . . 317 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . 317 ▫ E-85 Usage In Non-Flex Fuel Vehicles ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . 318 ▫ Materials Added To Fuel ▫ Fuel System Cautions . . . . . . . . . . . . . . 319 . . . . . . . . . . . . . . . . 319 ▫ Carbon Monoxide Warnings 䡵 Adding Fuel . . . . . 317 . . . . . . . . . . . 320 . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 243 STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
244 STARTING AND OPERATING Normal Starting with Integrated Key — Manual Transmission Normal starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Press the clutch pedal fully to the floor, and turn the ignition switch to the START position and release when the engine starts. If the engine fails to start within 15 seconds, turn the ignition switch to the OFF position, wait 10 to 15 seconds, then repeat the normal starting procedure.
STARTING AND OPERATING 245 Automatic Transmission The shift lever must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting into any driving gear. CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
246 STARTING AND OPERATING Removing the Button Keyless Go This feature allows the driver to operate the ignition switch with the push of a button, as long as the ENGINE START/STOP button is installed and the Remote Keyless Entry transmitter is in the passenger compartment. Installing and Removing the ENGINE START/STOP Button Installing the Button 1. Remove the ignition key. 2. Insert the ENGINE START/STOP button into the ignition switch with the lettering facing up and readable. 3.
STARTING AND OPERATING 247 To start the engine, the transmission must be in PARK or NEUTRAL. Press and hold the brake pedal while pressing the ENGINE START/STOP button once. The system takes over and attempts to start the vehicle. If the vehicle fails to start, the starter will disengage automatically after 10 seconds. If you wish to stop the cranking of the engine prior to the engine starting, press the button again.
248 STARTING AND OPERATING NOTE: If the ignition switch is left in the ACC position the system will automatically time out after 60 minutes of inactivity and the ignition will switch to the OFF position. To Turn Off the Engine Using ENGINE START/STOP Button — Manual Transmission Only 1. With the vehicle stopped, place the shift lever in NEUTRAL, then press and release the ENGINE START/ STOP button. 2. The ignition switch will return to the OFF position. 3.
STARTING AND OPERATING 249 START. To change the ignition switch positions without starting the vehicle and use the accessories follow these steps.
250 STARTING AND OPERATING WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
STARTING AND OPERATING 251 and hold the clutch pedal, push the accelerator pedal all the way to the floor and hold it, then press and hold the ENGINE START/STOP button for no more than 15 seconds. Release the accelerator pedal and the clutch pedal, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure. Clearing A Flooded Engine (Using Fob With Integrated Key) If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded.
252 STARTING AND OPERATING WARNING! CAUTION! Remember to disconnect the cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. • Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Refer to “Electronic Brake Control System/Hill Start Assist” in this section.
STARTING AND OPERATING 253 spring helps you know which gear you are in when you are shifting. Be careful when shifting from first to second or downshifting from sixth to fifth. The spring will try to pull the shift lever toward third and fourth gear. Make sure you move the shift lever into second or fifth gear. If you let the shift lever move in the direction of the pulling, you may end shifting from first to fourth or from sixth to third gear.
254 STARTING AND OPERATING Recommended Shift Speeds To utilize your manual transmission efficiently for fuel economy, it should be upshifted as listed in recommended shift speed chart. MANUAL TRANSMISSION RECOMMENDED SHIFT SPEEDS Axle Ra1-4 4-5 tio mph 20 25 3.73 (km/h) (32) (40) mph 20 37 3.91 (km/h) (32) (59) 5-6 42 (67) 48 (77) Earlier upshifts during cruise conditions (relatively steady speeds) may result in increased fuel economy.
STARTING AND OPERATING 255 1–4 Skip Shift There are times when you must shift the transmission directly from first gear to fourth gear instead of from first gear to second gear. This is to help you get the best possible fuel economy from your vehicle. This occurs when the engine coolant (antifreeze) is higher than 106°F (41°C), vehicle speed is greater than 19 mph (30 km/h) but less than 21 mph (34 km/h), and the transmission is in first gear, and the accelerator is at 1/4 throttle or less.
256 STARTING AND OPERATING AUTOMATIC TRANSMISSION — IF EQUIPPED CAUTION! Damage to the automatic transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING 257 • Shift lever position • Accelerator position • Vehicle speed The gear shifting process is continuously adapted, dependent on the driving style, the driving situation, and the road characteristics. NOTE: • After selecting any driving position, wait a moment to allow the gear to engage fully before accelerating, especially when the engine is cold. • If there is a need to restart the engine, be sure to cycle the key to the LOCK position before restarting.
258 STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into PARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
STARTING AND OPERATING 259 pressing the override tab, move the shift lever out of the PARK position. When complete, return the override cover to its original position. Interlock Manual Override To activate the override, first insert the key into the ignition switch and turn it to the ACC or ON position. Then, press the pink-colored tab through the access port with a small flat-bladed screwdriver or alike.
260 STARTING AND OPERATING 4-Speed Automatic Transmission (3.5L Engine) NOTE: Under extreme cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only 2nd gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level. Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped.
STARTING AND OPERATING 261 When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. The following indicators should be used to ensure that you have engaged the shift lever in the PARK position: When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of park.
262 STARTING AND OPERATING NEUTRAL The engine may be started in this range. CAUTION! Coasting the vehicle or driving for any other reason with shift lever in NEUTRAL can result in transmission damage. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident.
STARTING AND OPERATING 263 “3” (Third) This range eliminates shifts into Overdrive. The transmission will operate normally in 1st, 2nd, and 3rd while in this range. The “3” position should also be used when descending steep grades to prevent brake system distress. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat buildup.
264 STARTING AND OPERATING NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant is warm (usually after 1–3 miles [1.6–4.8 km] of driving). Because engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is considered a normal condition. Pulling the shift lever into the “3” position will show that the transmission is able to shift into and out of Overdrive.
STARTING AND OPERATING 265 possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required. 5-Speed Automatic Transmission (5.7L Engine) Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when moving the shift lever between these gears.
266 STARTING AND OPERATING When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. The following indicators should be used to ensure that you have engaged the shift lever in the PARK position: When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK.
STARTING AND OPERATING 267 NEUTRAL In NEUTRAL, no power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage NEUTRAL position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads). The engine may be started in this range. Use this range for starting your vehicle if it is moving or being towed.
268 STARTING AND OPERATING under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing heavy trailers, use the AutoStick威 mode and select the “3” range. brought to a stop. After the vehicle has stopped, PARK, REVERSE, and NEUTRAL will continue to operate. Second gear will operate in the DRIVE position. The Malfunction Indicator Light (MIL) may be illuminated.
STARTING AND OPERATING 269 NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. Have the transmission checked at your authorized dealer as soon as possible. If the problem has been momentary, the transmission can be reset to regain all forward gears. AUTOSTICK姞 — IF EQUIPPED Autostick姞 — 3.
270 STARTING AND OPERATING Autostick姞 — 5.7L Engine Autostick威 is a driver-interactive transmission that offers manual gear shifting to provide you with more control of the vehicle. Autostick威 allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
STARTING AND OPERATING 271 • Starting out in second gear is helpful in snowy or icy conditions. • Avoid using speed control when Autostick威 is engaged. • The transmission will automatically shift up when maximum engine speed is reached while Autostick威 is engaged. • Transmission shifting will be more sharper when Autostick威 is engaged.
272 STARTING AND OPERATING 2. Slow down if the road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle.
STARTING AND OPERATING 273 CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water, and if there are any obstacles in the way, before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
274 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 275 WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used.
276 STARTING AND OPERATING PARKING BRAKE The parking brake should always be applied when the driver is not in the vehicle. The brake light in the instrument cluster will turn on when the parking brake is applied and the ignition switch is ON. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING 277 Automatic Transmission — If Equipped The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the parking brake, push the parking brake pedal down and then remove your foot from the pedal. To release the parking brake, push down on the parking brake pedal and then release. WARNING! Never use PARK position on an automatic transmission as a substitute for the parking brake.
278 STARTING AND OPERATING WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident.
STARTING AND OPERATING 279 When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self check cycle to ensure that the ABS system is working properly. This self check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). ABS is activated during braking under certain road or stopping conditions.
280 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 281 the conventional brake system will continue to operate normally if the Brake Warning Light is not on. If the ABS Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS Light does not come on when the ignition switch is turned to the ON position, have the bulb repaired as soon as possible. If both the Brake Warning Light and the ABS Light remain on, the ABS and EBD systems are not functioning.
282 STARTING AND OPERATING WARNING! The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ABS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 283 must apply continuous brake pedal pressure during the stopping sequence. Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated. WARNING! The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
284 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backing uphill is in REVERSE gear). WARNING! There may be situations on minor hills (i.e., less than 8%), with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may occur. This could cause a collision with another vehicle or object. Always remember the driver is responsible for braking the vehicle.
STARTING AND OPERATING 285 8. Rotate the steering wheel back to center and then an additional half-turn to the right. 9. Turn the ignition switch to the OFF position and then back to the ON position. If the sequence was completed properly, the ESP/TCS Indicator Light will blink several times to confirm HSA is disabled. 10. Repeat these steps if you want to return this feature to it’s previous setting.
286 STARTING AND OPERATING accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. WARNING! The ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
STARTING AND OPERATING 287 To turn the ESP ON again, momentarily depress the ESP OFF switch and the ESP/TCS Indicator Light will turn off. ESP OFF Switch NOTE: To improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by momentarily depressing the ESP OFF switch. Once the situation requiring “Partial Off” mode is overcome, turn the ESP ON again by momentarily depressing the ESP OFF switch.
288 STARTING AND OPERATING ESP/BAS Malfunction Indicator Light and ESP/TCS Indicator Light The Malfunction Indicator Light for the ESP is combined with the BAS indicator. The yellow ESP/BAS Malfunction Indicator Light and the yellow ESP/TCS Indicator Light in the instrument cluster both come on when the ignition switch is turned to the ON position. They should go out with the engine running.
STARTING AND OPERATING 289 TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
290 STARTING AND OPERATING CAUTION! Do not use two different size tires on the rear wheels, as this can result in rear axle damage. Tire Sizing Chart TIRE SIZING TERMS Size Designation: P = Passenger Car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger Car tire based on European design standards LT = Light Truck tire based on U.S.
STARTING AND OPERATING 291 TIRE SIZING TERMS R = Construction code — ⬙R⬙ means radial construction —⬙D⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achi
292 STARTING AND OPERATING TIRE SIZING TERMS Light Load = Light load tire C, D, E = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load — Maximum load indicates the maximum load this tire is designed to carry Maximum Pressure — Maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side.
STARTING AND OPERATING 293 TIRE IDENTIFICATION NUMBER EXAMPLE: DOT MA L9 ABCD 0301 MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits) 03 = Number representing the week in which the tire was manufactured (two digits) —03 means the 3rd week.
294 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING 295 axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on the Tire and Loading Information placard.
296 STARTING AND OPERATING NOTE: • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs (392 kg). WARNING! Overloading of your tires is dangerous.
STARTING AND OPERATING 297 5
298 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures can cause steering problems. You could lose control of your vehicle. • Over-inflated or under-inflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control. • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure.
STARTING AND OPERATING 299 once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under-inflated. CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
300 STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
STARTING AND OPERATING 301 vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life.
302 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.
STARTING AND OPERATING 303 Many states have laws requiring tire replacement at this point. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death.
304 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 305 The 245/45 R20 size tires do not provide adequate clearance for tire chains. NOTE: Do not use tire chains on a compact spare tire. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage.
306 STARTING AND OPERATING pavement. Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacturer suggest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains. SNOW TIRES Some areas of the country require the use of snow tires during the winter.
STARTING AND OPERATING 307 TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. Follow the Maintenance Schedule in Section 8 for the recommended tire rotation frequency. Remember, more frequent rotation is permissible if desired. Also, correct for anything causing rapid or unusual wear prior to performing the tire rotation.
308 STARTING AND OPERATING The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure.
STARTING AND OPERATING 309 CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
310 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in the tire. Base System The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module.
STARTING AND OPERATING 311 off when the fault condition no longer exists. A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5.
312 STARTING AND OPERATING Premium System — If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module. NOTE: It is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure.
STARTING AND OPERATING 313 turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS Warning If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime.
314 STARTING AND OPERATING 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors.
STARTING AND OPERATING 315 limit, upon the next ignition key cycle, the TPM Telltale Light will remain ON and a chime will sound. In addition, the graphic in the EVIC will still display a flashing pressure value. 3. After driving the vehicle for up to 20 minutes above 15 mph (25 km/h), the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid.
316 STARTING AND OPERATING United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 Canada . . . . . . . . . . . . . . . . . . . . . . . . 2671-S120123 FUEL REQUIREMENTS 3.5L and 5.7L Engines (with Automatic Transmission) The 3.5L and 5.7L engines (with automatic transmission) are designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high-quality unleaded gasoline having an octane range of 87 to 89.
STARTING AND OPERATING 317 Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” Reformulated gasolines contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components.
318 STARTING AND OPERATING • operate in a lean mode • OBD II “Malfunction Indicator Light” on • poor engine performance • poor cold start and cold drivability • increased risk for fuel system component corrosion To fix a Non-FFV vehicle inadvertently fueled once with E-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory More extensive repairs will be required for prol
STARTING AND OPERATING 319 Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
320 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 321 5 Fuel Filler Cap Fuel Filler Cap (If Equipped) NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door.
322 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunction Indicator Light (MIL) to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING 323 Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap” message will display in the Electronic Vehicle Information Center (EVIC). If this occurs, tighten the fuel filler cap properly and press the TRIP ODOMETER button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started.
324 STARTING AND OPERATING The bar code allows a computer scanner to read the VIN. Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
STARTING AND OPERATING 325 Figure out the weight on the front and rear of the vehicle separately. It is important that you distribute the load evenly over the front and rear axles. NOTE: Refer to the “Vehicle Certification Label” affixed to the rear of the driver’s door for your vehicle’s GVWR and GAWRs. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR.
326 STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo, and tongue weight. The total load must be limited so that you do not exceed the GVWR. Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables, and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition.
STARTING AND OPERATING 327 Frontal Area The frontal area is the maximum height and maximum width of the front of a trailer. Trailer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
328 STARTING AND OPERATING WARNING! • An improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in an accident. • Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recreational vehicle dealer for additional information.
STARTING AND OPERATING 329 Engine/Transmission Frontal Area 3.5L Automatic 12 sq ft (1.11 sq m) 5.7L Automatic 12 sq ft (1.11 sq m) Refer to local laws for maximum trailer towing speeds Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
330 STARTING AND OPERATING Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
STARTING AND OPERATING 331 WARNING! (Continued) Make certain that the load is secured in the trailer and it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
332 STARTING AND OPERATING Towing Requirements — Tires Towing Requirements — Trailer Brakes − Do not attempt to tow a trailer while using a compact spare tire. − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 333 CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes, and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
334 STARTING AND OPERATING 4-Pin Connector 1 — Female Pins 2 — Male Pin 3 — Ground 4 — Park 5 — Left Stop/Turn 6 — Right Stop/Turn 7-Pin Connector 1 2 3 4 — — — — Battery Backup Lamps Right Stop/Turn Electric Brakes 5 — Ground 6 — Left Stop/Turn 7 — Running Lamps
STARTING AND OPERATING 335 Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Towing Tips — Automatic Transmission The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected.
336 STARTING AND OPERATING − Extended driving at high RPM should be avoided to prevent excess heat generation. A reduction in vehicle speed may be required to avoid extended driving at high RPM. Return to a higher gear range or vehicle speed when road conditions and RPM level allows. − Highway Driving Reduce speed. Towing Tips — Cooling System To reduce potential for engine and transmission overheating, take the following actions: RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . 338 䡵 Jump-Starting 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . 338 䡵 Freeing A Stuck Vehicle 䡵 TIREFIT Tire Repair — If Equipped 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . 345 ▫ Jack Location/Spare Tire Stowage ▫ Preparations For Jacking . . . . . . . 345 . . . . . . . . . . . . . . 347 ▫ Jacking And Changing a Tire ▫ Compact Spare Tire . . . . . . . 339 . . . . . . . . . . .
338 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located in the switch bank near the bottom center of the instrument panel. Press the switch to turn on the Hazard Warning flashers. When the Hazard Warning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off flashers.
WHAT TO DO IN EMERGENCIES 339 the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (116 °C) or greater pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range 200– 230°F (93–110°C).
340 WHAT TO DO IN EMERGENCIES The TIREFIT system is located under an access panel in the trunk. TIREFIT Kit 1. Air pump hose TIREFIT Location 2. Power plug and cable 3. AIR PUMP switch 4.
WHAT TO DO IN EMERGENCIES 341 5. TIREFIT sealant bottle WARNING! (Continued) 6. TIREFIT sealant hose WARNING! • Do not attempt to repair a tire on the side of the vehicle close to traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or repairing a tire. • Cuts or punctures larger than approximately 0.16 in (4 mm), tire damage caused by driving with extremely low tire pressure or on a flat tire, or a damaged wheel can pose a hazard while driving.
342 WHAT TO DO IN EMERGENCIES Sealing Tire with TIREFIT 1. Turn on the Hazard Warning Flashers. 2. Move the shift lever into PARK (automatic transmission) or in gear (manual transmission), turn OFF the engine and set the parking brake. 3. Remove the TIREFIT kit from the trunk. 4. Pull the power plug 2 and the TIREFIT sealant hose 6 out from the TIREFIT kit. 5. Unscrew the valve cap from the valve on the deflated tire. 6.
WHAT TO DO IN EMERGENCIES 343 13. Turn on the Hazard Warning Flashers. 14. Move the shift lever into PARK (automatic transmission) or in gear (manual transmission), turn OFF the engine and set the parking brake. 15. Disconnect the air pump hose 1 from the underside of the sealant bottle 5 by flipping the hose valve open. 16. Connect the air pump hose valve to the tire valve and flip the hose valve closed. 17.
344 WHAT TO DO IN EMERGENCIES 24. Connect the air pump hose valve to the tire valve and flip the hose valve closed. 28. Disconnect the TIREFIT system from the tire and reinstall the valve cap. 25. Check the pressure in the tire by reading the pressure gauge 4. If the pressure is 19 psi (1.3 bar) or greater, proceed to the following step. NOTE: If the pressure is less than 19 psi (1.3 bar), the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. 29.
WHAT TO DO IN EMERGENCIES 345 • If TIREFIT is liquid, clean water and a damp cloth will remove the material from the vehicle or tire and wheel components. Once TIREFIT sealing material has dried, it can easily be peeled off and properly discarded. • Do not exceed 55 mph (90 km/h) until the tire has been inspected. JACKING AND TIRE CHANGING WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic.
346 WHAT TO DO IN EMERGENCIES NOTE: The spare tire must be removed in order to access the jack. 1. Open the trunk. 2. Lift the access cover using the pull strap. Spare Tire Fastener 4. Remove the spare tire. 5. Remove the fastener securing the jack. Opening The Access Panel 3. Remove the fastener securing the spare tire.
WHAT TO DO IN EMERGENCIES 347 Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. 2. Set the parking brake and place the shift lever into PARK (automatic transmission) or REVERSE (manual transmission). 3. Turn OFF the ignition. 4. Turn on the Hazard Warning flashers. Jack Fastener WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
348 WHAT TO DO IN EMERGENCIES NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking and Changing a Tire WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised.
WHAT TO DO IN EMERGENCIES 349 Jack Warning Label 1. Remove the spare tire, jack, and lug wrench. 2. If equipped with steel wheels, do not remove the wheel cover at this time. If equipped with aluminum wheels where the center cap covers the lug nuts, use the lug wrench to pry the center cap off carefully before raising the vehicle. 6 Center Cap Removal WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with the metal edges and retention teeth.
350 WHAT TO DO IN EMERGENCIES 3. Before raising the vehicle, use the lug wrench to loosen, but not remove, the lug nuts on the wheel with the flat tire. Turn the lug nuts counterclockwise one turn while the wheel is still on the ground. 4. Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange. Jack Engagement Locations Lug Nut Removal/Installation 1 — Tighten 2 — Loosen 5.
WHAT TO DO IN EMERGENCIES 351 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts, wheel cover (if equipped), and tire. Remove the cover by hand. Do not pry it off. 7. Mount the spare tire. NOTE: For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare.
352 WHAT TO DO IN EMERGENCIES WARNING! WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. The limited-use spare tires are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h).
WHAT TO DO IN EMERGENCIES 353 1. Mount the road tire on the axle. For vehicles equipped with wheel covers, perform Steps 2 and 3. For vehicles equipped with center caps, proceed to Step 4. 2. Install two lug nuts on the mounting studs, which are on each side of the stud that is in alignment with the valve stem. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
354 WHAT TO DO IN EMERGENCIES snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle is lowered to the ground. 5. Lower the vehicle to the ground by turning the jack handle counterclockwise. 6. Finish tightening the lug nuts.
WHAT TO DO IN EMERGENCIES 355 JUMP-STARTING WARNING! (Continued) WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
356 WHAT TO DO IN EMERGENCIES NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump-starting. 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach, but do not allow the vehicles to touch one another.
WHAT TO DO IN EMERGENCIES 357 NOTE: Refer to ⬙Synchronizing ESP⬙ under ⬙Electronic Stability Program⬙ in Section 5 if the ESP/BAS light (in the instrument cluster) remains on continuously after starting the engine of the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Jump-Starting 7. Start the engine in the vehicle that has the booster battery. Let the engine idle a few minutes.
358 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • During cold weather when temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode. The battery temperature must be brought above the freezing point before attempting jump-start. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved by a rocking motion.
WHAT TO DO IN EMERGENCIES 359 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed. TOWING A DISABLED VEHICLE Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position.
360 WHAT TO DO IN EMERGENCIES If the transmission is not operative or if the vehicle is to be towed more than 30 miles (48 km), the vehicle must be transported using a flatbed truck. CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • If the transmission is not operative or if the vehicle is to be towed more than 30 miles (48 km), then the only approved method of towing is with a flatbed truck.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . 363 ▫ Engine Oil 䡵 Engine Compartment — 5.7L . . . . . . . . . . . . 364 ▫ Engine Oil Filter 䡵 Onboard Diagnostic System — OBD II ▫ Loose Fuel Filler Cap . . . . . 365 . . . . . . . . . . . . . . . . 365 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 䡵 Replacement Parts 䡵 Dealer Service . . . . . . . . . . . . . . . . . . . . 367 . . . . . . . . . . .
362 MAINTAINING YOUR VEHICLE ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . 385 ▫ Clutch Hydraulic System — Manual Transmission (If Equipped) . . . . . . . . . . . . . 387 ▫ Manual Transmission — If Equipped ▫ Automatic Transmission — If Equipped ▫ Rear Axle . . . . . 387 . . . 387 . . . . . . . . . . . . . . . . . . . . . . . . 389 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 389 䡵 Fuses . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 363 ENGINE COMPARTMENT — 3.
364 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.
MAINTAINING YOUR VEHICLE 365 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
366 MAINTAINING YOUR VEHICLE Trip Odometer button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. serviced, recently had a dead battery, or a battery replacement. If the OBD II system should be determined not ready for the I/M test, the vehicle may fail the test. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL.
MAINTAINING YOUR VEHICLE 367 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition key or start the engine. This means that the vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition key or start the engine.
368 MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE 369 The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding 1.0 qt (1.
370 MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever occurs first. Engine Oil Viscosity (SAE Grade) — 3.5L Engine SAE 10W-30 engine oil is preferred for for all operating temperatures.
MAINTAINING YOUR VEHICLE 371 The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in this section. Lubricants that do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used.
372 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance.
MAINTAINING YOUR VEHICLE 373 WARNING! Battery Location • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
374 MAINTAINING YOUR VEHICLE WARNING! (Continued) • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE 375 WARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product.
376 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield.
MAINTAINING YOUR VEHICLE 377 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
378 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE 379 To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle (automatic transmission only). • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idling or malfunctioning operating conditions.
380 MAINTAINING YOUR VEHICLE system should be drained, flushed, and refilled with fresh coolant. Check the front of the radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks.
MAINTAINING YOUR VEHICLE 381 CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol-based engine coolant (antifreeze) products.
382 MAINTAINING YOUR VEHICLE When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated.
MAINTAINING YOUR VEHICLE 383 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
384 MAINTAINING YOUR VEHICLE of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE 385 • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions.
386 MAINTAINING YOUR VEHICLE Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
MAINTAINING YOUR VEHICLE 387 Clutch Hydraulic System — Manual Transmission (If Equipped) The clutch hydraulic system is fed by a segregated volume of fluid within the brake system master cylinder reservoir. In the event of leakage or wear, use only the manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
388 MAINTAINING YOUR VEHICLE If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level. CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes.
MAINTAINING YOUR VEHICLE 389 Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only manufacturer’s recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
390 MAINTAINING YOUR VEHICLE parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.
MAINTAINING YOUR VEHICLE 391 CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open.
392 MAINTAINING YOUR VEHICLE heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner (05066247AB) or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish.
MAINTAINING YOUR VEHICLE 393 Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. quarter window equipped with the radio antenna. Do not use scrapers or other sharp instrument that may scratch the elements. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using.
394 MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use MOPAR威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. FUSES Integrated Power Module (IPM) The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays.
MAINTAINING YOUR VEHICLE 395 CAUTION! • When installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
396 MAINTAINING YOUR VEHICLE Cavity 8 9 10 11 12 13 14 Cartridge Fuse — MiniFuse Description 25 Amp Starter Neutral — — — 30 Amp — Windshield Wiper Pink 30 Amp — Anti-Lock Brake System Pink (ABS) Valves 40 Amp — Radiator Fan Lo/High Green 50 Amp — Anti-Lock Brake System Red (ABS) Pump Motor — — — Cavity 15 16 17 18 19 20 21 22 Cartridge Fuse 50 Amp Red — — — — — — — MiniFuse Description — Radiator Fan — — — — — — — — — — — — — —
MAINTAINING YOUR VEHICLE 397 Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.
398 MAINTAINING YOUR VEHICLE CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE 399 Cavity 8 Cartridge Fuse — 9 — 10 11 * 12 * 13 * 14 — — — — — 15 16 — — MiniFuse Description 15 Amp Diagnostic Link ConnecBlue tor (DLC)/Wireless Control Module (WCM)/ Wireless Ignition Node (WIN) 20 Amp Power Outlet Yellow — — — — — — — — 10 Amp AC Heater Control/ Red Cluster/Security Module - if equipped — — — — Cavity 17 Cartridge Fuse — 18 — 19 — 20 21 22 23 24 25 26 27 — — — — — — — — MiniFuse Description 20 Amp Yellow 20 Amp Yellow 10 Amp Red — — — —
400 MAINTAINING YOUR VEHICLE Cavity 28 Cartridge Fuse — 29 — 30 — 31 32 33 34 — — — — MiniFuse Description 10 Amp Ignition Run Red 5 Amp Cluster/Electronic StaOrange bility Program (ESP)/ Powertrain Control Module (PCM)/STOP LIGHT Switch 10 Amp Door Modules/Power Red Mirrors/Steering Control Module (SCM) — — — — — — — — Cavity 35 Cartridge Fuse — 36 — 37 — 38 — 39 — 40 — MiniFuse 5 Amp Orange Description Antenna Module - if equipped/Power Mirrors 25 Amp Hands-Free Phone - if Clea
MAINTAINING YOUR VEHICLE 401 Cavity 41 42 43 44 Cartridge Fuse — MiniFuse Description 10 Amp AC Heater Control/ Red Headlights/Tire Pressure Monitoring - if equipped 30 Amp — Front Blower Motor Pink 30 Amp — Rear Window Defroster Pink 20 Amp — Amplifier - if equipped/ Blue Sunroof - if equipped * Cavities 11, 12, and 13 contain self-resetting fuses (circuit breakers) that are only serviceable by an authorized dealer.
402 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Rear Courtesy/Reading Lights. . . . . . . . . . . . . . W5W Rear Compartment (Trunk) Light . . . . . . . . . . . . . 562 Overhead Console Reading Lights. . . . . . . . . . . . . 578 Visor Vanity Lights . . . . . . . . . . . . . . . . . . . . . A6220 Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194 Door Courtesy . . . . . . . . . . . . . . . . . . . . . . . . . . 562 Shift Indicator Light . . . . . .
MAINTAINING YOUR VEHICLE 403 BULB REPLACEMENT Low Beam Headlight, High Beam Headlight, Park/Turn Light — Models with Halogen Headlights — If Equipped See your authorized dealer for bulb replacement. Low Beam Headlight, High Beam Headlight, and Park/Turn Light — Models with High Intensity Discharge (HID) Headlights — If Equipped HID Headlights The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the HEADLIGHT switch off and the key removed.
404 MAINTAINING YOUR VEHICLE NOTE: • If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to scratch the paint. 2. Rotate the bulb’s socket counterclockwise, and remove the bulb and socket assembly from the housing. 3. Pull the bulb out of the socket and insert the replacement bulb. 4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Reinstall the front/rear side marker. Tail/Turn/Stop Light 1.
MAINTAINING YOUR VEHICLE 405 3. Remove the fasteners from the back of the tail light assembly. 5. Remove the remaining fasteners from the back of the tail light assembly. 6. Pull the tail light assembly clear from the vehicle to access the bulbs. 7 4. Pull back the trunk liner.
406 MAINTAINING YOUR VEHICLE 7. Push the electrical connector locking tab to the side. 8. Disconnect the electrical connector. 9. Turn the appropriate bulb and socket assembly counterclockwise to remove it from the tail light assembly. 10. Disconnect the bulb from the socket assembly and install the replacement bulb. 11. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise. 12. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner.
MAINTAINING YOUR VEHICLE 407 Center Tail/Backup Light See your authorized dealer for bulb replacement. Center High-Mounted Stop Light (CHMSL) The CHMSL uses LED lights that are not serviceable separately. The CHMSL must be replaced as an assembly, see your authorized dealer. License Light 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly. 3. Disconnect the bulb from the socket assembly and install the replacement bulb. 1 — License Light Bulb 2 — Socket 4.
408 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) 3.5 Liter Engine 5.7 Liter Engine Engine Oil with Filter 3.5 Liter Engine (SAE 10W-30, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) Cooling System * 3.5 Liter Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent 5.7 Liter Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent * Includes heater and coolant recovery bottle filled to MAX level. U.S.
MAINTAINING YOUR VEHICLE 409 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (3.5L Engine) Engine Oil (5.7L Engine) Spark Plugs (3.5L Engine) Spark Plugs (5.7L Engine) Oil Filter (3.5L and 5.7L Engines) Fuel Selection (3.5L and 5.7L Engine — Automatic Transmission) Fuel Selection (5.
410 MAINTAINING YOUR VEHICLE Chassis Component Manual Transmission Automatic Transmission Brake Master Cylinder Power Steering Reservoir Rear Axle (3.5L Engine) Rear Axle (5.7L Engine) Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 DOT 3, SAE J1703 or equivalent should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance 䡵 Maintenance Schedule . . . . . 412 . . . . . . . . . . . . . . . . . 412 ▫ Required Maintenance Intervals . . . . . . . . .
M A I N T E N A N C E 412 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emission Control System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 413 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or six months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 414 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery, and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, power steering, and transmission, and add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.
MAINTENANCE SCHEDULES 415 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
M 416 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the rear axle fluid. 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 417 M 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (5.7L Engine). ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 418 MAINTENANCE SCHEDULES A I N 42,000 Miles (70,000 km) or T 42 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 419 M 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (5.7L Engine). Replace the air conditioning filter (if equipped) Inspect the brake linings; replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M 420 MAINTENANCE SCHEDULES A I N 66,000 Miles (110,000 km) or T 66 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ If using your vehicle for any of the S C H E D U L E S 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires.
MAINTENANCE SCHEDULES 421 M 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 422 MAINTENANCE SCHEDULES A I N 96,000 Miles (160,000 km) or T 96 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Replace the air conditioning filter (if S C H E D U L E S equipped) ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals; replace if necessary. ❏ Change the manual transmission fluid (if equipped).
MAINTENANCE SCHEDULES 423 M 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter.
M 424 MAINTENANCE SCHEDULES A I N 126,000 Miles (210,000 km) or T 126 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ If using your vehicle for any of the S C H E D U L E S following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the rear axle fluid.
MAINTENANCE SCHEDULES 425 M 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the air conditioning filter (if equipped) Inspect the brake linings; replace if necessary. Inspect the CV joints. Inspect exhaust system. Inspect the rear axle fluid. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.
M A I N T E N A N C E S C H E D U L E S 8 426 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 ▫ Prepare For The Appointment ▫ Prepare A List . . . . . . . . . . 429 . . . . . . . . . . . . . . . . . . . . . 429 ▫ Be Reasonable With Requests 䡵 If You Need Assistance . . . . . . . . . . . 429 . . . . . . . . . . . . . . . . 429 ▫ Chrysler LLC Customer Center . . . . . . . . . 430 ▫ Chrysler Canada Inc.
428 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . 433 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 434 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . 435 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . 435 ▫ Temperature Grades . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 429 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
430 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE 431 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
432 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE 433 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
434 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE 435 Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
436 IF YOU NEED CONSUMER ASSISTANCE WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
438 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . 276,278 ABS (Anti-Lock Brake System) . . . . . . . . . . . . 278,281 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 381 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 376 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 319 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 372 Air Conditioner Maintenance . . . . . . . . . . . .
INDEX 439 Automatic Door Locks . . . . . . . . . . . . . . . . . . . 30,31 Automatic Headlights . . . . . . . . . . . . . . . . . . . . 121 Automatic Oil Change Indicator . . . . . . . . . . . . . 163 Automatic Transaxle Special Additives . . . . . . . . . . . . . . . . . . . . . . 389 Automatic Transmission . . . . . . . . . . . 260,265,387,388 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . 388,410 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269 Fluid and Filter Changes . .
440 INDEX Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 Warning Light . . . . . . . . . . . . . . . . . . . . . 164,278 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278,385 Brake/Transmission Interlock . . . . . . . . . . . . . . . 258 Break-In Recommendations, New Vehicle . . . . . . . . 67 Brightness, Interior Lights . . . . . . . . . . . . . . . . . . 125 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 402,403 Bulbs, Light . . . . . . . . . . . . .
INDEX 441 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 300 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Compass Calibration . . . . . . . . . . . . . . . . . . . . . 176 Compass Variance . . . . . . . . . . . . . . . . . . . . . . . 177 Computer, Trip/Travel . . . . . . . . . . . . . . . . . . . . 173 Connector UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Universal Consumer Interface (UCI) . . . . . . . . . 217 Console . . . . . . . .
442 INDEX Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . 127 Diagnostic System, Onboard . . . . . . . . . . . . . . . . 365 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 124 Dipsticks Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . 368,369 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 275 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 359 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . 383 Engine Oil . . . . . . . . .
INDEX 443 Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . 251 Break-In Recommendations . . . . . . . . . . . . . . . . 67 Checking Oil Level . . . . . . . . . . . . . . . . . . 368,369 Compartment . . . . . . . . . . . . . . . . . . . . . . 363,364 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . 379,409 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 68,320 Fails to Start . . . . . . . . . . . . . . . . . .
444 INDEX Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 338 Turn Signal . . . . . . . . . . . . . . . . . . . . . . 70,124,160 Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Flat Tire Changing . . . . . . . . . . . . . . . . . . . . . . . 345 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 249 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 410 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 445 Garage Door Opener (HomeLink威) . . . . . . . . . . . 134 Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . . . . 320,365 Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . 317 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 316 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 317 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . 159 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Odometer . . . . . . . . . . . . . .
446 INDEX Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heater, Engine Block . . . . . . . . . . . . . . . . . . High Beam/Low Beam Select (Dimmer) Switch Hill Start Assist . . . . . . . . . . . . . . . . . . . . . . Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . HomeLink威 (Garage Door Opener) Transmitter Hood Release . . . . . . . . . . . . . . . . . . . . . . . ... ... .. ... 230 251 124 283 . . . .
INDEX 447 Kicker Sound System . . . . . . . . . . . . . . . . . . . . . 227 Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Lane Change and Turn Signals . . . . . . . . . . . . . . 124 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 37 LATCH (Lower Anchors and Tether for CHildren) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61,63 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Hood . . . . . . . . . . . . . . . . . . . . . . .
448 INDEX High Beam/Low Beam Select . . . . . . . . . . . . . 124 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . 19 Instrument Cluster . . . . . . . . . . . . . . . . . . 120,158 Intensity Control . . . . . . . . . . . . . . . . . . . . . . 125 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . 125,133 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407 Lights On Reminder . . . . . . . . . . . . . . . . . . . . 123 Low Fuel . . . . . . . . . . . . . . . . . . .
INDEX 449 Maintenance Free Battery . . . . . . . . . . . . . . . . . . 372 Maintenance, General . . . . . . . . . . . . . . . . . . . . . 368 Maintenance Procedures . . . . . . . . . . . . . . . . . . . 368 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 412 Maintenance, Sunroof . . . . . . . . . . . . . . . . . . . . . 143 Malfunction Indicator Light (Check Engine) . . 168,366 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 433 Manual Transmission . . . . . . . . . . . . . .
450 INDEX Checking . . . . . . . . . . . . . . . . . . . . . . . . . 368,369 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . 368,369 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371,409 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . 371 Identification Logo . . . . . . . . . . . . . . . . . . . . . 370 Materials Added to . . . . . . . . . . . . . . . . . . . . . 371 Recommendation . . . . . .
INDEX 451 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . 274,275 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 410 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 45 Preparation for Jacking . . . . . . . . . . . . . . . . . . . .
452 INDEX Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 303 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 432 Resetting Oil Change Indicator . . . . . . . . . . . . . . 163 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 115 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . 58 Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . 36 Rocking Vehicle When Stuck . . . . . . . . . . . . . . . . 358 Rotation, Tires . . . . . . . .
INDEX 453 Rear Folding . . . . . . . . . . . . . . . . . . . . . . . . . 117 Seatback Release . . . . . . . . . . . . . . . . . . . . . . . 117 Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . . 18 Selection of Coolant (Antifreeze) . . . . . . . . . . 380,409 Selection of Oil . . . . . . . . . . . . . . . . . . . . . . . . . 370 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . 15 Sentry Key Programming . . . . .
454 INDEX Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . . 249 Emergency (Jump Starting) . . . . . . . . . . . . . . . 355 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 249 Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Starting and Operating . . . . . . . . . . . . . . . . . . . . 243 Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 243 Steering Column Controls . . . . . . . . . . . . . . . . . . . . . . 123 Column Lock . . . . . . . . .
INDEX 455 TIREFIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70,296,434 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . 303 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 Changing . . . . . . . . . . . . . . . . . . . . . . . . . 345,348 Compact Spare . . . . . . . . . . . . . . . . . . . . . . . . 300 Flat Changing . .
456 INDEX Towing Vehicle Behind a Motor Home . . . . . . . . . 336 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . 282 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 325 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 336 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328 Minimum Requirements . . . . . . . . . . . . . . . . . 330 Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 Trailer and Tongue Weight . . . . .
INDEX 457 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . 316 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . 42 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 177 Vehicle Certification Label . . . . . . . . . . . . . . . . . 323 Vehicle Identification Number (VIN) . . . . . . . . . . . . 6 Vehicle Loading . . . . . . . . . . . . . . . . . . . 294,323,325 Vehicle Modifications/Alterations .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
CHA LLE NG ER 2009 CHALLENGER 2009 OWNER’S MANUAL Chrysler LLC 81-226-0916 147914 Dodge LC22 Challenger.indd 1 Second Edition Printed in U.S.A.
