R IBE C AL 2009 OWNER’S MANUAL
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 ..............
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ To Set The Security Alarm . . . . . . . . . . . . . . . 19 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 12 ▫ To Disarm The System . . . . . . . . . . . . . . . . . 19 ▫ Locking Doors With The Key . . . . . . . . . . . . . 15 ▫ Vehicle Security Alarm Manual Override . . . . . 19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Sound Horn With Remote Key Lock . . . . . . . . 22 ▫ Auto Down . . . . . . . . . . . . . . . . . . . . . . . . . 33 ▫ Flash Lights With Remote Key Lock/Unlock . . 23 ▫ Window Lockout Switch . . . . . . . . . . . . . . . . 34 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 䡵 Liftgate ▫ Programming Additional RKE Transmitters . . . 25 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 36 ▫ General Information . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . 62 䡵 Engine Break-In Recommendations . . . . . . . . . . 70 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 ▫ Transporting Passengers . . . . . . . . . . . . . . . . 71 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 72 11 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic Transmission — If Equipped 1. Place the shift lever in PARK. 2. Turn the ignition switch to the ACC (Accessory) position. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. Manual Transmission 1. Turn the ignition switch to the ACC (Accessory) position. 2. Push the key and cylinder inward and rotate the key to the LOCK position. 3. Remove the key from the ignition switch lock cylinder.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locking Doors With The Key You can insert the key with either side up. To lock the door, turn the key to the right. To unlock the door, turn the key to the left. Refer to “Body Lubrication” under “Maintenance Procedures” in Section 7. 15 is automatic, regardless of whether the vehicle is locked or unlocked.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE someone used an invalid key to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds. starting the vehicle. Cell phones, pagers, or other Radio Frequency (RF) electronics will not cause interference with this system. If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by following the customer key programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The new Sentry Key威 is programmed. The Remote Keyless Entry (RKE) transmitter will also be programmed during this procedure. Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key威, contact your authorized dealer for details. NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Set The Security Alarm 1. Remove the key from the ignition switch and get out of the vehicle. 2. Lock the door using either the power door LOCK switch or the Remote Keyless Entry (RKE) transmitter and close all doors. 3. The Vehicle Security Light in the instrument cluster will flash rapidly for approximately 16 seconds. This shows that the Vehicle Security Alarm is arming.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY — IF EQUIPPED This system allows you to lock or unlock the doors and liftgate or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a handheld Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system. Three Button RKE Transmitter NOTE: The line of transmission must not be blocked with metal objects.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors And Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm. Illuminated Approach — If Equipped This feature activates the headlights for up to 90 seconds when the doors are unlocked with the RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the following steps: 1. Press the LOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button. 2. Release both buttons at the same time. 3. Test the feature while outside of the vehicle by pressing the LOCK button on the RKE transmitter with the ignition switch in the LOCK position and the key removed. 4.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the following steps: 1. Press and hold the UNLOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK button. 2. Release both buttons at the same time. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Programming Additional RKE Transmitters Refer to Sentry Key威 “Customer Key Programming.” If your RKE transmitter fails to operate from a normal distance, check for these two conditions: If you do not have a programmed RKE transmitter, contact your authorized dealer for details. 1. Weak batteries in the RKE transmitter. The expected life of batteries is five years.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. If the RKE transmitter is equipped with a screw, remove the screw. With the RKE transmitter buttons facing down, use a flat blade to pry the two halves of the RKE transmitter apart. Make sure not to damage the elastomer seal during removal. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! (Continued) • When leaving the vehicle, always remove the key from the ignition lock and lock your vehicle. Do not leave unattended children in the vehicle or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To prevent from locking the key in the vehicle, the power door lock switch will not operate when the key is in the ignition and either front door is open. A chime will sound as a reminder to remove the key. Automatic Door Locks — If Equipped The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The Auto Lock feature is enabled. 2. The transmission is in gear. 3. All doors are closed. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks Programming The Automatic Door Locks feature can be enabled or disabled as follows: • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC) — If Equipped” in Section 4. • For vehicles not equipped with the EVIC, perform the following procedure: 1. Close all doors and place the key in the ignition switch. 2.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The transmission is in NEUTRAL or PARK. 4. The driver’s door is opened. 3. Within 30 seconds, depress the power door UNLOCK switch to unlock the doors. 5. The doors were not previously unlocked. 4. A single chime will indicate the completion of the programming. Automatic Unlock Doors on Exit Programming The Automatic Unlock Doors On Exit feature can be enabled or disabled as follows: 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Child-Protection Door Lock System (Rear Doors) — If Equipped Insert the tip of the ignition key into the lock and rotate to the LOCK or UNLOCK position. 2 Child-Protection Door Lock Function WARNING! Child-Protection Door Lock Location Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down the window and open the door with the outside door handle. POWER WINDOWS — IF EQUIPPED Power Window Switches Power Window Switch Location The window controls on the driver’s door trim panel control all the door windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate when the ignition switch is in the ON or ACC position. NOTE: • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCKOUT switch. To enable the window controls, press the window LOCKOUT switch a second time. LIFTGATE NOTE: The key that is used to start your vehicle is also used to lock or unlock the doors and open the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • Although the liftgate has no inside release mechanism, the liftgate trim panel includes an opening with a snap-in cap that provides access to release the latch in the event of an electrical system malfunction. WARNING! Liftgate Handle NOTE: • In the event of a power malfunction, or the RKE transmitter is inoperative, insert the key into the liftgate lock cylinder and turn it to the right (manual lock models only).
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. However, because the gas pressure drops with temperature, it may be necessary to assist the props when opening the liftgate in cold weather. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All the seats in your vehicle are equipped with lap/ shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 39 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your authorized dealer and have it fixed. 5.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best. NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Second Row Center Lap/Shoulder Belt Operating Instructions The second row center lap/shoulder belt features a three point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach from the lower anchor when the seat is folded. The mini-buckle and shoulder belt can then be stored out of the way in the right side trim panel for added convenience. 43 2 1.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Grasp the mini-latch plate and pull the belt over the seat. 3. Route the shoulder belt to the inside of the right head restraint. Routing the Rear Center Shoulder Belt 4. When the belt is long enough to fit, insert the minilatch plate into the mini-buckle until you hear a “click.” Routing the Rear Center Shoulder Belt 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the belt to go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 45 on the shoulder belt. To loosen the lap belt if it is too tight, pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Connecting Mini-Latch to Buckle 7. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up Rear Center Seat Belt Buckled 8.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. To release the belt, push the red button on the buckle. slide the latch plate down the webbing to allow the belt to retract fully. Insert the mini-latch plate into the slot provided in the trim panel. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Watch for the Seat Belt Reminder Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. BeltAlert威 can be reactivated by repeating this procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Driver And Front Passenger Supplemental Restraint System (SRS) — Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity. This vehicle may also be equipped with side curtain airbags to protect the driver and passengers sitting next to a window. If the vehicle is equipped with side curtain airbags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! WARNING! (Continued) • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: 1. Children 12 years old and younger should always ride buckled up in the rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. If your vehicle has side airbags, do not lean against the door; airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⴖIf You Need Assistanceⴖ in Section 9 of this manual. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Side Curtain Airbags Above Side Windows (If Equipped) • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Seat Belt Reminder Light • Knee Impact Bolsters • Driver Inflatable Knee Blocker • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pretensioners How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up. WARNING! Ignoring the AIRBAG Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC module determines if a side collision is severe enough to require the side airbags to inflate. The side airbag control module will not detect roll over, front or rear collisions. The ORC module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON position. These include all of the items previously mentioned.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident. A modified vehicle may not comply with required Federal Motor Vehicle Safety Standards (FMVSS).
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper passenger side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE moment of airbag deployment, or near-deployment, and up to a quarter second of high-speed deceleration data during and/or after air bag deployment or neardeployment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavailable. NOTE: 1. A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indicative of a crash, but not severe enough to warrant airbag deployment. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 particular driver, vehicle, or crash, will be treated confidentially. Confidential data will not be disclosed by Chrysler LLC to any third party except when: • ⬙Time⬙ of airbag deployment (in terms of ignition cycles and vehicle mileage) 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved • Impact acceleration and angle 2.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraints Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and younger should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Child Restraints There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child: • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. belt tight; however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Follow the instructions of the child restraint manufacture. • Buckle the child into the seat according to the child restraint manufacturer’s directions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Your vehicle is equipped with the child restraint anchorage system called LATCH. The LATCH system provides for the installation of the child restraint without using the vehicle seat belt. All three rear seating positions have lower anchorages that are capable of accommodating LATCH-compatible child seats having flexible, webbingmounted lower attachments. Child seats with fixed lower attachments must be installed in the outboard positions only.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the seat back. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.).
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 䡵 uconnect威 phone — If Equipped . . . . . . . . . . . . 83 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 79 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 85 ▫ Automatic Dimming Inside Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . .
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Voice Recognition System (VR) Operation . . . 112 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 114 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . 117 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ Front Seat Adjustment . . . . . . . . . . . . . . . . . 117 ▫ Manual Seat Height Adjustment — If Equipped .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Daytime Running Lights (DRL) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 131 䡵 Windshield Wipers And Washers . . . . . . . . . . 131 ▫ Windshield Wiper Operation . . . . . . . . . . . . 131 ▫ Intermittent Wiper System . . . . . . . . . . . . . . 132 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 132 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 133 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . .
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Opening The Sunroof . . . . . . . . . . . . . . . . . 145 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . 154 ▫ Closing The Sunroof . . . . . . . . . . . . . . . . . . 146 ▫ Cargo Light/Removable Self-Recharging Flashlight — If Equipped . . . . . . . . . . . . . . . 154 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 146 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . 146 ▫ Venting Sunroof — Express . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Inside Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror. 81 Power Mirrors — If Equipped The control for the power mirrors is located on the drivers door trim panel.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror. Mirror Directions WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirrors — If Equipped To use the vanity mirror, rotate the sun visor down and swing the mirror cover upward. Vanity Mirror Sun Visor Sliding Feature The sun visors may be extended out to provide more coverage of the side glass. 83 uconnect姞 phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect威 phone. Refer to your “Navigation User’s Manual” for uconnect威 phone operating instructions for these radios.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The uconnect威 phone requires a cellular phone equipped with the Bluetooth威 ⬙Hands-Free Profile,⬙ Version 0.96 or higher. See the uconnect威 website for supported phones. For uconnect威 customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Button The rearview mirror contains the microphone for the system (depending on the type of mirror and radio equipped), and either the radio or the mirror has the two control buttons (PHONE Button and VOICE RECOGNITION button) that will enable you to access the system. Voice Recognition Button Actual button location may vary with the radio. The individual buttons are described in the “Operation” section.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For certain operations, compound commands can be used. For example, instead of saying ⬙Setup⬙ and then ⬙Phone Pairing,⬙ the following compound command can be said: ⬙Setup Phone Pairing.⬙ • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 To complete the pairing process, you will need to reference your cellular phone Owner’s Manual. The uconnect威 website may also provide detailed instructions for pairing. • For identification purposes, you will be prompted to give the uconnect威 phone a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dial by Saying a Number • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Dial.⬙ • The system will prompt you to say the number you want to call. • For example, you can say ⬙234-567-8901⬙. • The uconnect威 phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry. Use of long names helps the voice recognition and it is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Automatic download and update, if supported, begins as soon as the Bluetooth威 wireless phone connection is made to the uconnect威 phone, for example, after you start the vehicle. • A maximum of 1000 entries per phone will be downloaded and updated every time a phone is connected to the uconnect威 phone. • Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The phone handset must support Bluetooth威 OBEX transfers of phonebook entries to use this feature. • Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth威, and you may see a message on the phone display that the Bluetooth威 link is busy. In this case, the user must first disconnect or drop the Bluetooth威 connection to the uconnect威 phone, and then send the address book entry via Bluetooth威.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a cellular and a home number, but you can add ”John Doe’s” work number later using the ⬙Phonebook Edit⬙ feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete/Erase “All” uconnect威 Phonebook Entries • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Erase All.⬙ • The uconnect威 phone will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. • Note that only the phonebook in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the uconnect威 phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the uconnect威 phone. Check with your cellular service provider for the features that you have.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section. Place/Retrieve a Call From Hold To put a call on hold, press the PHONE button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the PHONE button until you hear a single beep.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the PHONE button until you hear a single beep. Redial • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Redial.⬙ • The uconnect威 phone will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. If the phone is not reachable and the uconnect威 phone is operational, you may reach the emergency number as follows: • Continue to follow the system prompts to complete the language selection. • Press the PHONE button to begin. After selecting one of the languages, all prompts and voice commands will be in that language.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say ‘Setup’, followed by ‘Emergency’. • The uconnect威 phone does slightly lower your chances of successfully making a phone call as to that for the cell phone directly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.⬙ Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You can use your uconnect威 phone to access a voice mail system or an automated service, such as a paging service or automated customer service line.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is asking ⬙Would you like to pair a phone, clear a...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE phone, the audio will be played through your vehicle’s audio system. The uconnect威 phone will work the same as if you dial the number using voice recognition. NOTE: Certain brands of cellular phones do not send the dial ring to the uconnect威 phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Bluetooth威 connection between a uconnect威 phone paired cellular phone and the uconnect威 phone, follow the instructions described in your cellular phone User’s Manual. Select Another Cellular Phone This feature allows you to select and start using another phone paired with the uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete uconnect威 phone Paired Cellular Phones • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete⬙ and follow the prompts. • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone you wish to delete.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This procedure may be repeated with a new user. The system will adapt to the last trained voice only. • Performance is maximized under: To restore the Voice Recognition system to factory default settings, enter the Voice Training session via the above procedure and follow the prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • It is not recommended to store similar sounding names in the uconnect威 phonebook. • Phonebook (Downloaded and uconnect威 phone Local) name recognition rate is optimized when the entries are not similar. • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bluetooth威 Communication Link Cellular phones have been found to lose connection to the uconnect威 phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Your cellular phone is recommended to remain in Bluetooth威 ON mode. Power-Up After switching the ignition key from OFF to either the ON or ACC position, or after a language change, you must wait at least five seconds prior to using the system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 3
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 3
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call uconnect威 Tutorial try again voice training work yes 111 3
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command. Pressing the VR button while the system is speaking is known as “barging in.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Recognition system is speaking.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio FM To switch to the FM band say “FM” or “Radio FM”.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording you may press the VR button to stop recording. You proceed by saying one of the following commands: − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup say “Setup”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, uconnect威 phone Voice Training feature may be used. 117 SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. 1.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! Manual Seat Height Adjustment — If Equipped The driver’s seat height can be raised or lowered by using the handle on the outboard side of the seat to adjust the driving position. • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar — If Equipped The lumbar adjustment handle is located on the outboard side of the driver’s seat. To increase or decrease support, rotate the handle up or down. 119 Driver’s Seatback Recline To recline: 1. Lean forward before lifting the handle, then lean back to the desired position and release the handle. 2. Lift the handle to return the seatback to an upright position.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraints so that the upper edge is as high as practical. To raise the head restraint, pull up on the head restraint. To lower the head restraint, press the button and push down on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low, and none for Off. Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Front Passenger Seat To fold the front passenger seat, lift the recliner handle to the full upward position and push the seatback forward until it rests on the seat cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to move the seat forward and flat.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Rear Seat — If Equipped For additional comfort, pull the strap forward just enough to release the seatback latch. Reclining Rear Seat Strap Then push the seatback to a reclined position, approximately 35 degrees maximum, and release the strap. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 3 Hood Release Lever Safety Catch 2. Move the safety catch located under the front edge of the hood, near the center and raise the hood. Lift the hood prop rod, clipped to the left side (right side facing hood) of the engine compartment, to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 8 in (20 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 3 Headlight Control Dimmer Control To change the brightness of the instrument panel lights, rotate the center portion of the multifunction lever up or down. Lights-on Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver when the driver’s door is opened.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped The front fog light switch is on the multifunction lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the multifunction lever. Fog Light Control NOTE: The fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 High Beam/Low Beam Select Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam. 3 Turn Signal Control If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash-to-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the multifunction lever is released. NOTE: If the multifunction lever is held in the flash-topass position for more than 30 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash-to-pass operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (DRL) — If Equipped The high beam headlights will come on as Daytime Running Lights (DRL) at DRL intensity, which is a lower intensity then the normal high beams. The DRL’s will come on whenever the ignition is ON, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the shift lever is in any position except for PARK.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Select the delay interval by turning the end of the lever. Rotate the knob upward (clockwise) to decrease the delay time and downward (counterclockwise) to increase the delay time. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every second.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Mist Control 133 CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the steering column, push down on the lever below the multifunction lever. With one hand firmly on the wheel, move the steering column up or down as desired. Push the lever back up to lock the column firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 reactivated by pushing the Electronic Speed Control switch ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system off, push the ON/OFF button a second time. The CRUISE indicator will turn off. The system should be turned off when not in use.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle has reached the desired speed, press down on the Electronic Speed Control lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the SET DECEL button once will result in a 1 mph (1.6 km/h) speed decrease. Each time the button is tapped, speed decreases. Manual Transaxle Pressing the clutch pedal will disengage the speed control. A slight increase in engine RPM before the Electronic Speed Control disengages is normal. Vehicles equipped with manual transaxles may need to be shifted into a lower gear to climb hills without speed loss.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed Control. GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink威 unit operates off your vehicle’s battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the hand-held transmitter 1–3 in (3-8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLink威 button and the hand-held transmitter button until the HomeLink威 indicator changes from a slow to a rapidly blinking light, then release both the HomeLink威 and hand-held transmitter buttons. Watch for the HomeLink威 indicator to change flash rates.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 141 6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink姞 Button To re-program a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Programming Homelink威 Step 2 and follow all remaining steps.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: POWER SUNROOF — IF EQUIPPED The power sunroof switch is located in the reading light. 1. This device may not cause harmful interference 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Closing the Sunroof Manual Mode To close the sunroof, press and hold the switch in the forward position. Again, any release of the switch will stop the movement and the sunroof will remain in a partial close condition until the switch is pushed and held forward again. To ensure sunroof is fully closed, press and hold switch until sunroof has completely stopped moving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Venting Sunroof — Express Press and hold the “Vent” button, and the sunroof will open to the vent position. This is called “Express Vent”, and will occur regardless of the sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS There is a standard 12-Volt power outlet located in the instrument panel for added convenience. This outlet can power cell phones, electronics and other low power devices.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! CAUTION! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED A 115-Volt (150-Watt) AC power inverter is located on the rear of the center console for added convenience. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WARNING! CAUTION! (Continued) To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Your vehicle is equipped with four cupholders. There are two cupholders located in the front. Rear Cupholders Front Cupholders There are two cupholders behind the center console for rear passengers. CONSOLE FEATURES The floor console’s sliding armrest moves forward 3 in (76.2 mm) to accommodate shorter drivers. The armrest lid also includes a unique flip pocket for storing a phone or an MP3 player.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! Do not operate this vehicle with the console compartment lid in the open position. Cell phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. Floor Console Flip Pocket NOTE: The flip pocket and console lid features are intended to be used in the upright or open position only while the vehicle is parked.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Cargo Light/Removable Self-Recharging Flashlight — If Equipped The dual-function light is mounted in the headliner above the cargo area to illuminate the cargo area, and part of it snaps out of the bezel to serve as a flashlight when needed. The flashlight features two bright LED light bulbs and is powered by rechargeable lithium batteries that recharge when snapped back into place for convenience. Press in on the flashlight to release it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. To install the Cargo Cover, insert either end of the cover into one of the two notches located in the rear trim panels. With one of the cover ends installed, push inward on the opposite end and install it into the same notch location of the rear trim panel.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. WARNING! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 WARNING! Rear Cargo Area Cargo Tie-Down Loops There are two D-rings installed in the cargo area for securing cargo. • Cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision. • To help protect against personal injury, passengers should not be seated in the rear cargo area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE activate the wiper. The rear wiper operates in an intermittent mode only. Rotating the center of the switch all the way forward will turn on the wash function. The wash pump will continue to operate as long as the button is pressed. Upon release, the wipers will cycle two times before returning to the set position.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE approximately 10 minutes. For an additional five minutes of operation, press the switch a second time. To prevent excessive battery drain, use the defroster only when the engine is operating. CAUTION! Use care when washing the inside of the rear window to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 NOTE: The use of the Cooled Beverage Storage Bin is for nonperishable beverages only. To operate the beverage cooler, pull the slide control about 0.5 in (12 mm) toward the passenger compartment. This will allow cool air to enter the beverage cooler. To shut off the beverage cooler when not in use, push the slide control back 0.5 in (12 mm). This will prevent cool air from entering the passenger compartment when in heat mode.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 166 ▫ Average Fuel Economy . . . . . . . . . . . . . . . . 184 䡵 Instrument Cluster – Base . . . . . . . . . . . . . . . 167 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . 184 䡵 Instrument Cluster – Premium . . . . . . . . . . . . 168 ▫ Elapsed Time . . . . . . . . . . . . . . . . . . . . . . . 185 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 169 ▫ Tire Pressure Monitor (TPM) . .
164 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play, DVD-Video) . . . 198 䡵 Sales Code RES — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) . . . . . . . . . . . . . . . 208 ▫ Notes On Playing MP3/WMA Files . . . . . . . 200 ▫ Operating Instructions — Radio Mode . . . . . 208 ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . 203 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Info Button (CD Mode For MP3 Play) . . . . . . 228 䡵 uconnect威 studios (Satellite Radio) — If Equipped (REN/REQ/RER/RES/REU Radios Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 229 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 230 ▫ Selecting uconnect威 studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
166 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 - Air Outlet - Demisters - Instrument Cluster - Radio 5 6 7 8 - Upper Glove Compartment Lower Glove Compartment/Beverage Cooler – If Equipped Storage Bins Climate Controls 9 - Heated Seat Switches – If Equipped 10 - Hazard Warning Flasher 11 - ESP OFF Switch – If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 167 INSTRUMENT CLUSTER – BASE 4
168 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This indicates that the fuel filler door is located on the left side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
170 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealership for service if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 4. Speedometer The Speedometer shows the vehicle speed in miles per hour and/or kilometers per hour (mph/kph). 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 8. Airbag Warning Light This light turns on and remains on for seven seconds as a bulb check, when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 9.
172 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Engine Temperature Warning Light This light warns of an overheated engine condition. As temperatures rise and the gauge approaches H , this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H , the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool.
UNDERSTANDING YOUR INSTRUMENT PANEL Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
174 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
UNDERSTANDING YOUR INSTRUMENT PANEL means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure: 1.
176 UNDERSTANDING YOUR INSTRUMENT PANEL 17. Cruise Indicator — If Equipped This indicator shows that the Speed Control system is ON. 18. Trip/Odometer Display Reset Button Press this button to change the display from odometer to either of the two trip odometer settings. Trip A or Trip B will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 miles (0 km). The odometer must be in Trip mode to reset. 19.
UNDERSTANDING YOUR INSTRUMENT PANEL 21. Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated. If the vehicle electronics sense that the vehicle has traveled about one mile with the turn signals on, a continuous chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 22. Front Fog Light Indicator — If Equipped This light shows when the front fog lights are ON. 23.
178 UNDERSTANDING YOUR INSTRUMENT PANEL brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer. 25. High Beam Indicator This indicator shows that the headlights are on high beam. Push the multifunction lever forward to switch the headlights to high beam, and pull toward yourself (normal position) to return to low beam. 26.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is necessary. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.
180 UNDERSTANDING YOUR INSTRUMENT PANEL 28. Electronic Vehicle Information Center Display — If Equipped When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. Refer to the Electronic Vehicle Information Center (EVIC) in this section for more information. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — If Equipped The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 The EVIC consists of the following: • Left Front Turn Signal Light Out (with a single chime) • System Status • Left Rear Turn Signal Light Out (with a single chime) • Vehicle information warning message displays • Right Front Turn Signal Light Out (with a single chime) • Personal settings (customer programmable features) • Compass heading • Outside temperature display • Trip computer functions • uconnect威 phone displays — If equipped • Audio mode display • Tir
182 UNDERSTANDING YOUR INSTRUMENT PANEL • Gate Ajar (with a single chime) • Headlights On • Key In Ignition • Check TPM System • Oil Change Required Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The “Change Oil” message will flash in the instrument cluster odometer for approximately 5 seconds after a single chime has sounded to indicate the next scheduled oil change interval.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 • Distance To Empty (DTE) EVIC Functions • Elapsed Time • Tire Pressure Monitor (TPM) • Personal Settings EVIC Button Press the EVIC button until one of the following functions are displayed on the EVIC: • Compass/Temperature/Audio • Average Fuel Economy To Reset The Display Pressing and holding the EVIC button once will clear the function currently being displayed. Reset will only occur if a resettable function is currently being displayed.
184 UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature/Audio Press and release the EVIC button to display one of eight compass headings to indicate the direction the vehicle is facing, the outside temperature and the current radio station. For additional information regarding the compass, refer to “Personal Settings (Customer Programmable Features)” in this section. Average Fuel Economy Shows the average fuel economy since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position. Tire Pressure Monitor (TPM) Refer to “Tire Pressure Monitoring System (TPMS)” under “Starting and Operating” in Section 5.
186 UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock On Exit When ON is selected all the vehicle’s doors will unlock when the driver’s door is opened if the vehicle is stopped (manual transmissions) or the vehicle is stopped and the transmission is in PARK or NEUTRAL position (automatic transmissions). Press and hold the EVIC button when in this display until “ON” or “OFF” appears to make your selection.
UNDERSTANDING YOUR INSTRUMENT PANEL when exiting the vehicle. Press and hold the EVIC button when in this display until 0, 30, 60, or 90 appears to make your selection. Delay Power Off to Accessories Until Exit When this feature is selected, the power window switches, radio, uconnect威 phone, power sunroof, and power outlets will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle door will cancel this feature.
188 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: A good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To ensure compass accuracy, the compass variance should be properly set according to the variance map for the zone where the vehicle will be driven.
UNDERSTANDING YOUR INSTRUMENT PANEL press and release (less than one second) the EVIC button several times until “Compass Variance” is highlighted. The “Compass Variance” message and the current variance zone number will be displayed. To change the zone, press and hold (longer than two seconds) the EVIC button to increment the variance one step. Repeat as necessary, with individual long (for at least one second) EVIC button presses for each increment, until the desired variance is achieved.
190 UNDERSTANDING YOUR INSTRUMENT PANEL calibration mode. The CAL indicator will come on continuously in the EVIC display to indicate that the compass is now in the calibration mode, and that the vehicle can now be driven to calibrate. 5. To complete the compass calibration, drive the vehicle in one or more complete 360–degree circle under 5 mph (8 km/h) in an area free from power lines and large metallic objects, until the “CAL” indicator turns off. The compass will now function normally.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
192 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button uconnect威 phone — If Equipped Press this button to operate the uconnect威 phone feature (if equipped). Refer to “uconnect威 phone” in Section 3. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With uconnect” message will display on the radio screen. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display.
194 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk To
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
196 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The available selections for each of the above entries varies depending upon the disc. TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes. • These selections can only be made while playing a DVD. • Player Defaults - Selecting this item will allow the user to scroll through the following items and set defaults according to customer preference.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 down and selecting ⬙other.⬙ Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select. Aspect Ratio — If Equipped Selecting this item allows you to choose between wide screen, pan scan, and letter box. Subtitle Language — If Equipped Selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc).
198 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components. NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
200 UNDERSTANDING YOUR INSTRUMENT PANEL The disc can be ejected with the radio and ignition OFF. SEEK Button (CD MODE) Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow you to scroll through the tracks faster in CD and MP3/MWA modes.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. Multisession disc formats are supported by the radio.
202 UNDERSTANDING YOUR INSTRUMENT PANEL frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 WMA Specification WMA Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48 160, 128, 144, 24, 22.
UNDERSTANDING YOUR INSTRUMENT PANEL • Number of files and folders - Loading times will increase with more files and folders To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc.
204 UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the AUX button will change the mode to auxiliary device if the AUX jack is connected. NOTE: The AUX device must be turned on and the device’s volume set to the proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. SEEK Button (Auxiliary Mode) No function. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - uconnect威 studios (Satellite Radio) (If Equipped) Refer to “uconnect威 studios (Satellite Radio)” in this section. Operating Instructions - Video Entertainment System (VES)™ (If Equipped) Refer to separate “Video Entertainment System (VES)™ Guide.” Dolby威 Manufactured under license from Dolby威 Laboratories. ⬙Dolby威⬙ and the double-D symbol are trademarks of Dolby威 Laboratories.
206 UNDERSTANDING YOUR INSTRUMENT PANEL Refer to your uconnect威 tunes (REN) or (RER) user’s manual for detailed operating instructions. Operating Instructions — Voice Recognition System (VR) — If Equipped For the radio, refer to “Voice Recognition System (VR)” in Section 3. Operating Instructions — uconnect姞 phone — If Equipped Refer to “uconnect威 phone” in Section 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 6. To save the new time setting, touch the screen where the word “Save” is displayed. Changing Daylight Savings Time When selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.
208 UNDERSTANDING YOUR INSTRUMENT PANEL Changing the Time Zone 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ON/VOLUME control knob to the right increases the volume, and to the left decreases it.
210 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones.
UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.
212 UNDERSTANDING YOUR INSTRUMENT PANEL • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.
UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF. NOTE: Ejecting with the ignition OFF is not allowed on convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD.
214 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next randomly selected track. Press the RND button a second time to stop Random Play. Notes on Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited.
UNDERSTANDING YOUR INSTRUMENT PANEL exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a threecharacter extension) • Level 2: 31 (including a separator ⬙.⬙ and a threecharacter extension) Multisession disc formats are supported by the radio.
216 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 24, 22.05, 16 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. 217 SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate.
218 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With uconnect” message will display on the radio screen. TIME Button Press the TIME button to alternate locations of the time and frequency display. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3.
220 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40
222 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC/AUX Button Pressing the DISC/AUX button will allow you to switch from AM/FM modes to DISC/AUX mode.
224 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 RW/FF Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. AM/FM Button Press the button to select either AM or FM mode.
226 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 24, 22.05, 16 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
228 UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is OFF). Operating Instructions - uconnect威 phone (If Equipped) Refer to “uconnect威 phone” in Section 3. Operating Instructions - uconnect威 studios (Satellite Radio) (If Equipped) Refer to “uconnect威 studios (Satellite Radio)” in this section.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Your Vehicle Identification Number.
UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around the trunk lid antenna (if equipped). Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna.
232 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button — Except REU Radio Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). INFO Button — REU Radio Pressing the INFO button will display information about Artist, Song Title, and Composer (if available).
UNDERSTANDING YOUR INSTRUMENT PANEL made, you can seek up or down or scan the channels and the radio will tune to the next station matching the selected format. There is no time-out for this screen. Pressing the MUSIC TYPE button again will close the Music Type screen. Once closed, seek up, seek down, and scan will no longer be based on your selection.
234 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — uconnect姞 phone (If Equipped) Refer to “uconnect威 phone” in Section 3. Operating Instructions — Video Entertainment System (VES)™ (If Equipped) Refer to separate “Video Entertainment System (VES)™ Guide.” REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the right-hand control will switch modes to Radio or CD. The left-hand control is a rocker type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following describes the left-hand control operation in each mode. Radio Operation Press the top of the switch to SEEK up for the next listenable station.
236 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Mode Control (Air Direction) The mode control allows you to choose from several patterns of air distribution as identified by the symbols. 4 Climate Control The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The controls are as follows: Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow.
238 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demister outlets with a small amount through the defrost outlet. Mix Air is directed through the floor, defrost and side window demister outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For maximum airflow to the rear seat passengers, the center instrument panel outlets can be aimed, so that the left center outlet is directed toward the right rear passenger and the right center outlet is directed toward the left rear passenger. Fan Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control from the left (OFF) to the right position.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Circulation Control Use this button to choose between outside air intake or recirculation of the air inside the vehicle. A light will illuminate when you are in recirculate mode. Only use the recirculate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather. NOTE: Continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning (MAX A/C) For maximum cooling select the air direction to either the Panel or Bi-Level position using the mode control. Press the A/C button and the recirculation button so that both lights are illuminated and set the temperature control to its coolest setting. NOTE: • Recirculation Mode will not operate in Floor, Mix or Defrost modes. • See “Circulation Control” in this section, for proper or extended use of this position.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, set mode to the mix or defrost position. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur. Interior fogging on the windshield can be quickly removed by using the defrost position. If the fogging problem persists, clean the inside window surfaces.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 249 䡵 Manual Transaxle — If Equipped . . . . . . . . . . 251 ▫ Manual Transmission — If Equipped . . . . . . 249 ▫ 5–Speed Manual Transaxle . . . . . . . . . . . . . . 251 ▫ Automatic Transmission — If Equipped . . . . 249 ▫ Recommended Shift Speeds . . . . . . . . . . . . . 253 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 249 ▫ Downshifting . . . . . . . . . . . . . . . . . . . . . . .
246 STARTING AND OPERATING 䡵 AutoStick威 — If Equipped . . . . . . . . . . . . . . . 257 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . 258 ▫ General Information . . . . . . . . . . . . . . . . . . 258 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 259 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . 259 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 䡵 Driving Through Water . . . . . . . . . . . . . . . . . 260 ▫ Flowing/Rising Water . . . . . .
STARTING AND OPERATING 247 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . 284 ▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . 295 ▫ Tire Pressures For High Speed Operation . . . 285 ▫ Premium System — If Equipped . . . . . . . . . 297 ▫ Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . 286 ▫ General Information . . . . . . . . . . . . . . . . . . 301 ▫ Compact Spare Tire — If Equipped . . . . . . . 286 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . .
248 STARTING AND OPERATING ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 307 䡵 Vehicle Loading ▫ Trailer And Tongue Weight . . . . . . . . . . . . . 314 . . . . . . . . . . . . . . . . . . . . . . 307 ▫ Towing Requirements . . . . . . . . . . . . . . . . . 315 ▫ Vehicle Certification Label . . . . . . . . . . . . . . 308 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 320 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
250 STARTING AND OPERATING and release when the engine starts. If the engine fails to start within 15 seconds, turn the ignition switch to the OFF position, wait 10 to 15 seconds, then repeat the normal starting procedure. Extremely Cold Weather (Below ⫺20°F Or ⫺29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended.
STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up.
252 STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. Use each gear in numerical order, do not skip a gear. Be sure the transaxle is in 1st gear, (not 3rd), when starting from a standing position. Damage to the clutch can result from starting in 3rd gear. For most city driving, you will find it easier to use only the lower gears. For steady highway driving with light accelerations, 5th gear is recommended.
STARTING AND OPERATING Recommended Shift Speeds To use your manual transaxle for optimal fuel economy, it should be upshifted as listed in the following table. Manual Transaxle Recommended Shift Speeds Units in mph (km/h) AccelEngine eration 1 to 2 2 to 3 3 to 4 4 to 5 Size Rate All En- Accel 14 (23) 23 (37) 29 (47) 45 (72) gines Cruise 12 (19) 18 (29) 25 (40) 32 (52) Downshifting Proper downshifting will improve fuel economy and prolong engine life.
254 STARTING AND OPERATING CAUTION! WARNING! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING NOTE: If a malfunction occurs, the transaxle will not shift out of PARK. Battery power is required to release the brake/transmission interlock system. There is a removable plug in the right side of the shifter housing that allows you to insert your finger to override the system. If this occurs, obtain service as soon as possible. 255 Gear Ranges DO NOT race the engine when shifting from PARK or NEUTRAL position into another gear range.
256 STARTING AND OPERATING Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the shift lever into the PARK position. The following indicators should be used to ensure that you have engaged the shift lever into the PARK position: WARNING! • Look at the shift indicator window on the shifter bezel to ensure it is in the PARK position.
STARTING AND OPERATING REVERSE Shift into this range only after the vehicle has come to a complete stop. NEUTRAL The engine may be started in this range. DRIVE This should be used for most driving and provides the best ratio for optimum drivability, fuel economy, and performance. AUTOSTICK姞 — IF EQUIPPED Autostick威 is a driver-interactive transmission that offers six manual ratio changes to provide you with more control.
258 STARTING AND OPERATING Operation NOTE: Autostick威 is not functional until the CVT warms up in cold weather. Autostick威 operation is activated in the DRIVE position by moving the shift lever side-to-side. Moving the shift lever to the (+) side will activate Autostick威 and shift up to the next higher manual ratio, unless you are already operating in or near Overdrive, in which case 6th ratio will be selected.
STARTING AND OPERATING • If the system detects powertrain overheating, the transmission will revert to the automatic shift mode and remain in that mode until the powertrain cools off. • If the system detects a problem, it will disable the Autostick威 mode and the transmission will return to the automatic mode until the problem is corrected. 259 WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels.
260 STARTING AND OPERATING 2. Slow down if the road has standing water or puddles. 3. Replace the tires when tread wear indicators first become visible. 4. Keep the tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle.
STARTING AND OPERATING 261 CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
262 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. 263 apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used.
264 STARTING AND OPERATING PARKING BRAKE When the parking brake is applied with the ignition ON, the Brake Light in the instrument cluster will come on. NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver.
STARTING AND OPERATING As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. You should always apply the parking brake before leaving the vehicle. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
266 STARTING AND OPERATING If either of the two hydraulic systems lose normal capability, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the brake warning indicator will light.
STARTING AND OPERATING WARNING! (Continued) • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. The ABS light monitors the ABS System.
268 STARTING AND OPERATING ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
STARTING AND OPERATING enhance vehicle stability and control in various driving conditions and are commonly referred to as ESP. Anti-Lock Brake System (ABS) This system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lockup and help avoid skidding on slippery surfaces during braking. Refer to “Anti-Lock Brake System” in this section of the manual for more information about ABS.
270 STARTING AND OPERATING WARNING! (Continued) • The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. Traction Control System (TCS) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability.
STARTING AND OPERATING • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. ESP Indicator Light The “ESP Indicator Light” located in the instrument cluster, starts to flash as soon as the tires lose traction and the ESP system becomes active. If the “ESP Indicator Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions.
272 STARTING AND OPERATING ESP Operating Modes The ESP system has two available operating modes. Full On This is the normal operating mode for ESP. Whenever the vehicle is started the ESP system will be in this “On” mode. This mode should be used for most driving situations. ESP should only be turned to “Partial Off” for specific reasons as noted below. Partial Off This mode is entered by momentarily depressing the ESP OFF switch.
STARTING AND OPERATING ESP/BAS Warning Light and ESP Indicator Light The malfunction indicator for the ESP is combined with the BAS indicator. The yellow “ESP/BAS Warning Lamp” and the yellow “ESP Indicator Light” in the instrument cluster both come on when the ignition switch is turned to the ON position. They should both go out with the engine running. If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or BAS system, or both.
274 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING • LT (Light Truck) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the size designation. Example: LT235/85R16. • Temporary spare tires are high-pressure compact spares designed for temporary emergency use only. 275 Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
276 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 277 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
278 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard 279 This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
280 STARTING AND OPERATING axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
STARTING AND OPERATING NOTE: • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. 281 • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs (392 kg).
282 STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
284 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours or driven less than 1 mile (1.6 km) after a three hour period.
286 STARTING AND OPERATING loading may be required for high-speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
STARTING AND OPERATING vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. 287 Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! WARNING! • Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). • Temporary-use spare tires have limited tread life.
288 STARTING AND OPERATING WARNING! WARNING! The limited-use spare tires are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than 50 mph (80 km/h). Keep it inflated to the cold tire inflation pressure listed on either your tire placard or limited-use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING 289 Many states have laws requiring tire replacement at this point. Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure 5 • Distance driven WARNING! 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
290 STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed.
STARTING AND OPERATING 291 WARNING! (Continued) CAUTION! • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Damage to the vehicle may result if tire chains are used. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. TIRE CHAINS Due to limited clearance, tire chains are not recommended.
292 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING 293 TIRE PRESSURE MONITORING SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.
294 STARTING AND OPERATING For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 26 psi (179 kPa). This tire pressure is sufficiently low enough to turn ON the Tire Pressure Monitoring Telltale Light.
STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. 295 • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in the tire. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. Base System This is the TPMS warning indicator located in the instrument cluster.
296 STARTING AND OPERATING • Four Tire Pressure Monitoring Sensors • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low.
STARTING AND OPERATING 1. The compact spare tire does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the tire pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the Tire Pressure Monitoring Telltale Light will still turn ON due to the low tire. 3.
298 STARTING AND OPERATING The TPMS consists of the following components: • Receiver Module • Four Tire Pressure Monitoring Sensors every ignition cycle for each condition that it detects. In addition, the EVIC will display a graphic of the pressure value(s) with the low tire(s) flashing.
STARTING AND OPERATING 299 display to the vehicle’s recommended cold placard pressure value. The system will automatically update, the graphic display of the pressure value(s) will stop flashing, and the Tire Pressure Monitoring Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) to receive this information.
300 STARTING AND OPERATING will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors.
STARTING AND OPERATING limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
302 STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline”. “Reformulated gasolines” contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. CAUTION! DO NOT use gasolines containing Methanol or E85 Ethanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components.
STARTING AND OPERATING 303 If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: More extensive repairs will be required for prolonged exposure to E-85 fuel. • operate in a lean mode MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT.
304 STARTING AND OPERATING MMT is prohibited in Federal and California reformulated gasolines. Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period of time.
306 STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. CAUTION! • A poorly fitting gas cap may cause the Malfunction Indicator Light (MIL) to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the MIL will come on. Be sure the gas cap is tightened every time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
308 STARTING AND OPERATING Vehicle Certification Label Your vehicle has a Vehicle Certification Label attached to the driver’s door B-Pillar. The label contains the following information: • Name of manufacturer • Month and year of manufacture • Gross Vehicle Weight Rating (GVWR) • Vehicle Identification Number (VIN) • Type of Vehicle • Month, Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN).
STARTING AND OPERATING Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added. Overloading The load carrying components (springs, tires, wheels, etc.
310 STARTING AND OPERATING TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
STARTING AND OPERATING WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue Weight (TW) The tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle.
312 STARTING AND OPERATING consistent steering and brake control and thereby enhancing towing safety. The addition of a friction/ hydraulic sway control also dampens sway caused by traffic and crosswinds, contributing positively to tow vehicle and trailer stability. Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier Tongue Weights (TW) and may be required depending on Vehicle and Trailer configuration/loading to comply with GAWR requirements.
STARTING AND OPERATING Trailer Hitch Classification Definitions Class Max. Trailer Hitch Industry Standards Class I - Light Duty 2,000 lbs (907 kg) Refer to the “Trailer Towing Weights (Maximum Trailer Weight Ratings)” chart for the Maximum Gross Trailer Weight (GTW) towable for your given drivetrain. 313 All trailer hitches should be professionally installed on your vehicle.
314 STARTING AND OPERATING Note 1 – The trailer tongue weight must be considered as part of the combined weight of occupants and cargo and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to “Tire–Safety Information” under “Starting and Operating” in Section 5. Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information placard” under “Tire Safety Information” in Section 5 of this manual for the maximum combined weight of occupants and cargo for your vehicle.
316 STARTING AND OPERATING WARNING! (Continued) Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (this requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). 317 − When replacing tires, refer to “Tires–General Information” for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits.
318 STARTING AND OPERATING CAUTION! WARNING! (Continued) If the trailer weighs more than 1,000 lbs (450 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • Towing any trailer will increase your stopping distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you.
STARTING AND OPERATING 319 The electrical connections are all complete to the vehicle, but you must mate the harness to a trailer connector. Refer to the following illustrations.
320 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in 1st gear to avoid excessive clutch slippage. Electronic Speed Control — If Equipped − Do not use in hilly terrain or with heavy loads.
STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 324 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 327 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 324 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . . 331 䡵 Automatic Transaxle Overheating . . . . . . . . . . 325 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 333 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 326 䡵 Towing A Disabled Vehicle . . .
324 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located on the instrument panel, below the radio. Press the switch to turn on the Hazard Warning flashers. When the Hazard Warning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off flashers. Do not use this emergency warning system when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to floor, and the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H”, pull over when safe and stop the vehicle with the engine at idle.
326 WHAT TO DO IN EMERGENCIES requested speed. If the high speed is maintained, the overheating will reoccur, as before, in a cyclic fashion. JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the load floor cover and remove the hold down. Preparations For Jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. 327 5. Turn on the Hazard Warning flasher. 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
328 WHAT TO DO IN EMERGENCIES WARNING! (Continued) WARNING! (Continued) • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack.
WHAT TO DO IN EMERGENCIES 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. 329 CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 3. 3. There are two front jacking locations and two rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts, the rear ones by two rectangular cutouts.
330 WHAT TO DO IN EMERGENCIES WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. 5. Using the swivel wrench raise the vehicle by turning the jack screw to the right.
WHAT TO DO IN EMERGENCIES 9. Remove the wheel blocks and lower the jack until it is free. Reassemble the lug wrench to the jack assembly and stow it in the spare tire area. Secure the assembly using the means provided. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 10.
332 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way and may be damaged. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle.
WHAT TO DO IN EMERGENCIES WARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over the battery when attaching the clamps or allow the clamps to touch each other. If acid splashes in your eyes or on your skin, flush the contaminated area immediately with large quantities of water. • A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
334 WHAT TO DO IN EMERGENCIES front wheels. Then shift back and forth between REVERSE and 1st gear. Usually the least accelerator pedal pressure to maintain the rocking motion without spinning the wheels is most effective. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause axle, tire damage or failure. A tire could explode and injure someone.
WHAT TO DO IN EMERGENCIES CAUTION! DO NOT flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. Manual Transaxle • Front Wheel Drive (FWD) or All Wheel Drive (AWD) vehicles can be flat towed (all four wheels on the ground) with the transmission in NEUTRAL. • FWD vehicles can be towed with the front wheels elevated. • FWD or AWD vehicles can be towed on a flatbed truck (all wheels off the ground).
336 WHAT TO DO IN EMERGENCIES Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. A dolly should be used under the front wheels if the rear wheels are raised. Proper towing equipment is necessary to prevent damage to the vehicle. Battery power is required to release the brake/ transmission interlock system. There is a removable plug in the right side of the shift lever housing that allows you to insert your finger to override the system.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.0L . . . . . . . . . . . . . 339 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 344 䡵 Engine Compartment — 2.4L . . . . . . . . . . . . . 340 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 347 䡵 Onboard Diagnostic System — OBD II . . . . . . 341 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 347 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 341 ▫ Maintenance-Free Battery . . . . . . . . . . .
338 MAINTAINING YOUR VEHICLE ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 353 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 359 ▫ Automatic Transaxle (CVT) — If Equipped . . 361 ▫ Manual Transaxle — If Equipped . . . . . . . . . 362 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 362 䡵 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 ▫ Integrated Power Module (IPM) . . . . . . . . . .
MAINTAINING YOUR VEHICLE 339 ENGINE COMPARTMENT — 2.
340 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
342 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL light off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration.
MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine.
344 MAINTAINING YOUR VEHICLE your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick. The range markings will consist of a crosshatch zone that says SAFE or a crosshatch zone that says MIN at the low end of the range and MAX at the high end of the range.
346 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy.
MAINTAINING YOUR VEHICLE environment. Contact your authorized dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All of this manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably.
348 MAINTAINING YOUR VEHICLE Maintenance-Free Battery The top of the maintenance-free battery is permanently sealed. You will never have to add water, nor is periodic maintenance required. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
MAINTAINING YOUR VEHICLE 349 CAUTION! (Continued) WARNING! • If a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage. • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you.
350 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R-134a air conditioning refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Make sure that they are not frozen to the glass before turning them on to avoid damaging the blade. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc.
352 MAINTAINING YOUR VEHICLE exhaust system each time the vehicle is raised for an oil change or lubrication. Replace as required. WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Exhaust Gas” in the Safety Tips section of this manual. The catalytic converter requires the use of unleaded fuel only.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
354 MAINTAINING YOUR VEHICLE WARNING! (Continued) • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
MAINTAINING YOUR VEHICLE 355 CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible.
356 MAINTAINING YOUR VEHICLE When adding engine coolant (antifreeze), a minimum solution of 50% recommended MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology), or equivalent, in water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant (antifreeze) solution.
MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
358 MAINTAINING YOUR VEHICLE long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions.
360 MAINTAINING YOUR VEHICLE when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. NOTE: If your vehicle is equipped with a manual transaxle , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system. The manual transaxle clutch release system should not require fluid replacement during the life of the vehicle.
MAINTAINING YOUR VEHICLE Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. NOTE: Do not allow petroleum-based fluid to contaminate the brake fluid as seal damage will result! Automatic Transaxle (CVT) — If Equipped Selection Of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance.
362 MAINTAINING YOUR VEHICLE (CVTF+4). CVTF+4 is an engineered product and its performance may be impaired by supplemental additives. Manual Transaxle — If Equipped Lubricant Selection Use only the manufacturers recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 3/16 in (4.
MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes of corrosion are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near sea coast localities.
364 MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open.
MAINTAINING YOUR VEHICLE heavy soil, use MOPAR威 Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only MOPAR威 cleaners are recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish.
366 MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp, soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rearview mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections on the windshield. Do not use protectants or other products which may cause undesirable reflections.
368 MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the seat belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the seat belts from the car to wash them. Replace the seat belts if they appear frayed or worn or if the buckles do not work properly. Dry with a soft cloth.
MAINTAINING YOUR VEHICLE Cavity Cartridge MiniFuse Fuse 8 30 Amp Green 9 40 Amp Green 10 20 Amp Yellow 11 15 Amp Lt Blue 12 20 Amp Yellow 13 20 Amp Yellow 14 15 10 Amp Red 40 Amp Green Description IOD Sense2 Cavity Cartridge MiniFuse Fuse 16 15 Amp Lt Blue Power Seats CCN Power Locks/ Interior Lighting Power Outlet 17 Ign Run/Acc Inverter 19 Pwr Run/Acc Outlet RR/Dome Lamp/ Cigar Lighter IOD CCN 20 RAD Fan Relay Battery Feed 22 18 21 10 Amp Red 40 Amp Green 20 Amp Yellow 15 Amp Lt Blue 10 Amp
370 MAINTAINING YOUR VEHICLE Cavity Cartridge MiniFuse Fuse 23 15 Amp Lt Blue 24 15 Amp Lt Blue 25 10 Amp Red 26 15 Amp Lt Blue 27 10 Amp Red 28 10 Amp Red 29 30 20 Amp Yellow Description ENG ASD Relay Feed 3 Power Sunroof Feed Cavity Cartridge MiniFuse Fuse 31 10 Amp Red 32 Heated Mirror (If Equipped) ENG ASD Relay Feed 2 IGN RUN Only ORC Feed IGN RUN ORC/OCM Feed Hot Car (No Fuse Required) Heated Seat (If Equipped) 30 Amp Pink 33 34 35 36 37 10 Amp Red 30 Amp Pink 40 Amp Green 30 Amp Pink Descr
MAINTAINING YOUR VEHICLE CAUTION! • When installing the IPM cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the IPM, and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
372 MAINTAINING YOUR VEHICLE LIGHTS BULBS — Exterior Bulb Number Low Beam/High Beam Headlight . . . . . . . . . . . . H13 Front Park/Turn Signal/Side Marker Light . . . . . . . . . . . . . . . . . . 3157AK or 3157A Front Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . 9145 Center High-Mounted Stop Light (CHMSL) . . . . . . . . . . . . . . . . . . . . . . LED Assembly Rear Turn/Tail/Stop . . . . . . . . . . . . . . . . . . . . . 3157 Backup Light . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE Tail Lights, Rear Turn Signals and Backup Lights 1. Remove the two push-pins from the tail light housing. 373 2. Grasp the tail light and pull firmly to disengage the light from the aperture panel.
374 MAINTAINING YOUR VEHICLE 3. Twist and remove socket from light. 4. Remove the bulb from the socket and replace.
MAINTAINING YOUR VEHICLE License Lights 375 2. Rotate the socket 1/4 turn counterclockwise. 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate.
376 MAINTAINING YOUR VEHICLE 3. Pull the bulb from the socket. Center High-Mounted Stoplight The light is an LED assembly. See your authorized dealer for replacement.
MAINTAINING YOUR VEHICLE 377 FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil with Filter 2.0L and 2.4L Engine (SAE 5W-20, API Certified) Cooling System * 2.0L and 2.4L Engine (MOPAR威 Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 13.6 Gallons Metric 51.5 Liters 4.5 Quarts 4.26 Liters 7.2 Quarts 6.
378 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade.
MAINTAINING YOUR VEHICLE 379 Chassis Component Automatic Transaxle (CVT) Manual Transaxle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 CVTF + 4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 382 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 382 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 382 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES oil if it has been six months since your last oil change and even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever comes first. Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change.
M A I N T E N A N C E S C H E D U L E S 8 384 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check the tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • Check all lights and other electrical items for correct operation. • Inspect the brake hoses and lines.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Replace the air conditioning filter.
M 386 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (except 2.4L PZEV). ❏ Adjust the parking brake on vehicles equipped with four-wheel disc brakes. ❏ Change the engine oil and engine oil filter.
M 388 MAINTENANCE SCHEDULES A I N 48,000 Miles (80,000 km) or 48 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. C E ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Inspect the brake linings; replace if necessary. Adjust the parking brake on vehicles equipped with four-wheel disc brakes. Replace the air conditioning filter. Replace the spark plugs (except 2.4L PZEV).
M 390 MAINTENANCE SCHEDULES A I N 72,000 Miles (120,000 km) or 72 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. C E ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Replace the air conditioning filter. ❏ Change the engine oil and engine oil filter.
M 392 MAINTENANCE SCHEDULES A I N 96,000 Miles (160,000 km) or 96 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. C E ❏ Inspect the brake linings; replace if necessary. S C H E D U L E S ❏ ❏ ❏ ❏ ❏ Replace the air conditioning filter. Inspect the CV joints. Inspect exhaust system.
MAINTENANCE SCHEDULES 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Replace the air conditioning filter. ❏ Change the engine oil and engine oil filter.
M 394 MAINTENANCE SCHEDULES A I N 120,000 Miles (200,000 km) or 120 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. C ❏ Inspect the brake linings; replace if necessary. E ❏ Adjust the parking brake on vehicles equipped with four-wheel disc brakes. S C H E D U L E S ❏ ❏ ❏ ❏ ❏ ❏ ❏ 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Replace the air conditioning filter. ❏ Change the engine oil and engine oil filter.
M 396 MAINTENANCE SCHEDULES A I N 144,000 Miles (240,000 km) or 144 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. C E ❏ Inspect the brake linings; replace if necessary. S C H E D U L E S ❏ ❏ ❏ ❏ ❏ Replace the air conditioning filter. Inspect the CV joints. Inspect exhaust system.
MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 403 ▫ Prepare For The Appointment . . . . . . . . . . . 401 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 403 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 401 䡵 Warranty Information (U.S. Vehicles Only) . . . .
400 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 405 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 407 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 406 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 407 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
402 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
404 IF YOU NEED CONSUMER ASSISTANCE the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
IF YOU NEED CONSUMER ASSISTANCE To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
406 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
408 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
410 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 266 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 355 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 351 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 304 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 347 Air Conditioner Maintenance . . . . . . . . . . . . . . . 349 Air Conditioning . . . . . . . . . . . . . . . . . . .
INDEX Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 Special Additives . . . . . . . . . . . . . . . . . . . . . . 361 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348 Keyless Transmitter Replacement (RKE) . . . . . . . 25 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Beverage Cooler . . . . . . . . . . . . . . . . . . . . . . . .
412 INDEX Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 157 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 83,236 Center High Mounted Stop Light . . . . . . . . . . . . 376 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 326 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . 276 Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . .
INDEX Corrosion Protection Cruise Light . . . . . Cupholders . . . . . . Customer Assistance .. ... ... .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 176 152 401 Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 59 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 343 Defroster, Rear Window . . . . . . . . . . . . . . . . . . .
414 INDEX Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 331 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Emission Control System Maintenance . . . . . . 342,382 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Break-In Recommendations . . . . . . . . . . . . . . . . 70 Checking Oil Level . . . . . . . . . . . . . . . . . . . . . 344 Cooling . . . . .
Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 361 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 263 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 378 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . 128,177,372 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . 123 Folding Rear Seat (Sedan) . . . . . . . . . . . . . . . . . .
416 INDEX General Information . . . . . . . . . . . . . . . . . 18,112,301 General Maintenance . . . . . . . . . . . . . . . . . . . . . 344 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Glove Compartment . . . . . . . . . . . . . . . . . . . . . . 160 Gross Axle Weight Rating . . . . . . . . . . . . . . . . . . 310 Gross Vehicle Weight Rating . . . . . . . . . . . . . 308,310 Hands-Free Phone (uconnect威) . . . . . . . . . . . . . . .
INDEX Integrated Power Module (Fuses) . . . . . . . . . . . . 368 Interior Appearance Care . . . . . . . . . . . . . . . . . . 365 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 132 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Jack Operation . . . . . . . . . . . . . . . . . . . . . . . 326,327 Jacking Instructions . . . . . . . . . . . . . . . . . . . . . . 327 Jump Starting . . . . . . . . . . .
418 INDEX Electronic Stability Program (ESP) Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 271,273 Engine Temperature Warning . . . . . . . . . . . . . . 172 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . 128,177,372 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 126 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 High Beam Indicator . . . . . . . . . . . . . . . . . . . .
INDEX Malfunction Indicator Light (Check Engine) . . 175,342 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 405 Manual Transaxle . . . . . . . . . . . . . . . . . . 249,251,362 Downshifting . . . . . . . . . . . . . . . . . . . . . . . . . 253 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . 362 Frequency of Fluid Change . . . . . . . . . . . . . . . 362 Lubricant Selection . . . . . . . . . . . . . . . . . . . . . 362 Map/Reading Lights . . . . . . . . . . . . . . . . . . . .
420 INDEX Opener, Garage Door (HomeLink威) . . . . . . . . . . . 138 Operator Manual (Owner’s Manual) . . . . . . . . . . . . 4 Outside Air Intake . . . . . . . . . . . . . . . . . . . . . . . 243 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Overheating, Engine . . . . . . . . . . . . . . . . . . . 169,324 Owner’s Manual (Operator Manual) . . . . . . . . . 4,405 Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 Panic Alarm . . . . . . . . . . . . . . . . .
INDEX Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 158 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 59 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 321 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . 47 Remote Control Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Security Alarm . . . . . . . . . . . . . . . . . . . . . . . . .
422 INDEX Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Seat Belts (Sedan) . . . . . . . . . . . . . . . . . . . . . . . . 36 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . 120 Heated . .
INDEX Speedometer and Odometer . . . . . . . . . . . . . . . . 167 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 Automatic Transmission . . . . . . . . . . . . . . . . . 249 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 250 Manual Transmission . . . . . . . . . . . . . . . . . . . 249 Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 249 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 262,263 Tilt Column . . . . . . . . . . . .
424 INDEX High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 285 Inflation Pressures . . . . . . . . . . . . . . . . . . . . . 284 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 289 Load Capacity . . . . . . . . . . . . . . . . . . . . . . . . 279 Pressure Monitor System (TPMS) . . . . . . . . . . . 293 Pressure Warning Light . . . . . . . . . . . . . . . . . . 172 Quality Grading . . . . . . . . . . . . .
INDEX Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Selection of Lubricant . . . . . . . . . . . . . . . . . . . 361 Transmission Range Indicator . . . . . . . . . . . . . . . . . . . . . . . 172 Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 25 Transmitter, Garage Door Opener (HomeLink威) . . 138 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . .
426 INDEX Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 364 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . . . 147 Window Airbag (Side Curtain) . . . . . . . . . . . . . . . 50 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 243 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . . 73 Windshield Washers . . . . .
Default Page Layout INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key RemovalLocking Doors With The KeyKey-In-Ignition ReminderSENTRY KEY Replacement KeysCustomer Key ProgrammingGeneral InformationVEHICLE SECURITY ALARM - IF EQUIPPED To Set The Security AlarmTo Disarm The SystemVehicle Security Alarm Manual OverrideREMOTE KEYLESS ENTRY - IF EQU
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Chrysler LLC 81-226-0939 Second Edition Printed in U.S.A.
