2008 Ram Truck 2008 OWNER’ S MANUAL 81-326-0827 First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
TABLE OF CONTENTS SECTION PAGE .............................................................3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .415 6 7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Van Conversions/Campers . . . . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 7 m Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 m Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. Vehicle Identification Number 7 NOTE: It is illegal to remove the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .12 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Locking Doors With The Key . . . . . . . . . . . . . .14 m Sentry Keyt . . . . . . . . . . . . . . . . . . . . . . . . . . .15 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . .16 ▫ Customer Key Programming . . . . . . . . . . . . . .17 ▫ General Information . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Illuminated Entry System — If Equipped . . . . . . .20 m Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 m Remote Keyless Entry (RKE) — If Equipped . . . . .21 ▫ Power Windows—If Equipped . . . . . . . . . . . . .32 ▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . .21 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .34 ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .22 m Occupant Restraints . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags . . . . . . . . . . .48 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .60 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .62 m Engine Break-In Recommendations . . . . . . . . . . .76 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 11 ▫ Transporting Passengers . . . . . . . . . . . . . . . . .77 ▫ Exhaust Gas . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic Transmission Place the shift lever in PARK. Turn the ignition switch to the LOCK position, and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Manual Transmission—If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide anti-theft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEYT The Sentry Keyt Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Exxon/Mobil Speedpass™, additional Sentry Keyst, or any other transponder-equipped components on the same key chain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system. All of the keys provided with your new vehicle have been programmed to the vehicle electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Key Programming If you have two valid Sentry Keyst, you can program new Sentry Keyst to the system by performing the following procedure: 1. Cut the additional Sentry Keyt Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed. General Information The Sentry Keyt system complies with FCC rules Part 15 and with RSS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. Automatic Transmission Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ON positions, and the brake pedal is depressed.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by an authorized dealer. To Disarm the System: Use the RKE transmitter to UNLOCK the door. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the SECURITY light will flash for 30 seconds. Check the vehicle for tampering.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED 21 To Unlock The Doors Press and release the UNLOCK button on the RKE transmitter once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and, if installed, the cargo lamp will turn on for 30 seconds.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Continue to hold the LOCK button at least four seconds, but no longer than 10 seconds, then press and hold the UNLOCK button while still holding the LOCK button. 4. Release both buttons at the same time. 5. This will allow you to unlock all doors on the first press of the UNLOCK button. 6. To reactivate this feature, repeat the above steps. To Lock The Doors Press and release the LOCK button on the RKE transmitter to lock all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Continue to hold the UNLOCK button, wait at least four seconds, but no longer than 10 seconds, then press and hold the LOCK button. Release both buttons at the same time. 4. To reactivate this feature, repeat the above steps. Using The Panic Alarm To activate the PANIC mode while the ignition is OFF, press and release the PANIC button on the RKE transmitter once.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your Remote Keyless Entry Transmitter (RKE) fails to operate from a normal distance, check for these two conditions: Transmitter Battery Service 1. Weak batteries in transmitter. The expected life of the batteries is from one to two years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With RKE transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start. How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • HAZARD switch off • BRAKE switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level, and • RKE PANIC button not pressed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote start will also cancel if any of the following occur: • If the engine stalls or RPM exceeds 2500. • Any engine warning lamp turns on. To Exit Remote Start Mode without Driving the Vehicle Press and release the REMOTE START button one time, or allow the engine to run for the entire 15-minute cycle.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key. Automatic Door Locks – If Equipped If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Automatic Door Lock Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1. Enter your vehicle and close all doors.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock On Exit — If Equipped This feature unlocks all of the doors of the vehicle when any door is opened. This will occur only after the vehicle has been shifted into the PARK position after the vehicle has been driven (shifted out of PARK and all doors closed). 4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times, ending in the LOCK position. (Do not start the engine). 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child protection door lock system. 31 To use the system, open each rear door, slide the lever UP to engage the locks and DOWN to disengage the child protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even, if the inside door LOCK is in the UNLOCKED position.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WINDOWS Power Windows—If Equipped Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and on the rear doors of Quad Cabt and Mega Cabt models. The windows will operate when the ignition switch is turned to the ON or ACC position, and for ten minutes after the ignition is turned OFF or a front door is opened. NOTE: The Power Accessory Delay feature will allow the power windows to operate for 10 minutes after the ignition is turned OFF. 33 WARNING! Never leave children alone in a vehicle.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window LOCKOUT Switch (4-Door Models Only) The window LOCKOUT switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCK button. To enable the window controls, press the window LOCK button again. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is extended long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 39 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that fits you best. In-Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Retractors (ALR) Mode – If Equipped Seatbelts, except for driver seatbelt, are equipped with an Automatic Locking Retractor (ALR) and/or a cinching latch plate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Center Lap Belts The center seating position for the Quad Cabt front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a 9click.9 To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing. Wear the lap belt snug against the hips. Sit back and erect in the seat, then adjust the belt as tightly as is comfortable.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlertT) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlertt) will alert the driver to buckle the seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Enhanced Warning System (BeltAlertt) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlertt) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • If your vehicle is equipped with window bags, do not stack luggage or other cargo up high enough to block the location of the window bag.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. 2. If your vehicle does not have a rear seat, see the Passenger Airbag ON/OFF Switch section. 1. Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. 6. If your vehicle has window bags, do not lean against the door or window, airbags will inflate forcefully into the space between you and the door. 7. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Driver and Front Passenger Seat Belt Pretensioners (if equipped) • Occupant Restraint Controller • Driver Seat Track Position Sensor (if equipped) • Side Remote Acceleration Sensors (if equipped) • Passenger Side Frontal Airbag ON/OFF Switch (2500/ 3500 Regular Cab Vehicles Only) • Airbag Warning Light • Driver Airbag • Passenger Airbag • Window Bags above Side Windows (if equipped)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. • Also, the ORC turns on the AIRBAG warning light in the instrument panel for six to eight seconds for a self-check when the ignition is first turned on.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ON/OFF switch (2500/3500 Regular Cab Vehicles Only). See Passenger Airbag ON/OFF Switch – (2500/ 3500 Regular Cab Vehicles Only) in this section for additional information. • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Side Impact SRS Window Bags are designed to activate only in certain side collisions. When the ORC (with side impact option) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the outside edge of the headliner out of the way and covers the window.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Airbag On/Off Switch – (2500/3500 Regular Cab Vehicles Only) because the infant has a medical condition which makes it necessary for the driver to be able to see the infant; • is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child; • has a medical condition
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! To Turn On the Passenger Airbag (2500/3500 Regular Cab Vehicles Only) Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. Place the ignition key in the Passenger Airbag ON/OFF Switch, push the key in and turn counterclockwise, and remove the key from the switch.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The light remains on or flickers after the six to eightsecond interval. after airbag deployment. EDR data are ONLY recorded if an airbag deploys and are otherwise unavailable. • The light flickers or comes on and remains on while driving. NOTE: Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Transmission gear selection • Cruise control status • Traction/stability control status • Tire pressure monitoring system (TPMS) status (if equipped) Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child: • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning-booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child restraint manufacturer’s directions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat cushion, and tether strap anchorages, located behind the seatback. (Refer to Child Restraint Tether Anchor later in this section.) 67 2 Identification dots are located above the standard cab front seat lower anchorages as a guide for locating lower anchors. NOTE: For children riding in the front seat of a Regular Cab model, refer to the “Passenger Airbag ON/OFF Switch” located in this section.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mega Cabt Rear Seats Child restraint systems having attachments designed to connect to the lower anchorages are now available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cabt model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating positions only. A child may be placed in the rear center seating position of a Quad Cabt model using the seat belt and child tether anchorage. Failure to follow this may result in serious or fatal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 WARNING! WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. An incorrectly anchored tether strap could lead to seat failure and injury to the child.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. Multiple Child Restraint Installation Sequence (Quad Cabt Rear Seats) 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat. 73 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufacturer’s instructions.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Tether Anchorage Points at All Three Seating Positions (Mega Cabt) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seatback under the head restraint to the tether anchor directly behind the seat. 2 2. Lift the cover, and attach the hook to the square opening in the sheet metal. 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Transporting Pets Airbags deploying in the front seat could harm your pet.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This is a normal part of the break-in and is not an indication of difficulty. CAUTION! • During the first 500 mi (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your axles, driveline and vehicle. • Limit your speed to 50 mph (80 km/h) during the first 500 mi (805 km) of towing.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a potentially toxic gas that, by itself, is colorless and odorless. To avoid inhaling these gases, the following precautions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Heater Defroster Ducts Inspect the heater defroster ducts for proper operation. Check for proper airflow through all defroster ducts. If there are any questions regarding the operation of your heater defroster ducts, have the system checked by an authorized dealer. Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under the vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected, the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 ▫ Inside Mirror . . . . . . . . . . . . . . . . . . . . . . . . .86 ▫ Automatic Dimming Mirror – If Equipped . . . .87 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .87 ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .88 ▫ Electronic Power Mirrors – If Equipped . . . . . .88 ▫ Electric Rear Window Defroster And Heated Sideview Mirrors – If Equipped . . . . . .
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . 131 ▫ 40-20-40 Front Seat . . . . . . . . . . . . . . . . . . . . 118 m To Open And Close The Hood . . . . . . . . . . . . . 133 ▫ Reclining Seats (1500 Regular And Quad Cabt Models) . . . . . 119 m Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Reclining Seats (2500/3500/Mega Cab Models) . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 m Windshield Wipers And Washers . . . . . . . . . . . . 141 m Overhead Console — If Equipped . . . . . . . . . . . 148 ▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . . 141 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . . . 149 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 142 m Overhead Console With Compass/Temperature Mini-Trip Computer — If Equipped . . . . . . . . . . 149 m Tilt Steering Column . . . . . . . . . . . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Automatic Compass Calibration . . . . . . . . . . . 154 m Power Sunroof — If Equipped . . . . . . . . . . . . . 163 ▫ Manual Compass Calibration . . . . . . . . . . . . . 154 ▫ Open Sunroof - Express Mode . . . . . . . . . . . . 164 ▫ Recalibrating The Compass . . . . . . . . . . . . . . 154 ▫ Closing Sunroof - Express . . . . . . . . . . . . . . . 164 ▫ Outside Temperature . . . . . . . . . . . . . . . . . . . 156 ▫ Pinch Protect Feature . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 m Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 ▫ Storage And Seats (Quad Cabt Models) . . . . . 176 ▫ Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic Transmission . . 169 ▫ Storage And Seats (Mega Cab Models) . . . . . . 177 ▫ Front Instrument Panel Cupholders (Bucket Seats) — Automatic Transmission . . . . . . . . . . . . . . 171 ▫ Front Instrument Panel Cupholders — Manual Transmission . . . . . . . . . . . . . . .
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror – If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. 87 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Electronic Power Mirrors – If Equipped Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror. Some vehicles will not have a convex right side mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirror Switches Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped out or in). A small blindspot mirror is integrated onto the main mirror surface. NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS-FREE COMMUNICATION (UConnectT) — IF EQUIPPED NOTE: The sales code RER, REN and REU radios contain an integrated Hands-Free Communication (UConnectt) system. Refer to your “Navigation User’s Manual” for UConnectt system operating instructions for these radios. UConnectt is a voice-activated, hands-free, in-vehicle communications system. UConnectt allows you to dial a phone number with your cellular phone using simple voice commands (e.g.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnectt phonebook enables you to store up to 32 names, with four numbers per name. Each language has a separate 32-name phonebook accessible only in that language. This system is driven through your Bluetootht “Hands-Free profile” cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnectt system is fully integrated with the vehicle’s audio system. The volume of the UConnectt system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnectt system such as 9CELL9 or caller ID on certain radios.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say 9Help9 following the beep. The UConnectt system will play all the options at any prompt if you ask for help. To activate the UConnectt system from idle, simply press the PHONE button and follow the audible prompts for directions. All UConnectt system sessions begin with a press of the PHONE button on the radio control head.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnectt system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority. You can pair up to seven cellular phones to your UConnectt system.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call by Saying a Name Add Names to Your UConnectt Phonebook • Press the PHONE button to begin. NOTE: Adding names to the phonebook is recommended when the vehicle is not in motion. • After the 9Ready9 prompt and the following beep, say “Call.9 • Press the PHONE button to begin. • The system will prompt you to say the name of the person you want to call. • After the 9Ready9 prompt and the following beep, say 9Phonebook New Entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnectt system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit Entries in the UConnectt Phonebook NOTE: Editing names in the phonebook is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Phonebook Edit.9 9Phonebook Edit9 can be used to add another phone number to a name entry that already exists in the phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE from which you choose. To select one of the entries from the list, press the “Voice Recognition” button while the UConnectt system is playing the desired entry and say 9Delete.9 • After you enter the name, the UConnectt system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnectt system will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the UConnectt system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnectt system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE to 9Toggling Between Calls9 in this section. To combine two calls, refer to 9Conference Call9 in this section. Place/Retrieve a Call From Hold To put a call on hold, press the PHONE button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the PHONE button until you hear a single beep.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Redial • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Redial.9 ends, or until the vehicle battery condition dictates cessation of the call on the UConnectt system and transfer of the call to the mobile phone. • The UConnectt system will call the last number that was dialed from your cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • After the 9Ready9 prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. If the phone is not reachable and the UConnectt system is operational, you may reach the emergency number as follows: • Continue to follow the system prompts to complete language selection. • Press the PHONE button to begin. After selecting one of the languages, all prompts and voice commands will be in that language.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UConnectt system to allow use of this vehicle feature in emergency situations, when the cell phone has network coverage and stays paired to the UConnectt system. Towing Assistance If you need towing assistance: • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Towing Assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnectt system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the “Voice Recognition” button and say the sequence you wish to enter, followed by the word 9Send.9 For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can press the “Voice Recognition” button and say, 93 7 4 6 # Send.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnectt system will not repeat a phone number before you dial it). • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Setup Confirmations.9 The UConnectt system will play the current confirmation prompt status and you will be given the choice to change it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mute/Un-Mute (Mute Off) When you mute the UConnectt system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnectt system: • Press the “Voice Recognition” button. • Following the beep, say 9Mute.9 In order to un-mute the UConnectt system: • Press the “Voice Recognition” button. • Following the beep, say 9Mute off.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say 9List Phones.9 • The UConnectt system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the “Voice Recognition” button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your UConnectT System UConnectt Tutorial To hear a brief tutorial of the system features, press the PHONE button and say “UConnectt Tutorial.” Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the UConnectt system Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the UConnectt mode (e.g.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say 9Send.9 • Make sure that no one other than you is speaking during a voice recognition period. • Storing names in the phonebook when the vehicle is not in motion is recommended.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • In a convertible vehicle, system performance may be compromised with the convertible top down. • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. Far End Audio Performance • In a convertible vehicle, system performance may be compromised with the convertible top down.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 3
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 115 3
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnectt Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. SEATS The seating options available in this truck are the result of extensive customer research and evaluations.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40-20-40 Front Seat Each outboard seat is independently adjustable forward or rearward and is equipped with a back recliner. The manual forward or rearward seat adjustment handle is found at the front edge of each seat cushion. Pull up on the handle and slide the seat to get the most comfortable position. WARNING! Manual Seat Adjuster As the name implies, the seat is divided into three segments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats (1500 Regular and Quad CabT Models) The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seatback and adjust for comfort. Seat Recliner Handle 119 WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats (2500/3500/Mega Cab Models) The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seatback and adjust for comfort. Seat Recliner Handle WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of neck injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears. 121 3 To lower the head restraint, push in the button and then push down on the head restraint.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback, and on the right side of the passenger’s seatback, increases or decreases the lumbar (lower back) support. Manual Lumbar Adjustment Power Seats (1500 Regular and Quad CabT Models) — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 switch can be moved up and down to control seat height, or to change the seat angle by tilting it up or down. 3 Power Seat Switch The power seat controls are on the outboard side of the front seat cushions. One switch controls the seat movement. The six-way switch can be moved forward or backward to get the most comfortable position.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats (2500/3500/Mega Cab Models) — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls or the Occupant Classification System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. 3 Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat movement. The four-way switch in the center can be moved forward or backward to get the most comfortable position.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Features — Mega Cab Models Reclining Rear Seats — Mega Cab Models The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seatback and adjust for comfort. Rear Seat Recliner Handle Folding Rear Seat (Table Mode) — Mega Cab Models Both the left and right rear seatbacks can be folded down and used as a table.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 3 Table Mode Handle Table Mode
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat (Kneel Mode) — Mega Cab Models Both the left and right rear seats can be folded flat (Kneel Mode) and used for carrying cargo. Each of the rear seatbacks provide two2 D-rings and each of the rear storage bin lids provide two slotted cutouts. Use a cargo tie-down to secure cargo in the cargo carrying area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Cargo must be securely tied down before driving your vehicle. Improperly secured cargo can fly around in a sudden stop and strike someone in the vehicle, causing serious injury or possible death.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To fold either rear seat flat (Kneel Mode), lift the handle and fold the seat forward. Simply lift the seatback to return the seat to the upright position. Verify that it is locked in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. 131 Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain High heat level, then press the switch again to obtain Low heat level. Pressing the switch a third time will turn the heated seats OFF. If you do not purposefully turn the switch OFF, the seat heating level will automatically change to the next lower level, or OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD 133 released you must reach into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. Hood Release Lever To open the hood, two latches must be released.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! LIGHTS If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the 9Party9 mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. If the ignition is OFF and any door is left ajar for 10 minutes or the dimmer control is rotated upwards for 10 minutes, the interior lights will automatically turn off. If the headlamps remain on while the ignition is cycled OFF, the exterior lights will automatically turn off after eight minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Light Switch Rotation Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-on Reminder If the headlights, parking lights, or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Fog Lights — If Equipped The fog lights are turned ON by placing the headlight rotary control in the parking light or headlight position and pushing in the headlight rotary control. The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Control Lever The multifunction control lever is located on the left side of the steering column. 139 You can signal a lane change by moving the lever partially up or down. Turn Signals Move the lever up or down to signal a right-hand or left-hand turn. 3 The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signal Auto Mode Tap the multifunction control lever once and the turn signal (left or right) will flash three times, and automatically turn off. Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. 141 Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction control lever and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, pull rearward on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever forward to lock the column firmly in place. Tilt Steering Control Lever 143 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF EQUIPPED Adjustment 1. Position the driver seat so that you are at least 10 in (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desire to move the pedals. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator operation at speeds greater than 25 mph (40 km/h). The controls are mounted on the steering wheel.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on. To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Tapping the RESUME ACCEL button once will result in a speed increase of 1 mph (2 km/h). Each time the button is tapped, speed increases so that tapping the button three times will increase speed by 3 mph (4.8 km/h). If the vehicle speed drops below 25 mph (40 km/h), the speed control will automatically disengage. If this happens, you can push down on the accelerator pedal to maintain the desired speed.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully-upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if equipped. These lights are also operated individually as reading lights by pressing the recessed area of the corresponding lens.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This overhead console allows you to choose between a compass/temperature display and one of four trip conditions being monitored. RESET Button US/M Button Use this button to change the display from U.S. to METRIC measurement units.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Global Reset If the RESET button is pressed twice within two seconds while in any of the three resettable displays (AVG ECO, ODO, ET), the Global Reset will reset all three displays. Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. Average fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled. Step Button When the fuel economy is reset, the display will momentarily blank.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. This is not resettable NOTE: It is possible for DTE to display “LO FUEL” before the low fuel warning light turns on in the instrument cluster.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Trip Odometer (ODO) 153 C/T Button NOTE: The maximum value is approximately 6000 mi (9956 km/h). Then the trip odometer must be reset in order to update the trip odometer miles/kilometers. 3 This display shows the distance traveled since the last reset. Resetting of this screen will cause the trip odometer to change to zero. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Even if the display still reads a few degrees above 32° F ( 0° C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the CAL symbol will be displayed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 3 Reset Button Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The default for the compass variance is zone 8. To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 WARNING! HomeLink Buttons NOTE: HomeLinkt is disabled when the Vehicle Theft Alarm is active. Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If you have not trained any of the HomeLinkt buttons, erase all channels before you begin training. Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. To do this, press and hold the two outside buttons for 20 seconds. Release the buttons when the indicators start to flash.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE For optimal training, point the battery end of the handheld transmitter away from the HomeLinkt. 3. Simultaneously, press and hold both the chosen HomeLinktbutton and the hand-held transmitter button until the indicator(s) change from a slow to a rapid flash rate. Then release both the HomeLinkt and hand-held transmitter buttons. It may take up to 30 seconds, or longer in rare cases. The garage door may open & close while you train.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “learn” or “training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open & close the door). 1 — Garage Door Opener 2 — Training Button 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Return to the vehicle and press the programmed HomeLinkt button twice (holding the button for 2 seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for 2 seconds) to complete the training. If you are have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then proceed with Step 4 under, “Programming HomeLinkt,” earlier in this section. Using HomeLinkT To operate, simply press and release the programmed HomeLinkt button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.) The hand-held transmitter of the device may also be used at any time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the “Learn” button on the Garage Door Opener to complete the training for Rolling Code. • Did you unplug the device for training, and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com, for information or assistance. General Information This device complies with FCC rules part 15 and Industry Canada RSS-210.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The outlet(s) has/have a fused direct feed from the battery so it/they receive power whether the ignition is ON or OFF. All accessories connected to this/these outlet(s) should be removed or turned OFF when the vehicle is not in use to protect the battery against discharge. NOTE: If desired, all of the power outlets can be converted by your authorized dealer to provide power with the ignition switch in the ON position only.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER The removable ash receiver is located in the instrument panel cupholder tray. The cigar lighter is located on the instrument panel, above and to the left of the ash receiver. As a child safety precaution, the lighter only operates with the ignition switch ON. It heats when pushed in and pops out automatically when ready for use. To preserve the heating element, do not hold the lighter in the heating position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic Transmission Your new vehicle is equipped with two adjustable cupholders. The cupholder is opened by pulling on the cup holder door handle located on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cupholder Door Handle Cupholders Automatic Transmission
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders (Bucket Seats) — Automatic Transmission If your new vehicle is equipped with bucket seats there are three cupholders located on the front of the center console.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholder (Quad CabT) — If Equipped Quad Cabt vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger convenience. Rear Cupholder (Mega CabT) Mega Cabt vehicles are equipped with rear cupholders located in the center armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Center Storage Compartment (40–20–40 Seat) – If Equipped 173 cover. Inside there is a power outlet (if equipped), removable coin holder (if equipped), and two dividers to configure the storage area into compartments. For example, compartments can be configured to hold a lap-top computer, a cellular telephone, CDs and miscellaneous items. The top of the cover provides a generous firm surface to serve as a desktop for your “mobile office.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Center Storage Compartment (Bucket Seats) – If Equipped • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE storage area into separate compartments. Lift the lower handle on the front of the armrest, and raise the armrest for access to the lower storage bin. On Quad Cabt and Mega Cabt models the rear of the floor console offers a power outlet, and a tip out bin. WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Quad CabT Models) Located in the center of the front 40–20–40 seat cushion there is a storage compartment. Regular Cab models also have storage behind the seat. The Quad Cabt models provide additional storage under the rear seat. Lift the seat to access the storage compartment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Storage and Seats (Mega Cab Models) The Mega Cab models provide additional storage behind the rear seat. To gain access to the Mega Cab rear storage, fold the rear seats to the “kneel position”. (See page 128 for more information.) 3 Push down on the front of the storage compartment handle and lift the storage compartment cover.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear storage compartment can be divided into three separate compartments by using the divider doors inside the storage compartment. Plastic Grocery Bag Retainers (Mega Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cabt models with a 60/40 rear seat may be equipped with a folding load floor. Quad Cabt Rear 60/40 Seat 179 WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. Unfolding The Load Floor 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Load Floor In Open Position 3. Reverse the procedure to store the load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3 3. Lift the load floor up to access storage under the load floor. WARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury. Load Floor Securing Straps 4.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Power Sliding Rear Window — If Equipped Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated Sideview Mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition ON. Turning OFF the ignition will deactivate the Electric Rear Window Defroster and Heated Sideview Mirrors feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sliding Rear Window — If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. 183 PICKUP BOX 3 Pickup Box Features The pickup box on your new vehicle has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopart toolbox brackets available from your authorized dealer.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can carry wide building materials (sheets of plywood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor. WARNING! The pickup box is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. WARNING! • Care should always be exercised when operating a vehicle with unrestrained cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box. There are four tie-down cleats bolted to the lower sides of the pickup box that can sustain loads up to 1000 lbs (450 kg) total. SLIDE-IN CAMPERS Camper Applications Certain truck models are not recommended for slide-in campers.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Dual rear wheel pickup models require properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . . 193 ▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 210 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 194 m Sales Code REF — AM/FM/CD (Single-Disc) Radio With Optional Satellite Radio And Hands-Free Phone Capability . . . . . . . . . . . . . . 211 ▫ Premium Cluster – If Equipped . . . . . . . . . . . 194 ▫ Base Cluster – If Equipped . . . . . . . . . . . . . . .
190 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions - Satellite Radio — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 218 m Sales Code RAQ – AM/FM/CD (6-Disc) Radio With Optional Satellite Radio, Hands-Free Phone, And Video Entertainment System (VES™) Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 ▫ Operating Instructions - Radio Mode . . . . . . . 219 ▫ Operating Instructions (CD Mode For CD Audio Play) . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Noise Reduction . . . . . . . . . . . . . . . . . . . . . . 239 ▫ Operating Instructions (CD Mode For CD Audio Play) . . . . . . . . . . . 240 ▫ Load/Eject Button (CD Mode For CD Audio Play) . . . . . . . . . . . 241 191 m Video Entertainment System (Sales Code XRV) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 m Satellite Radio — If Equipped . . . . . . . . . . . . . . 251 ▫ System Activation . . . . . . . . . . . . . . . . . . . . .
192 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 254 m Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 259 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 255 ▫ Heater Only — If Equipped . . . . . . . . . . . . . . 259 m Remote Sound System Controls — If Equipped . . 255 ▫ Air Conditioning And Heating — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Radio Operation . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 193 INSTRUMENTS AND CONTROLS 4 1 2 3 4 5 — Headlight Switch — Air Outlets — Instrument Cluster — Climate Controls — Radio 6 — Passenger Airbag 7 — Glove Box 8 — Passenger Airbag On/Off Switch* 9 — Power Outlet 10 — Heated Seat Switch 11 — TPMS “Light Load” Reset Switch* 12 — Power Sliding Back Glass Switch* 13 — Cupholders 14 — ESP Off Switch* 15 — Cigar Lighter 16 — Transfer Case Control Switch* 17 — Parking Brake Release Lever 18 — Adjustable Pedal Control Switc
194 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Premium Cluster – If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Base Cluster – If Equipped 4
196 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Check Gauges – Premium Cluster Only This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gauges indicate a reading either too high or too low. Examine the gauges carefully, and follow the instructions contained below for each indicated problem.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 5. Airbag Indicator Light The indicator lights and remains lit for six to eight seconds when the ignition is first turned ON. If the light stays on, flickers or comes on while driving, have the airbag system checked by an authorized dealer. 6. High Beam Indicator This indicator shows that headlights are on high beam. 7.
198 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gauges” indicator will illuminate and a single chime will sound. 10. Transfer Case Position This display indicator shows the transfer case position selection. For additional information refer to “4-Wheel Drive Operation” in section 5 of this manual. 11. TOW HAUL The TOW HAUL button is located at the end of the gear shift lever.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not leave your vehicle unattended with the engine running as you would not be able to react to the temperature indicator if the engine overheats. NOTE: Engine idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling. NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gauges” indicator will illuminate and a single chime will sound. 14.
200 UNDERSTANDING YOUR INSTRUMENT PANEL To reset a trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately two seconds).
UNDERSTANDING YOUR INSTRUMENT PANEL release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the following procedure. 1. Turn the ignition switch to the ON position (Do not start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position.
202 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. 19. Brake System Warning Light This light illuminates when the ignition key is turned to the ON position and remains on for a few seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL that the anti-lock portion of the brake system is not functioning and that service is required. See your authorized dealer immediately. The ABS light could also illuminate during loss of traction and remain illuminated until the brake pedal is pressed. 21. Electronic Throttle Control (ETC) This light informs you of a problem with the Electronic Throttle Control system. If a problem is detected the light will come on while the engine is running.
204 UNDERSTANDING YOUR INSTRUMENT PANEL 24. ESP/BAS Warning Lamp – If Equipped The lamp indicates a problem with one or more of the functions of ESP. The yellow “ESP/BAS Warning Lamp” in the instrument cluster comes on when the ignition switch is turned to the ON position as a bulb check. It should go out with the engine running. If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in the ESP system.
UNDERSTANDING YOUR INSTRUMENT PANEL can lead to tire failure. Under inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
206 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
UNDERSTANDING YOUR INSTRUMENT PANEL 27. Transmission Oil Temperature Warning Light (Automatic Transmissions Only) This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.g., snow plowing, off- road operation).
208 UNDERSTANDING YOUR INSTRUMENT PANEL 31. CRUISE Light This indicator lights when the electronic speed control system is turned on. NOTE: Engine idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling. 32. Coolant Temperature Light – Base Cluster Only This light indicates engine coolant temperature is to high. If the light comes on, stop the vehicle, shift into NEUTRAL, and increase the engine idle speed for two to three minutes.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the frequency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the ON or ACC position. When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained.
210 UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REF — AM/FM/CD (SINGLE-DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS-FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. 211 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
212 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button (Radio Mode) Press the MODE button repeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO control. 3. After the hours are adjusted, press the TUNE/AUDIO control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the TUNE/AUDIO control. 5. To exit, press any button/knob or wait five seconds.
214 UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory. Press the rotary TUNE control a fifth time and FADE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display. If the volume control is ON, the unit will switch to CD mode and begin to play.
216 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Operating Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. 9MUTE9 will display.
218 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Operating Instructions - Hands-Free Phone — If Equipped Refer to the “Hands-Free Phone (UConnectt)” section of this Owner’s Manual. RW/FF (Auxiliary Mode) No function. Operating Instructions - Satellite Radio — If Equipped Refer to the “Satellite Radio” section of this Owner’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS-FREE PHONE, AND VIDEO ENTERTAINMENT SYSTEM (VES™) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. 219 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
220 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button (Radio Mode) Press the MODE button repeatedly to select between the CD player, Satellite Radio, or Video Entertainment System (VES)™ (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selection.
UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button Press the TIME button and the time of day will be displayed for five seconds. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO control. 3. After the hours are adjusted, press the TUNE/AUDIO control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes by turning the TUNE/AUDIO control. 5. To exit, press any button/knob or wait five seconds.
222 UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BALANCE will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues 16 Digit-Character Display Foreign_Language Information Jazz News Nostalgia Oldies Personality Public Rhythm_and_Blues Religious_Music Religious_Talk Rock Soft Soft_Rock Soft_R_&_B Program Type Sports Talk Top 40 Weather 223 16 Digit-Character Display Sports Talk Top_40 Weather By pressing t
224 UNDERSTANDING YOUR INSTRUMENT PANEL SET/DIR Button (Radio Mode) — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/DIR button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display. CAUTION! This CD player will accept 4 3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF.
226 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD Mode for CD Audio Play) Press the SCAN button to scan through each track on the CD currently playing. LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/ EJECT - Load Press the LOAD/EJECT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays 9LOAD DISC9 insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 display 9INSERT DISC” for 10 seconds. If no discs are inserted within 10 seconds “NO DISCS LOADED” will be displayed. TUNE Control (CD Mode for CD Audio Play) Pressing the TUNE control allows the setting of the Tone, Fade, and Balance. See Radio Mode. On some vehicles a disc can be ejected with the radio and ignition OFF. AM/FM Button (CD Mode for CD Audio Play) Switches the Radio to the Radio mode.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. The radio uses the following limits for file systems: Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL LOAD/EJECT - Eject Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show 9EJECTING DISC9 when the disc is being ejected and prompt the user to remove the disc. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
232 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAK – AM/FM/CASSETTE/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, VIDEO, MP3, and WMA CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. 233 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
234 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (Radio Mode) Press and release the SEEK button to search for the next station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remained tuned to the new station until you make another selection. Holding the button and will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM modes.
236 UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Radio Mode) Pressing this button once will turn on the PTY mode for five seconds. If no action is taken during the five-second time out, the PTY icon will turn off. Turning the tune knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Public College Unassigned Weather 237 16 Digit-Character Display Public College Buttons 1 - 6 (Radio Mode) These buttons tune the Radio to the stations that you commit to push-button memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. Weather Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the left and the mechanical action of the player will gently pull the cassette into the play position.
238 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward one to six selections. Press the SEEK button once to move one selection, twice to move two selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
UNDERSTANDING YOUR INSTRUMENT PANEL Changing Tape Direction If you wish to change the direction of tape travel (side being played), press Preset 6. The lighted arrow in the display window will show the new direction. Metal Tape Selection If a standard metal tape is inserted into the player, the player will automatically select the correct equalization.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - (CD Mode for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks and WMA. Inserting Compact Disc(s) CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 LOAD/EJECT Button (CD Mode for CD Audio Play) Radio display will show 9EJECTING DISC9 when the disc is being ejected and prompt the user to remove the disc. LOAD/EJECT - Load Press the LOAD/EJT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays 9INSERT DISC,9 insert the CD into the player.
242 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD Mode for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature. If the RW button is pressed, the current track will reverse to the beginning of the track and begin playing.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. The radio uses the following limits for file systems: Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R, and CD-RW.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 and WMA Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
246 UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will show 9LOADING DISC9 when the disc is loading. LOAD/EJT - Eject Press the LOAD/EJT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show 9EJECTING DISC9 when the disc is being ejected and prompt the user to remove the disc. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder.
248 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America. Refer to your “Navigation User’s Manual” for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL the worldwide standard for time. This makes the system’s clock very accurate once the appropriate time zone and daylight savings information is set. 1. At the Main Menu screen, highlight “Clock Setup” and press ENTER OR press and hold for three seconds the TIME button on the unit’s faceplate. The Clock Setup screen appears. 249 2. To show the GPS clock, select “Displayed Clock: GPS Clock” and press ENTER. 3. To adjust the time zone, Select “Time Zone” and press ENTER.
250 UNDERSTANDING YOUR INSTRUMENT PANEL User Defined Clock If you wish to set the clock to a time different than the system clock, you can manually adjust the time by choosing the “User Defined Clock” option. 1. At the Clock Setup screen highlight “Displayed Clock: User Defined Clock”. 2. To increase the clock by hours, make sure “HR +” is highlighted and press ENTER. Press ENTER again to increase the clock by another hour.
UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional Video Entertainment System™ (VES™) consists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two headsets. The system is located in the headliner behind the front row seat. Refer to your VES™ User’s Manual for detailed operating instructions.
252 UNDERSTANDING YOUR INSTRUMENT PANEL To access the ESN/SID, refer to the following procedure. ESN/SID Access with REF Radios With the ignition switch in the ACC position and the radio OFF, press the CD Eject and TIME buttons simultaneously for three seconds. The first four digits of the 12-digit ESN/SID number will display. Press the SEEK UP button to display the next four digits. Continue to press the SEEK UP button until all 12 ESN/SID digits display.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Selecting Satellite Mode — RAQ and RAK Radio Press the MODE button repeatedly until the word 9SAT9 appears in the display. before moving on to the next channel. The word 9SCAN9 will appear in the display between each channel change. Press the SCAN button a second time to stop the search. These radios will also display the current station name and program type. For more information, such as song title and artist, press the MSG or INFO button.
254 UNDERSTANDING YOUR INSTRUMENT PANEL Using The PTY (Program Type) Button — If Equipped Follow the PTY button instructions that apply to your radio. PTY Button SEEK When the desired program is obtained, press the SEEK button within five seconds. The channel will change to the next channel that matches the program type selected. PTY Button SCAN When the desired program type is obtained, press the SCAN button within five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception. 4 • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.
256 UNDERSTANDING YOUR INSTRUMENT PANEL The left-hand control is a rocker type switch with a push button in the center. The function of the left-hand control is different, depending on which mode you are in. The following describes the left-hand control operation in each mode. Radio Operation Pressing the top of the left side switch will seek up for the next listenable station and pressing the bottom of the switch will seek down for the next listenable station.
UNDERSTANDING YOUR INSTRUMENT PANEL CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2. Keep the cassette tape in its case to protect from slackness and dust when it is not in use. 3. Keep the cassette tape away from direct sunlight, heat and magnetic fields such as the radio speakers. 4.
258 UNDERSTANDING YOUR INSTRUMENT PANEL COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions.
260 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots. Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Panel Outside air flows through the outlets located in the instrument panel. Outside air flows in equal proportions through the floor and defroster outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control 261 Air Conditioning and Heating — If Equipped The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left position. Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy.
UNDERSTANDING YOUR INSTRUMENT PANEL Floor 263 Blower Control Outside air flows primarily through the floor outlets located under the instrument panel. Mix Outside air flows in equal proportions through the floor and defroster outlets, and the air conditioning may be on.
264 UNDERSTANDING YOUR INSTRUMENT PANEL Circulation The cab is designed with features to promote outside air circulation. There are grilles in the cab back panel. These are air exhausters that provide the means for regular exchange of cab air. Side window demisters direct airflow specifically to the window glass to help prevent interior fogging of the glass. They are located in the extreme outside upper edges of the instrument panel. The demisters also provide extra air ducts for circulation.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning and Heating Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be directed through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off.
266 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots and give an even blend of both modes. Panel Outside air flows through the outlets located in the instrument panel. These outlets can be adjusted to direct the airflow. Bi-Level Air flows through the outlets located in the instrument panel and those located on the floor.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control 267 Dual Zone Temperature Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left position. 4 Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Circulation The cab is designed with features to promote outside air circulation. There are grilles in the cab back panel. These are air exhausters that provide the means for regular exchange of cab air. Side window demisters direct airflow specifically to the window glass to help prevent interior fogging of the glass. They are located in the extreme outside upper edges of the instrument panel. The demisters also provide extra air ducts for circulation.
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases turning on the air conditioning (pressing the snowflake button) will clear the fog. Adjust the temperature control, air direction and blower speed to maintain comfort. As the temperature gets colder it may be necessary to direct air onto the windshield by using MIX Mode position on the control.
270 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: On models equipped with Diesel engines, the idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling. Your air conditioning system is also equipped with an automatic recirculation system. When the system senses a heavy load or high heat conditions, it may use partial Recirculation A/C mode to provide additional comfort.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Operating Tips Chart 4
STARTING AND OPERATING CONTENTS m Starting Procedures – Gas Engines . . . . . . . . . . . 278 m Manual Transmission . . . . . . . . . . . . . . . . . . . . 288 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Shifting — 2500/3500 Models . . . . . . . . . . . . . 289 ▫ Automatic Transmission – If Equipped . . . . . . 279 ▫ Shifting — 1500 Vehicles . . . . . . . . . . . . . . . . 291 ▫ Manual Transmission – If Equipped . . . . . . . . 279 ▫ Downshifting – All Manual Transmissions . .
274 STARTING AND OPERATING ▫ Transfer Case Reminder Light . . . . . . . . . . . . 298 m Driving Off-Road . . . . . . . . . . . . . . . . . . . . . . . 317 ▫ Electronically Shifted Transfer Case Operating Information/Precautions (5 Position Switch) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 298 m Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 318 ▫ Shifting Procedure — Electronically Shifted Transfer Case . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Traction Control System (TCS) . . . . . . . . . . . . 326 ▫ BAS (Brake Assist System) . . . . . . . . . . . . . . . 326 ▫ HSA (Hill Start Assist) . . . . . . . . . . . . . . . . . . 328 ▫ Electronic Roll Mitigation (ERM) . . . . . . . . . . 332 ▫ ESP (Electronic Stability Program) . . . . . . . . . 333 ▫ TSC (Trailer Sway Control) . . . . . . . . . . . . . . 337 m Multi-Displacement System (MDS) — 5.7L Engine Only . . . . . . . . . . . . . . . . . . . . . . .
276 STARTING AND OPERATING m Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 371 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . . 372 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 373 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 373 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 374 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 374 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 375 m Adding Fuel . . . . . . . . . . . . . . . .
STARTING AND OPERATING 277 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 398 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 404 ▫ Trailer Towing Mirrors — If Equipped . . . . . . 400 ▫ General Maintenance . . . . . . . . . . . . . . . . . . . 405 m Snowplow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 m Recreational Towing (Behind Motorhome, Etc.) . . 406 ▫ 1500 Models (Light Duty) . . . . . . . . . . . . . . .
278 STARTING AND OPERATING STARTING PROCEDURES – GAS ENGINES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! Be sure to turn off the engine and remove the key from the ignition switch if you want to rest or sleep in your vehicle.
STARTING AND OPERATING 279 Automatic Transmission – If Equipped Start the engine with the shift lever in the NEUTRAL or PARK position. Apply the brake before shifting to any driving range. NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of PARK. Tip Start Feature – Automatic Transmission Only Do not press the accelerator. Turn the ignition key briefly to START position, and release it.
280 STARTING AND OPERATING If Engine Fails To Start If the engine fails to start after you have followed the normal starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly.
282 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver side of the vehicle. It has a removable cap that is located on the driver’s side of the Integrated Power Module.
STARTING AND OPERATING WARNING! It is dangerous to shift the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
284 STARTING AND OPERATING WARNING! WARNING! Never use PARK position on an automatic transmission as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. It is dangerous to shift the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
STARTING AND OPERATING 285 NEUTRAL Shift to Neutral when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. FIRST Use this position for driving up very steep hills and for engine braking at low speeds 20 mph (32 km/h) or less when going downhill. To prevent excessive engine speed, do not exceed 25 mph (40 km/h) in this range.
286 STARTING AND OPERATING • the engine coolant has reached normal operating temperature; • vehicle speed is above approximately 30 mph (48 km/h); • the “TOW HAUL O/D OFF” switch has not been activated; • transmission has reached normal operating temperature. NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature.
STARTING AND OPERATING When To Use “TOW HAUL” and “O/D OFF” Modes Tow Haul O/D Off Switch When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the “TOW HAUL O/D OFF” button once to select TOW HAUL. This will improve performance and 287 reduce the potential for transmission overheating or failure due to excessive shifting.
288 STARTING AND OPERATING Torque Converter Clutch A feature, designed to improve fuel economy, has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly different feeling or response during normal operation in the upper gears. When the vehicle speed drops or during acceleration when the transmission downshifts to second gear, the clutch automatically disengages.
STARTING AND OPERATING CAUTION! 289 Shifting — 2500/3500 Models Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. NOTE: During cold weather, you may experience increased effort in shifting until the transmission fluid warms up. This is normal. 5 Shift Pattern Truck models with manual transmission are equipped with a clutch interlocking ignition system.
290 STARTING AND OPERATING Fully depress the clutch pedal before shifting gears. As you release the clutch pedal, lightly depress the accelerator pedal. 2500 and 3500 models are equipped with the G56 manual transmission. This transmission has a “creeper” 1st gear which should be used to start from a standing position when carrying a payload or towing a trailer. Damage to the clutch can result from starting in 2nd or 3rd gear with a loaded vehicle. An unloaded vehicle may be launched in 2nd gear.
STARTING AND OPERATING Shifting — 1500 Vehicles 291 Fully depress the clutch pedal before shifting gears. As you release the clutch pedal, lightly depress the accelerator pedal. You should always use 1st gear when starting from a standing position. Recommended Shift Speeds To utilize your manual transmission efficiently for both fuel economy and performance, it should be upshifted as listed in recommended shift speed chart. Shift at the vehicle speeds listed for acceleration.
292 STARTING AND OPERATING Higher upshift speeds may be used to obtain a desired acceleration rate. 6 Speed Manual Transmission Shift Speed in mph (km/h) AccelEn1 to 2 to 3 to 4 to 5 to Model Axle eration gine 2 3 4 5 6 Rate 15 24 34 47 56 ACCEL (24) (39) (55) (76) (90) 3.7L ALL ALL & 10 19 27 37 41 CRUISE (16) (31) (44) (60) (66) ACCEL 15 25 40 45 50 4.
STARTING AND OPERATING CAUTION! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage, and/or clutch disc damage even if the clutch pedal is depressed. Maximum Recommended Downshift Speeds CAUTION! Failure to follow the recommended downshifting speeds may cause the engine to overspeed and/or damage the clutch disc even if the clutch pedal is depressed.
294 STARTING AND OPERATING The “knock-over” prevents the driver from accidentally entering the REVERSE (R) shift area and warns the driver that they are about to shift the transmission into REVERSE (R). Due to this feature, a slow shift to REVERSE (R) can be perceived as a high shift effort. Manually Shifted Transfer Case Operating Information/Precautions The transfer case provides 4 mode positions - 2 (rear)wheel drive high range, 4-wheel drive high range, neutral, and 4-wheel drive low range.
STARTING AND OPERATING 295 The 4-wheel drive light (4WD), located in the instrument cluster, alerts the driver that the vehicle is in 4-wheel drive and that the front and rear driveshafts are locked together. This light illuminates when the transfer case is shifted to either the 4H or 4L positions. There is no light for the 2H or NEUTRAL positions. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning.
296 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING Shifting Procedure - Manually Shifted Transfer Case 297 vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelerator pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to NEUTRAL or depress the clutch on a manual transmission.
298 STARTING AND OPERATING NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may occur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The preferred method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4L with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h).
STARTING AND OPERATING This Electronically Shifted transfer case provides 5 mode positions: 2-wheel drive (2WD), 4WD AUTO, 4WD LOCK, NEUTRAL and 4WD LOW. The Electronically Shifted transfer case is designed to be driven in the 2 wheel drive position (2WD) or 4-wheel drive position (4WD AUTO) for normal street and highway conditions (dry hard surfaced roads). Driving the vehicle in 2WD will have greater fuel economy benefits, as the front axle is not engaged in 2WD.
300 STARTING AND OPERATING Transfer Case Position Indicator Lights — Electronically Shifted Transfer Case Only Transfer case position indicator lights are located on the instrument cluster and indicate the current and desired transfer case selection. When you select a different transfer case position, the indicator lights will do the following: If All Shift Conditions are Met 1. The current position indicator light will turn OFF.
STARTING AND OPERATING If One or More Shift Conditions are not Met 1. The indicator light for the current position will remain ON. 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection.
302 STARTING AND OPERATING When operating your vehicle in 4WD LO, the engine speed is approximately three times that of the 2WD, 4WD AUTO or 4WD HI positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case.
STARTING AND OPERATING For additional information on the appropriate use of each transfer case mode position see the information below: 2WD Rear-Wheel Drive High Range - Normal street and highway driving. Dry hard surfaced roads. 4WD AUTO Automatic 4–wheel drive sends power to the rear wheels. 4–wheel drive will be automatically engaged when the vehicle senses a loss of traction. Additional traction for varying road conditions.
304 STARTING AND OPERATING Shifting Procedure — Electronically Shifted Transfer Case light will continue to flash until all the requirements for the selected position have been met. To retry a shift: return the control knob back to the original position, make certain all shift requirements have been met, wait five (5) seconds and try the shift again.
STARTING AND OPERATING stopped, the ignition key must be in the ON position with the engine either RUNNING or OFF. This shift cannot be completed if the key is in the accessory position. 2WD or 4 AUTO or 4 LOCK ⇔ 4WD LOW NOTE: When shifting into or out of 4WD LOW some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants. Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped.
306 STARTING AND OPERATING 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions).
STARTING AND OPERATING 307 This Electronically Shifted transfer case provides four mode positions: 2 (rear)-wheel drive high range, 4-wheel drive lock range, 4-wheel drive low range, and NEUTRAL. The Electronically Shifted transfer case is designed to be driven in the 2-wheel drive position (2WD) for normal street and highway conditions (dry, hard surfaced roads).
308 STARTING AND OPERATING Transfer Case Position Indicator Lights — Electronically Shifted Transfer Case Only Transfer case position indicator lights are located in the instrument cluster and indicate the current and desired transfer case selection. When you select a different transfer case position, the indicator lights will do the following: If All Shift Conditions Are Met: 1. The current position indicator light will turn OFF. 2.
STARTING AND OPERATING WARNING! Always engage the parking brake when powering down the vehicle if the (SERVICE 4WD( light is illuminated. Not engaging the parking brake may allow the vehicle to roll, which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning, as this can cause damage to driveline components.
310 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING Shifting Procedure — Electronically Shifted Transfer Case 311 light will continue to flash until all the requirements for the selected position have been met. To retry a shift: return the control knob back to the original position, make certain all shift requirements have been met, wait five seconds and try the shift again.
312 STARTING AND OPERATING ignition key must be in the ON position with the engine either running or off. This shift cannot be completed if the key is in the ACC position. Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. USE EITHER OF THE FOLLOWING PROCEDURES: NOTE: The 4x4 system will not allow shifts between 2WD/4WD LOCK if the front and/or rear wheels are spinning (no traction).
STARTING AND OPERATING Alternate Procedure 1. Bring the vehicle to complete stop. 2. With the key ON and the engine either OFF or running, shift the transmission into NEUTRAL (depress clutch on manual transmissions). 3. Rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions).
314 STARTING AND OPERATING slippery surface, a slight application of the accelerator will supply maximum traction. When starting with only one rear wheel on an excessively slippery surface, slight momentary application of the parking brake may be necessary to gain maximum traction. WARNING! On vehicles equipped with a limited-slip differential, never run the engine with one rear wheel off the ground, since the vehicle may drive through the rear wheel remaining on the ground.
STARTING AND OPERATING DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly.
316 STARTING AND OPERATING CAUTION! WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING DRIVING OFF-ROAD Care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope. If natural obstacles force you to travel diagonally up or down a hill, choose a mild angle and keep as little side tilt as possible. Keep the vehicle moving and make turns slowly and cautiously. If you must back down a hill, back straight down using REVERSE gear. Never back down in NEUTRAL, or diagonally across the hill.
318 STARTING AND OPERATING PARKING BRAKE The foot-operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or FIRST gear. Failure to do so may allow the vehicle to roll and cause damage or injury. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
320 STARTING AND OPERATING 3500 Dual Rear Wheel Models Only The brake system power assist is provided by a hydroboost unit which shares fluid with the power steering system. You may experience some clicking or hissing noises from the hydro-boost system during hard braking conditions. NOTE: Under cold temperatures, pedal effort will be higher than normal until the power steering fluid reaches operating temperature.
STARTING AND OPERATING WARNING! Both Rear-Wheel and Four-Wheel Anti-Lock Brake Systems contain sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
322 STARTING AND OPERATING When you are in a severe braking condition involving use of the ABS, you will experience some pedal drop as the vehicle comes to a complete stop. This is the result of the system reverting to the base brake system and is normal. Engagement of the ABS may be accompanied by a pulsing sensation. You may also hear a clicking noise. These occurrences are normal, and indicate that the system is functioning. ABS Warning Light The ABS includes an amber warning light.
STARTING AND OPERATING WARNING! • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
324 STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible. Damage to the power steering pump may occur.
STARTING AND OPERATING ABS (Anti-Lock Brake System) This ABS system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lockup and help avoid skidding on slippery surfaces during braking. For more information about ABS, refer to “Anti-Lock Brake System” under “Brake System” in Section 5 of this manual. NOTE: ABS improves steering control of the vehicle during hard braking maneuvers.
326 STARTING AND OPERATING Traction Control System (TCS) The TCS system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s), and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited-slip differential and controls the wheel spin across a driven axle.
STARTING AND OPERATING applies optimum pressure to the brakes in emergency braking conditions. This can help reduce braking distances. The BAS complements the ABS. Applying the brakes very quickly results in the best BAS assistance. To receive the benefit of BAS, you must apply continuous braking pressure during the stopping sequence. Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated.
328 STARTING AND OPERATING HSA (Hill Start Assist) The HSA system is designed to assist the driver in launching a vehicle on an incline. HSA will maintain the level of brake pressure the driver inputs for a short duration once the driver takes his foot off of the brake pedal. If the driver does not apply the throttle during this short duration, the system will release brake pressure and the vehicle will roll down the incline.
STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backing uphill is in REVERSE gear). WARNING! There may be situations on minor hills (i.e., less than 7%), with a loaded vehicle, or while pulling a trailer where the system will not activate and slight rolling may occur, which could cause a collision with another vehicle or object. Always remember the driver is responsible for braking the vehicle.
330 STARTING AND OPERATING Towing and Hauling with HSA (Vehicles Equipped with Automatic Transmissions Only) The HSA system does not know if your vehicle is loaded or towing a trailer, unless the TOW/HAUL button, located on the transmission gear shift lever, is selected. When activated, the TOW/HAUL light will illuminate in the instrument cluster. For more information on TOW/ HAUL mode, refer to “When To USE TOW/HAUL and O/D OFF Modes” under 9Automatic Transmission” in Section 5.
STARTING AND OPERATING WARNING! HSA is not a parking brake. If you stop the vehicle on a hill without putting the transmission in PARK or using the parking brake, it will roll down the incline and could cause a collision with another vehicle or object. Always remember to use the parking brake while parking on a hill, and that the driver is responsible for braking the vehicle. HSA Off If you wish to turn off the HSA system, follow this procedure: 1.
332 STARTING AND OPERATING Electronic Roll Mitigation (ERM) The ERM system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When ERM determines that the rate of change of the steering wheel angle and vehicle speed are sufficient to potentially cause wheel lift, it applies the appropriate brake and may reduce engine power to lessen the chance that wheel lift will occur.
STARTING AND OPERATING ESP (Electronic Stability Program) The ESP system enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
334 STARTING AND OPERATING WARNING! • ESP (Electronic Stability Program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING ESP Partial Off This mode is entered by momentarily depressing the 9ESP OFF” switch. When in 9Partial Off9 mode, the TCS portion of ESP, except for the “limited slip” feature described in the TCS section, has been disabled and the 9ESP/TCS Indicator Light9 will be illuminated. All other stability features of ESP function normally.
336 STARTING AND OPERATING holding the “ESP Control Switch” for five seconds when the vehicle is stopped and the engine is running. After five seconds, the “ESP/TCS Indicator Light” will illuminate and the “ESP Off” message will appear in the odometer. Press and release the trip odometer button located on the instrument cluster to clear this message. driving but ESP function returns to provide the stability feature at speeds above 40 mph (64 km/h).
STARTING AND OPERATING ESP/BAS Warning Lamp and ESP/TCS Indicator Light The malfunction indicator for the ESP is combined with the BAS indicator. The yellow “ESP/BAS Warning Lamp” and the yellow “ESP/TCS Indicator Light” in the instrument cluster both come on when the ignition switch is turned to the ON position. They should both go out with the engine running.
338 STARTING AND OPERATING information on towing a trailer with your vehicle. When TSC is functioning, the “ESP/TCS Indicator Light” will flash, the engine power may be reduced and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying. TSC is disabled when the ESP system is in the Partial Off or Full Off modes. If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway.
STARTING AND OPERATING TIRE SAFETY INFORMATION TIRE MARKINGS 339 • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H. • LT (Light Truck) - Metric tire sizing is based on U.S. design standards.
340 STARTING AND OPERATING Tire Sizing Chart TIRE SIZING TERMS Size Designation: P = Passenger Car tire size based on U.S. design standards (....blank....( = Passenger Car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 341 TIRE SIZING TERMS Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
342 STARTING AND OPERATING TIRE IDENTIFICATION NUMBER (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 343 TIRE IDENTIFICATION NUMBER EXAMPLE: DOT MA L9 ABCD 0301 — Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991 TIRE LOADING AND TIRE PRESSURE Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar.
344 STARTING AND OPERATING Tire and Loading Information Placard Tire And Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
346 STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 347 1.
348 STARTING AND OPERATING WARNING! •Unequal tire pressures can cause steering problems. You could lose control of your vehicle. •Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. •Always drive with each tire inflated to the recommended cold tire inflation pressure. 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread.
STARTING AND OPERATING 349 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire Placard Location The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure.
350 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter. Example: If garage temperature = 68°F (20°C) and the outside temperature = 32°F (0°C) then the cold tire inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition.
STARTING AND OPERATING Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or six, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
352 STARTING AND OPERATING DO NOT install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. DO NOT install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, DO NOT take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING Tire Spinning When stuck in mud, sand, snow, or ice conditions, DO NOT spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. 353 Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. For additional information, refer to “Freeing A Stuck Vehicle” in Section 6. WARNING! Fast spinning tires can be dangerous.
354 STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed. (Refer to the paragraph on “Tread Wear Indicators”). Refer to the “Tire and Loading Information” placard for the size designation of your tire.
356 STARTING AND OPERATING WARNING! • NEVER use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have an accident. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left.
STARTING AND OPERATING SUPPLEMENTAL TIRE PRESSURE INFORMATION — IF EQUIPPED A light load vehicle condition is defined as two passengers [150 lbs (68 kg) each] plus 200 lbs (91 kg) of cargo. Cold tire inflation pressures for a lightly loaded vehicle will be found on the face of the driver’s door. TIRE CHAINS Use “Class S” chains on 1500 model Trucks, or other traction aids that meet SAE Type “S” specifications.
358 STARTING AND OPERATING These cautions apply to all chain traction devices, including link and cable (radial) chains. Tire chain use is permitted only on the rear tires of 4X2 model trucks. NOTE: The use of class “S” chains is permitted on 1500 model trucks with P245/70R17 tires only. NOTE: The use of class “U” chains is permitted on the front and rear of 4X4, 2500 model trucks with LT245/ 70R17E tires.
STARTING AND OPERATING SNOW TIRES Snow tires should be of the same size and type construction as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition. While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires.
360 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. NOTE: On Canadian vehicles only, if your vehicle is equipped with All-Season type tires on the front and ON/OFF Road type tires mounted on the rear, do not use a front-to-back rotation pattern.
STARTING AND OPERATING Dual Rear Wheels 361 CAUTION! 3500 Dual Rear Tires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the ON/OFF road tire and the use of Outline White Letter (OWL) tires. The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires.
362 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire inflation placard pressure. The placard pressure is defined on the Tire and Loading Information label. The Tire and Loading Information label is located on the drivers side B-pillar.
STARTING AND OPERATING The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold placard pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the recommended cold placard pressure in order for the TPMS warning lamp to be turned off.
364 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the Tire Pressure Monitoring Sensor. NOTE: • The TPMS is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure.
STARTING AND OPERATING Tire Pressure Monitor System (TPMS) “Light Load” Reset Switch Description – If Equipped WARNING! Never operate your vehicle with the TPMS and tire pressures set to the Light Load Inflation Pressure settings if carrying more than two occupants (150 lbs each) plus 200 pounds of cargo. The vehicle “Light Load Definition” is found in the Supplemental Tire Pressure Information Label which is located on the rear face of the driver door.
366 STARTING AND OPERATING “Light Load” Reset Switch Operation – If Equipped • This vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the Tire Loading Information Label and the Supplemental Tire Pressure Information Label. It is also equipped to be driven with tire pressures appropriate to either a Light Load condition or the vehicle Max Load condition.
STARTING AND OPERATING 367 Tire Pressure Information label. The Supplemental Tire Pressure Information label is located on the rear face of the driver door. Use an accurate tire gauge to check the tire pressures when lowering all four tire pressures. After all four tire pressures have been lowered to the Light Load inflation pressures, press the “Light Load” reset switch.
368 STARTING AND OPERATING WARNING! It is the driver’s responsibility to change to the max load inflation pressure (cold) low pressure warning threshold condition when not driving in the light load condition as defined as two occupants ( 150 lbs each) plus 200 pounds of cargo. The vehicle “Light Load Definition” is found in the Supplemental Tire Pressure Information label located on the rear face of the driver door.
STARTING AND OPERATING NOTE: It is particularly important, for you to check the tire pressure in all of your tires regularly and to maintain the proper pressure.
370 STARTING AND OPERATING the ignition key is cycled, this sequence will repeat, providing the system fault still exists. A system fault can occur by any of the following scenarios: 1. This spare tire does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the tire pressure in the spare tire. 1. Signal interference due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2.
STARTING AND OPERATING Light will turn OFF, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
372 STARTING AND OPERATING for optimum performance. The use of premium gasoline is not recommended. Under normal conditions, the use of premium gasoline will not provide a benefit over highquality regular and mid-grade gasolines, and in some circumstances may result in poorer performance. and durability for your vehicle. We recommend the use of gasolines that meet the WWFC specifications if they are available. Light spark knock at low engine speeds is not harmful to your engine.
STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the Winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol or E85 Ethanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components.
374 STARTING AND OPERATING allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline. Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. Therefore, you should not have to add anything to the fuel.
STARTING AND OPERATING NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill.
376 STARTING AND OPERATING CAUTION! CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly-fitted aftermarket cap can cause the MIL (Malfunction Indicator Light) to illuminate, due to fuel vapors escaping from the system. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
STARTING AND OPERATING NOTE: Tighten the gas cap 1/4 turn until you hear one click. This is an indication that the cap is properly tightened. If the gas cap is not tightened properly, the Malfunction Indicator Light will come on, Be sure the gas cap is tightened every time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
378 STARTING AND OPERATING sections of this manual for information on features that are common between Flexible Fuel and gasoline-only powered vehicles. CAUTION! Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85.
STARTING AND OPERATING 379 ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. For best results, a refueling pattern that alternates between E-85 and unleaded gasoline should be avoided. When you do switch fuels, it is recommended that you: WARNING! • do not switch when the fuel gauge indicates less than 1/4 full Ethanol vapors are extremely flammable and could cause serious personal injury.
380 STARTING AND OPERATING Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles Flexible Fuel Vehicles (FFV) vehicles operated on E-85 require specially formulated engine oils. These special requirements are included in Mopart engine oils, and in equivalent oils meeting DaimlerChrysler Specification MS-6395. The manufacturer only recommends engine oils that are API Certified and meet the requirements of Material Standard MS-6395.
STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. CAUTION! 381 Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.
382 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded. Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for increased durability does not necessarily increase the vehicle’s GVWR.
STARTING AND OPERATING Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire vehicle should first be weighed on a commercial scale to insure that the GVWR has not been exceeded. The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over front and rear axle.
384 STARTING AND OPERATING An EXAMPLE of a loaded vehicle is shown in the following chart. Note that neither GVWR nor GAWR capabilities are exceeded. Overloading can cause potential safety hazards and shorten service life. NOTE: The weights shown in this chart are not necessarily the weights for your vehicle.
STARTING AND OPERATING TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
386 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
STARTING AND OPERATING Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the truck. These kind of hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers. Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars.
388 STARTING AND OPERATING WARNING! An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking performance, and could result in an accident. Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
STARTING AND OPERATING 389 Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Improper Adjustment Of Weight-Distributing System Trailer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment.
390 STARTING AND OPERATING Trailer Hitch Classification Definitions Class Max. Trailer Hitch Industry Standards Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium 3,500 lbs (1587 kg) Duty Class III - Heavy Duty 5,000 lbs (2268 kg) Class IV - Extra 10,000 lbs (4540 kg) Heavy Duty Fifth Wheel/ Greater than 10,000 lbs (4540 Gooseneck kg) Refer to “Trailer Towing Weights (Maximum Trailer Weight Ratings)” for the website address that contains the necessary information for your specific drivetrain.
STARTING AND OPERATING Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. 391 Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
392 STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: Perform the maintenance listed in Section 8 of this manual. When towing a trailer, never exceed the GAWR, or GCWR, ratings. WARNING! CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h).
STARTING AND OPERATING loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure or tires. • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle.
394 STARTING AND OPERATING Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the Tires–General Information section of this manual on Tire Pressures for proper tire inflation procedures. − Also, check the trailer tires for proper tire inflation pressures before trailer usage.
STARTING AND OPERATING 395 CAUTION! WARNING! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
396 STARTING AND OPERATING Towing Requirements — Trailer Lights & Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4 and 7 pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness.
STARTING AND OPERATING 397 WARNING! Any work done to the vehicles electrical system, or wiring, should be performed by a qualified automotive technician, if done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury.
398 STARTING AND OPERATING The following chart identifies the maximum electrical loads that the trailer tow output circuits are capable of supporting. Trailer Tow Additional Lamp Loads Output FuncMaximum Cur- Additional Bulbs tions rent Allowed Example Only. Other bulb combinations can be used as long as maximum current is not exceeded.
STARTING AND OPERATING NOTE: Using the “TOW HAUL” or “OD/OFF” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking. The automatic transmission fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation.
400 STARTING AND OPERATING − Air Conditioning Turn off temporarily. − refer to Cooling System Operating information in the Maintenance section of this manual for more information. Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface.
STARTING AND OPERATING 401 SNOWPLOW Snowplow Prep Packages are available as a factoryinstalled option. These packages include components necessary to equip your vehicle with a snowplow. 1500 Models (Light Duty) NOTE: Do not use 1500 (light duty) Models for snowplow applications. WARNING! Trailer Towing Position On 1500 Models, snowplows, winches, and other aftermarket equipment should not be added to the front end of your vehicle.
402 STARTING AND OPERATING CAUTION! WARNING! Using 1500 Model vehicles for snowplow applications can cause damage to the vehicle. Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual NOTE: Before installation of a snowplow, it is highly recommended that the owner/installer obtain and follow the recommendations contained within the current Dodge BODY BUILDER’S GUIDE.
STARTING AND OPERATING Before Plowing • Check the hydraulic system for leaks and proper fluid level. • Check the mounting bolts and nuts for proper tightness. • Check the runners and cutting edge for excessive wear. The cutting edge should be 1/4 to 1/2 inch (6.4 mm to13 mm) above ground in snow plowing position. • Check that snowplow lighting is connected and functioning properly. Snowplow Model Prep Package Availability For Detailed Information Visit www.dodge.
404 STARTING AND OPERATING necessary at the beginning and end of the snowplow season. This will help prevent uneven tire wear. Methods For Removing Snow The blade should be lowered whenever the vehicle is parked. Maintain and operate your vehicle and snowplow equipment following the recommendations provided by the specific snowplow manufacturer. Over the Road Operation With Snowplow Attached The blade restricts airflow to the radiator and causes the engine to operate at higher than normal temperatures.
STARTING AND OPERATING NOTE: During snowplow usage on vehicles equipped with an overhead console module, the outside temperature display will show higher temperatures than the outside ambient temperature. The higher displayed temperature is due to blocked or reduced airflow to the underhood ambient temperature sensor by the snowplow. This is common, and outside temperature display operation will return to normal when the snowplow is removed.
406 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational Towing – 4-Wheel Drive Models CAUTION! CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Recreational Towing – 2-Wheel Drive Models Recreational towing of 2-Wheel Drive models is not allowed. Towing with the rear wheels on the ground can result in severe transmission damage.
STARTING AND OPERATING Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped Use the following procedure to prepare your vehicle for recreational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recreational towing to prevent damage to internal parts. 6. Start the engine. 7. Shift automatic transmission into REVERSE. 8. Release brake pedal for five seconds and ensure that there is no vehicle movement. 9.
408 STARTING AND OPERATING CAUTION! Damage to the automatic transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL ensure that the engine is OFF prior to shifting the transmission into PARK. Returning to Normal Operation — Manual Shift Transfer Case Use the following procedure to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop. 2. Apply the parking brake. 3.
STARTING AND OPERATING 409 CAUTION! CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recreational towing, to prevent damage to internal parts. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts. 1. Bring vehicle to a complete stop. 2. Shut OFF the engine.
410 STARTING AND OPERATING 7. After shift is completed and the NEUTRAL light comes on, release the NEUTRAL button. 8. Start engine. 9. Shift automatic transmission into REVERSE. 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 11. Repeat steps 9 and 10 with the transmission in DRIVE. 12. Shut engine OFF and place ignition key in the unlocked OFF position. 13. Shift automatic transmission into PARK or 1st gear on manual transmissions. 14. Apply parking brake. 15.
STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL ensure, that the engine is OFF prior to shifting the transmission into PARK. Returning to Normal Operation — Electronic Shift Transfer Case Use the following procedure to prepare your vehicle for normal usage: 411 4. Depress the brake pedal. 5.
412 STARTING AND OPERATING NOTE: Steps 1 through 5 are requirements that must be met prior to depressing the transfer case Neutral (N) button, and must continue to be met until one second elapses and the shift has been completed.
STARTING AND OPERATING CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts. 413 EQUIPMENT IDENTIFICATION PLATE The Equipment Identification Plate is located on the hood inner surface.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 416 m Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 417 m Jump-Starting Procedures . . . . . . . . . . . . . . . . . 434 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . . 417 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 437 ▫ Reinstalling The Scissors-Type Jack And Tools (1500 Models) . . . .
416 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. To engage the Hazard Warning lights, depress the button on the top of the steering column. When the Hazard Warning switch is activated, all directional turn signals will flash off and on to warn oncoming traffic of an emergency. Push the button a second time to turn off the flashers.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to an authorized service center where it can be raised on a lift.
418 WHAT TO DO IN EMERGENCIES Removal (1500 Regular Cab/Quad Cabt Vehicles) Jack Wing Bolt Jack Cover The jack and jack tools are stored under the front passenger seat. Lift the tab and slide the plastic cover forward for access. Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat.
WHAT TO DO IN EMERGENCIES WARNING! 419 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-screw. After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
420 WHAT TO DO IN EMERGENCIES 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows), and tie to the jack using the tie straps.
WHAT TO DO IN EMERGENCIES 421 6 Jack and Tools Tied 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt. Reinstall the plastic cover.
422 WHAT TO DO IN EMERGENCIES JACKING INSTRUCTIONS Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
WHAT TO DO IN EMERGENCIES Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to an authorized service center where it can be raised on a lift. Do not raise this vehicle using a bumper jack.
424 WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked. WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
WHAT TO DO IN EMERGENCIES 425 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. Placement of the Jack: • For 1500 series trucks, when changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below.
426 WHAT TO DO IN EMERGENCIES 1500 4X4 Jacking Location • For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. 4X2 Jacking • Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required.
WHAT TO DO IN EMERGENCIES • For 2500/3500 4x4 series trucks, when changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench. 427 • For all trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
428 WHAT TO DO IN EMERGENCIES • Connect the jack tube extension and wheel wrench. Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. NOTE: If the 2500/3500 bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface.
WHAT TO DO IN EMERGENCIES 429 WARNING! NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. Hub Caps/Wheel Covers The hub caps must be removed before raising the vehicle off the ground. 7. Install wheel center cap and remove wheel blocks.
430 WHAT TO DO IN EMERGENCIES CAUTION! Use a back-and-forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap finish may occur. CAUTION! The rear hub caps on the dual rear wheel has two pry-off notches. Make sure that the hook of the jack handle driver is located squarely in the cap notch before attempting to pull off. You must use the flat end of the lug wrench to pry off the wheel skins.
WHAT TO DO IN EMERGENCIES 8-Stud — Dual Rear Wheels Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer. 431 Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assembling the wheels for best access to the tire valve on the inner wheel.
432 WHAT TO DO IN EMERGENCIES These dual rear wheels should be tightened as follows: 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved. Retighten to specifications at 100 mi (160 km) and after 500 mi (800 km). It is recommended that wheel stud nuts be kept torqued to specifications at all times.
WHAT TO DO IN EMERGENCIES tightened to recommended torque. Tighten the nuts to final torque in increments. Progress around the bolt circle, tightening the nut opposite to the nut just previously tightened until final torque is achieved. Recommended torques are shown in the following chart. Disc Wheels Type Nut Stud Size Torque Ft. Lbs.
434 WHAT TO DO IN EMERGENCIES HOISTING A conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking locations. However, a floor jack or frame hoist must never be used on any other parts or the underbody. CAUTION! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle may result. JUMP-STARTING PROCEDURES Do not attempt to push or tow your vehicle to get it started.
WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. 435 2. Park the booster vehicle within cable reach but without letting the vehicles touch.
436 WHAT TO DO IN EMERGENCIES WARNING! • You should not try to start your vehicle by pushing or towing. • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode.
WHAT TO DO IN EMERGENCIES 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
438 WHAT TO DO IN EMERGENCIES EMERGENCY TOW HOOKS — IF EQUIPPED Your vehicle may be equipped with emergency tow hooks. NOTE: For off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle. WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. WARNING! CAUTION! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to the main structural members of the vehicle—not to bumpers or associated brackets. State and local laws applying to vehicles under tow must be observed.
440 WHAT TO DO IN EMERGENCIES CAUTION! Towing faster than 30 mph (50 km/h) or for more than 15 mi (25 km) can cause severe damage to the transmission. If the vehicle is to be towed faster than 30 mph (50 km/h) or more than 15 mi (25 km) the vehicle must be towed with the rear wheels raised and the front wheels on the ground. It may also be towed on a flatbed or with the front wheels raised and the rear wheels on a dolly.
MAINTAINING YOUR VEHICLE CONTENTS m Engine Compartment— 3.7L . . . . . . . . . . . . . . . 444 m Maintenance Procedures . . . . . . . . . . . . . . . . . . 450 m Engine Compartment— 4.7L . . . . . . . . . . . . . . . 445 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 451 m Engine Compartment— 5.7L . . . . . . . . . . . . . . . 446 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 454 m Onboard Diagnostic System (OBD II) . . . . . . . . .
442 MAINTAINING YOUR VEHICLE ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 457 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 465 ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 459 ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . . 470 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 460 ▫ Fuel System Connections . . . . . . . . . . . . . . . . 471 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 460 ▫ Brake System . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Noise Control System Required Maintenance & Warranty For 3500 2-Wheel Drive And 4-Wheel Drive Models Over 10,000 Lbs. (4 535 Kg) Gross Vehicle Weight Rating. . . . . . . . . . . . . . 480 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 484 m Fuses (Integrated Power Module) . . . . . . . . . . . 489 m Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . 493 m Replacement Light Bulbs . . . . . . . . . . . . . . . . .
444 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 3.
MAINTAINING YOUR VEHICLE 445 ENGINE COMPARTMENT— 4.
446 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
448 MAINTAINING YOUR VEHICLE tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will blink for approximately five seconds and then remain on until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station.
450 MAINTAINING YOUR VEHICLE AUTHORIZED DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Always maintain the oil level within the SAFE zone on the dipstick.
452 MAINTAINING YOUR VEHICLE Change Engine Oil Follow the Maintenance Schedule for recommended engine oil change intervals. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API-certified and meet the requirements of DaimlerChrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE NOTE: Vehicles equipped with a 5.7L engine must use SAE 5W-20 oil. Failure to do so may result in improper operation of the Multi-Displacement System (MDS). Refer to “Multi-Displacement System” under “Starting and Operating” in Section 5. NOTE: For 2500/3500 trucks with a 5.7L engine operating under a gross combined weight rating of 14,000 lbs. or greater, SAE 5W-30 engine oil is recommended for all operating temperatures.
454 MAINTAINING YOUR VEHICLE Engine Oil Filter The engine oil filter should be replaced at every engine oil change. At the mileage indicated in the maintenance schedule, all belts and tensioner should be checked for condition. Improper belt tension can cause belt slippage and failure. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Follow the Maintenance Schedule for recommended Engine Air Cleaner Filter change intervals. WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance.
456 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE 457 To minimize the possibility of catalyst damage: Emission-Related Components • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. Positive Crankcase Valve (PCV) Proper operation of the crankcase ventilation system requires that the PCV valve be free of sticking or plugging from deposits. Deposits can accumulate in the PCV valve and passages with increasing mileage.
458 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. NOTE: Refer to Section 3 of the Warranty Information book for further warranty information.
460 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency (EPA) and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment. Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required.
MAINTAINING YOUR VEHICLE The ball joints originally supplied with the vehicle are permanently lubricated at the factory and do not require service. However, if the seals on the ball joints are damaged, the joints should be replaced. Serviceable replacement ball joints are available. Front suspension ball joints should be replaced only by a qualified service technician using tools specially designed for this purpose.
462 MAINTAINING YOUR VEHICLE Front Prop Shaft Lubrication — 2500/3500 (4X4) Models Lubricate the front driveshaft grease fitting at each oil change listed in the appropriate Maintenance Schedule for your vehicle. Use Mopart type MS-6560 (lithiumbased grease), or equivalent.
MAINTAINING YOUR VEHICLE 463 Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. reservoir with windshield washer solvent only (not radiator antifreeze). When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance.
464 MAINTAINING YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to Exhaust Gas in the Safety Tips section of this manual. Exhaust System Rubber Isolator and Loop-Type Hanger — If Equipped Inspect surfaces whenever the vehicle is hoisted for rubber to metal separation or deep cracks.
466 MAINTAINING YOUR VEHICLE accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks.
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do not use plain water alone or alcohol-base engine coolant (antifreeze) products.
468 MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.
MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol-based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
470 MAINTAINING YOUR VEHICLE • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks.
MAINTAINING YOUR VEHICLE Ensure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure.
472 MAINTAINING YOUR VEHICLE Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant operations to facilitate the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage.
MAINTAINING YOUR VEHICLE With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. For correct fluid type, refer to ”Brake Master Cylinder” under “Fluids, Lubricants and Genuine Parts” in this section.
474 MAINTAINING YOUR VEHICLE Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance-free system. In the event of leakage or other malfunction, the system must be replaced. Clutch Linkage If the clutch pedal linkage begins to squeak or grunt, the clutch pedal pivot bushings should be lubricated. For the correct lubricant type, refer to “Fluids, Lubricants and Genuine Parts” in this Section.
MAINTAINING YOUR VEHICLE NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. Limited-Slip Differentials in 1500 Model vehicles require that 4 oz. (118 ml) Mopart limited slip additive be added to the gear lubricant.
476 MAINTAINING YOUR VEHICLE Manual Transmission Lubricant Selection G238 (6-Speed Manual Transmission — If Equipped) This transmission is filled with manual transmission fluid at the factory. This fluid does not require periodic changing. If it is necessary to add or change fluid in this transmission refer to Fluids, Lubricants and Genuine Parts for correct fluid type. This is the only lubricant recommended for use in the Getrag 238 transmission.
MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants and Genuine Parts” in this section for correct fluid type. Fluid Level Check If equipped with a dipstick, use the following procedure.
478 MAINTAINING YOUR VEHICLE 3. Fully apply the parking brake and press the brake pedal. 4. Place the gear selector momentarily in each gear position ending with the lever in PARK. 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature. Verify that solid coating of oil is seen on both sides of the dipstick.
MAINTAINING YOUR VEHICLE 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube. Automatic Transmission Fluid and Filter Change Follow the Maintenance Schedule for recommended transmission fluid and filter change intervals.
480 MAINTAINING YOUR VEHICLE Rear Wheel Bearings — Manufacturer’s Axles These bearings are normally considered permanently lubricated. Cleaning and repacking is required only when axle shafts are removed or in case of extreme water or dust contamination. Noise Control System Required Maintenance & Warranty For 3500 2-Wheel Drive and 4-Wheel Drive models over 10,000 lbs. (4 535 kg) Gross Vehicle Weight Rating.
MAINTAINING YOUR VEHICLE Required Maintenance for Noise Control Systems The following maintenance services must be performed every six months or 6,000 mi (9 600 km), whichever comes first, to assure proper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed or suspected. Proper maintenance of the entire vehicle will help the effectiveness of the noise control systems.
482 MAINTAINING YOUR VEHICLE EXHAUST SYSTEM • Removal or rendering inoperative exhaust system components including the muffler or tailpipe. ENGINE COOLING SYSTEM • Removal or rendering inoperative the fan clutch. • Removal of the fan shroud. Noise Emission Warranty The manufacturer warrants that this vehicle as manufactured by the manufacturer, was designed, built and equipped to conform at the time it left the manufacturer’s control with all applicable U.S. EPA Noise Control Regulations.
MAINTAINING YOUR VEHICLE 483 Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed.
484 MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE 485 • Use Mopart Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • If you detect any stone chips or scratches in the paint, touch them up immediately.
486 MAINTAINING YOUR VEHICLE • Use Mopart touch up paint on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use Mopart Wheel Cleaner (05066247AB) or equivalent, or select a nonabrasive, non-acidic cleaner.
MAINTAINING YOUR VEHICLE Interior Care Use Mopart Total Clean to clean fabric upholstery and carpeting. Use Mopart Total Clean to clean vinyl upholstery. Mopart Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
488 MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopart Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements.
MAINTAINING YOUR VEHICLE FUSES (INTEGRATED POWER MODULE) An integrated power module is located in the engine compartment near the battery. This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
490 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 9 30 Amp Pink 10 5 Amp Orange 11 20 Amp Yellow Description Off Road Module Power Trx-Off Rd Pkg Sen (Gas Engine Only) NOTE: Insert 5 amp fuse in this cavity to enable the TRX capability (If Equipped).
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 20 10 Amp Red 21 10 Amp Red 22 2 Amp Gray 23 10 Amp Red 24 20 Amp Blue 25 10 Amp Red 26 20 Amp Yellow Description Occupant Restraints Controller (ORC) 2 Occupant Restraints/ Pass Disable Switch IGN Switch Feed Cavity Cartridge Mini Fuse Fuse 27 40 Amp Green 28 10 Amp Red 29 HVAC 30 AISIN Relay Feed (Diesel Only) Power Mirror/T-Case Brake Brake Switch/Center High Mount Stop Light (CHMSL)/ Aftermarket CHMSL 31 10 Amp Red 15 Amp Blue 10 Amp Red 4
492 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 32 10 Amp Red 33 34 35 36 37 38 10 Amp Red — 15 Amp Blue 25 Amp Natural 15 Amp Blue 20 Amp Yellow Description Power Ignition Run — Adjustable Pedals LED Power-IGN Run — HVAC — Cabin Compartment Node (CCN) Illumination Audio_Amplifier Variable Gate Turbo (VGT) — Turbo Diesel Power Outlet IP Cavity Cartridge Mini Fuse Fuse 39 10 Amp Red 40 20 Amp Yellow 41 42 — 30 Amp Pink Description Seatbelt Tension Reducer/Power IGN Run/Acc Power IGN R
MAINTAINING YOUR VEHICLE CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
494 MAINTAINING YOUR VEHICLE • Any time you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
MAINTAINING YOUR VEHICLE LIGHT BULBS — Exterior Bulb No. Tail & Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057 Cab Clearance Lights . . . . . . . . . . . . . . . . . . . . . . 168 Dual Rear Wheel Sidemarker Light . . . . . . . . . . . . 168 Dual Rear Wheel Tailgate ID Lights (3) . . . . . . . . . 168 495 1. Open the hood 2. Remove the two bolts from the front of the headlight housing. BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb.
496 MAINTAINING YOUR VEHICLE 3. Remove the plug from the inner fender well and remove the nut through the access hole. Rear Headlight Housing Nut Access Inner Fender Plug 4. Pull the housing out from the fender to allow room to disconnect the electrical connectors. NOTE: For easier removal, pull the headlight assembly straight forward, applying the greatest amount of force to the outer edge of the headlight assembly.
MAINTAINING YOUR VEHICLE Headlight Removal Bulb Removal 497 7
498 MAINTAINING YOUR VEHICLE 5. Unlock and pull connector straight from the base of the headlight halogen bulb. 6. Twist connector on the side marker/turn signal/park light bulb 1⁄4 turn and remove connector and bulb from housing. 7. Remove housing from vehicle with headlight halogen bulb in housing. 8. Twist the headlight halogen bulb 1⁄4 turn and remove headlight bulb from the housing. 9. Replace headlight or side marker/turn signal/park light bulb. Do not touch the headlight halogen bulb. 10.
MAINTAINING YOUR VEHICLE 2. Pull bulb straight from the connector. 499 Tail, Stop, Turn and Backup Lights 1. Remove the two screws that pass through the bed sheetmetal. 7 3. Reverse procedure for installation of bulbs and housing.
500 MAINTAINING YOUR VEHICLE 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged. 3. Rotate the bulb socket counterclockwise to remove from the housing.
MAINTAINING YOUR VEHICLE 4. Pull bulb straight out of socket. 501 5. Reverse Procedure to install bulb and housing. Place the two raised blocks past the body.
502 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight (CHMSL) With Cargo Light 2. Separate the connector holding the housing and wiring harness to the body. 1. Remove the two screws holding the housing/lens to the body as shown. 3. Turn desired bulb socket 1⁄4 turn and remove socket and bulb from housing.
MAINTAINING YOUR VEHICLE 4. Pull desired bulb straight from the socket. 503 Cab Top Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. • Outside Bulbs: Cargo Lights • Inside Bulb: Center High-Mounted Stop Light 5. Reverse procedure for installation of bulbs and housing.
504 MAINTAINING YOUR VEHICLE 2. Rotate the socket 1⁄4 turn and pull it from the light assembly. 3. Pull the bulb straight from it’s socket and replace.
MAINTAINING YOUR VEHICLE 505 Tailgate ID Lights (Dual Rear Wheels) — If Equipped 1. Remove the two screws and housing and access the bulb sockets from the rear.
506 MAINTAINING YOUR VEHICLE 2. Turn socket 1⁄4 turn counterclockwise to access the bulb. Rear Light Bar ID Marker (Dual Rear Wheel) — If Equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and housing. 2. Turn the socket 1⁄4 turn counterclockwise to access the bulb.
MAINTAINING YOUR VEHICLE 507 3. Pull the bulb straight out from the socket. 2. Pull the entire assembly from the fender. 4. Reverse procedure for installation of bulbs and housing. 3. Turn socket 1⁄4 turn counterclockwise and remove from assembly to access the bulb. Side Marker Lights (Dual Rear Wheels) 4. Pull bulb straight out from socket. 5. Reverse procedure for installation of bulbs and housing. 7 1. Push rearward on the side marker light assembly.
508 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S.
MAINTAINING YOUR VEHICLE Engine Oil (with filter) 3.7L Engine V-6 (SAE 5W-20, API Certified) 4.7L Engine V-8 (SAE 5W-20, API Certified) 5.7L Engine V-8 (SAE 5W-20, API Certified). For trucks operating under a gross combined weight rating less than 14,000 lbs. 5.7L Engine V-8 (SAE 5W-30, API Certified). For 2500/3500 trucks operating under a gross combined weight rating greater than 14,000 lbs. Cooling System 3.7L (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. 4.
510 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). Engine Oil (3.7/4.7L Engine) Use SAE 5W-20, API Certified, meeting material standard MS-6395. 5.7L Engine Oil (For trucks operat- Use SAE 5W-20, API Certified, meeting material standard MS-6395. ing under a gross combined weight rating less than 14,000 lbs/ (6,350 kg.) 5.
MAINTAINING YOUR VEHICLE Component Engine Oil Filter (4.7L & 5.7L Engine) Spark Plugs (5.7L Engine) Spark Plugs (4.7L Engine) Spark Plugs (3.7L Engine) Fuel Selection (3.7L/4.7L Engine) Fuel Selection (5.7L Engine) 511 Fluids, Lubricants and Genuine Parts Mopart Engine Oil Filter, P/N 4884899AB or equivalent. REC14MCC4 (Gap 0.043 in [1.09 mm]) Upper Bank — FR8TE2 (Gap 0.039 in [.99 mm]) Lower Bank — FR8T1332 (Gap 0.051 in [1.30 mm]) ZFR6F-11G (Gap 0.043 in [1.
512 MAINTAINING YOUR VEHICLE Component Clutch Linkage 1500 Model Front Axle (4X4) 1500 Model Rear Axle 2500/3500 Model Front and Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Multipurpose Grease, NLGI Grade 2 E.P. or equivalent. GL-5 SAE 75W-90 (MS-9763) or equivalent. Mopart Synthetic Gear Lubricant SAE 75W-140 (MS-8985). Limited-Slip Rear Axles on 1500 Models Require the addition of 118 ml (4 oz.) Mopart Limited Slip Additive or equivalent.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . . . 514 m Maintenance Schedule . . . . . . . . . . . . . . . . . . . 514 ▫ Required Maintenance Intervals . . . . . . . . . . .
M A I N T E N A N C E 514 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Your dealer will reset the oil change indicator message after completing the scheduled oil change.
M A I N T E N A N C E S C H E D U L E S 8 516 MAINTENANCE SCHEDULES At Each Oil Change Required Maintenance Intervals • Change the engine oil filter. NOTE: ** Vehicles built with the 4.7L engine are equipped with sixteen spark plugs, one set is located on the top of the engine under the coils and the second set is located on the side of the engine. • Inspect the brake hoses and lines. • Check the Manual Transmission fluid level.
MAINTENANCE SCHEDULES 517 M Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Change the engine oil and engine oil filter. Rotate Tires. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Lube Front Drive Shaft Fitting (2500/3500, 4x4 only). If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. Inspect the brake linings, replace if necessary.
M 518 MAINTENANCE SCHEDULES A I N T E N Maintenance Items A N Inspect Exhaust System. Perform the first inspection at C 12,000 miles (20 000 km) or 12 months. E Inspect the front suspension, tie rod ends and boot S C H E D U L E S 8 seals, replace if necessary. Replace the engine air cleaner filter. Inspect the transfer case fluid. Replace the top row of spark plugs on 4.7L engines. ** Replace the spark plugs on 3.7L and 5.7L engines.
MAINTENANCE SCHEDULES 519 M Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Change the manual transmission fluid if using your vehicle for any of the following: trailer towing, snow plowing, heavy loading, taxi, police, delivery service (commercial service), off-road, desert operation or more then 50% of your driving is at sustained high speeds during hot weather, above 90F° (32C°). Inspect and replace PCV valve if necessary.
M 520 MAINTENANCE SCHEDULES A I N WARNING! T E You can be badly injured working on or around a N motor vehicle. Do only that service work for which A N you have the knowledge and the right equipment. If C you have any doubt about your ability to perform a E S C H E D U L E S 8 service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . . 525 ▫ Prepare For The Appointment . . . . . . . . . . . . 523 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . . 525 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 523 m Warranty Information (U.S. Vehicles Only) . . . . .
522 IF YOU NEED CONSUMER ASSISTANCE m Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 528 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . 529 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 529 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
524 IF YOU NEED CONSUMER ASSISTANCE high quality service. The manufacturer’s authorized dealers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership.
IF YOU NEED CONSUMER ASSISTANCE Chrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: (800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F.
526 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590.
528 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
530 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
532 INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 144 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . . . . . . . . . . . . 455,481 Air Conditioner Maintenance . . . . . . . . . . . . . . . 459 Air Conditioning Refrigerant . . . . . . . . . . . . . 459,460 Air Conditioning System . . . . . . . . . . . . . . . . 261,459 Air Conditioning System, Zone Control . . . . . . . . 264 Air Pressure, Tires . . . . . .
INDEX Axle Lubrication (Axle Fluid) . . . . . . . . . . . . . . . 474 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 434 Saving Feature (Protection) . . . . . . . . . . . . . . . 136 Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454 Belts, Seat . . . .
534 INDEX Cassette Tape and Player Maintenance . . . . . . . . . 257 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . . 455 CD (Compact Disc) Player . . . . . . . . . . . . 211,219,233 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Center High Mounted Stop Light . . . . . . . . . . . . 502 Center Lap Belts . . . . . . . . . . . . . . . . . . . . . . . . . 45 Center Seat Storage Compartment . . . . . . . . . 173,174 Certification Label . . . . . . . . . . . . . . . . . .
INDEX Pressure Cap . . . . . . . . . . . . . Radiator Cap . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Temperature Gauge . . . . . . . . . Cruise Control (Speed Control) . . Cupholders . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . 468 . . . . . . . . . . . . 468 . . . . . . 466,508,510 . . . . . . . . . . . . 198 . . . . . . . . . . . . 145 . . . . . . . . . . . . 169 . . . . . . . . . . . . 523 Data Recorder, Event . . . . . . . . . . . . .
536 INDEX Electronic Stability Program . . . . . . . . . . . . . . . 333 Traction Control System . . . . . . . . . . . . . . . . . 326 Electronic Roll Mitigation (ERM) . . . . . . . . . . . . . 332 Electronic Speed Control (Cruise Control) . . . . . . 145 Electronic Stability Program (ESP) . . . . . . . . . 204,333 Electronically Shifted Transfer Case . . . . . . . . 298,306 Emergency Brake . . . . . . . . . . . . . . . . . . . . . . . . 318 Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . .
INDEX Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . 455,481 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 455 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 454,510 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 453 Flashers Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Flat Tire Stowage . . . . . . . . . . . . . . . . . . . . . 422,433 Flexible Fuel Vehicles Cruising Range . . . . . . . . . . . . . . . . . . . . . . . .
538 INDEX Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . 508 Fuel, Flexible . . . . . . . . . . . . . See Flexible Fuel Vehicles Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489 Garage Door Opener (HomeLinkt) . . . . . . . . . . . 156 Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . . . . 377,447 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 371 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 372 Gauges . . . . . . . . . . . . . . .
INDEX Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heater, Engine Block . . . . . . . . . . . . . . . . . . High Beam/Low Beam Select (Dimmer) Switch Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . HomeLinkt (Garage Door Opener) Transmitter Hood Release . . . . . . . . . . . . . . . . . . . . . . . Hoses . . . . . . . . . . . . . . . . . . . . . . .
540 INDEX Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Lane Change and Turn Signals . . . . . . . . . . . . . . 139 Lap Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 35 LATCH (Lower Anchors and Tether for CHildren) . . . . . . . 66 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 197 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 494,495 Side Marker . . . . . . . . . . . . . . . . . . . . . . . . . . 507 Tire Pressure Monitoring (TPMS) . . . . . . . . . . . 204 Traction Control . . . . . . . . . . . . . . . . . . . . . . . 333 Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . 298 Transmission Warning . . . . . . . . . . . . . . . . . . . 207 Turn Signal . . . . . . . . . . . . . . . . .
542 INDEX Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . 89,400 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 7 Monitor, Tire Pressure System . . . . . . . . . . . . . . . 362 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 449,526 Multi-Displacement Engine System . . . . . . . . . . . 338 Multi-Function Control Lever . . . .
INDEX Opener, Garage Door (HomeLinkt) . . . . . . . . . . . 156 Operating Precautions . . . . . . . . . . . . . . . . . . . . 447 Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . 87 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 Overdrive OFF Switch . . . . . . . . . . . . . . . . . . . . 285 Overhead Console . . . . . . . . . . . . . . . . . . . . 148,149 Overhead Travel Information Center . . . . . . . . . . 149 Owner’s Manual (Operator Manual) . . . . . . . . . .
544 INDEX Radio, Navigation . . . . . . . . . . . . . . . . . . . . . . . 248 Radio Operation . . . . . . . . . . . . . . . . . . . 211,219,233 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . 255 Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . . 248,251 Radio (Sound Systems) . . . . . . . . . . . . . . 211,219,233 Rear Axle (Differential) . . . . . . . . . . . . . . . . . . . . 474 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . 126,128 Rear Wheel Bearings . . . . . .
INDEX Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Satellite Radio . . . . . . . . . . . . . . . . . . . . . . . 248,251 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 254 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 514 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . 488 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . 46 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . .
546 INDEX Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . 297 Transfer Case, Shifting into Transfer Case Neutral (N) . . . . . . . . . . . . . . . . . . . . . . . . . 407,409 Transfer Case, Shifting out of Transfer Case Neutral (N) . . . . . . . . . . . . . . . . . . . . . . . . . 408,411 Shoulder Belt Upper Anchorage . . . . . . . . . . . . . . 43 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . 453 System, Navigation . . . . . . . . . . . . . . . . . . . . . . 248 System, Remote Starting . . . . . . . . . . . . . . . . . . . . 25 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Tether Anchor, Child Restraint . . . . . . . . . . . . . 66,71 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 143 Tip Start . . . . . . . .
548 INDEX Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 353 Wheel Mounting . . . . . . . . . . . . . . . . . . . . . . . 423 Wheel Nut Torque . . . . . . . . . . . . . . . . . . . . . 428 Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 390 Torque Converter Clutch . . . . . . . . . . . . . . . . . . 288 Tow Hooks, Emergency . . . . . . . . . . . . . . . . . . . 438 Towing . . . . . . . . . . . . . . . . . . . . . .
INDEX Transmitter, Garage Door Opener (HomeLinkt) . . 156 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 353 Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . 199,207 Turn Signals . . . . . . . . . . . . . . . . . . . 139,196,495,499 UConnectt (Hands-Free Phone) Underhood Fuses . . . . . . . . . . Uniform Tire Quality Grades . . Universal Transmitter . . . . . . . . . . . . . . . . . . . . . 91 . . . . . . . . .
550 INDEX Windshield Defroster . . . . . . . . . . . . . . . . . . 260,263 Windshield Washers . . . . . . . . . . . . . . . . 141,142,463 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141,463 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 463 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 141 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 463 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2008 Ram Truck 2008 OWNER’ S MANUAL 81-326-0827 Fourth Edition Printed in U.S.A.
