2007 SPRINTER 81-326-0799 First Edition Printed in U.S.A.
Thank you for choosing the new Sprinter. Before your first journey, please familiarize yourself with your vehicle and how it operates, as well as its driving, control and convenience functions. Before you drive off, read these Operating Instructions. This will help you get the most out of your vehicle and avoid endangering yourself and others. Since the scope of delivery is based on the sales order, your vehicle’s equipment may differ from some descriptions and illustrations.
Contents Introduction. . . . . . . . . . . . . . . 3 1 At a glance . . . . . . . . . . . . . . . 11 2 Safety . . . . . . . . . . . . . . . . . . . 23 1 3 Controls in detail . . . . . . . . . 51 4 Operation . . . . . . . . . . . . . . . 173 5 Practical hints. . . . . . . . . . . 249 6 *Technical data. . . . . . . . . . 351 Index . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Environmental protection Do not carry any unnecessary weight in/on the vehicle. Environmental concerns and recommendations DaimlerChrysler’s declared policy is one of comprehensive environmental protection. Keep an eye on the vehicle’s fuel consumption. The objectives are for the natural resources which form the basis of our existence on this planet to be used sparingly and in a manner which takes the requirements of both nature and humanity into account.
Introduction Operating safety Operating safety Warning G Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles, and certain products of component wear, contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction Operating safety Warning G A heavy impact to the underbody, tires or wheels, for example when bottoming out on rough terrain or driving over an obstacle at high speed, could damage your vehicle. This also applies to vehicles equipped with underbody protection. In this case, have your vehicle checked at an authorized Sprinter Dealer which has the necessary specialist knowledge and tools to carry out the work required.
Introduction Operating safety Digital speedometer and total distance recorder Do not allow the electronically stored total distance covered by your vehicle to be modified as a result of tampering with the electronics system. This type of modification or failing to inform the buyer when selling the vehicle could constitute an offense punishable by law, depending on the country concerned.
Introduction Operating safety Body builders and dealers who make any modifications which may affect the final certification of the engine, vehicle or equipment assume the sole responsibility for the vehicle, including labeling and documentation, affected by their modifications.
Introduction Operating safety Warning G Various warning labels are affixed to your vehicle. These warning labels are intended to make you and others aware of various risks. You should not remove any of these warning labels unless explicitly instructed to do so by information on the label itself. Removal of any of these labels may cause you and others to be unaware of certain risks which may result in an accident and/or personal injury.
Introduction REPORTING SAFETY DEFECTS REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect, which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
Introduction Information regarding electronic recording devices Information regarding electronic recording devices (Including notice pursuant to California Code § 9951) Please note that your vehicle is equipped with devices that can record vehicle systems data. This information helps, for example, to diagnose vehicle systems after a collision and to continuously improve vehicle safety.
At a glance Cockpit ............12 Instrument cluster ............14 Steering wheel with buttons* ............17 Center console ............18 Overhead control panel* ............19 Switch units ............20 Door control panel ............
At a glance Cockpit Cockpit 1 N68.
At a glance Cockpit Function Page Function 1 Door control panel 22 7 Instrument cluster 2 Light switch 77 8 Storage compartment Turn signals 79 9 Storage compartment with interior lamp High-beam headlamps 77 3 Combination switch Windshield wipers 126 Rear window wiper* 127 4 Cruise control lever* 147 5 Horn 6 Steering wheel without/ with* buttons 17 Overhead control panel* Page Function 14, 84 f Center console 80 19 g Selector lever (automatic transmission) Page 18 111
At a glance Instrument cluster Instrument cluster 1 N54.
At a glance Instrument cluster Function Page 1 Instrument cluster on vehicles without steering wheel buttons 84 2 Instrument cluster on vehicles with steering wheel buttons* 84 3 87 Selects menus 4 Reset button 84 85 16 7 Indicator and warning lamps 16 8 Display on vehicles without steering wheel buttons 87 9 Display on vehicles with steering wheel buttons* 89 a Tachometer with: 85 b 187 Page Indicator and warning lamps Indicator and warning lamps On vehicles with steering wheel but
At a glance Instrument cluster Indicator and warning lamps 1 v Page ESP® warning lamp 43 268 ASR warning lamp 44 45 268 / Coolant level too low 275 D Coolant temperature too high 275 1 Restraint systems malfunction 272 Brake fluid level too low 269 EBV malfunction 268 Malfunction in trailer's brake booster 269 N Engine oil level warning 274 ± Engine diagnostic indicator lamp 277 q Pre-glow system, diesel engine only 111 276 Turn signal, left 16 79 Indicator and warning lam
At a glance Steering wheel with buttons* Steering wheel with buttons* Function 1 Display Page 89 Controlling the operating system 2 To select a submenu or adjust the volume N46.
At a glance Center console Center console 1 Function 1 Storage compartment 2 Radio* or COMAND*, see the separate operating instructions N68.
At a glance Overhead control panel* Overhead control panel* Function Page Function 4 Eyeglass compartment or 1 Hands-free microphone for telephone* 2 Switches the right-hand reading lamp on/off 81 3 Switches the automatic interior lighting on/off 81 Anti-theft alarm system (ATA)* Page 166 47 5 Switches the interior lighting on/off 80 6 Switches the left-hand reading lamp on/off 81 7 Opens/closes the sliding sunroof* 145 19 1
At a glance Switch units Switch units 1 Center console switch unit Function N54.25-2915-31 & Opens/closes the lefthand electric sliding door* 57 Switches the left/right seat heating* on/off 73 Switches the rear window heating* on/off i The number of switches may vary, depending on the vehicle’s equipment.
At a glance Switch units Function ³ Switches the heater booster function* on/off ö Switches auxiliary heat³ ing* on/off Page Function 137 Switches the rear-compartment convenience interior lighting* on/off 140 Page 82 i Switches the heater booster function* on/off 137 Adjusts the working engine speed* 155 Switches the operating speed governor* on/off 154 Ventilates the load compartment, air in/air out* 146 The layout of the switches may vary, depending on the vehicle’s equipment. N54.
At a glance Door control panel Door control panel 1 Function N54.
Safety Occupant safety ............24 Driving safety systems ............42 Anti-theft systems ............
Safety Occupant safety Occupant safety Restraint systems 2 This section contains all the most important information about the restraint systems in your vehicle. In an accident, your vehicle collides with another object, for example another vehicle. This may cause your vehicle to accelerate or decelerate extremely quickly. During this acceleration or deceleration, the vehicle occupants will be moved in the opposite direction to the force of the impact.
Safety Occupant safety In accidents in which an airbag is activated, the airbag will therefore only offer an increase in the protection provided by the seat belt, i.e. additional protection, if the seat belt is worn correctly.
Safety Occupant safety Do not secure any objects with a seat belt if it is being used by one of the vehicle’s occupants. 2 Avoid wearing bulky clothing, for example a winter coat. Do not route the belt strap over sharp or fragile objects, especially if these are located in or on your clothing, for example eyeglasses, pens or keys. The belt strap could otherwise tear in the event of an accident and you or other vehicle occupants could be injured as a result.
Safety Occupant safety Always have seats belts that are damaged or have been subjected to a heavy load in an accident replaced, and their anchorages checked, at a qualified specialist workshop which has the necessary specialist knowledge and tools to carry out the work required. Wearing seat belts Route the belt over your shoulder. Click belt latch plate 2 into buckle 4. Adjust the belt to the correct height if necessary.
Safety Occupant safety Adjust the belt height in such a way that the shoulder belt is routed over the middle of the shoulder. 2 Slide belt sash guide 1 to the desired height. Let go of release button 5 and make sure that belt sash guide 1 engages.
Safety Occupant safety In this case, have the SRS system checked and repaired immediately at a qualified specialist workshop which has the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at a qualified specialist workshop.
Safety Occupant safety 2 Vehicle deceleration or acceleration and the direction of the force are essentially determined by: the distribution of the force during the impact the collision angle the deformation characteristics of the vehicle the composition of the object involved in the collision, for example the other vehicle Factors that cannot be seen or measured until after the collision are not used to determine whether the airbag should be triggered and are not decisive for this.
Safety Occupant safety Warning G If the emergency tensioning retractors have been triggered, have them replaced at a qualified specialist workshop which has the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at a qualified specialist workshop.
Safety Occupant safety Do not put your feet on the dashboard. Do not lean on the doors from inside the vehicle. 2 Make sure that no persons, animals or objects are present between the vehicle occupants and the deployment range of the airbags.
Safety Occupant safety Warning G After an airbag has been triggered: airbag parts are hot – do not touch them, otherwise you could be burnt the airbags must be replaced at a qualified specialist workshop which has the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at a qualified specialist workshop.
Safety Occupant safety The driver’s front airbag and co-driver’s front airbag are triggered: 2 in the initial stages of an accident with a high rate of vehicle acceleration or deceleration in a longitudinal direction if the system determines that airbag deployment can offer additional protection to that provided by the seat belt independently of other airbags in the vehicle Thorax sidebags* Warning G G Warning G To reduce the risk of injury to occupants if a thorax/sidebag is triggered, make su
Safety Occupant safety In the event of an accident, the thorax sidebag next to the outer seat side inflates between the door and the chest area of the occupant. i You will find additional information about airbag deployment on ( page 32).
Safety Occupant safety i You will find additional information about airbag deployment on ( page 32). 2 You will find additional information about the triggering of emergency tensioning retractors and belt force limiters on ( page 30).
Safety Occupant safety Do not carry heavy or hard objects inside the vehicle or load compartment unless they are secured. You will find further information under “Transporting156” ( page 156) and “Features164” ( page 164) in the “Controls in detail” section. An unsecured or incorrectly positioned load increases the risk of injury to occupants, particularly children, in the event of: eting sound can be heard to indicate taht the special seat belt retractor is activated. The belt is now locked.
Safety Occupant safety Warning 2 G If the child restraint system is not installed correctly on a suitable vehicle seat, the child may not be restrained in the event of an accident or sudden braking and may be seriously or fatally injured. For this reason, always observe the installation instructions issued by the child restraint system manufacturer and the intended use for the child restraint system when fitting it. It is advisable to install the child restraint system on one of the rear seats.
Safety Occupant safety on the outside left on rear bench seats with 2 seats A statement by the child restraint manufacturer of compliance with this standard can be found on the instruction label on the restraint and in the instruction manual provided with the restraint. When using any infant or child restraint system, make sure to carefully read and follow all manufacturer’s instructions for installation and use.
Safety Occupant safety Warning 2 G If the child restraint system has not been installed correctly on a suitable vehicle seat, the child cannot be restrained in the event of an accident or sudden braking and could be seriously or fatally injured. You must therefore observe the installation instructions issued by the child restraint system manufacturer when installing a child restraint system.
Safety Occupant safety Warning Slide head restraint 1 upward. G Guide TopTether belt 4 under head restraint 1 from the front and between the two head restraint bars. Do not expose child restraint systems to direct sunlight. Metallic parts of the child restraint system could heat up, for example, and the child could burn him/herself on the hot parts. Hook TopTether hook 3 into TopTether anchorage 2 on the feet of the bench seat.
Safety Driving safety systems Driving safety systems In this section, you will find information about the following driving safety systems: 2 ABS (Antilock Brake System) BAS (Brake Assist) ESP® (Electronic Stability Program) ASR (acceleration skid control) EBV (electronic brake force distribution) i The maximum effect of ABS, BAS, ESP®, ASR and EBV can only be achieved if you: always drive with the correct tire pressures adjusted according to the load ( page 210) use winter tires (M+S ti
Safety Driving safety systems Braking If ABS intervenes during braking, you will feel the steering wheel vibrate gently and the brake pedal pulsate. If ABS intervenes: Brake Assist (BAS) Continue to depress the brake pedal firmly until the braking situation is over. For full brake application: Depress the brake pedal with maximum force. Warning braking and the stopping distance may increase. If ABS is deactivated due to a malfunction, BAS is also deactivated.
Safety Driving safety systems Warning 2 G Proceed as follows if the v warning lamp in the speedometer flashes: Do not deactivate ASR under any circumstances. Only depress the accelerator pedal as far as necessary when pulling away. Adapt your driving style to suit the prevailing road and weather conditions. Otherwise, the vehicle could begin to skid. ESP® cannot reduce the risk of an accident if you drive too fast. ESP® is unable to override the laws of physics.
Safety Driving safety systems Activating/deactivating ASR ASR is automatically activated as soon as the engine is switched on.
Safety Driving safety systems Electronic brake force distribution (EBV) 2 EBV monitors and regulates the brake pressure at the rear wheels to improve driving stability during braking. Warning G If EBV malfunctions, the brake system is still available with the full brake boosting effect. However, the rear wheels may lock, for example if the brakes are applied with maximum force. You could then lose control of the vehicle and cause an accident.
Safety Anti-theft systems Anti-theft systems Immobilizer The immobilizer prevents the vehicle from being started without the correct key. A visual and audible alarm is triggered if the alarm system is enabled and: When leaving the vehicle, always take the key or remote keyless entry transmitter with you and lock the vehicle.
Safety Anti-theft systems Tow-away protection* A visual and audible alarm is triggered if the inclination of the vehicle changes while tow-away protection is enabled. 2 i The tow-away protection alarm is triggered shortly before the wheel leaves the ground if the vehicle is being jacked up on one side, for example. Deactivating the tow-away protection for transportation Deactivate tow-away protection if the vehicle is transported or loaded onto another vehicle. This will prevent false alarms.
Safety Anti-theft systems Interior motion sensor* If the anti-theft alarm system is enabled and the vehicle is locked, a visual and audible alarm is triggered if one of the side windows or the rear window on your vehicle is smashed and someone reaches into the interior, for example. Deactivating the interior motion sensor Press button 1. Deactivate the interior motion sensor if people or animals remain in the locked vehicle. This will prevent false alarms.
Controls in detail Controls in detail Opening and closing ............52 Key positions ............67 Seats ............68 Steering wheel adjustment ............76 Lighting ............77 Instrument cluster ............84 Operating system without steering wheel buttons ............87 Operating system with steering wheel buttons* ............89 Driving and parking ......... 110 Automatic transmission ......... 121 Good visibility ......... 125 Tempmatic ......... 129 Auxiliary heating/ventilation* .........
Controls in detail Opening and closing Opening and closing Remote control with key Included with your vehicle are 2 or 4* remote keyless entry transmitters with a folding mechanical key. i 3 USA only: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Controls in detail Opening and closing Warning i G To prevent theft, only use the remote control in the immediate vicinity of the vehicle. In an emergency, the driver’s door and rear door can also be unlocked manually using the key. Do not leave children unsupervised in the vehicle, even if they are secured by a child restraint system.
Controls in detail Opening and closing Locking and unlocking the vehicle with the remote control Unlocking the driver's door Press the Πbutton. The turn signals flash once. 3 The anti-theft alarm system (ATA)* is deactivated. i If you unlock the vehicle using the key and do not open a door within 40 seconds, the vehicle locks again automatically. Unlocking the vehicle centrally Unlock the driver's door. Press the Πbutton within 2 seconds again. The turn signals flash once.
Controls in detail Opening and closing The alarm can be disabled in the following ways: Press the Œ button on the remote control. N72.10-2147-31 or Opening the driver’s or co-driver’s door from the inside You can open the driver’s/co-driver’s door from the inside at any time, even if it is locked. Insert the key into the ignition lock. 3 Locking the vehicle Rear door 1 To lock 2 To unlock Insert the key all the way into the door lock and turn it in direction 2. The door is unlocked.
Controls in detail Opening and closing i Sliding door Warning 3 G If the vehicle is parked on an incline, the sliding door may move of its own accord if it is open but not engaged. You or others could be trapped. When you open/close the sliding door, you can also detent it around half way so that it is not always necessary to open the door to the end stop to get in and out of the vehicle. The intermediate detent does not fully engage the sliding door.
Controls in detail Opening and closing To close: press button 2 to release the sliding door from its detent and, holding door handle 3, pull the door firmly towards the front until it engages. To lock: press locking knob 4 down. Only this sliding door is locked. Electric closing aid* Electric sliding door* Depending on the vehicle’s equipment, there are electric sliding doors on the left and/or right-hand side. Opening/closing using the switch Observe the notes on anti-trap protection ( page 60).
Controls in detail Opening and closing The sliding door unlocks. N72.16-2119-31 3 Sliding door switch in the doorway 3 To open/close the sliding door i On vehicles with a partition, the switch is located on the partition near the doorway level with the inside door handle. To open the sliding door: briefly press lower part 2 of the switch on the center console. The indicator lamp in the switch flashes. The sliding door unlocks and opens, and a signal sounds. or Briefly press switch 3 in the doorway.
Controls in detail Opening and closing Opening/closing using the inside and outside door handles Briefly press button 1 or pull outside door handle 2. Observe the notes on anti-trap protection ( page 60). The sliding door opens or closes and a signal sounds. N72.16-2136-31 Press button 1 again or pull outside door handle 2 again. N72.16-2118-31 The sliding door stops. Opening/closing with the remote control Press and hold the button for more than half a second.
Controls in detail Opening and closing Anti-trap protection Warning 3 G The anti-trap protection function does not eliminate the possibility of fingers or other parts of the body being trapped against the door frame and therefore does not eliminate the risk of injury. Always make sure that nobody is within the operating range of the sliding door. If the sliding door is obstructed during the opening procedure, it moves back in the opposite direction slightly and stops.
Controls in detail Opening and closing Opening the left-hand rear door from the outside Opening the rear doors to an angle of 270° Warning G Make sure that the traffic area is clear when opening the rear doors beyond 90°. You could otherwise injure yourself and others. 3 1 Release lever 1 Door retainer Make sure that the right-hand rear door is open and engaged. Open the rear door to an angle of approximately 45°. Pull release lever 1 in the direction of the arrow.
Controls in detail Opening and closing i 3 If you prefer to keep door retainer 1 ( page 61) out of the loading area when loading the vehicle, you can swivel it 180° against the spring pressure and onto the door, where it engages. The door retainer then remains in this position and no longer returns to its original position. Before closing the door, release door retainer 1 from the detent and return it to its original position.
Controls in detail Opening and closing Warning G Make sure that nobody can become trapped as you close the rear door. To close: make sure that the left-hand rear door is closed. Pull the right-hand rear door firmly closed by the door handle. To lock: slide catch 2 to the right. Only the rear door is locked. The white marking is no longer visible.
Controls in detail Opening and closing The indicator lamp in the central locking switch indicates when the sliding doors and the rear door are locked. You can determine whether the driver's door or codriver's door is locked or unlocked by the position of the locking knobs. 3 Locking the entire vehicle Press upper part 1 of the switch when the doors are closed. The indicator lamp in the switch comes on.
Controls in detail Opening and closing !CAUTION i If your vehicle is centrally locked, this could hinder rescue operations from the outside in the event of an accident. If activated, automatic locking is deactivated if the vehicle is unlocked or locked using the central locking switch. When the automatic locking when driving function is activated, there is a risk of being locked out if the vehicle is pushed or towed.
Controls in detail Opening and closing Deactivating the automatic locking when driving function for the sliding doors and the rear door Operating the partition sliding door from inside the cab Operating the partition sliding door from inside the load compartment 1 To close 2 To open 3 To unlock 1 To open 2 To close 3 To unlock To open: turn the key counterclockwise 3. To open: press the lever to the right 3. Close all the doors.
Controls in detail Key positions Key positions i The key can only be removed from position 0. Also observe the notes in the “Driving and parking” section ( page 110). To unlock the steering, turn the steering wheel slightly while turning the key to position 1. 0 To remove the key, to lock the steering wheel 1 To unlock the steering wheel (power supply for some consumers, e.g.
Controls in detail Seats Driver’s and co-driver’s seats Warning 3 Observe the following points: G Only adjust the seats when the vehicle is stationary and the handbrake is applied. You could otherwise lose control of the vehicle as a result of the seat moving and cause an accident. Warning G Position the backrest as vertically as possible and sit upright. Avoid seat positions that do not allow the seat belt to be routed correctly.
Controls in detail Seats Standard, comfort* and suspension seats* i Different settings are possible, depending on the seat version. Seat fore-and-aft adjustment Pull lever 1 up. Slide the seat forwards or backwards until you can reach the pedals and depress them. Release lever 1. Slide the seat forwards or backwards slightly until it engages audibly. Backrest adjustment Turn thumbwheel 3 forward.
Controls in detail Seats Seat suspension adjustment* The seat suspension must be adjusted to your body weight. Relieve the load on the seat. Select your body weight 88 to 165 lbs (40 to 120 kg) using thumbwheel 6 for optimal seat suspension. 3 The seat suspension becomes harder as the load on the seat increases. Vertical lock* If the seat bounces up and down frequently, you can engage the seat in its lowest position. Turn lever 7 downward.
Controls in detail Seats The seat release lever is located behind the seat between the seat backrest and the seat base. Warning G Folding the seat cushion forward You could knock yourself against the unprotected pivoting frame if the seat is opposite of the direction of travel and pushed right back in a longitudinal direction. 3 Therefore, center the seat above the seat base whenever you leave it. Point out this danger to passengers.
Controls in detail Seats Positioning the seat cushion Fold the seat cushion back. Slide the seat cushion under the backrest and into rear anchorage 2. Fold the seat cushion down. 3 Press the front of the seat cushion down until it engages in front anchorage 1. Armrests* Adjusting the armrest angle Fold the armrest up by an angle of more than 45° to unlock it 2. Fold the armrest forward to the stop 3. There are six closely spaced positions in which the armrest can engage if you raise it.
Controls in detail Seats Removing the head restraints Pull the head restraint up as far as it will go. Seat heating* The switches for the driver’s and codriver’s seat are on the center console. Press release button 1 and pull the head restraint out. To switch off: press upper part of the & switch again. The indicator lamp in the switch goes out. Rapid heating Installing the head restraints To switch on: press lower part of the switch.
Controls in detail Seats Folding seat* The folding seat is on the co-driver’s side. Warning G When folding down the seat cushion, make sure that nobody can become trapped. The risk of injury to the co-driver is increased in the event of sudden steering movements or an accident if there is a key inserted in the partition sliding door lock. 3 Remove the key from the partition sliding door before using the folding seat.
Controls in detail Seats i Installing the rear bench seat Do not exceed the maximum permissible number of seats for passenger vans. Slide the rear bench seat forward until you hear the locking mechanisms engage. Check levers 1 on the bench seat feet. All levers 1 must be parallel to the vehicle floor. Removing the rear bench seat The locking lever is located underneath the bench seat, on the feet of the bench seat.
Controls in detail Steering wheel adjustment Steering wheel adjustment Warning 3 G The lever for adjusting the steering column is under the steering wheel. Swing lever 3 down to the stop. The steering wheel is unlocked. Only adjust the steering wheel when the vehicle is stationary. Only drive with the steering wheel locked in position. Move the steering wheel to the desired position.
Controls in detail Lighting Legal requirements may impose variations in certain countries. i Light switch The light switch is located between the driver’s door and the steering wheel. If you are traveling in countries where vehicles are driven on the opposite side of the road to that in which the vehicle is registered, you must have the headlamps: Turn light switch to B. The B indicator lamp in the instrument cluster lights up.
Controls in detail Lighting Turn key to position 1 in ignition lock ( page 67). Turn light switch to B. Press combination switch forward 1. The indicator lamp A in the instrument cluster lights up. 3 Headlamp flasher Turn key to position 1 in ignition lock ( page 67). Pull combination switch briefly in direction 2. Constant headlamp mode* On vehicles with steering wheel buttons, you can set constant headlamp mode ( page 102).
Controls in detail Lighting Switching on the rear foglamp Front foglamps*/rear foglamp Make sure that the parking lamps or low-beam headlamps are switched on. i Foglamps will operate with the parking lamps and/or the low beam headlamps on. Foglamps should only be used in conjunction with low beam headlamps. Consult your State or Province Motor Vehicle Regulations regarding permissible lamp operation. i When the light switch is set to U, you cannot switch on the front or rear foglamps.
Controls in detail Lighting Push combination switch up 1 or down 2 until it engages. The combination switch moves back automatically if the steering wheel is turned sufficiently. Hazard warning lamps The hazard warning lamps still operate if the ignition is switched off and the key is removed. The switch is located on the center console. i 3 To indicate minor directional changes such as changing lanes, press the combination switch only to point of resistance and release.
Controls in detail Lighting Front interior lighting with overhead control panel* Automatic control Manual control The front interior lighting (but not the rear interior lamps) comes on if you: Press button 6. Front interior lamps 4 come on. unlock the vehicle Press button 6 again. Front interior lamps 4 switch off. open a door remove the key from the ignition lock The front interior lighting switches off again automatically. To switch off: press button 5.
Controls in detail Lighting Rear interior lighting Switching the standard rear interior lighting on/off 3 On panel vans/crewbuses equipped with the standard rear interior lighting, the switch for the rear interior lighting is on the rear lamp in the load/passenger compartment. i Rear interior lighting master control switch The rear interior lamps switch off automatically after 20 minutes if a sliding door or rear door is open.
Controls in detail Lighting i The rear interior lamps switch off automatically after 20 minutes, even if the switches on the rear interior lamps ( page 82) are in the On position 1. If you wish to reactivate the rear interior lamps, you must: open a door switch on the ignition again set the rear interior lighting master control switch to position 2 again.
Controls in detail Lighting Instrument cluster i Do not hang any objects (e.g. coats) in the load compartment. This will help to prevent the motion detector from inadvertently switching on the rear interior lamps. 3 You will find a full overview of the instrument cluster in the “At a glance” section ( page 14).
Controls in detail Lighting Warning G No messages can be displayed if the instrument cluster and/or the display is malfunctioning. You will not then be able to see information about the vehicle status, such as speed and outside temperature, warning and indicator lamps, malfunction and warning messages or the malfunction of systems. Handling characteristics may be affected.
Controls in detail Lighting Fuel gauge Resetting the trip meter Vehicles with steering wheel buttons*: Make sure that the display is showing the trip meter ( page 93). Keep reset button pressed until the trip meter is set to 0.0.
Controls in detail Operating system without steering wheel buttons Operating system without steering wheel buttons The operating system is activated as soon as you switch on the ignition. You may perform the following using the operating system: Call up vehicle information Make settings Warning G The operating system shows the information in the display.
Controls in detail Operating system without steering wheel buttons 3 There may be a short delay before a lower outside temperature is displayed, for example after leaving a garage. There may also be a short delay before a rise in the outside temperature is displayed. This prevents you from seeing a temperature display influenced by heat from the engine when the vehicle is stationary or moving slowly. Setting the date i To return to the standard display: Switch on the ignition ( page 67).
Controls in detail Operating system with steering wheel buttons* Operating system with steering wheel buttons* The operating system is activated as soon as you switch on the ignition. You may perform the following using the operating system: Call up vehicle information Steering wheel with buttons You can control the display and the settings in the operating system with the buttons on the steering wheel. Make settings Only use the operating system when road and traffic conditions permit.
Controls in detail Operating system with steering wheel buttons* Several functions are combined thematically in the menus. The display changes when you press one of the buttons on the steering wheel. 3 For example, the AUDIO menu contains functions for controlling the radio* or CD player*. You can use a function to call up information or to change the settings for the vehicle.
Controls in detail Operating system with steering wheel buttons* Menu overview This is what the display looks like when you scroll through the menus. The explanations for the individual menus are shown in the following table. 3 N54.32-2282-31 The illustration is an example of the menus on a vehicle with COMAND APS*.
Controls in detail Operating system with steering wheel buttons* The table below shows the menus and the individual functions.
Controls in detail Operating system with steering wheel buttons* i The tabluar overview of the menus contains generic terms which are not always shown in the operating system. The generic term concerned is intended simply to make it easier for you to familiarize yourself with the menus. The operating system displays the new function range directly with the first menu function. With Sound 5/Sound 20, the operating system always shows the AUDIO and TEL (telephone) menus in English.
Controls in detail Operating system with steering wheel buttons* N54.32-2251-31 The temperature displayed may climb to 3 250 °F (120 °C) when the vehicle is being driven in normal conditions and if the coolant contains the correct concentration of corrosion inhibitor and antifreeze. It is acceptable for the coolant temperature to rise to the end of the scale at high outside temperatures and when driving in mountainous terrain.
Controls in detail Operating system with steering wheel buttons* Press the è or ÿ button repeatedly until the settings for the CD being played are displayed. Malfunction memory menu The Malfunction memory menu displays malfunctions that may have occurred. The message in the display depends on whether malfunctions have occurred or not. Warning 1 Current CD (with CD changer) 2 Current track Press the j or k button repeatedly until you have set the desired track.
Controls in detail Operating system with steering wheel buttons* Settings menu The Settings menu has two functions: the To reset: Press reset button for 3 sec. function, with which you can reset all settings to the factory defaults 3 a collection of submenus which you can use to make individual settings for your vehicle Press the è or ÿ button repeatedly until you see the Settings menu in the display.
Controls in detail Operating system with steering wheel buttons* Resetting the functions of a submenu Submenus in the Settings menu You can reset the functions of an individual submenu to the factory defaults. Press the j button. Select a function in a submenu. Press reset button for approximately 3 seconds. You will see the message in the display prompting you to press the reset button once more to confirm. Press You will see the collection of submenus.
Controls in detail Operating system with steering wheel buttons* 3 Instrument cluster ( page 99) Clock/Date ( page 101) Lighting* ( page 102) Vehicle ( page 104) Auxiliary heating* ( page 139) Convenience* ( page 105) Select the unit for the temperature Set the hours (clock) Set constant headlamp mode* Set station selection Select a switchon time Key-dependent settings Select the unit for the speedometer Set the minutes (clock) Switch the locator lighting on or off* Set the windshield
Controls in detail Operating system with steering wheel buttons* Press the æ or ç button to select the unit for all messages in the display: km/h or mph (kilometers or miles per hour). Instrument cluster submenu You can reach the Inst. cluster submenu via the Settings menu ( page 96).
Controls in detail Operating system with steering wheel buttons* 3 Selecting the language Selecting the display for the status line Selecting the unit for the tire pressure Select the Inst. cluster submenu using the æ or ç button. Select the Inst. cluster submenu using the æ or ç button. Select the Inst. cluster submenu using the æ or ç button. Press the j or k button repeatedly until you see the Language message in the display.
Controls in detail Operating system with steering wheel buttons* Clock/Date submenu Setting the hours You can reach the Clock/Date submenu via the Settings menu ( page 96). Select the Clock/Date submenu using the æ or ç button. i The Clock/Date submenu only appears if you do not have COMAND APS* installed. With COMAND APS*, it is only possible to set the time using the audio system. See the separate operating instructions.
Controls in detail Operating system with steering wheel buttons* Setting the day Lighting submenu* Select the Clock/Date submenu using the æ or ç button. You can reach the Lighting submenu via the Settings menu ( page 96). Press the j or k button repeatedly until you see the Date Day message in the display. 3 N54.32-2265-31 Set the day by pressing the æ or ç button. N54.32-2266-31 Function Page Set constant headlamp mode* 102 Set the month by pressing the æ or ç button.
Controls in detail Operating system with steering wheel buttons* Press the æ or ç to select the Lighting submenu. Press the j or k button repeatedly until you see the Hdlmp. mode message in the display. The current setting is highlighted. N54.32-2268-31 Press the æ or ç button to select whether you wish to operate the lighting manually or whether you wish to set constant headlamp mode. i For safety reasons, it is not possible to reset the Hdlmp.
Controls in detail Operating system with steering wheel buttons* Setting the exterior lighting delayed switch-off* Press the æ or ç to select the Lighting submenu. The Headlamps (headlamps delayed switchoff) function enables you to set whether or not the exterior lighting should remain on in the dark after the doors have been closed. Press the j or k button repeatedly until you see the Headlamps message in the display. The current setting is highlighted.
Controls in detail Operating system with steering wheel buttons* N54.32-2271-31 Press the j or k button repeatedly until you see the Wipe sensor message in the display. Convenience submenu* You can reach the Convenience submenu via the Settings menu ( page 96). The current setting is highlighted. Key-dependent settings Press the æ or ç button to select how the radio should tune into a station.
Controls in detail Operating system with steering wheel buttons* Press the æ or ç button to switch key dependence On or Off. i 3 For safety reasons, it is not possible to set the Key function while the vehicle is in motion. You will see the following message in the display: Setting only possible at standstill. Trip computer menu The Trip computer menu displays statistical data for your vehicle. Function Press the è or ÿ button repeatedly until you see the After start message in the display.
Controls in detail Operating system with steering wheel buttons* Consumption statistics after reset Resetting the consumption statistics Press the è or ÿ button repeatedly until you see the After start message in the display. Press the è or ÿ button repeatedly until you see the After start message in the display. Press the j or k button repeatedly until you see the After reset message. Press the j or k button repeatedly until you see the statistics that you want to reset in the display.
Controls in detail Operating system with steering wheel buttons* Switch on the cell phone and audio system or COMAND APS*. The cell phone searches for a network. The display remains blank during this time. Accepting a call See the separate operating instructions. As soon as the cell phone has found a network, you will see the Ready message in the display. Press the s button. Press the è or ÿ button repeatedly until you see the TEL menu in the display.
Controls in detail Operating system with steering wheel buttons* Press the j or k button. The operating system reads the phone book stored on the SIM card or in the phone. This may take more than 1 minute. You will see the Processing message (Sound 20) or Wait... message (COMAND APS*) in the display. Press the j or k button repeatedly until you see the name you are looking for. The stored names are displayed alphabetically from A to Z, or Z to A.
Controls in detail Driving and parking Driving and parking Warning G The movement of the pedals must not be obstructed. The vehicle’s operating and road safety are otherwise jeopardized. 3 Objects could fall and get caught between the pedals if you accelerate or brake suddenly. You will no longer be able to brake or accelerate. You could cause an accident, which could result in injury to yourself and others.
Controls in detail Driving and parking Before starting the engine, make sure that all vehicle occupants are wearing their seat belt correctly ( page 27) and the handbrake ( page 115) is applied. Automatic transmission Gasoline engine Turn the key to position 3 in the ignition lock ( page 67) and release it immediately ("touch-start" function). !CAUTION The engine starts automatically. Do not depress the accelerator pedal when starting the engine.
Controls in detail Driving and parking Pulling away Warning 3 G Do not downshift for additional engine braking on a slippery surface. The drive wheels may lose their grip and the vehicle could skid. !CAUTION Only drive at high speeds once the engine has warmed up. This protects the engine. When driving on slippery surfaces, avoid spinning the drive wheels where possible as this could damage the drive train.
Controls in detail Driving and parking Braking Warning G There is no power assistance for the service brake when the engine is not running. You will need to use significantly more force to brake and could therefore lose control of the vehicle and cause an accident. Never switch off the engine while driving. Do not accelerate to prevent your vehicle from rolling backwards on an uphill gradient. Instead, you should either use the handbrake or depress the brake pedal.
Controls in detail Driving and parking Parking Warning 3 Warning G Only remove the key from the ignition lock when the vehicle is stationary, since it is not possible to steer the vehicle with the key removed. Always apply the handbrake after parking the vehicle. Never leave children unsupervised in the vehicle. They could release the handbrake. This could lead to a serious or fatal accident. G Always switch off the engine and apply the handbrake before leaving the vehicle.
Controls in detail Driving and parking Handbrake Warning G Never leave children unsupervised in the vehicle. They could release the handbrake. This could lead to a serious or fatal accident. The handbrake is located between the driver’s seat and the co-driver’s seat. Applying the handbrake Emergency braking Pull lever 1 up as far as the last detent. The 7 indicator lamp in the instrument cluster lights up while the engine is running.
Controls in detail Driving and parking Stopping the engine !CAUTION 3 If the coolant temperature is raised, e.g. following driving in mountainous terrain, run the engine at idling speed for a further 1 or 2 minutes before you switch off the engine. This allows the coolant temperature to return to normal again. i When parking on steep uphill or downhill gradients, turn the front wheels towards the curb. Apply handbrake ( page 115). Move selector lever to P.
Controls in detail Driving and parking Overrun cut-off Driving on flooded roads The gasoline/diesel supply is cut off if the driver's foot is completely removed from the accelerator pedal when the engine is overrunning at engine speeds outside of the idling control range.
Controls in detail Driving and parking Warning 3 G If you feel a sudden significant vibration or ride disturbance, or you suspect that possible damage to your vehicle has occurred, you should turn on the hazard warning flashers, carefully slow down, and drive with caution to an area which is a safe distance from the road. Inspect the tires and the vehicle undercarriage for possible damage.
Controls in detail Driving and parking Tire traction Tire grip is greatly reduced on a wet, snow covered or icy road. Speed and driving style must therefore be adapted to suit road conditions. The safe speed on a wet, snow covered or icy road is always lower than on a dry road. In winter, install M+S radial tires with a minimum tread depth of approximately 1/ 6 in (4 mm) on all wheels to ensure normal balanced handling characteristics.
Controls in detail Driving and parking Alignment and balance Coolant temperature Poor suspension alignment may result in: During severe operating conditions and stop-and-go city traffic, the coolant temperature may rise close to approximately 250 °F (120 °C). Fast tire wear Uneven tire wear, such as feathering and one-sided wear Vehicle pulling to the left or right 3 Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition.
Controls in detail Automatic transmission Automatic transmission Gearshift pattern If the operating or driving conditions change, the automatic transmission reacts by adjusting the gearshift program. When the selector lever is in position D, you can influence the gearshifts made by the automatic transmission by: The individual gears are selected automatically.
Controls in detail Automatic transmission ë Neutral No power is transmitted from the engine to the drive wheels. Releasing the brakes will allow you to move the vehicle freely, e.g. by pushing or towing. Do not move the selector lever to N while the vehicle is in motion. The automatic transmission could otherwise be damaged. 3 If ASR is deactivated or ESP® has malfunctioned: only move the selector lever to N if the vehicle is in danger of skidding, e.g. on icy roads.
Controls in detail Automatic transmission Selecting the ideal shift range Press and hold the selector lever towards D–. The automatic transmission will shift to a range which allows easy acceleration and deceleration. To do this, the automatic transmission will shift down one or more gears. Shift ranges When the selector lever is in position D you can restrict or derestrict the shift range for the automatic transmission.
Controls in detail Automatic transmission Stopping Trailer towing If you are only stopping briefly: Run the engine in the moderate engine speed range on steep uphill gradients. leave the selector lever in the drive position secure the vehicle against rolling away using the brake pedal 3 Maneuvering Maneuvering in a tight space: Control the speed by braking carefully. Accelerate only slightly and avoid jolting. i For rapid maneuvering (e.g.
Controls in detail Good visibility Good visibility Mirrors Before starting off, adjust the rear-view mirror and the exterior mirrors in such a way that you can get a good overview of road and traffic conditions. Rear-view mirror* Adjust the rear-view mirror manually. Setting the rear-view mirror to antidazzle mode Exterior mirrors Adjust the exterior mirrors manually. Warning G The exterior mirrors reduce the size of the image. Objects therefore appear further away than they really are.
Controls in detail Good visibility Windshield wipers The combination switch is located on the left of the steering wheel. N54.25-2923-31 3 !CAUTION Vehicles with rain sensor*: Switch off the windshield wipers in dry weather conditions, otherwise dirt on the surface of the rain sensor or optical effects can cause inadvertent wiper sweeps. This could damage the wiper blades or scratch the windshield.
Controls in detail Good visibility Wiping with washer fluid Press the combination switch beyond the pressure point in the direction of arrow 1. Rear window wiper* The switch is in the combination switch on the left of the steering wheel. Switching on intermittent wipe Turn switch 1 to 3. Switching off intermittent wipe The windshield wiper will wipe with windshield washer fluid. Turn switch 1 to 4.
Controls in detail Good visibility Warning 3 G To switch on: press upper part of the P switch. The indicator lamp in the switch comes on. Clear ice or snow from the windshield before commencing a journey. Iced-up windows restrict your view. You could cause an accident and endanger yourself and others. Do not start the vehicle if the windows are iced up, fogged up or covered in snow. To switch off: press upper part of the P switch again.
Controls in detail Tempmatic Tempmatic 3 N83.
Controls in detail Tempmatic Function 1 Side window defroster vents Page 135 2 Thumbwheel for air vents 3 Side air vents 3 4 Thumbwheel for side air vents and defroster vents 135 5 Swiveling center air vents The combination filter removes most dust particles, pollen and unpleasant odors from the outside air. The interval for replacing the filter depends on environmental factors, e.g. high air pollution. The interval may be shorter than that indicated in the Service Booklet.
Controls in detail Tempmatic i Function If the vehicle interior has been heated up, ventilate the vehicle before starting your journey or briefly switch to air-recirculation mode for faster cooling. Keep the air inlet on the hood free from ice and snow. Position the sliders for the center air vents in the central position to provide practically draft-free ventilation.
Controls in detail Tempmatic Basic setting Ventilation This setting rapidly ventilates the vehicle interior. N83.40-2060-31 3 Heating Turn temperature selector control 1 ( page 131) to the lowest setting (maximum cooling). Set airflow control 2 ( page 131) as required, but do not turn the control below the second speed. The recommended setting for the target temperature is 72.0 °F (22.2 °C) under normal conditions, to which Tempmatic adjusts as rapidly and as comfortably as possible.
Controls in detail Tempmatic Setting the air distribution The air distribution is set using the air distribution control in the control panel ( page 131). Setting the airflow The markings on the air distribution control have the following meanings: N83.00-2125-31 Mark Meaning h Air from the air vents ÔP Air to the windshield Air from the air vents 1 Airflow control To increase: press the Q airflow control. To reduce: press the control.
Controls in detail Tempmatic To switch off: press the Ä switch again. The indicator lamp in the switch goes out. i 3 Air-recirculation mode is automatically switched off after about 10 to 30 minutes, depending on the outside temperature. Residual heat mode The engine stores residual heat after long periods of driving. You can use the residual heat of the engine to heat the stationary vehicle for a further 30 minutes.
Controls in detail Tempmatic The indicator lamp in the switch comes on. Turn airflow control 2 ( page 131) to a higher blower speed, but do not turn the control below second speed. Turn temperature selector control 1 ( page 131) to a higher temperature. Turn air distribution control 5 to ‚ P. Defrosting The following settings can be used to clear the windshield and the side windows, e.g. if covered with frost. Set temperature selector control 1 to P. Turn airflow control 2 to fourth speed.
Controls in detail Tempmatic Ventilated glove box* The glove box can be ventilated when Tempmatic is switched on, e.g. to cool its contents. Setting the airflow Air conditioning in the rear* The airflow is set using the airflow control for the rear compartment. To increase: press the Q airflow control. N83.60-2009-31 To reduce: press the control. 3 airflow The display next to the airflow controls indicates the speed of the airflow.
Controls in detail Tempmatic To reduce: turn the temperature selector control counterclockwise. Air vents in the roof air duct Adjustable air vents are integrated in the roof air duct. Heater booster function* The fuel-fired heater booster system heats the vehicle interior as quickly as possible while the engine is running. N54.25-2927-31 i The auxiliary heating automatically switches to heater booster mode after the engine is started.
Controls in detail Tempmatic To switch on: press the switch ³. The indicator lamp in the switch comes on. i 3 If you switch off the engine without switching off the heater booster function, the system will be switched on the next time the engine is started (memory function). To switch off: press the ³ switch again. The indicator lamp in the switch goes out. The heater booster function operates for around a further 2 minutes and then switches off automatically.
Controls in detail Auxiliary heating/ventilation* Auxiliary heating/ventilation* The auxiliary heating heats or ventilates the interior to a temperature that you have set. The auxiliary heating can be operated with the engine switched on or off. The auxiliary heating is equipped with a water heater. Warning G Exhaust fumes are produced while the auxiliary heating is in operation. For this reason, switch off the auxiliary heating in enclosed spaces without an extraction system, e.g. a garage.
Controls in detail Auxiliary heating/ventilation* You can switch the auxiliary heating/ ventilation on and off immediately using: the auxiliary heating/heater booster switch ( page 140) The red indicator lamp in the switch comes on. Operation using the switch The switch for the auxiliary heating/ ventilation is between the light switch and the steering wheel. i You cannot use the auxiliary ventilation to cool the vehicle interior to a lower temperature than the outside temperature.
Controls in detail Auxiliary heating/ventilation* Operation using the remote control* The remote control has a maximum range of approximately 600 meters. The range may be reduced by: sources of interference solid objects between the remote control and the vehicle the remote control being in an unfavorable position transmitting from an enclosed space You can use up to 4 remote control units on the vehicle. To switch the auxiliary heating on: press button 2. Indicator lamp 1 lights up briefly.
Controls in detail Auxiliary heating/ventilation* Selecting a switch-on time You can use the operating system to define up to 3 switch-on times, one of which can be selected to switch on the auxiliary heating/ventilation. 3 Operating system without steering wheel buttons Switch on the ignition ( page 67). Press the ö switch. The ö symbol in the display flashes. or Press the menu button on the instrument cluster repeatedly until the ö symbol in the display flashes.
Controls in detail Auxiliary heating/ventilation* Press the è button. The switch-on time is selected. The yellow indicator lamp in the ö switch comes on. i If you turn the key to position 0 in the ignition lock, the yellow indicator lamp in the ö switch goes out after 30 minutes. The red indicator lamp in the ö switch comes on when the auxiliary heating switches on. Press the reset button on the instrument cluster to set the selected switchon time.
Controls in detail Open air Open air To close: pull and hold switch 1 or 2 until the window has reached the desired position. Side windows You can open and close the side windows electrically. The switches for all side windows are located on the door control panel. 3 Warning Resetting the side windows The side windows must be reset if the battery has been disconnected: G Make sure that nobody can become trapped as you close a side window.
Controls in detail Open air Switch on the ignition ( page 67). Sliding sunroof* Warning Press the sliding sunroof switch in the desired direction as far as the first pressure point. G Release the sliding sunroof switch when the desired position has been reached. Make sure that nobody can become trapped as you close the sliding sunroof. The glass may shatter in the event of an accident.
Controls in detail Open air Resetting the sliding sunroof The sliding sunroof must be reset after: the sunroof has been closed manually using the emergency operation key ( page 304) the sunroof has opened with a jerk 3 Roof ventilator in the load compartment* The roof ventilator can be used to ventilate or remove air from the load compartment. The switch is between the light switch and the steering wheel. a malfunction Switch on the ignition ( page 67).
Controls in detail Driving systems Driving systems Driving systems which may form part of your vehicle are described on the following pages: Cruise control* ( page 147), which you can use to control the speed of your vehicle Parktronic system*, which is an aid for parking and maneuvering ( page 150) Reverse warning feature*, which helps you ensure the safety of other road users ( page 153) ESP®, The ABS, BAS, ASR and EBV driving safety systems are described in the "Safety and Security" section (
Controls in detail Driving systems Storing the current speed i 3 Cruise control may be unable to main- Accelerate/decelerate the vehicle to the desired speed. tain the stored speed on uphill or downhill gradients. The stored speed is Move the cruise control lever briefly resumed if the gradient evens out and upward 1 or downward 3. the vehicle’s speed has not fallen below Release the accelerator pedal. 20 mph (30 km/h). Cruise control is activated. Cruise control lever The current speed is stored.
Controls in detail Driving systems Release the cruise control lever. Setting the speed Warning The current speed is stored. G The rate at which you increase the speed in 1 mph increments (1 km/h increments) may be faster than your vehicle is able to accelerate. Your vehicle may then continue to accelerate up to the newly set speed even after you have released the cruise control lever. Only increase the speed if the current situation is appropriate to do so.
Controls in detail Driving systems Parktronic system (PTS)* Warning G Parktronic is only an aid and may not detect all obstacles. This system does not relieve you of the need to pay attention. 3 You are always responsible for safety and must continue to pay attention to your immediate surroundings when parking and maneuvering. Otherwise, you could endanger yourself and others. Warning G Make sure that no persons or animals are in the maneuvering range of the vehicle. They could otherwise be injured.
Controls in detail Driving systems Front sensors Center about 39 in (100 cm) Corners about 26 in (65 cm) Rear sensors Center about 71 in (180 cm) Corners about 39 in (100 cm) Minimum distance Center about 12 in (30 cm) Corners, front about 10 in (25 cm) Corners, rear about 12 in (30 cm) If an obstacle is within this range, all segments of the warning displays light up and you will hear an audible warning tone.
Controls in detail Driving systems The warning displays for the rear left and right-hand sides are in the exterior mirror concerned. !CAUTION From the: There is a malfunction if only the red segments of the warning display light up ( page 262). sixth segment, an intermittent warning tone sounds for approximately 2 seconds The selector lever position determines whether the front and/or rear area is monitored. 3 seventh segment, a continuous warning tone sounds.
Controls in detail Driving systems Switching Parktronic on/off Trailer towing You can switch Parktronic on and off manually. If you attach a trailer, Parktronic is deactivated for the rear area as soon as you make the electrical connection between your vehicle and the trailer. The switch is located on the center console. N54.25-2922-31 Reverse warning feature* On vehicles with a reverse warning feature, a warning signal sounds when reverse gear is engaged to alert other road users.
Controls in detail Operating the vehicle Operating the vehicle Operating speed governor (ADR)* When activated, the operating speed governor (ADR) automatically increases the engine speed to a preset or adjustable operating speed ( page 155). 3 Activating/deactivating ADR The switch is between the light switch and the steering wheel. To switch off: press lower part 2 of the switch with the engine running. i The idle speed of the engine automatically increases after a cold start.
Controls in detail Operating the vehicle Adjustable operating speed* Adjusting the operating speed Switch on ADR ( page 154). To increase: press upper part 1 of the switch. or N54.25-2933-31 On vehicles with cruise control*, press the cruise control lever* up ( page 148). i The idle speed of the engine automatically increases after a cold start. You can only reduce the operating speed to the current idle speed. 3 To reduce: press lower part 2 of the switch.
Controls in detail Transporting Transporting Loading guidelines Warning 3 G Secure and position a load as described in the loading guidelines. Otherwise, the load could slide or be thrown around in the event of strong braking maneuvers, sudden changes of direction or poor road conditions, thereby injuring you or others. The same applies to dismantled seats if left inside the vehicle. Please note that loads increase the risk of injury during an accident even if you comply with all loading guidelines.
Controls in detail Transporting Before loading During loading Checks after loading Check the tire pressures and correct them if necessary ( page 213). Observe the maximum permissible axle loads and permissible gross weight for the vehicle. Securing a load: before each journey and at regular intervals during longer journeys, check whether the load is properly secured and take additional securing measures, if necessary. Clean the load compartment floor.
Controls in detail Transporting Load distribution The load's overall center of gravity should be as low and central as possible, between the axles near the rear axle. !CAUTION 3 Excessive loads on individual points of the load compartment floor or load surface have a negative effect on handling characteristics and could damage the floor covering. For crewbus models: Always transport loads in the load compartment. Always place loads flush against the seat backrests of the rear bench seat.
Controls in detail Transporting Secure tilt and tip-resistant loads in all directions by using the lashing points or lashing eyes and load rails in the load compartment or on the load surface, according to your vehicle's equipment. Only use lashing materials that have been tested according to valid standards, such as lashing nets and straps. 3 Always use the lashing points closest to the load for securing it in place and place padding around sharp edges.
Controls in detail Transporting Warning 3 G Do not carry out any modifications or repairs to the lashing points, the lashing eyes or the lashing materials. The load or the lashing points could accidentally come loose and cause serious injury to you or others as well as damage to property. Distribute loads evenly between the lashing points or lashing eyes. Observe the loading guidelines. i Loose loads should be secured with an approved lashing net or tarp.
Controls in detail Transporting Mounting lashing points for load rails* i Warning Securing loads to the load compartment floor is only recommended for lightweight loads and should be reinforced by using anti-slip mats. Warning If the lashing eye is not firmly anchored in the load rail, the lashing eye may slip or snap out of the load rail in the event of sudden braking or an accident.
Controls in detail Transporting Carrier systems It is possible to mount a roof rack if your vehicle is equipped with securing rails on the roof. Warning G Handling and braking characteristics may change when you have mounted carrier systems on the vehicle. You could endanger yourself and others. Observe the manufacturer’s installation instructions. An incorrectly secured carrier system or load could: 3 come loose fall off and thereby endanger yourself and others.
Controls in detail Transporting !CAUTION If you wish to retrofit securing rails, have them installed at a qualified specialist workshop which has the necessary specialist knowledge and tools to carry out the work required. You could otherwise damage the vehicle. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. Trailer towing Observe the instructions in the “Operation” section ( page 175).
Controls in detail Features Features Storage compartment above the roof trim* Interior storage compartments Warning 3 G Only load the storage compartments in such a way that occupants cannot be injured by their contents in the event of an accident, braking or a sudden change in direction. !CAUTION It is permissible to load the right and left-hand storage compartments up to a maximum of 5.5 lbs (2.5 kg) each. 164 You can use these storage compartments for the safe storage of small and light items.
Controls in detail Features Glove box To open: pull glove box handle 1 in the direction of the arrow. Storage compartments on the dashboard 3 1 Glove box handle 2 Locked* 3 Unlocked* i You can lock and unlock the glove box using the key*. 4 Cards holder 5 Pen holder To close: fold the cover upwards and push against it until it engages in place.
Controls in detail Features Eyeglasses compartment The eyeglasses compartment is located in the overhead control panel. Folding table in the backrest* 3 Covered storage compartment above the center console* 1 Folding table 1 Cover 2 Release handle Pull release handle 2. Cover 1 swings upwards. i The cover on the storage compartment must remain closed while the vehicle is in motion. Close cover 1 and engage it. 166 1 Cover To open: press cover 1 of the eyeglasses compartment.
Controls in detail Features Cup holders in the front Cup holders Warning G Keep the closeable cup holders closed while the vehicle is in motion and do not leave drinks in the cup holders.
Controls in detail Features Place the container in cup holder 5. Press clamping arm 6 onto the container. Cup holders in the rear The cup holders in the rear are located under the seats. 3 Pull out ashtray compartment 1 by recess 2. Ashtray Warning G Switch off the engine and apply the handbrake before removing the ashtray to empty it. Otherwise, you could accidentally put the vehicle in gear. The ashtray is located in the ashtray compartment in the center console.
Controls in detail Features Ashtray in the passenger compartment* The ashtrays are located on the right-hand and left-hand side in the side trims. Cigarette lighter The cigarette lighter is located next to the ashtray in the ashtray compartment in the center console. Warning G Only hold the hot cigarette lighter by its knob. Otherwise, you may burn yourself. Remove the cigarette lighter if children are traveling with you. They could injure themselves on a hot cigarette lighter or start a fire.
Controls in detail Features Paper holder The paper holder is on the control panel for the air-conditioning system. 12 V socket The 12 V sockets for accessories are on the bottom of the center console (12 V, 25 A) on the inside of the driver's seat base (12 V, 15 A) 3 N68.00-2425-31 in the corner trim next to each rear door in the passenger compartment (12 V, 15 A) in the load compartment next to the rear door on the left-hand side (12 V, 15 A)*.
Controls in detail Features Telephone* Telephones may only be used inside the vehicle if they are connected to a separate exterior antenna of a type tested and approved by the manufacturer. Warning G You must observe the legal requirements for the country in which you are driving when operating a cell phone in the vehicle. If it is permitted to operate a cell phone while the vehicle is in motion, you must only operate it when road and traffic conditions permit.
Operation The first 1000 miles (1,500 km) ......... 174 Driving tips ......... 175 Electronic equipment ......... 183 Refueling ......... 184 Engine ......... 185 Battery ......... 195 Battery isolating switch* ......... 197 Tires and wheels ......... 199 Winter driving ......... 234 Maintenance and servicing ......... 237 Cleaning and care of the vehicle .........
Operation The first 1000 miles (1,500 km) You will find detailed information about operating, maintaining and caring for your vehicle in the “Operation” section. If you treat the engine with sufficient care from the very start, it will reward you with excellent performance for a very long time afterward. You should therefore drive at varying road and engine speeds for the first 1000 miles (1500 km). Avoid heavy loads during this time, for example driving at full throttle.
Operation Driving tips Driving tips Information is available about driving in winter and with snow chains ( page 236). Rail transport Transporting your vehicle by rail may be subject to certain restrictions or require special measures to be taken in some countries due to varying tunnel heights and loading standards. You can obtain information at any authorized Sprinter Dealer.
Operation Driving tips Trailer towing Vehicle and trailer weights and ratings Gross Vehicle Weight Rating (GVWR) is the maximum permissible vehicle weight: 8550 lbs (3880 kg) for vehicle model type 2500 9990 lbs (4530 kg), or 11030 lbs (5003 kg) for vehicle model type 3500 4 GVWR (Gross Vehicle Weight Rating) The total allowable weight of the vehicle. All occupants, all cargo, and the trailer tongue load must never exceed the GVWR.
Operation Driving tips Sprinter type GVWR 2500 8550 lbs (3878 kg) 3500 9990 lbs (4531 kg) 3500 11030 lbs (5003 kg) GAWR (FA) GAWR (RA) 3970 lbs (1801 kg) 5360 lbs (2431 kg) 13550 lbs (6146 kg) 5000 lbs (2268 kg) 4080 lbs (1851 kg) 4410 lbs (2000 kg)* 4080 lbs (1851 kg) 4410 lbs (2000 kg)* GCWR GTW 7060 lbs (3202 kg) 15250 lbs (6917 kg) 7720 lbs (3502 kg) 15250 lbs (6917 kg) TWR 500 lbs (227 kg) 7500 lbs (3402 kg) or 750 lbs (340 kg) or 5000 lbs (2268 kg)1 500 lbs (227 kg)1 7500 lbs (3402 k
Operation Driving tips Attaching a trailer Please observe the maximum permitted trailer dimensions (width and length). 4 Most states and all Canadian provinces require safety chains between your tow vehicle and the trailer. The chains should be crisscrossed under the trailer tongue. They must be attached to the hitch receiver, and not to the vehicle’s bumper or axle. Be sure to leave enough slack in the chains to permit turning corners.
Operation Driving tips Always secure items in the trailer to prevent load shifts while driving. Take into consideration that when towing a trailer, the handling characteristics are different and less stable from those when operating the vehicle without a trailer. It is important to avoid sudden maneuvers. The vehicle and trailer combination is heavier, and therefore is limited in acceleration and climbing ability, and requires longer stopping distances.
Operation Driving tips Operating the vehicle outside the USA or Canada If you plan to operate your vehicle in foreign countries, please be aware that: service facilities or replacement parts may not be readily available, 4 unleaded gasoline for vehicles with catalytic converters may not be available; the use of leaded fuels will damage the catalysts, gasoline may have a considerably lower octane rating, and improper fuel can cause engine damage.
Operation Driving tips Regular checks Check regularly, e.g.
Operation Driving tips Emission control Certain systems of the engine serve to keep the toxic components of the exhaust gases within permissible limits required by law. 4 These systems, of course, will function properly only when maintained strictly according to factory specifications. Any adjustments to the engine should therefore be carried out only by an authorized Sprinter Dealer. Engine adjustments should not be altered in any way.
Operation Electronic equipment Electronic equipment Radio, telephone, two-way radio, fax machine and navigation system Warning G Please do not forget that your primary responsibility is to drive the vehicle safely. Only operate the electronic equipment when road and traffic conditions permit. Keep in mind that at a speed of just 30 mph (about 50 km/h), your vehicle travels 44 feet (about 14 m) per second.
Operation Refueling Refueling Warning G The fuel filler flap is next to the driver’s door. You can only open the fuel filler flap when the driver’s door is open. Fuel is highly flammable. Fire, naked flames and smoking as well as the use of auxiliary heaters (sparks) are therefore prohibited when handling fuel. 4 Only fill the tank until the pump nozzle switches off. you spill fuel onto your bare skin you inhale fuel vapors 184 Replace fuel filler cap 2 and turn it clockwise.
Operation Engine Engine Hood Warning G Do not pull the release lever while the vehicle is in motion. The hood could otherwise open, thereby impairing visibility and leading to loss of control of the vehicle. For this reason, only open the hood when the vehicle is parked. Opening !CAUTION Make sure that the windshield wipers are not folded away from the windshield. The windshield wipers or the hood may otherwise be damaged. N88.40-2060-31 N88.
Operation Engine Warning G If the hood support strut is not engaged, the hood can fall shut. You could be injured. After opening the hood, you should therefore check whether the support strut is engaged. Warning G The engine has an electronic ignition system which carries a high voltage. For this reason, you must never touch the ignition system components (ignition coil, test socket) while: the engine is running 4 Swing the hood upward until support strut 3 engages and the hood is supported.
Operation Engine If the hood can be raised slightly, it is not properly engaged. Open it again and allow it to drop from a slightly greater height. !CAUTION Do not use your hands to push the hood down. Doing so could damage it. Warning G If handled incorrectly, service products can constitute a health risk for people and an environmental hazard. Always observe relevant guidelines for handling, storing and disposing of service products.
Operation Engine Checking the engine oil level in the display In vehicles with diesel engines, you can view the engine oil level in the display. When the oil is being checked, the vehicle must be standing level be at normal operating temperature 4 have been standing with the engine switched off for at least five minutes i If no oil level reading is shown again, check the engine oil level with the dipstick.
Operation Engine The following message is displayed for the duration of the measurement process: N Engine oil level Measuring in N Observe Carry out another wait. period measurement after approximately 5 minutes when the engine is at normal operating temperature. progress The following messages may be displayed: N Engine oil level OK Do not add oil. Engine oil Add 1.0 quart Add the amount of oil shown ( page 190). Engine oil Add 1.
Operation Engine i The difference in the quantity of oil between the upper and lower marks on the dipstick is approx. 2 US qts (2 l) in vehicles with diesel engines 3 US qts (3 l) in vehicles with gasoline engines 4 1 Engine oil filler neck 2 Engine oil dipstick Wipe it clean with a lint-free cloth. N18.00-2041-31 Insert it into the dipstick tube as far as the stop and pull it back out. 3 Engine oil dipstick Check the engine oil level.
Operation Engine Environmental note H Warning When adding oil, take care not to spill any. No engine oil must be allowed to enter sewage systems, surface water, ground water or soil. You would otherwise be damaging the environment. Dispose of engine oil in an environmentally responsible manner. Comply with the manufacturer’s instructions. Coolant The expansion tank is in the engine compartment. Only add coolant with the vehicle standing on a level surface and with the engine switched off.
Operation Engine !CAUTION Check the cooling and heating systems regularly for leaks. If a large quantity of coolant is lost, have the cause traced and rectified at an authorized Sprinter Dealer. N20.30-2063-31 Brake fluid 4 The reservoir is in the engine compartment. Check the brake fluid level: regularly, e.g.
Operation Engine You should always wear eye protection and gloves when you are adding brake fluid. Only store brake fluid in its closed original container and keep out of the reach of children. Comply with safety regulations when handling brake fluid. Warning G If the boiling point of the brake fluid is too low, vapor pockets may form in the brake system when the brakes are applied hard (e.g. when driving on long downhill stretches).
Operation Engine Vehicle assemblies Check assemblies regularly for leaks. In the event of fluid loss (e.g. spots of oil under the vehicle when it has been parked), have the cause traced and rectified immediately at an authorized Sprinter Dealer which has the necessary specialist knowledge and tools to carry out the work required. 4 The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose.
Operation Battery Battery Your vehicle may be equipped with two batteries, depending on the equipment version: B Starter battery in the battery recess in the driver’s footwell Auxiliary battery in the engine compartment* Warning A D G C Risk of explosion When batteries are being charged, explosive detonating gas is emitted. Only charge batteries in wellventilated areas. E Risk of explosion Because of the risk of explosion, avoid creating sparks from fire, open flames and smoking.
Operation Battery The batteries must always be sufficiently charged so that they achieve their intended service life. Have the battery charge status checked more frequently if you use the vehicle mainly for short trips or if you leave it parked up for a long period. 4 If you intend to leave your vehicle parked up for a long period, seek advice from an authorized Sprinter Dealer and switch off the electrical system at the battery isolating switch ( page 197).
Operation Battery isolating switch* You can disconnect the current to all your vehicle’s consumers using the battery isolating switch. This will prevent uncontrolled battery discharge caused by quiescent current consumption. Warning The battery isolating switch is to the right of the accelerator pedal in the driver’s footwell.
Operation Battery isolating switch* Switching on the electrical system Insert the key into the ignition lock. Press connector 1 onto ground pin 2 until you feel it engage and the lock inhibitor is released. The connector must be in full contact with ground pin 2. Move the red slide up until it engages. All consumers are reconnected to the power supply circuit.
Operation Tires and wheels Tires and wheels The tires on a new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The vehicle manufacturer strongly recommends using tires equivalent to the originals in size, quality and performance when a replacement becomes necessary. Refer to the tire and loading information placard on the driver’s door B-pillar ( page 373) for the size designation of your tire.
Operation Tires and wheels Warning 4 G Do not use a tire, wheel size or rating other than that specified for your Sprinter vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your Sprinter vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
Operation Tires and wheels Radial-ply tires Warning Other tire valves could be damaged by the specified tire pressures. Tire valves (snap-in valves) G Warning G Important guidelines Combining radial ply tires with other types of tires on your Sprinter vehicle will change the vehicle’s handling characteristics and may lead to an accident resulting in death, severe personal injuries and property damage. Always use radial ply tires in sets of 4 (or 6, in case of vehicles with dual rear wheels).
Operation Tires and wheels When replacing individual tires, you should mount new tires on the front wheels first. Tire care and maintenance Warning 4 G Regularly check the tires for damage. Damaged tires can cause tire inflation pressure loss. As a result, you could lose control of your vehicle. Worn, old tires can cause accidents. If the tire tread is badly worn, or if the tires have sustained damage, replace them. The tire inflation pressure should be checked regularly, i.e.
Operation Tires and wheels You could lose control of the vehicle as a result, cause an accident and injure yourself or others. Avoid driving up against curbs or parking the vehicle with part of the tire tread surface on the curb. Life of tire The service life of a tire depends on varying factors including but not limited to: Driving style Tire inflation pressure Do not allow your tires to wear down too far.
Operation Tires and wheels Cleaning tires !CAUTION Never use a round nozzle to power wash tires. The intense jet of water can result in damage to the tire. Always replace a damaged tire. Direction of rotation 4 1 Treadwear Indicator (TWI) The Treadwear Indicator appears as a solid band across the tread. Storing tires !CAUTION Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline/diesel.
Operation Tires and wheels Loading the vehicle The following labels on the vehicle show how much weight it may properly carry. Only vehicles with a gross weight capacity less than 10,000 lbs (4500 kg) also tells you about the front and rear axle weight capacity, called the Gross Axle Weight Rating (GAWR). The GAWR is the total allowable weight that can be carried by a single axle (front or rear). Never exceed the GVWR or GAWR for either the front axle or rear axle.
Operation Tires and wheels Placard i Load limit information For vehicles with a gross weight capacity less than 10,000 lbs (4500 kg) only. The data shown on this placard is for illustrative purposes only. The load limit data and seating data are specific to each vehicle and may vary from the data shown in the illustration below. Refer to the placard on your vehicle for actual data specific to your vehicle.
Operation Tires and wheels Step 1 Step 4 Step 6 (if applicable) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be five 150 lbs passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400750 (5 x150) = 650 lbs).
Operation Tires and wheels Example Combined weight limit of occupants and cargo from placard 1 1500 lbs Number of Seating occupants configura(driver and tion passengers) Occupants' weight Combined Available cargo/luggage and trailer weight of all tongue weight (total load limit or occupants vehicle capacity weight from placard minus combined weight of all occupants) 5 Occupant 1: 150 lbs Occupant 2: 180 lbs Occupant 3: 160 lbs Occupant 4: 140 lbs Occupant 5: 120 lbs 750 lbs 1500 lbs - 750 lbs = 750
Operation Tires and wheels Certification label Even after careful determination of the combined weight of all occupants, cargo and the trailer tongue load (if applicable) as to not exceed the permissible load limit, you must make sure that your vehicle never exceeds the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for either the front or rear axle and the Gross Combination Weights Rating (GCWR) (if applicable).
Operation Tires and wheels To assure that your vehicle does not exceed the maximum permissible weight limits (GVWR and GAWR for front and rear axle), have the loaded vehicle (including driver, passengers and all cargo and, if applicable, trailer fully loaded) weighed on a suitable commercial scale. Trailer tongue load The tongue load (tongue weight at the 4 hitch ball) of any trailer is an important weight to measure because it affects the load you can carry in your vehicle.
Operation Tires and wheels Do not make a visual judgment when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. For more information, refer to “Important notes on tire inflation pressure”. The tire inflation pressure should be checked regularly, i.e. at least each time you refuel the vehicle, and should only be adjusted on cold tires. The preferred interval for checking the tire inflation pressure, however, is before each trip.
Operation Tires and wheels The placard lists the recommended cold tire inflation pressures for all load conditions up to the maximum permissible weight limits (GAWR). The tire inflation pressures listed apply to the tires installed as original equipment. Important notes on tire inflation pressure 4 Warning G If the tire inflation pressure repeatedly drops: Check the tires for punctures from foreign objects. Check to see whether air is leaking from the valves or from around the rim.
Operation Tires and wheels Checking tire inflation pressure The tire inflation pressure should be checked regularly, i.e. at least each time you refuel the vehicle. The preferred interval for checking the tire inflation pressure, however, is before each trip.
Operation Tires and wheels !CAUTION i i After inspecting or adjusting the tire inflation pressure, always reattach the valve cap if equipped. USA only: Canada only: The Tire Pressure Monitoring System (TPMS) is equipped with a combination low tire pressure/TPMS malfunction telltale in the instrument cluster ( page 14).
Operation Tires and wheels pressure which was stored at the time of calibration of the TPMS after you inflated the tires. Always ensure that you re-calibrate the TPMS after you inflated the tires to the recommended cold inflation pressure. Always adjust tire inflation pressure according to the tire and loading information placard on the driver’s door B-pillar. Underinflated tires wear excessively and/or unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.
Operation Tires and wheels 4 TPMS malfunctions may occur for a variety of reasons, including the installation of incompatible replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
Operation Tires and wheels Press the , menu button on the instrument cluster. The following message is displayed: OK TPMS The tire pressure monitor activation process has begun. The tire pressures of the individual wheels are stored as the new reference values if they are determined to be plausible for the tire pressure monitor. If you wish to cancel the activation process: Press the . button or the 5 menu button on the instrument cluster.
Operation Tires and wheels i i i Possible differences between the readings of a tire pressure gauge of an air hose, e.g. gas station equipment, and the vehicle’s control system can occur. Usually the readings issued by the control system are more precise. When the message Tire pres. dis- If a spare wheel without wheel sensors is mounted, the system may still indicate the tire inflation pressure of the removed wheel for some minutes.
Operation Tires and wheels Always adjust the tire inflation pressure according to the tire and loading information placard on the driver’s door B-pillar. Underinflated tires wear excessively and/or unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.
Operation Tires and wheels 4 TPMS malfunctions may occur for a variety of reasons, including the installation of incompatible replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
Operation Tires and wheels Press the j or k button repeatedly until you see the current inflation pressures for each tire appear in the display or the following message appears in the display Tire pres. displayed after driving for several minutes Press reset button 0 on the instrument cluster ( page 14). The following message will appear in the multifunction display: Tire pres. Adjust pres. Press æ button. The following message will appear in the multifunction display: Tire pres.
Operation Tires and wheels Tire size designation, load and speed rating 3. Ride comfort and vehicle stability Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride. Tire labeling Besides the tire name (sales designation) and manufacturer's name, a number of markings can be found on a tire. 4 Below are some explanations regarding the markings on your vehicle’s tires: i For illustrative purposes only.
Operation Tires and wheels Tire sizes for Sprinter vehicles Sprinter type 2500 LT 245/75 R 16 120/116 L LT 245/75 R 16 120/116 N 3500 LT 215/85 R 16 115/112 N LT 215/85 R 16 115/112 Q Design standard Depending on the design standards used, the tire size molded into the side wall may have no letter or a letter 1 preceding the tire width or the tire load rating designation. Letter “LT” preceding the size designation: Light Truck tire based on U.S. design standards.
Operation Tires and wheels Warning G The tire load rating must always be at least half of the GAWR of your vehicle. Otherwise, tire failure may be the result which may cause an accident and/or serious personal injury to you or others. 4 Always replace rims and tires with the same designation, manufacturer and type as shown on the original part. Warning G Do not overload the tires by exceeding the specified load limit as indicated on the placard located on the driver’s door B-pillar.
Operation Tires and wheels Index Speed rating F up to 50 mph (80 km/h) G up to 56 mph (90 km/h) J up to 62 mph (100 km/h) K up to 68 mph (110 km/h) L up to 74 mph (120 km/h) M up to 80 mph (130 km/h) N up to 87 mph (140 km/h) P up to 93 mph (150 km/h) Q up to 100 mph (160 km/h) R up to 106 mph (170 km/h) The TIN is a unique identifier which facilitates efforts by tire manufactures to notify purchasers in recall situations or other safety matters concerning tires and gives purchasers th
Operation Tires and wheels DOT (Department Of Transportation) A tire branding symbol 1 which denotes the tire meets requirements of the U.S. Department of Transportation. Manufacturer’s identification mark The manufacturer’s identification mark 2 denotes the tire manufacturer. New tires have a mark with two symbols. 4 Retreaded tires have a mark with four symbols. For more information on retreaded tires, see ( page 199).
Operation Tires and wheels Warning G Maximum tire inflation pressure Do not overload the tires by exceeding the specified load limit as indicated on the tire and loading information placard on the driver’s door B-pillar. Overloading the tires can overheat them, possibly causing a blowout. Overloading the tires can also result in handling or steering problems, or brake failure.
Operation Tires and wheels Tire ply material Tire and loading terminology Accessory weight The combined weight (in excess of those standard items which may be replaced) of automatic transmission, power steering, power brakes, power windows, power seats, radio, and heater, to the extent that these items are available as factory-installed equipment (whether installed or not). 4 1 Plies in side wall 2 Plies under tread i For illustrative purposes only.
Operation Tires and wheels DOT (Department Of Transportation) GVW (Gross Vehicle Weight) Maximum load rating A tire branding symbol which denotes that the tire meets the requirements of the U.S. Department of Transportation. The GVW comprises the weight of the vehicle including fuel, tools, spare wheel, installed accessories, passengers and cargo and, if applicable, trailer tongue load. The GVW must never exceed the GVWR indicated on the certification label located on the driver’s door B-pillar.
Operation Tires and wheels Production options weight Rim Tire ply composition and material used The combined weight of those installed regular production options weighing over 5 lbs (2.3 kilograms) in excess of those standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim. A metal support for a tire or a tire and tube assembly upon which the tire beads are seated.
Operation Tires and wheels TWR (Tongue Weight Rating) Rotating tires Maximum permissible weight on the trailer tongue. Warning Uniform tire quality grading standards A tire information system that provides consumers with ratings for a tire’s traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the side wall of the tire.
Operation Tires and wheels The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. !CAUTION If your vehicle is equipped with the tire pressure monitor*, each wheel has an electronic component. 4 Tire mounting tools should not be applied in the area of the valve, as this could damage the electronic components. Have the tires changed only at an authorized Sprinter Dealer. Thoroughly clean the mounting face of wheels and brake disks, i.e.
Operation Tires and wheels Dual rear wheels: Rotate front tires by axle and the outer rear tire side to side if there is no approved direction of rotation. The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. !CAUTION 3500 dual rear tires have only one approved direction of rotation.
Operation Winter driving Winter driving Have your vehicle winterproofed at the onset of winter at an authorized Sprinter Dealer.
Operation Winter driving Warning G If you use your spare tire when winter tires are fitted on the other wheels, be aware that the difference in tire characteristics may impair turning stability and overall driving stability may be reduced. Adapt your driving style accordingly. Have the spare tire replaced with a winter tire at the nearest authorized Sprinter Dealer. i When they have been removed, store wheels and tires in a cool, dry, and if possible dark place.
Operation Winter driving Snow chains Use "Class U" chains, or other traction aids that meet SAE Type "U" specifications. 4 Snow chains must be the proper size for the vehicle, as recommended by the chain manufacturer. They should only be driven on snow-covered roads at speeds not to exceed 30 mph (50 km/h). Remove chains as soon as possible when driving on roads without snow. !CAUTION Use snow chains on rear wheels only. Some tire sizes do not leave adequate clearance for snow chains.
Operation Maintenance and servicing Maintenance and servicing Warning G Before carrying out maintenance operations and repairs, please make sure that you read the relevant sections of the technical documentation, such as: Operating instructions and workshop information Familiarize yourself in advance in particular with legal requirements, such as: Safety at work and accident prevention regulations. You may otherwise fail to recognize dangers and could injure yourself or others.
Operation Maintenance and servicing Warning G If handled incorrectly, service products can constitute a health risk for people and an environmental hazard. Always observe relevant guidelines for handling, storing and disposing of service products. Active Service System (ASSYST)* ASSYST, the Active Service System, informs you when the next service is due. A service that is due is displayed about a month or 1900 miles (3000 km) in advance.
Operation Maintenance and servicing Vehicles without steering wheel buttons Vehicles with steering wheel buttons* Calling up the service due date The following messages may be displayed: If you have missed the service due date, one of the following messages appears in the display: Switch on the ignition ( page 67). 9 Service A overdue by .. days Vehicles with steering wheel buttons* 9 Service A overdue by ..
Operation Maintenance and servicing Vehicles without steering wheel buttons Press the menu button on the instrument cluster repeatedly until you see the following in the display: 9 for service A Air cleaner for the air-conditioning system in the rear compartment* An increased amount of sand or dust may collect in the air cleaner when you drive on dusty or sandy roads. ´ for service B Carefully pry cover 1 out of recesses 2 and remove it.
Operation Cleaning and care of the vehicle Cleaning and care of the vehicle Regular and proper care will help to maintain the value of your vehicle. The best way to protect your vehicle from harmful environmental influences is to wash it and use protective treatments regularly. i It is recommended that you use Mopar care products. These have been specially adapted to Sprinter vehicles and are state of the art. Mopar care products are available from any authorized Sprinter Dealer.
Operation Cleaning and care of the vehicle Care of the vehicle !CAUTION 4 After cleaning your vehicle, especially the wheel rims with rim cleaner, do not simply park the vehicle and leave it. Rim cleaners can promote corrosion of the brake discs and the brake pads/ linings. Before parking and leaving the vehicle after cleaning, always warm the vehicle up to normal operating temperature first. Automatic car wash You can clean the vehicle in an automatic car wash from the very start.
Operation Cleaning and care of the vehicle Steps Warning Light-alloy wheels* G Dirty or iced-up steps and entrances create a risk of slipping or falling. Keep steps, entrances and footwear free from dirt (e.g. mud, clay, snow and ice). Engine cleaning !CAUTION Do not allow water to enter the intake and ventilation openings. When cleaning with high-pressure water or steam cleaners, the spray must not be aimed directly at electrical components or at the end of electrical lines.
Operation Cleaning and care of the vehicle Windows !CAUTION 4 Do not use a dry cloth, abrasive material, solvent or solvent-based cleaning agent to clean the inside of the windows. Clean the inside of the windows with a damp cloth or a commercially available glass cleaner. Do not touch the inside of the rear and side windows with hard objects, such as an ice scraper or a ring. You could otherwise damage the windows or the rear window heating.
Operation Cleaning and care of the vehicle Clean the camera lens 1 using water and a soft cloth only. Be careful not to apply wax to the camera lens 1 when waxing the vehicle. If necessary, remove the wax using shampoo with plenty of water. !Do not use dry, coarse or hard cloths and aggressive cleaning agents. Do not scrub or use high pressure. You will otherwise scratch or damage the lens or the camera.
Operation Cleaning and care of the vehicle Seat belts Remove stains or dirt immediately to prevent damage or the build-up of residues. 4 After driving off-road or on construction sites G !CAUTION Warning Clean the seat belts with a mild washing solution. Do not dry the seat belts in direct sunlight or at temperatures above 176 °F (80 °C). Dirt on the vehicle can affect road and operating safety. Do not bleach or dye the seat belts. This could impair the function of the seat belts.
Operation Cleaning and care of the vehicle Clean the vehicle, particularly the lighting equipment, windows, exterior mirrors, steps, entrances, grab handles, wheels, tires, wheel housings and license plates. Observe the notes in this section. Remove any trapped foreign objects, e.g. stones. Warning G Dirty brake discs and brake pads/linings can impair braking power (to the point of total failure). You could thereby cause an accident.
Practical hints What to do if ... ......... 250 Display messages ......... 281 Where will I find...? ......... 299 Changing bulbs ......... 306 Changing the batteries ......... 315 Fuel system ......... 317 Replacing the wiper blades ......... 319 Flat tire ......... 320 Battery ......... 335 Jump-starting ......... 340 Towing ......... 342 Fuses .........
Practical hints What to do if ... Audible warning signals Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at an authorized Sprinter Dealer.
Practical hints What to do if ... Accident Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. Problem Possible cause/result Fuel is leaking from the vehicle.
Practical hints What to do if ... Fuel and fuel tank Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has Problem the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. Possible cause/result Suggested solutions Bleed the fuel system ( page 318). The fuel tank has been run dry and the vehi- There is air in the fuel system. cle has a diesel engine.
Practical hints What to do if ... Engine Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at an authorized Sprinter Dealer. There is a risk of an accident and injury if this work is carried out incorrectly.
Practical hints What to do if ... Problem Possible cause/result Suggested solutions The engine does not start. The on-board voltage is too low (the battery The engine may be jump-started You cannot hear the starter motor working. has too little charge or is discharged). ( page 340). The selector lever is not in position P or N. If the engine does not start despite jumpstarting: Consult an authorized Sprinter Dealer. The battery isolating switch is disconnected.
Practical hints What to do if ... Problem Possible cause/result Suggested solutions The coolant temperature gauge is above 250 °F (+120 °C). The coolant is too hot and the engine is not Park your vehicle in a safe location as being sufficiently cooled. quickly as possible and let the engine continue to run at idle speed for about 1 to 2 minutes before switching it off. This allows the coolant temperature to return to normal again.
Practical hints What to do if ... Automatic transmission Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has 5 the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at an authorized Sprinter Dealer.
Practical hints What to do if ... Headlamps and turn signals Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has Problem the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. Possible cause/result The headlamps are fogged up on the inside. Air humidity is very high.
Practical hints What to do if ... Windshield wipers Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at an authorized Sprinter Dealer.
Practical hints What to do if ... Remote control Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at an authorized Sprinter Dealer.
Practical hints What to do if ... Problem Possible cause/result Suggested solutions It is no longer possible to lock or unlock the The remote control batteries are weak or dis- Point the remote control towards the vehicle using the remote control. charged. driver’s door handle at close range and try again. If this does not work: Lock or unlock the vehicle using the key ( page 54). Check the batteries of the remote control ( page 53). Change the batteries if necessary ( page 315).
Practical hints What to do if ... Problem Possible cause/result The key can no longer be turned in the igni- The on-board voltage is too low. tion lock. Suggested solutions Remove the key and re-insert it into the ignition lock. Switch off all non-essential consumers, for example the seat heating, interior lighting, and try to turn the key again. If this does not work: Check the starter battery and charge it if necessary. or The engine may be jump-started ( page 340).
Practical hints What to do if ... Driving systems Warning G Always have maintenance work carried out at an authorized Sprinter Dealer which has 5 the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at an authorized Sprinter Dealer.
Practical hints What to do if ... Problem Possible cause/result Suggested solutions The speed cannot be set with cruise control* activated1. The display is showing a message of high pri- Proceed as instructed by the mesority and cannot therefore show a change in sage in the display. speed. Deactivate cruise control* if necessary. 1 Only on vehicles with steering wheel buttons.
Practical hints What to do if ... Auxiliary heating* Warning tools to carry out the work required. G Always have maintenance work carried out at an authorized Sprinter Dealer which has the necessary specialist knowledge and Problem 5 The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be Possible cause/result carried out at an authorized Sprinter Dealer.
Practical hints What to do if ... Problem Possible cause/result Suggested solutions The auxiliary heating does not switch on or WARNING the auxiliary heating checked at G Have the engine does not start an authorized Sprinter Dealer. The auxiliary heating has overheated about ten times in succession. The engine or heater is malfunctioning. The heater has overheated. The coolant level is too low.
Practical hints What to do if ... Indicator and warning lamps in switches Warning the necessary specialist knowledge and tools to carry out the work required. G Always have maintenance work carried out at an authorized Sprinter Dealer which has Problem 5 The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. Possible cause/result In particular, work relevant to safety or on safety-related systems must be carried out at an authorized Sprinter Dealer.
Practical hints What to do if ... Problem Possible cause/result The residual engine heat utilization funcThere is insufficient voltage available as too tion switches off too soon or cannot be many consumers are switched on. switched on. The indicator lamp in the ° switch does not light up. Suggested solutions Switch off all non-essential consumers, for example the reading lamps, interior lighting, etc.
Practical hints What to do if ... Indicator and warning lamps in the instrument cluster G Warning Always have maintenance work carried out at an authorized Sprinter Dealer which has Problem v 5 the necessary specialist knowledge and tools to carry out the work required. The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose.
Practical hints What to do if ... Problem # k 6 6 Possible cause/result Suggested solutions The yellow ESP , ABS, ASR/BAS WARNING observe the messages in the disG Also indicator lamps and the red play on vehicles with steering wheel brake system indicator lamp are EBV has been deactivated due to undervoltbuttons ( page 284). lit while the engine is running. age. Stop your vehicle as soon as it is safe to do so. The battery may not be being charged.
Practical hints What to do if ... Problem k Possible cause/result Suggested solutions driving, but with even greatThe yellow ASR/BAS indicator WARNING G Continue er care. lamp is lit while the engine is runASR has been deactivated due to a malfunc- Have the system checked at an authoning. tion. rized Sprinter Dealer as soon as possible. The engine power output may then be lower. WARNING G Continue driving, but with even greater care.
Practical hints What to do if ... Problem - Possible cause/result The yellow ABS indicator lamp is lit while the engine is running. Suggested solutions Also observe the messages in the display on vehicles with steering wheel buttons ( page 284). ABS has been deactivated due to a malfunction. ESP®, ASR and BAS as well as cruise Continue driving, but with even greatcontrol have also been deactivated as a reer care. sult.
Practical hints What to do if ... Problem # Possible cause/result Suggested solutions observe the messages in the disThe yellow ESP® indicator lamp is WARNING G Also play on vehicles with steering wheel lit while the engine is running. buttons ( page 284). ESP® has been deactivated due to a malfunction. Cruise control is also switched off Continue driving, but with even greatas a result. er care.
Practical hints What to do if ... Problem # Possible cause/result Suggested solutions The red battery charge warning immediately and check the polyWARNING G Stop V-belt. lamp lights up while the engine is The battery is not being charged. Possible running. If it is torn: causes: Do not drive any further. Consult malfunctioning alternator the nearest authorized Sprinter Dealer. torn poly-V-belt If it is not damaged: Have your vehicle checked at an authorized Sprinter Dealer.
Practical hints What to do if ... Problem Possible cause/result Suggested solutions The engine oil level has dropped to the min- Check the engine oil level and add enimum level. If the engine oil level falls any gine oil at the nearest refueling stafurther, the indicator lamp will light up contion ( page 190). tinuously. If there is visible oil loss from the engine, have the fault rectified immediately at an authorized Sprinter Dealer.
Practical hints What to do if ... Problem Possible cause/result Suggested solutions : The yellow engine oil level warning The engine oil level has exceeded the maxi- Check the engine oil level and have any excess oil siphoned off at the lamp lights up, the HI engine oil mum level. nearest refueling station level message appears in the dis( page 190). play and the warning buzzer The engine or the catalytic converter sounds after the engine is started could be damaged.
Practical hints What to do if ... Problem • The red coolant warning lamp lights up while the engine is running. Possible cause/result Suggested solutions The coolant temperature is too high. Do not drive any further. Consult an authorized Sprinter Dealer. If the vehicle is switched off after being subjected to extreme loads (for example driving in mountainous terrain, trailer towing, etc.), the coolant warning lamp may light up when the ignition is switched on or the engine is restarted.
Practical hints What to do if ... Problem ± Possible cause/result The yellow engine diagnostic in- The fuel tank has run dry. dicator lamp lights up or flashes The engine may be running in emergency while the engine is running. mode. Suggested solutions Refuel at the nearest refueling station. On vehicles with a diesel engine: Bleed the fuel system ( page 318). Start the engine three to four times after refueling. Emergency mode will be canceled. You do not need to have your vehicle checked.
Practical hints What to do if ... Problem X Possible cause/result USA only: WARNING Suggested solutions G Combination low tire pressure/ The TPMS detects a loss of pressure in at TPMS malfunction telltale for least one tire. TPMS lights up continuously. Canada only: Low tire pressure telltale for TPMS lights up continuously. 5 X USA only: Combination low tire pressure/ TPMS malfunction telltale for TPMS flashes 60 seconds and then stays illuminated.
Practical hints What to do if ... Warning! G Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or the tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or the tire inflation pressure label, you should determine the proper tire inflation pressure for those tires).
Practical hints What to do if ... Problem 5 Possible cause/result Suggested solutions / The yellow water separator indi- The water that has collected in the water sep- Drain the water separator cator lamp1 lights up while the arator has reached the maximum level. ( page 317). ignition is on. Have the water separator drained at an authorized Sprinter Dealer. W The yellow washer fluid level in- The windshield washer fluid level is too low.
Practical hints Display messages i All warning/indicator lamps (except the turn signal indicator lamps) and the display are activated when the ignition is switched on. Please check that they are working properly before commencing a journey. Display messages on vehicles without steering wheel buttons Warnings, malfunctions or additional information may also be shown in the display. The following table shows messages which could appear in the display.
Practical hints Display messages Display messages Possible cause/result Possible solution N There is insufficient or no oil in the engine. There is a risk of engine damage. Stop your vehicle as soon as it is safe to do so. Switch off the engine. Check the engine oil level using the dipstick ( page 189). If the oil level is correct, have the malfunction rectified immediately at an authorized Sprinter Dealer.
Practical hints Display messages Display messages Possible cause/result Possible solution — — The tire pressure monitor detects a moderate loss of pressure in at least one of the tires, or the difference in pressure on one axle is too great. Check the tire pressure at the earliest opportunity and correct it if necessary. The message is displayed for 30 seconds. TPMS The message is also displayed after 30 seconds.
Practical hints Display messages Display messages on vehicles with steering wheel buttons The operating system shows warnings, malfunctions or additional information in the display. If you select the Malfunction memory menu in the operating system ( page 95), the acknowledged and unacknowledged messages will appear. Warning G Certain messages are accompanied by a warning signal or a permanent tone.
Practical hints Display messages Text messages Display messages ABS Visit workshop Possible cause/result WARNING Possible solution G Continue driving, but with even greater care. ABS has been deactivated due to a malfunc- Have the system checked at an authotion. ESP®, ASR and BAS as well as cruise rized Sprinter Dealer as soon as possicontrol have also been deactivated as a reble. sult. The brake system is still available with the full brake boosting effect but without ABS.
Practical hints Display messages Display messages ESP Visit workshop Possible cause/result WARNING Possible solution G ESP® has been deactivated due to a malfunction. Cruise control is also switched off as a result. Vehicle stability is no longer automatically controlled in good time. Continue driving, but with even greater care. Have the system checked at an authorized Sprinter Dealer as soon as possible. Engine power output may be reduced.
Practical hints Display messages Display messages Possible cause/result Possible solution Tire pres. monitor currently unavailable The TPMS or Advanced TPMS* is unable to monitor the tire pressure due to As soon as the causes of the malfunction have been removed, the TPMS automatically becomes active again after a few minutes of driving. Tire pres.
Practical hints Display messages Display messages SRS Restraint system Visit workshop Possible cause/result WARNING Possible solution G The restraint systems have malfunctioned. The airbags or emergency tensioning retractors could be triggered unintentionally, or not at all in the event of an accident. 5 288 Continue driving, but with even greater care. Visit an authorized Sprinter Dealer as soon as possible.
Practical hints Display messages Symbol messages Display symbol Display message Possible cause/result Possible solution # Battery/ Alternator Visit workshop The battery is not being charged. Possible Stop immediately and check the poly-Vcauses: belt. malfunctioning alternator If it is torn: torn poly-V-belt Do not drive any further. Consult an authorized Sprinter Dealer. If it is not damaged: Drive to the nearest authorized Sprinter Dealer immediately.
Practical hints Display messages Display symbol 6 Display message Brake fluid Visit workshop Possible cause/result WARNING Possible solution G Stop your vehicle as soon as it is safe to do so. There is insufficient brake fluid in the fluid Do not add brake fluid under any circumreservoir. stances. This will not solve the problem. Do not drive any further. Consult an authorized Sprinter Dealer. .
Practical hints Display messages Display symbol Display message Possible cause/result k Visit workshop WARNING Possible solution G ASR has been deactivated due to a malfunction. Cruise control is also switched off as a result. The engine power output may then be lower. WARNING G BAS has been deactivated due to a malfunction. The brake system continues to function with the normal braking effect but with no electronic support. k unavailable Please enter PIN: < Seatbelt sys.
Practical hints Display messages Display symbol Display message Possible cause/result Possible solution Z Coolant Stop, turn engine off The coolant temperature is too high. Do not drive any further. Consult an authorized Sprinter Dealer. If the vehicle is switched off after being subjected to extreme loads (for example driving in mountainous terrain, trailer towing, etc.), this message may be displayed when the ignition is switched on or the engine is restarted.
Practical hints Display messages Display symbol Display message Possible cause/result Possible solution . Brake lamp right The right-hand brake lamp is malfunctioning. Change the bulb as soon as possible. Third brake lamp The third brake lamp is malfunctioning. This message will only appear if all LEDs have failed. Visit an authorized Sprinter Dealer as soon as possible. High beam left The left-hand high-beam headlamp is malfunctioning. Change the bulb as soon as possible.
Practical hints Display messages Display symbol Display message Possible cause/result Possible solution . Additional ind. lamps An additional turn signal is malfunctioning. Visit an authorized Sprinter Dealer as soon as possible. Cornering lamp left The left-hand cornering lamp* is malfunc- Visit an authorized Sprinter Dealer as tioning. soon as possible. Cornering lamp right The right-hand cornering lamp* is mal- functioning. 5 Visit an authorized Sprinter Dealer as soon as possible.
Practical hints Display messages Display symbol Display message Possible cause/result Possible solution C Warning Tire defect One or more tires are deflating. Carefully bring the vehicle to a halt, avoiding abrupt steering and braking maneuvers. Check tire(s) The respective tire is shown in the multifunction display. The tire pressure in one or more tires is already below the minimum value. The respective tire is shown in the multifunction display. If necessary, change the wheel.
Practical hints Display messages Display symbol Display message Possible cause/result Possible solution N Engine oil level Stop, turn engine off There is insufficient or no oil in the engine. There is a risk of engine damage. Stop your vehicle as soon as it is safe to do so. Switch off the engine. Check the engine oil level using the dipstick ( page 189). If the oil level is correct, have the malfunction rectified immediately at an authorized Sprinter Dealer.
Practical hints Display messages Display symbol Display message Possible cause/result Possible solution N Engine oil level Reduce oil level You have added too much engine oil. There is a risk of damage to the engine or the catalytic converter. Check the engine oil level and have any excess oil siphoned off at the nearest refueling station ( page 190). The engine or the catalytic converter could be damaged.
Practical hints Display messages Display symbol Display message Possible cause/result 9 Doors open You are already driving at walking pace, Close the doors. even though not all the doors are closed. Hood open You are already driving at walking pace, even though the hood is not closed. / Water in Fuel Visit workshop The water that has collected in the water Drain the water separator ( page 317). separator has reached the maximum lev- or el.
Practical hints Where will I find...? Warning triangle and warning lamp The warning triangles are behind the driver's seat. Fire extinguisher The fire extinguisher is secured to the front of the co-driver’s seat base. First-aid kit The first-aid kit is located in the storage compartment in the co-driver’s door. N72.10-2148-31 5 1 Warning triangles Remove warning triangles 1 from the brackets upward. 1 Fire extinguisher 2 Tabs 1 Locked 2 Unlocked Pull tabs 2 upward.
Practical hints Where will I find...? Jack and vehicle tool kit The jack and the vehicle tool kit are located under the hatch in the co-driver’s footwell. Warning 3 First-aid kit i 5 Check the expiry dates of the first-aid kit materials every year, and replace them if necessary. G If work is to be carried out under the vehicle, the vehicle must be placed on stands.
Practical hints Where will I find...? Spare wheel If you are replacing the tires on the vehicle, you may use the spare wheel as a road wheel provided that: Panel van/crewbus the tires are no more than 6 years old the wheel and tire have the same specified design as the road wheels The spare wheel is located in a spare wheel bracket under the rear of the vehicle. 3 Tensioning lever 4 Jack 5 Vehicle tool kit Remove the vehicle tool kit.
Practical hints Where will I find...? Chassis 3 Securing hook 4 Sleeve 5 Spare wheel bracket 5 Raise spare wheel bracket 5 slightly and release left securing hook 3. Use the pump lever to raise the spare wheel beyond the rear end of the spare wheel bracket. Carefully remove the spare wheel from the bracket. Slide the pump lever for the jack into sleeve 4 on spare wheel bracket 5. Warning Raise spare wheel bracket 5 using the pump lever and release right securing hook 3.
Practical hints Where will I find...? Raise spare wheel bracket 4 using the pump lever and release right securing hook 1. Slowly lower spare wheel bracket 4 to the ground. Premium tire sealant* The Premium tire sealant is located in the storage compartment in the right-hand doorway. Raise spare wheel bracket 4 slightly and pull the pump lever out of sleeve. Chock Panel Van The wheel chock (optional for model vehicle type 2500) is on the right-hand side of the load compartment.
Practical hints Where will I find...? Chassis The wheel chock is on the left-hand side behind the rear axle. Sliding sunroof* If it is no longer possible to close the sliding sunroof, you can close it manually by operating the drive located behind the trim at the front of the sliding sunroof. N77.20-2041-31 3 Opening 4 Emergency operation key Take emergency operation key 4 from the vehicle document wallet in the glove box.
Practical hints Where will I find...? With the ignition switched on ( page 67), press and hold the sliding sunroof switch ( page 145) forward or backward for 45 seconds to reset the electronics. Reset the sliding sunroof ( page 146). Releasing the parking lock manually In the event of a malfunction, it is possible to manually release the selector lever from the lock in parking position P, for example to have the vehicle towed away. N27.
Practical hints Changing bulbs Changing bulbs Bulbs and lights are an important aspect of vehicle safety. For this reason, make sure that all bulbs are in working order at all times. Before changing bulbs Switch off the lights to avoid a short circuit. Only touch new bulbs with a clean lintfree cloth or something similar. Do not work with wet or greasy fingers. 5 Only fit 12 V bulbs of the same type as before and of the correct wattage. Have the headlamp setting checked regularly.
Practical hints Changing bulbs Front bulbs Bulb 6 Parking lamp/side marker/standing lamp (Canada only) Model WY 5 W Switch off the lighting. Open the hood ( page 185).
Practical hints Changing bulbs Press catches 1 down. Swing housing cover 2 in the direction of the arrow and remove it. Swing housing cover 2 toward headlamp casing. Place bulb holder 1 into the lamp and turn it clockwise. Pull first the inner and then the outer catch 1 upward until it audibly engages in place. Parking lamps/side marker Turn signals 5 3 Low-beam headlamps 4 Halogen high-beam headlamps/xenon headlamp cornering lamp* Pull the connector off the bulb holder.
Practical hints Changing bulbs Rear bulbs Bulb Model 1 Third brake lamp LED 2 Brake lamp P 21 W 3 Turn signal PY 21 W 4 Tail lamp/ R5W side marker/Standing lamp (Canada only) 5 License plate lamp W5W 6 Rear foglamp (driver’s P 21 W side) N82.
Practical hints Changing bulbs Changing the rear bulbs (van/crewbus) Press the new bulb into the bulb holder and screw it in clockwise. Switch off the lighting. Plug the connectors into the bulb holder. Rear lamp units Fit the rear lamp unit. To do this, clip the bulb holder into the three holes provided on the side and tighten screws 1.
Practical hints Changing bulbs 6 Tail lamp 7 Rear foglamp (driver’s side) 8 License plate lamp 9 Reverse lamp Switch off the lighting. Changing additional bulbs Switch off the lighting. Identification lamps W 5 W (cab chassis only) Undo screws 1 and remove lens 2. Turn the bulb holder 2and remove it together with the bulb. Pull the bulb out of the bulb holder 2. Press the new bulb into the bulb holder 2. Screw the bulb holder 2 containing the bulb into the lamp housing.
Practical hints Changing bulbs License plate lamp W 5 W 5 1 Bulb holder with lens 2 Recess Insert a screwdriver or similar implement into recess 2 and carefully pry off lens 1. Pull the bulb out of the bulb holder. Insert the new bulb. Align lens 1 and clip it in, making sure that it engages. Clearance lamp* W 5 W (cargo and passenger vans only) 1 Securing screw 2 Lamp housing Undo screw 1 and remove lamp housing 2 in the direction of the arrow.
Practical hints Changing bulbs Identification lamps 12V 4CP (cargo vans only) Entry lamp* W 5 W Remove bulb 2 from the bulb holder. Press the new bulb into bulb holder 2. Screw bulb holder 2 together with the bulb into lamp housing 1. N82.20-2081-31 Connect cable connector 3. The connector’s locking spring must engage. Align lamp housing 1 and engage it. 1 Securing screw Remove screw 1 and remove the lamp housing.
Practical hints Changing bulbs Interior lamp K 18 W Switch off the lighting. Press in the latching springs of lamp housing 1 using a suitable tool, for example a screwdriver. Pry off lamp housing 1. N82.20-2079-31 Remove bulb 2 from the bulb holder. Insert new bulb 2. Align lamp housing 1 on the right and engage it.
Practical hints Changing the batteries Changing the batteries If the remote control batteries (remote keyless entry) are discharged, you will only be able to lock and unlock the vehicle manually using the key. If the batteries in the auxiliary heating remote control are discharged, you will only be able to switch the auxiliary heating on or off using the auxiliary heating/heater booster switch inside the vehicle ( page 140). It is advisable to have the batteries changed at an authorized Sprinter Dealer.
Practical hints Changing the batteries Auxiliary heating remote control* You need three Micro/AAA/LR03 batteries or equivalent. N83.00-2062-31 1 Battery cover 2 Release button for mechaniocal key 5 Release the mechanical key by pressing the release button 2. Remove the battery cover 1. Remove the battery and install a new one (note correct polarity; positive terminal up). Press battery cover 1 until it snaps into place. Check the function of all remote control buttons on vehicle.
Practical hints Fuel system Fuel system Draining the fuel filter On vehicles with a diesel engine, it is necessary to drain the fuel filter if the / indicator lamp lights up. The fuel filter with water separator is in the engine compartment. Make sure that the liquid flows into the container under drain hose 1. !CAUTION Drain the fuel filter with water separator immediately if the / indicator lamp lights up. The engine could be damaged.
Practical hints Fuel system Environmental note H Have the drained liquid disposed of at an authorized Sprinter Dealer. Drain the fuel filter again if the / indicator lamp remains lit. !CAUTION 5 If the / indicator lamp remains lit even after draining for the second time, have the cause checked immediately at an authorized Sprinter Dealer.
Practical hints Replacing the wiper blades Replacing the wiper blades !CAUTION Do not open the hood while the wiper arms are folded away from the windshield. You would damage the hood and the wiper arms. Always remove the key from the ignition lock before replacing the wiper blades. Apply the handbrake ( page 115). Press two retaining clips 2 together in the direction of the arrow and fold wiper blade 1 away from wiper arm 3. Pull wiper blade 1 up and out of the retainer.
Practical hints Flat tire Flat tire The vehicle is either equipped with a spare wheel or the Premium tire sealant*. The spare wheel is located under the rear end of the vehicle if the vehicle is not equipped with Premium tire sealant* ( page 301). Warning 5 G Defective or worn tires, and tire pressures that are either too high or too low, can cause significant changes in the vehicle’s handling and braking characteristics. There is an increased risk of an accident.
Practical hints Flat tire Before raising the vehicle, also secure it against rolling away, for example using chocks or similar. Never release the handbrake while the vehicle is raised. Make sure that the distance between the underside of the tires and the ground does not exceed 1.2 in (3 cm). The vehicle could slip or topple off the jack. Do not reach under the raised vehicle with your hands or feet. Do not start the engine and avoid creating other vibrations while the vehicle is jacked up.
Practical hints Flat tire Hydraulic jack Assemble the three-part pump lever for the jack. P58.10-2053-31 Make sure that the jack is positioned vertically under the jacking points described below. Raise the vehicle by pumping the lever until the wheel is raised clear of the ground. Make sure that the distance between the underside of the tires and the ground does not exceed 1.2 in (3 cm).
Practical hints Flat tire !CAUTION Do not apply the jack to the leaf spring or the differential housing. Removing a wheel Unscrew the wheel bolts or wheel nuts. !CAUTION Do not place the wheel bolts or the wheel nuts in sand or dirt. The bolt and wheel hub threads could otherwise be damaged. For wheels with wheel nuts remove the wheel nut cover. Remove the wheel. Clean the wheel and wheel hub contact surfaces.
Practical hints Flat tire Wheels with centering by wheel bolts: For wheels with wheel nuts: Screw in the wheel bolts and tighten them finger-tight. Center the wheel nut cover over the wheel and push it onto the wheel. Tightening torque pattern Screw on the wheel nuts and tighten them finger tight. i N40.10-2175-31 Screw on the three wheel nuts that hold the wheel nut cover first.
Practical hints Flat tire For wheels with wheel bolts attach the wheel cover. Vehicles with wheel caps: Make sure that the opening in the wheel cap is positioned over the tire vent. Vehicles with center caps: Make sure that the retaining lugs of the hub cap are positioned over the bolts. i Give the middle of the center cap a knock to engage it on the wheel. Compress the piston of the hydraulic jack and close the pressure release screw. Store the jack and the remaining vehicle tools.
Practical hints Flat tire Using Premium tire sealant* You can use the Premium tire sealant to seal small punctures, particularly those in the tire tread. Tire sealants can be used at outside temperatures down to –22 °F (–30 °C). 5 G Smoking, fire and naked flames are prohibited when handling Premium tire sealant. Avoid creating sparks.
Practical hints Flat tire Warning G Comply with the manufacturer’s safety instructions as seen on the sticker on the electric air pump and the tire sealant bottle. Warning i The tire sealant is water soluble. If tire sealant escapes, you can wash it away with water. Pull connector 6 and hose 3 out of housing together with pressure gauge 5. G Tire sealant must not come into contact with your skin, eyes or clothing.
Practical hints Flat tire The following steps may vary depending on vehicle tires. Pull knob a out of valve core extractor c as far as the stop. Single tires ( page 328). Unscrew and remove the valve cap from tire valve d on the flat tire. Twin tires, inner wheel ( page 329) Twin tires, outer wheel ( page 331) Single tire Tire sealant bottle for twin tires 5 Hook the tire sealant bottle into the upper vent hole in the wheel using hook 9.
Practical hints Flat tire !CAUTION Do not connect the electric air pump connector to the cigarette lighter socket or another 12 V socket. These are not designed for operating the electric air pump. Start the engine ( page 111). Press I on electric air pump switch 1. The electric air pump is switched on. The tire sealant is then pumped into the tire and the tire pressure is increased.
Practical hints Flat tire Pull knob c out of valve core extractor a as far as the stop. This pulls the valve core into the valve core extractor and seals it against the valve core extractor stop. Hook tire sealant bottle 8 into the upper vent hole in the wheel using hook b. 5 a Valve core extractor b Hook c Knob d Angle bracket e Tire valve Pull knob c out of valve core extractor a as far as the stop. Screw valve core extractor a clockwise onto tire valve e.
Practical hints Flat tire Turn knob c clockwise until the valve core is firmly screwed into tire valve e. i Do not unscrew the valve core extractor from the tire valve while the valve core is unscrewed from the tire valve. Tire sealant could otherwise escape onto your hands. Twin tires, outer wheel The tire valve is on the inside of the outer wheel and should be horizontal on the lefthand side of the vehicle for the repair procedure. The tire sealant is water soluble.
Practical hints Flat tire Hook tire sealant valve 8 into the upper vent hole in the wheel using hook d. Allow the electric air pump to run until tire sealant bottle 8 is completely empty. Press angle bracket c on hose of tire sealant bottle 8 ( page 327) to the stop on tire valve b and clamp it into place. Press 0 on electric air pump switch 1 after about 15 seconds. Make sure that the pressure release screw on pressure gauge 5 is closed.
Practical hints Flat tire Then press 0 on electric air pump switch 1. The electric air pump is switched off. i The tire sealant is water soluble. If tire sealant escapes, you can wash it away with water. Screw the valve cap onto tire valve b. After filling with tire sealant ( page 333). Unscrew and remove angle bracket 2 from valve 7 on tire sealant bottle 8 and screw the valve cap onto the valve. Warning G Do not exceed the maximum speed of 50 mph (80 km/h). The "max.
Practical hints Flat tire Warning G If the minimum tire pressure of 43.5 psi (3.0 bar) still cannot be achieved, the tire is too badly damaged. Do not drive any further. Consult an authorized Sprinter Dealer which has the necessary specialist knowledge and tools to carry out the work required. 5 The manufacturer recommends that you use an authorized Sprinter Dealer for this purpose. In particular, work relevant to safety or on safety-related systems must be carried out at an authorized Sprinter Dealer.
Practical hints Battery Battery Your vehicle may be equipped with two batteries, depending on the equipment version: Starter battery in the battery recess in the driver’s footwell Auxiliary battery* in the engine compartment i The auxiliary battery* in the engine compartment is not suitable for jumpstarting operations. Only use the jumpstarting connection in the engine compartment if you require jump-starting assistance or wish to provide jumpstarting assistance ( page 340).
Practical hints Battery Disconnecting the starter battery The starter battery is in the battery recess in the driver’s footwell. Removing/installing the floor covering in the driver's footwell To install: place floor covering 1 into the driver’s footwell. Warning Removing the battery cover in the driver’s footwell G The movement of the pedals must not be obstructed. The vehicle’s operating and road safety are otherwise jeopardized.
Practical hints Battery Remove cover 1 upward. Disconnecting the auxiliary battery* Open the hood ( page 185). Removing the battery Starter battery Disconnect the battery ( page 337). Starter battery in the driver’s footwell Loosen the negative terminal of the battery first and remove it so that the negative terminal cannot come into contact with the pole terminal. Remove the cover from the positive terminal.
Practical hints Battery Auxiliary battery* in the engine compartment Disconnect the battery ( page 337). Unscrew the bolts preventing the battery from moving around in the engine compartment. Remove the battery retainer and take out the battery. 3 Retainer 5 Loosen the bolts of retainer 3 preventing the battery from moving around. Pull retainer 3 upward and slide the battery out of its anchorage in the direction of travel. Fold the clip upward and remove the battery from the battery recess.
Practical hints Battery Recharging the battery Recharge the removed battery. Observe the notes in the operating instructions for your battery charger. Reinstall the battery in the reverse order. !CAUTION Only charge the installed battery using a battery charger tested and approved by the manufacturer. These devices allow you to charge the battery while it is installed. The vehicle’s electronics system may otherwise be damaged. Warning G Only charge the battery in well-ventilated areas.
Practical hints Jump-starting Jump-starting If the starter battery in the battery recess in the driver’s footwell is discharged, the engine can be jump-started from another vehicle using jump leads. For this purpose, the vehicle is equipped with a jump-starting connection point. i 5 The auxiliary battery* in the engine compartment is not suitable for jumpstarting operations.
Practical hints Jump-starting Using red positive terminal clamp 1 of the jumper cable, slide the red protective cap of the jump-starting connection point back with a clockwise turn and connect the positive terminal clamp of the jumper cable to the positive terminal of the jump-starting connection point. i Do not connect the jumper cable to the auxiliary battery* in the engine compartment. This is not suitable for jumpstarting operations. Run the other vehicle’s engine at idling speed.
Practical hints Towing Towing Warning G Tow the vehicle using a rigid towing bar if: the engine is not running, Installing /removing the towing eye The fixture for the front towing eye is located behind the cover in the bumper on the right-hand side when viewed in the direction of travel. there is a malfunction in the power supply or the vehicle’s electrical system. Do not tow the vehicle if the key cannot be turned in the ignition lock.
Practical hints Towing Return the towing eye and the wheel wrench to the vehicle tool kit. i Deactivate the automatic locking while driving function when towing ( page 64). You could otherwise become locked out when pushing or towing the vehicle. Towing out a vehicle that is stuck Take great care when attempting to tow the vehicle free if its drive wheels have become embedded in loose earth or mud, particularly if the vehicle is loaded. Tow the vehicle smoothly and straightahead.
Practical hints Towing In the event of a malfunction in the electrical system If the battery is malfunctioning, the automatic transmission will be locked in position P. To shift the automatic transmission to position N, you must provide power to the vehicle’s electrical system in the same way as jump-starting ( page 340). Have the vehicle transported on a transporter or trailer.
Practical hints Fuses Fuses Warning G Only use fuses of the amperage recommended by the manufacturer. Any authorized Sprinter Dealer will be happy to advise you. Do not attempt to repair or bridge blown fuses. Main fuse box The fuse box is in the footwell on the lefthand side of the vehicle. i The fuse allocation chart for the fuse boxes is in the vehicle document wallet in the glove box and names all the numbered fuses. To open: release 1 the quick-release lock and remove the cover.
Practical hints Fuses 5 346
Practical hints Fuses No. Consumer 1 Horn 2 Electric steering lock ESTL (electronic ignition switch EIS) 3 Terminal 30 Z, vehicles with gasoline engine/electronic ignition switch EIS/instrument cluster Amp. No. Consumer 15 A 15 Front heating system 25 A 16 Terminal 87 (1) 17 Airbag control unit 10 A 18 Terminal 15 vehicle, brake lamp switch 7.5 A 19 Interior lights 7.
Practical hints Fuses No. Consumer Amp. No. Consumer 15 Non MB-body electrics 10 A 16 Heating, rear heating/ Tempmatic (air-conditioning system), front/CD-player* 10 A 17 Motion detector*/convenience interior lighting*/ satellite radio* 18 Air conditioning in the rear* 1 Pre-glow relay/secondary air pump 2 Engine fan air-conditioning system 80 A 10 A 3 Signal acquisition and actuation module SAM/fuse and relay block SRB 80 A 7.
Practical hints Fuses 5 349
Practical hints Fuses No. Consumer 1 Mirror adjustment* 5A 2 Rear window wiper* 30 A 3 Reversing camera*/ telephone* 5A 4 Operating speed governor (ADR)/PTO/trailer connection unit AAG 7.5 A Terminal 87 electronic transmission control ETC, control unit 10 A 5 5 6 Unassigned 7 Electronic selector level module ESM 8 Amp. – 7.
*Technical data Genuine Sprinter parts ......... 352 Vehicle electronics ......... 354 Service products and capacities ......... 355 Rims and tires ......... 367 Tire inflation pressure ......... 369 Lashing points and carrier systems ......... 371 Vehicle identification labels .........
*Technical data Genuine Sprinter parts Genuine Sprinter parts The “Technical data” section contains important technical data regarding your vehicle. Make sure that spare parts are suitable for your vehicle. Parts that constitute a modification to the vehicle by: Every authorized Sprinter Dealer maintains a stock of genuine sprinter parts for maintenance and repair work.
*Technical data Genuine Sprinter parts Genuine sprinter parts are subjected to the most stringent quality inspections and will ensure that the vehicle is maintained at a high level of operating efficiency and safety, and that it maintains its value. Each part has been specifically designed and manufactured or selected and approved for use in Sprinter vehicles. It is therefore best to use only genuine sprinter parts.
*Technical data Vehicle electronics Vehicle electronics Tampering with the engine electronics ! Work on the engine electronics and all associated parts such as control units, sensors and connector leads should only be performed at an authorized Sprinter Dealer. Vehicle parts could otherwise wear more quickly and the vehicle’s warranty or general operating permit could be invalidated.
*Technical data Service products and capacities Service products and capacities Service products are: fuels lubricants (e.g. engine oils, transmission oils, hydraulic fluids, greases) antifreeze additives, coolant brake fluid Service products are tested for suitability in our assemblies. Approved service products meet the highest quality standards. For this reason, only use service products that have been approved for your vehicle. This is an important condition for warranty claims to be upheld.
*Technical data Service products and capacities Rinse thoroughly with plenty of water in case of contact with eyes. Consult a doctor immediately if a service product is swallowed. Change out of clothing soiled with service products immediately to avoid the risk of fire and other injuries. Fire, naked flames and smoking are therefore prohibited when handling service products due to their highly flammable nature. Keep service products out of the reach of children.
*Technical data Service products and capacities The following oils have been determined to meet the DaimlerChrysler requirements as shown below: The following oils have been determined to meet the DaimlerChrysler requirements as shown below: MB sheet MB approved engine oil MB sheet MB approved engine oil SAE MB sheet Castrol Syntec 5W-40 5W-40 229.3 Lotos Syntetic SL/SJ/ 5W-40 CF/CD 229.3 Pentosin Diesel 10W40 LA 10W-40 228.51 Castrol Syntec 0W-30 European Formula 0W-30 229.
*Technical data Service products and capacities Adding engine oil Fuels for gasoline engines Fuels !CAUTION G Diesel engine: Warning Never use any amount of engine oil for the diesel engine that does not conform to MB 229.51 or MB 229.31 specifications. Otherwise the diesel particle filter (DPF) could be damaged. Gasoline is highly flammable and poisonous. It burns violently and can cause serious injury.
*Technical data Service products and capacities Fuel requirements !CAUTION Fuel requirements Only use premium unleaded fuel: The following may lead to increased wear or engine damage: Only use commercially available vehicular ULTRA-LOW SULFUR HIGHWAY DIESEL FUEL (15 ppm SULFUR MAXIMUM). The octane number (posted at the pump) must be 91 min. It is an average of both the Research (R) octane number and the Motor (M) octane number: (R+M)/2). This is also known as the ANTI-KNOCK INDEX.
*Technical data Service products and capacities Diesel fuels containing a higher percentage of Bio diesel content will cause damage to your engine and are not approved. Damage or malfunctions resulting from poor fuel quality are not covered by the Sprinter Warranty.
*Technical data Service products and capacities At temperatures below 14 °F (–10 °C) a certain quantity of fuel flow improver may be added. These substances may only be mixed within the vehicle’s fuel tank. Warning Engine power may drop according to the proportion of fuel flow improver. For this reason, keep the percentage of fuel flow improver to the minimum necessitated by the ambient temperature.
*Technical data Service products and capacities Coolants, lubricants, etc. Service interval Product name/product number MB sheet MSNo.1 Air conditioning The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. Refrigerant R-134a — Refrigerant R-134a 361.0 Automatic transmission Automatic transmission fluid 6 10 years MOPAR® 05127382AB 60,000 mi Shell ATF 3403 (96,000 km) Shell ATF 3353 236.10 236.
*Technical data Service products and capacities Service interval Product name/product number MB sheet MSNo.1 Engine cooling system The use of aluminum components in Sprinter engines requires that anticorrosive/antifreeze specifically formulated to protect aluminum parts be used. The factory-approved service products are suitable for Sprinter engines and can be mixed with the original anticorrosion/ antifreeze filled at factory.
*Technical data Service products and capacities Service interval Product name/product number MB sheet MSNo.1 Mobil ATF+4, Exxon Mobil Corporation, or equiva- 236.3 lent 9602 Power steering Power steering, no fluid service required. Power steering fluid — MOPAR® Part No. 05013457AA, or equivalent – BP Energear Hyep DC 80W-90 Mobil Delvac Synthetic Gear Oil 75W-90 235.20 235.8 MOPAR® Part No.
*Technical data Service products and capacities Capacities Vehicle Engine with oil filter Engine oil Tank Capacity Including reserve fuel Cooling system Windshield washer/ headlamp cleaning system Coolant1 Water with MB windshield washer fluid 2500 CRD, 3500 CRD 13.21 US qt. (12.5 l) 25.0 US gal (100 l) 5.3 US gal (20 l) 10.75 US qt. approx. 7.40 US qt. (7.0 l) (10.0 l) 2500, 3500 10.04 US qt. (9.5 l) 25.0 US gal (100 l) 5.3 US gal (20 l) 7.40 US qt. approx. 7.40 US qt. (7.0 l) (7.
*Technical data Service products and capacities The vehicle will use more fuel than usual in the following conditions: Fuel consumption Environmental note H A vehicle’s CO2 emissions and fuel consumption depend on: at very low temperatures in urban traffic on short trips efficient use of fuel by the engine when towing a trailer the style of driving adopted when driving with a heavy load other non-technical factors such as environmental influences or road conditions in mountainous
*Technical data Rims and tires Rims and tires !CAUTION Only use tires which have been tested and approved for your Sprinter vehicle by the vehicle manufacturer. Tires approved by the vehicle manufacturer are developed to provide the best possible performance in conjunction with the driving safety systems on your Sprinter vehicle such as ABS, BAS, ASR or ESP®. Using tires other than those approved by the vehicle manufacturer may result in damage that is not covered by the Sprinter warranty.
*Technical data Rims and tires Vehicle Model Type 2500 3500 Rims (steel) 6.5 J x 16 5.5 J x 16 Rims (light alloy) 6.5 J x 16 – Wheel offset 2.13 in (54 mm) – 4.82 in (122.
*Technical data Tire inflation pressure Tire inflation pressure For vehicles with a gross weight capacity above 10,000 lbs (4500 kg) only. For vehicles with a gross weight capacity less than 10,000 lbs (4500 kg) observe the recommended cold tire inflation pressures listed on the tire and loading information placard on the driver’s door B-pillar ( page 210). Observe the information on recommended tyre inflation pressure in the “Operation” section ( page 210).
*Technical data Tire inflation pressure For example: If the inside temperature is 68 °F (20 °C) and the outside temperature is 32 °F (0 °C) then the cold tire inflation pressure should be increased by 3 psi (0.2 bar), which equals 1.5 psi (0.1 bar) for every 18 °F (10 °C) for this outside temperature condition. Tire Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes.
*Technical data Lashing points and carrier systems Lashing points and carrier systems Lashing points !CAUTION Observe the data on the maximum load-bearing capacity of the individual lashing points. During full-braking applications, for example, forces can be involved that are much greater than the weight force of the load. Always use several lashing points in order to distribute force absorption, and make sure that the lashing points have an equal load.
*Technical data Lashing points and carrier systems !CAUTION Roof carrier systems Maximum roof load and minimum number of pairs of roof rack supports on vehicles with: Maximum roof load Minimum number of pairs of supports Standard roof 660 lbs (300 kg) 6 Raised roof 330 lbs (150 kg) 3 The data is valid when the load is distribut- 6 ed evenly over the entire roof area. When using a shorter roof rack, reduce the load proportionately.
*Technical data Vehicle identification labels Vehicle identification labels i For certain vehicles, vehicle data cards are delivered with the vehicle. These vehicle data cards contain all the important details of your vehicle, e.g. vehicle identification number, engine number and subassembly numbers together with the model and optional equipment codes. This data is required when ordering parts and for questions of a technical nature. For reasons of security, card 1 must not be kept in the vehicle.
*Technical data Vehicle identification labels Example vehicle safety certification label (Canada vehicles) Example Engine Compartment Example incomplete vehicle safety certification label (Canada vehicles) 1. Read and observe the diesel engine oil information ( page 362).
*Technical data Vehicle identification labels Tire and loading information placard For vehicles with a gross weight capacity less than 10,000 lbs (4500 kg) only. The tire and loading information placard is located on the driver’s door B-pillar. i The data shown on the placard is for illustrative purposes only. The load limit data and seating data is specific to each vehicle and may vary from the data shown in the illustration. Refer to the placard on your vehicle for data specific to your vehicle.
Index Numerics 12 V socket . . . . . . . . . . . . . . . . . . . 170 A A ABS see Antilock Brake System Acceleration skid control (ASR) . . . 44 activating/deactivating . . . . . . . . . . 45 display message . . . . . . . . . . . . . . 291 indicator lamp . . . . . . . . . . . . 268–270 malfunction . . . . . . . . . . . . . . . . . . 270 warning lamp . . . . . . . . . . . . . . 44, 268 Accessory weight . . . . . . . . . . . . . . 228 Accident . . . . . . . . . . . . . . . . . . . . . .
Index maneuvering . . . . . . . . . . . . . . . . . one-touch gearshifting . . . . . . . . . . releasing the parking lock manually selector lever positions . . . . . . . . . shift ranges . . . . . . . . . . . . . . . . . . stopping . . . . . . . . . . . . . . . . . . . . . towing . . . . . . . . . . . . . . . . . . . . . . trailer towing . . . . . . . . . . . . . . . . . working on the vehicle . . . . . . . . . . Auxiliary heating . . . . . . . . . . . . . . . heater booster function . . . . . . . . .
Index Care of batteries . . . . . . . . . . . . . . . 196 Care of the vehicle . . . . . . . . . . . . . 241 after driving off-road or on construction sites . . . . . . . . . . . . . 246 Carrier systems . . . . . . . . . . . 162, 372 Catalytic converter . . . . . . . . . . . . . 181 CD player/CD changer . . . . . . . . . . . 94 Cell phone . . . . . . . . . . . . . . . . . . . . 171 Center console . . . . . . . . . . . . . . . . . 18 switch unit . . . . . . . . . . . . . . . . . . . .
Index temperature gauge (vehicle with steering wheel buttons) . . . . . . . . . . . . . . . . . . . . . 255 Cornering lamps changing bulbs . . . . . . . . . . . . . . . . 307 Correct use . . . . . . . . . . . . . . . . . . . . . 7 Cruise control . . . . . . . . . . . . . . . . . 147 deactivating . . . . . . . . . . . . . . . . . . 149 display message . . . . . . . . . . . . . . 287 downhill gradients . . . . . . . . . . . . . 148 lever . . . . . . . . . . . . . . . . . . . . . . . . 148 malfunction . . . .
Index driving in wet conditions . . . . . . . . driving on flooded roads . . . . . . . . in winter . . . . . . . . . . . . . . . . . . . . . overrun cut-off . . . . . . . . . . . . . . . . programmed maximum speed . . . . pulling away . . . . . . . . . . . . . . . . . . steering . . . . . . . . . . . . . . . . . . . . . 117 117 235 117 180 112 116 E E EBV see Electronic brake force distribution Electric sliding door . . . . . . . . . . . . . 57 programming the key . . . . . . . . . . . .
Index F F Fastening seat belts see Wearing seat belts Fault memory see Malfunction memory Fax machine . . . . . . . . . . . . . . . . . . 183 Fire extinguisher . . . . . . . . . . . . . . . 299 First-aid kit . . . . . . . . . . . . . . . . . . . 299 Flat tire changing a wheel . . . . . . . . . . . . . . 320 Premium tire sealant . . . . . . . . . . . 326 Flow improvers . . . . . . . . . . . . . . . . 361 Folding seat . . . . . . . . . . . . . . . . . . . . 74 Folding table in the backrest . . . . .
Index seats . . . . . . . . . . . . . . . . . . . . . . . . 73 windshield . . . . . . . . . . . . . . . . . . . 127 Heater booster function . . . . . . . . 137 Heater booster system . . . . . . . . . 138 Heating rear window . . . . . . . . . . . . . . . . . . 128 seat . . . . . . . . . . . . . . . . . . . . . . . . . 73 windshield . . . . . . . . . . . . . . . 127, 134 High-beam headlamps . . . . . . . 77, 307 changing bulbs . . . . . . . . . . . . . . . 307 High-pressure cleaners . . . . . . . . .
Index K K Key battery check lamp . . . . . . . . . . . . . 53 buttons . . . . . . . . . . . . . . . . . . . . . . . 53 changing the batteries . . . . . . . . . . 315 lost . . . . . . . . . . . . . . . . . . . . . . . . . 260 malfunction . . . . . . . . . . . . . . 259–261 problems . . . . . . . . . . . . . . . . . . . . 259 Key no. . . . . . . . . . . . . . . . . . . . . . . . 373 Key positions Kickdown . . . . . . . . . . . . . . . . . . . . . 123 Kilopascal . . . . . . . . . . . . . . . . . . . .
Index Messages bulbs . . . . . . . . . . . . . . . . . . . 292, 293 coolant . . . . . . . . . . . . . . . . . . . . . . 292 doors . . . . . . . . . . . . . . . . . . . . . . . 298 engine oil level . . . . . . . . . . . . 296–297 reserve fuel . . . . . . . . . . . . . . . . . . 297 telephone . . . . . . . . . . . . . . . . . . . . 291 washer fluid . . . . . . . . . . . . . . 287, 298 Mirrors exterior mirrors . . . . . . . . . . . . . . . 125 rear-view mirror . . . . . . . . . . . . . . .
Index Parking lamps . . . . . . . . . . . . . . . . . . 77 changing bulbs . . . . . . . . . . . . . . . . 308 Parking lock see Automatic transmission Parktronic . . . . . . . . . . . . . . . . 150, 244 cleaning the sensors . . . . . . . . . . . 244 indicator lamp . . . . . . . . . . . . . . . . 262 malfunction . . . . . . . . . . . . . . . . . . 262 range of the sensors . . . . . . . . . . . 150 roll-back warning . . . . . . . . . . . . . . 152 switching on/off . . . . . . . . . . . . . .
Index Removing/installing the floor covering in the driver’s footwell . . . . . . . . . . 336 Reserve warning indicator (fuel) . . 276 Residual heat mode . . . . . . . . . . . . 134 problems . . . . . . . . . . . . . . . . . . . . 267 Restraint system . . . . . . . . . . . . . . . 24 airbags . . . . . . . . . . . . . . . . . . . . . . . 25 belt force limiters . . . . . . . . . . . . . . 30 child restraint systems . . . . . . . . . . 37 display message . . . . . . . . . . . . . .
Index Side lamps . . . . . . . . . . . . . . . . . . . . 307 Side marker lamps . . . . . . . . . . . . . 307 changing bulbs . . . . . . . . . . . . . . . . 312 Side wall . . . . . . . . . . . . . . . . . . . . . . 230 Side windows cleaning . . . . . . . . . . . . . . . . . . . . . 244 operating . . . . . . . . . . . . . . . . . . . . 144 Sliding door closing aid . . . . . . . . . . . . . . . . . . . . 57 electric . . . . . . . . . . . . . . . . . . . . . . . 57 locking/unlocking from the inside . . . . . .
Index T T Tachometer . . . . . . . . . . . . . . . . . . . . 85 Tail lamps . . . . . . . . . . . . . . . . . . . . 309 changing bulbs . . . . . . . . . . . . . . . 310 perimeter lamp . . . . . . . . . . . . . . . 309 Tank flap . . . . . . . . . . . . . . . . . . . . . . 86, 184 malfunction . . . . . . . . . . . . . . 251–252 reserve fuel, display message . . . . 297 Technical Data Tire inflation pressure . . . . . . . . . . 369 Telephone . . . . . . . . . . . . . . . . 171, 183 display message . . . . . .
Index loading the vehicle . . . . . . . . . . . . . 205 low tire pressure indicator . . . . . . . 278 maximum load . . . . . . . . . . . . . . . . 231 messages in the multifunction display . . . . . . . . . . . . . . . . . . . . . . 278 ply composition and material used . . . 230 problems under/overinflation 221, 222 radial-ply tires . . . . . . . . . . . . . . . . 201 retreads . . . . . . . . . . . . . . . . . . . . . 200 rotating . . . . . . . . . . . . . . . . . 204, 231 seating capacity . . . . . . . .
Index closing . . . . . . . . . . . . . . . . . . . . . . . 52 correct use . . . . . . . . . . . . . . . . . . . . 7 data cards . . . . . . . . . . . . . . . . . . . 373 identification number . . . . . . . . . . 373 leaving in storage . . . . . . . . . . . . . 265 locking with key . . . . . . . . . . . . . . . . 55 locking/unlocking centrally . . . . . . . 64 opening . . . . . . . . . . . . . . . . . . . . . . 52 with remote control . . . . . . . . . . . 54 with the key . . . . . . . . . . . . . . . . .
2007 SPRINTER 81-326-0799 Second Edition Printed in U.S.A.
