SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 3 4 INSTRUMENT PANEL AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 5 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .10 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .16 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .10 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .19 ▫ Sentry Key — If Equipped . . . . . . . . . . . . . . . .10 䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . .20 䡵 Ignition And Steering Lock . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Security Alarm System — If Equipped . . . . . . . . .26 ▫ Second Row Center Seat Belt . . . . . . . . . . . . . .42 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .27 ▫ Rear 60/40 Seat Third Row Center Three Point Belt — If Equipped . . . . . . . . . . . . . . . . . . . . .43 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .27 䡵 Remote Starting System — If Equipped . . . . . . . .28 䡵 Liftgate . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . .75 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 ▫ Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number. NOTE: Integrated keys (key and key fob combined) must be cut by the dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 on the remaining transmitters will work. If the vehicle is moving 5 mph or more, then all the transmitter buttons are disabled for all keys. NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IGNITION AND STEERING LOCK In the LOCK position, the steering and ignition systems are locked to provide anti-theft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle, if the steering wheel is locked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! The key cannot be turned to LOCK until the selector is in the PARK position. Do not attempt to pull the shift lever out of PARK after the key is in the LOCK position. NOTE: The steering wheel will lock when the key is removed, and the steering wheel is turned around 115 degrees clockwise or 65 degrees counterclockwise from the center position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 DOOR LOCKS WARNING! Manual Door Locks All the doors can be “manually” locked from the inside by pushing down the door lock plunger, located at the rear of the door. Both front doors may be opened from the inside with the door lock plunger in the down or locked position. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks Power Door Lock Switch Operation Power Door Lock Switches Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 As a safety feature the doors will not lock when using the door lock switches during the following conditions: • The driver’s door is open while the key is in the ignition. Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE occur only after the vehicle has been shifted into the Park position after the vehicle has been driven (shifted out of Park and all doors closed). 4. Within 15 seconds, cycle the key from the OFF position to the ON position a minimum of four times ending in the OFF position (do not start the engine). This feature will not operate if there is any manual operation of the power door locks (Lock or Unlock). 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the childprotection door lock system. 2 Child Lock Details Child Lock Location To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! REMOTE KEYLESS ENTRY Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: Your vehicle’s keyfob may have three, four or five buttons (shown), depending on the optional features purchased with your vehicle. The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure: This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a minimum of 66 feet (20 meters) using a hand held radio transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. To lock the doors and liftgate: Press and release the LOCK button on the key fob to lock all doors and liftgate. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once. Horn Chirp Programming The horn chirp feature will be shipped from the assembly plants activated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Flash Lamps with Lock Programming 1. Press and hold the UNLOCK button on the key fob. 2. After holding the UNLOCK button for four seconds, also press the LOCK button within 6 seconds. A single chime will sound to indicate that this feature has changed. 3. Release both buttons at the same time. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the UNLOCK button on the key fob. 6. After holding the UNLOCK button for four seconds, also press the PANIC button within 6 seconds. 7. When a single chime is heard release both buttons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Battery Replacement The recommended replacement battery is CR2032. 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 To Set the Alarm: The alarm will set when you use the power door locks or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the security light in the instrument cluster will flash rapidly to signal that the system is arming. The security light in the instrument panel cluster will flash rapidly for about 15 seconds to indicate that the alarm is being set.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNLOCK button or by inserting a programmed Sentry Key into the ignition and turning the key to the ON position. REMOTE STARTING SYSTEM — IF EQUIPPED Your Dodge Durango may be equipped with a remote starting system, which will allow the vehicle to be started up to 300 feet away from the vehicle using the remote keyless entry key fob which is part of your ignition key. In order to remote start your vehicle, the hood, liftgate, and all the doors must be closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the UNLOCK button on the key fob. After the vehicle is unlocked, you have 60 seconds to enter the vehicle, insert the key in the Ignition and move it to the RUN position, otherwise the engine will cancel remote start and automatically turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When the engine is running from a Remote Start (if equipped), the vehicle must first be unlocked by pressing the keyfob UNLOCK button prior to activating the Power Liftgate otherwise the engine will stop automatically. Once unlocked, the liftgate can be opened or closed. To open the liftgate, depress the liftgate release switch located in the exterior handle and pull the liftgate open with one fluid motion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter. Press the button on the remote keyless entry transmitter twice within five seconds, to open the power liftgate. Once the liftgate is fully open, pressing the button twice within five seconds a second time will close the liftgate. the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. A beeping signal will sound two seconds before the liftgate starts to open or close. NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 (65° C). Be sure to remove any buildup of snow or ice from the liftgate before pressing any of the power liftgate switches. • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually. • If your liftgate is power closing and you put the vehicle in gear, the liftgate will continue to power close. However, vehicle movement may result in a detection of an obstruction.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows Power Window Switches Power Window Switches The control on the left front door has up-down switches that give you finger tip control of all four power windows. There is a single opening and closing switch on the passenger doors for passenger window control.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer. NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF. 2 Auto Down The driver’s window switch has an Auto Down feature. Push the window switch past the first detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, knee bolsters, front airbags for both the driver and front passenger, and if equipped left and right side curtain airbags for the driver and passengers seated next to a window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! Adjustable Upper Shoulder Belt Anchorage In the front and second row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in the desired position. Pull the seatback forward to ensure that it is locked in the upright position. WARNING! A 20% seatback that is not fully latched in the upright position will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Rear 60/40 Seat Third Row Center Three Point Belt — If Equipped The center three point seat belt for the third row rear seat may be disconnected to allow the 60% seat back to easily fold down. The keyed-buckle latch plate (small latch plate at the end of the belt) can be detached from the keyed seat belt buckle (buckle without a red release button) located on the left inboard side of the third row bench seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To reattach the seat belt to the third row center seat, pull the small (keyed buckle) latch plate forward from the headliner slots and insert it into the keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belt system in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 buckled. A chime will sound immediately (once the feature has toggled). If during this time the ignition switch is turned out of the ON position or the timer expires, programming mode will be cancelled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 4. If your vehicle has window bags, do not lean against the door or window, airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided in the ⬙If You Need Customer Assistance⬙ section later in this owner’s manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag System Components The airbag system consists of the following: • Occupant Restraint Controller • Driver and Front Passenger Seat Belt Pretensioners • Occupant Classification System (OCS) for the Front Passenger Seat • Side Remote Acceleration Sensors (If Equipped) − Occupant Classification Module • Airbag Warning Light − Passenger Airbag Disable (PAD) Indicator Light • Driver Airbag − Weight Sensors • Passenger Airbag How the Airbag System Wor
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. During a moderate-to-severe rear impact the ORC may deploy the seat belt pretensioners alone.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. • The Passenger Airbag Disable (PAD) Indicator Light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag is turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 adult passenger is properly seated in the front passenger seat. In this case, the air bag is ready to be inflated if a collision requiring an airbag occurs. For almost all properly installed rear facing child restraints, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occupant is classified by the OCS.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 sensors, a fault will occur which turns on both the PAD Indicator Light and the Airbag Warning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time. the airbag. The passenger’s front airbag gas is vented through vent holes in the sides of the airbag. In this way the airbags do not interfere with your control of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Side Impact SRS Window Bags are designed to activate only in certain side collisions. When the ORC (with side impact option) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the outside edge of the headliner out of the way and covers the window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 • Do not replace the seat cover with an aftermarket seat cover. • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar. • At no time should any supplemental restraint system (SRS) component or SRS related component or fastener be modified or replaced with any part except those which are approved by DaimlerChrysler/ Mopar.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Maintaining Your Airbag System WARNING! • • • • • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The light flickers or comes on and remains on while driving. NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control module may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 LATCH child restraint anchorage system. (See the LATCH - Child Seat Anchorage System section.) • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. If the seat belt has a automatic locking retractor, it will have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. All three second row seating positions have lower anchorages that are capable of accommodating LATCHcompatible child seats having flexible, webbing-mounted lower attachments.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Second Row Seat Right Side Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Second Row Seat Tether Anchors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Child Restraints in Third Row Seating (If Equipped) The third seating row is not capable of installing child restraints that require the use of a tether strap. There are no tether anchor provisions for the third seating row in your vehicle, the hooks in the rear floor are not designed to withstand the forces that may occur during a crash. Child Restraint Tether Anchor There are tether strap anchorages behind each seating position in the second row.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Follow the instructions below. See your dealer for help if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. SAFETY TIPS Exhaust System WARNING! Exhaust gases contain carbon monoxide, an extremely toxic gas that by itself is colorless and odorless.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Safety Checks You Should Make Outside The Vehicle: Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Fluid Leaks Check the area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .84 ▫ Automatic Dimming Mirror — If Equipped . . . .84 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Exterior Mirrors Folding Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Electric Remote-Control Mirrors . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 ▫ Third Row 60/40 Folding — If Equipped . . . . 122 ▫ Front Seat Manual Seat Adjustment . . . . . . . . 111 䡵 Driver Memory System — If Equipped . . . . . . . 125 ▫ Front Seats Manual Seat Recliners . . . . . . . . . . 112 ▫ Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory . . . . . . . 126 ▫ Manual Lumbar Support Adjustment — If Equipped . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 ▫ Automatic Headlights — If Equipped . . . . . . . 133 ▫ Headlights, Parking Lights, Panel Lights . . . . . 134 ▫ Illuminated Entry . . . . . . . . . . . . . . . . . . . . . 134 ▫ Daytime Running Lights (Canada Only) . . . . . 134 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 135 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 135 䡵 Multifunction Control Lever . . . . . . . . . . . . . . . 135 ▫ Turn Signals . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Electronic Brake Control System . . . . . . . . . . . . 146 ▫ Step Button . . . . . . . . . . . . . . . . . . . . . . . . . 157 ▫ ABS (Anti-Lock Brake System) . . . . . . . . . . . . 146 ▫ Average Fuel Economy (AVG ECO) . . . . . . . . 158 ▫ BAS (Brake Assist System) – If Equipped With ESP . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 ▫ Canadian Programming/Gate Programming . . 166 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . 170 ▫ Using HomeLink . . . . . . . . . . . . . . . . . . . . . 166 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . . 170 ▫ Erasing HomeLink Buttons . . . . . . . . . . . . . . 166 ▫ Electrical Outlet Use With Engine Off (Battery Fed Configuration) . . . . . . . . . . . . . . 171 ▫ Reprogramming a Single HomeLink Button . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Day/Night Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. Mirror Directions Remote Control Mirrors Switch To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE that the heating elements are ON. Turning Off the rear window defroster or the ignition will deactivate the heated mirrors. Automatic Dimming Driver’s Exterior Mirror — If Equipped This mirror will automatically adjust for annoying light glare from vehicles behind you. This feature is controlled by the inside mirror and can be turned off by pressing the button at the base of the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 that enables different electronic devices to connect to each other without wires or a docking station, so UConnect works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect™ system. The UConnect™ system allows up to seven cellular phones to be linked to system. Only one linked (or paired) cellular phone can be used with the system at a time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙Ready⬙ prompt or another prompt. The UConnect™ system is fully integrated with the vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Voice Command Tree Refer to “Voice Tree” at the end of this section. Help Command If you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙Help⬙ following the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help. To activate the UConnect™ system from idle, simply press the ’Phone’ button and follow audible prompts for directions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • When prompted, after the voice on beep, say ⬙Pair a Phone.⬙ • You will be asked to say a four-digit pin number which you will later need to enter into your cellular. You can enter any four-digit pin number.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Dial by Saying a Number Call by Saying a Name • Press the ’Phone’ button to begin. • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Dial.⬙ • After the ⬙Ready⬙ prompt and the following beep, say ⬙Call.⬙ • System will prompt you to say the number you want call. • System will prompt you to say the name of the person you want call. • For example, you can say ⬙234-567-8901.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the UConnect™ system will ask you which designation you wish to delete: home, work, mobile or pager. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. After confirmation, the phonebook entries will be deleted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Phone Call Features The following features can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect™ system. Check with your cellular service provider for the features that you have.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls.⬙ To combine two calls, refer to ⬙Conference Call.⬙ Place/Retrieve a Call from Hold To put a call on hold, press the ⬘Phone’ button until you hear a single beep which will indicate that the call has been placed on hold. To bring the call back from hold, press and hold the ⬘Phone’ button until you hear a single beep.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Redial • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Redial.⬙ • The UConnect™ system will call the last number that was dialed on your cellular phone. Note: this may not be the last number dialed from the UConnect™ system. Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Continue to follow the system prompts to complete language selection. • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by the word ⬙Send.⬙ For example, if required to enter your pin number followed with a pound 3 7 4 6 #, you can press the ’Voice Recognition’ button and say ⬙3 7 4 6 # Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Service When using AT&T Wireless Service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. • The selected phone will be used for the next phone call. If the selected phone is not available, the UConnect™ system will return to using the highest priority phone present in or near (approximately with in 30 feet) the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ⬘Voice Recognition’ button anytime while the list is being played and say the priority number of the phone you wish to delete. Things You Should Know About Your UConnect™ System Voice Recognition (VR) • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • UConnect™ phonebook name tag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 SEATS North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Manual Seat Adjuster Front Seats Manual Seat Recliners The bucket seats are equipped with recliners.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Manual Lumbar Support Adjustment — If Equipped The manual lumbar support adjustment lever is located on the right side of the driver seat and on the left side of the passenger’s seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To lower the head restraint, depress the release button located at the base of the head restraint and push down on the head restraint. 8 - Way Driver’s Power Seat — If Equipped The driver power seat switches are located on the left side of the driver seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the right side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjustment. The top switch controls the seatback recline adjustment. Front Heated Seats — If Equipped 3 NOTE: The 4 - way seat does not have an up/down adjustment. Heated Seat Switches This feature heats the driver and front passenger seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE passenger to select from two different levels of supplemental electrical seat heating, or no seat heating to suit their individual comfort requirements. With the ignition switch in the RUN position, depressing the heated seat switch rocker to its momentary High or Low position provides power to the heated seat element and maintains the requested temperature setting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE be folded into the down position for use as a cargo floor, or the seat can now be tumbled forward to allow access to the rear of the vehicle. To fold the 20% seatback, pull the strap forward to release the seatback. Fold the seatback down for use as an armrest or to carry cargo. When returning the seatback to the upright position, push the seatback rearward to latch the seatback. Pull the seatback forward to ensure that it is locked in the upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 WARNING! Do not drive the vehicle with the outer 40% second row seats in the tumbled position. The outer 40% second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury. 3 NOTE: The seatback must be fully folded into the down position to allow the lever to be raised enough to release the floor latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seat Bench — If Equipped To Fold The Seats Folding the third seat occurs in two stages: First the cushion is lifted and moved forward from the pockets at the front of the cushion. The cushion will rest onto the floor directly behind the second row seat. Second, the top of the back is folded forward and rests onto the cushion. The back will not fold unless the cushion has been folded forward first.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 3 Seat Cushion Movement Up And Forward Rear Seat Folded To Achieve Maximum Cargo Capacity Pull the release handles and strap on the second row seats and fold flat. After folding the third row seat, unsnap the flipper panel on the third row seatback and flip it forward on the backs of the second row seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Before returning the second row 40% seats to their upright position, always snap the third row seat flipper panel(s) back to the third row seat first. Third Row 60/40 Folding — If Equipped NOTE: The seat belt buckles are hinged to fold with the seat back. WARNING! Do not sit in the third row seat unless the cushion and back are properly engaged. Proper engagement can be verified by pushing/pulling on the upright seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 3 Third Row Seat 40% Seatback Folded Down Third Row Seat Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seat Folded Forward Third Row Seat Return Pull Strap
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 DRIVER MEMORY SYSTEM — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat position, driver’s outside mirror position, adjustable brake and accelerator pedals position, Automatic Temperature Control (ATC) temperature and radio station preset settings. Your Remote Keyless Entry transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory 5. Press and release the SET (S) button located on the driver’s door. NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store new settings. 6. Within 5 seconds, press and release memory button 1 or 2 on the driver’s door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Memory Position Recall NOTE: • The driver’s seat belt must be unbuckled to recall memory positions. • The vehicle must be in Park to recall memory positions. • Not all motors may be moved at one time. Please refer to the 8-way power seat description. To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the Unlock button on the Remote Keyless Entry transmitter linked to memory position 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Within 10 seconds, press and release the UNLOCK button on the Remote Keyless Entry transmitter. To disable another transmitter linked to either memory position, repeat steps 1-3 for each transmitter. NOTE: The capability to link Remote Keyless Entry transmitters to memory is enabled when delivered from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 the seat is positioned rearward enough and no benefit from moving the seat any farther rearward. NOTE: The Easy Exit Easy Entry feature is not enabled when delivered from the factory. The Easy Exit Easy Entry feature may be enabled (or later disabled) by a qualified DaimlerChrysler service representative. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then push the safety latch lever to the left. It is located between the grille and hood opening right of the center. NOTE: Ensure hood prop rod is fully seated into clip before closing hood to prevent damage to grille. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 LIGHTS 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights all the way down to the OFF detent will cause all the interior lights to go out. This allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 If the headlights remain on while the ignition is cycled off, the exterior lights will automatically turn off after 8 minutes. If the headlights are turned on and left on for 8 minutes while the ignition is off, the exterior lights will automatically turn off. NOTE: Battery Saver mode is cancelled if the ignition is ON. NOTE: While the engine is running, the system will deactivate the Fog Lights and Heated seats if a low battery system voltage is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Panel Lights When the headlight switch is rotated to the first position to the right, the parking lights, taillights, side marker lights, license plate light and instrument panel lights are all turned on. The headlights will turn ON when the switch is rotated to the second position. Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Lights-on Reminder If the headlights, parking lights, or courtesy lights are left On, after the ignition is turned Off, a continuous fast chime will sound when the driver’s door is opened. Fog Lights — If Equipped position and pressing the fog light button. The fog lights will operate only when the parking lights are ON or when the vehicle headlights are ON low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate. You can signal a lane change by moving the lever partially up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam. Windshield Wipers 3 The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE deep snow, sand, or gravel turn the system Off to improve traction. If the vehicle is 4WD, use 4HI position. When the ESP is switched off, the ESP/TCS Indicator light in the instrument cluster comes on. When the ESP is switched on, the Indicator light goes out. To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, switch off the ESP by pressing the button switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 WARNING! DRIVER ADJUSTABLE PEDALS — IF EQUIPPED Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. 3 The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, up to move the pedals toward the driver or down to move the pedals away from the driver. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate speed control without erasing the memory. Pushing the ON/OFF button to the OFF position or turning off the ignition erases the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it. To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above (refer to the table below for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Functions Engage Speed Minimun RESUME Speed ACCEL Increase DECEL Decrease Dropout Speed 3.7L 35 mph (56 km/h) 30 mph (50 km/h) 2 mph (3km/h) 1 mph (2 km/h) 30 mph (50 km/h) To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE applies optimum pressure to the brakes. The system applies optimum pressure to the brakes in emergency braking conditions. This can help reduce braking distances. The BAS complements the antilock brake system (ABS). Applying the brakes very quickly results in the best BAS assistance. To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 TCS (Traction Control System) – if equipped with ESP This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance that wheel lift or rollover may occur. • ERM can not prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. ESP/TCS Indicator Light The ⬙ESP/TCS Indicator Light⬙ starts to flash as soon as the tires lose traction and the ESP system becomes active. The ⬙ESP/TCS Indicator Light⬙ also flashes when TCS is active. If the ⬙ESP/TCS Indicator Light⬙ begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Range (4WD Models) or 2WD Models ON This is the normal operating mode for ESP in 4WD high range and in 2WD vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD low range or neutral back to 4WD high range, the ESP system will be in this mode. This mode should be used for most all driving situations. ESP should only be turned to “Partial Off” for specific reasons as noted below.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 situation requiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP on by momentarily depressing the “ESP Control Switch”. This may be done with the vehicle is in motion. function returns to provide the stability feature at speeds above 30 mph (48 km/h). The ABS is in a special Off-Road mode that allows too look wheels at lower speed if gravel is detected to gain stopping distance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In the Partial Off mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. ESP/BAS Warning Lamp and ESP/TCS Indicator Light The malfunction indicator for the ESP is combined with the BAS indicator.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 OVERHEAD CONSOLE The overhead console has the following features: Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE COMPASS/TEMPERATURE MINI-TRIP COMPUTER This feature allows you to choose between a compass/ temperature display and one of four trip conditions being monitored. RESET Button US/M Button Use this button to change the display from U.S. to metric measurement units. When this button is pressed you will hear a confirmation beep. Use this button to reset the following displays: Average Fuel Economy Trip Odometer Elapsed time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Global Reset If the RESET button and STEP button are pressed at the same time and held for 3 seconds (you will hear a confirmation beep) and the Global Reset feature will reset the distance to empty (using a default fuel economy value), fuel economy, trip odometer, and elapsed time displays. Step Button 3 Use this button to choose or cycle through the four trip conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is connected or disconnected).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 C/T Button Compass/Temperature Display WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage. Use this button to select a readout of the outside temperature and one of eight compass headings that indicate the direction in which the vehicle is facing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After completing one 360° turn, with the vehicle traveling less than 5 mph (8 km/h), in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally. symbol is displayed complete one 360 degree turn in an area free from large metal objects or power lines. The CAL symbol will turn off and the compass will function normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause serious injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held transmitter buttons. Do not release the buttons until step 4 has been completed. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Programming⬙ section. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 constantly, programming is complete and your device should activate when the HomeLink button is pressed and released. 7. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button. (The name and color of the button may vary by manufacturer.) NOTE: To program the remaining two HomeLink buttons, begin with ⬙Programming⬙ step two. Do not repeat step one. NOTE: There are 30 seconds in which to initiate step eight.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter signals to ⬙time-out⬙ (or quit) after several seconds of transmission which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to ⬙time-out⬙ in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 • Press and hold the two outer HomeLink buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with ⬙Programming⬙ - step 2. Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink威 is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 condition until the switch is pushed forward again. To close fully, hold the switch in the forward position until the glass movement has stopped. The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open. WARNING! Never leave children in a vehicle, with the keys in the ignition switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The fuse block is located in the left side kick panel behind a removable cover near the park brake pedal. A fuse puller is attached to the inside surface of the fuse panel cover to aid in removing fuses, if necessary.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 The coin slots are located under the instrument panel center stack. Cup Holders The Durango has 8 cupholders. Four are located in the center console, two are located in the second row armrest, and two are located in the left hand quarter panel for third row occupants. The four cupholders located in the center console may be removed for cleaning.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE FACTORY INSTALLED ROOF LUGGAGE RACK NOTE: Crossbars are offered by Mopar威 accessories. External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the maximum vehicle load capacity. The load carried on the roof when equipped with a luggage rack must not exceed 68 kg (150 lbs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 CAUTION! WARNING! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack Cautions when carrying cargo on your roof rack.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO MANAGEMENT SYSTEM—IF EQUIPPED The cargo management system consists of a removable cargo liner and removable cargo organizer. Cargo Organizer To open the side cover, pull on the cover latch. To open the organizer base pull on the center latch. To remove the organizer from the vehicle, pull the right hand side of the organizer towards you so that the right pin slides out of the slot in the vehicle.
INSTRUMENT PANEL AND CONTROLS CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 181 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 182 䡵 Instrument Cluster Description . . . . . . . . . . . . . 183 䡵 Radio Reception Information . . . . . . . . . . . . . . . 191 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 191 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 192 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Vehicle Entertainment Systems (VES) Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 ▫ Operating Instructions - Radio Mode . . . . . . . 201 ▫ Operation Instructions - (CD Mode For CD Audio Play) . . . . . . . . . . . . . . . . . . . . . . 206 ▫ Load/Eject Button (CD Mode For CD Audio Play) . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 179 ▫ PTY Button ⬙Scan⬙ . . . . . . . . . . . . . . . . . . . . . 218 ▫ Front Mode Control . . . . . . . . . . . . . . . . . . . 224 ▫ PTY Button ⬙Seek⬙ . . . . . . . . . . . . . . . . . . . . . 219 ▫ Rear Temperature Control — If Equipped . . . . 226 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 219 ▫ Rear Window Defrosting And Rear Window Washer/Wiper . . . . . . . . . . . . . . . . . . . . . . . 227 ▫ Reception Quality . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . . 237 ▫ Rear Window Wiper/Washer . . . . . . . . . . . . . 237 ▫ Rear Window Defrosting . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 181 INSTRUMENTS AND CONTROLS 4
INSTRUMENT PANEL AND CONTROLS Instrument Cluster
INSTRUMENT PANEL AND CONTROLS 183 INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. Temperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operating satisfactorily.
INSTRUMENT PANEL AND CONTROLS left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. 7. Fog Light Indicator — If Equipped This light shows when the fog lights are ON. 4. Low Fuel Warning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less. 8. Coolant Temperature Light This light warns of an overheated engine condition. For a bulb check, this light will come on momentarily when the ignition is turned On.
INSTRUMENT PANEL AND CONTROLS 185 CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off. If the if the light remains on, turn the engine off immediately, and call for service. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant.
INSTRUMENT PANEL AND CONTROLS 13. ABS Warning Light This light monitors the Anti-Lock Brake System which is described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for approximately 3 seconds. If this light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. See your authorized dealer immediately.
INSTRUMENT PANEL AND CONTROLS 187 range (PRND21). If the PRNDL displays only the characters PRND21 (no boxes) have the system checked by an authorized dealer. 18. Odometer The odometer shows the total distance the vehicle has been driven. 17. Trip Odometer The trip odometer shows individual trip mileage. To toggle between the odometer and the trip odometer, press the Odometer/Trip Odometer Button. To reset the Trip Odometer, press and hold the button while in trip mode, until the Trip Odometer resets.
INSTRUMENT PANEL AND CONTROLS ⬙ESP/TCS Indicator Light⬙ also flashes when TCS is active. If the ⬙ESP/TCS Indicator Light⬙ begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. The “ESP/ TCS Indicator Light” becomes illuminated when the ESP-Off button has been pressed or ESP is only partially available caused by lack of engine management or brake thermal model. 20.
INSTRUMENT PANEL AND CONTROLS 189 NOTE: A chime will sound if the vehicle is rolling and a door has been opened. 23. BRAKE System Warning Light The red “BRAKE” warning light will come on when the ignition key is first turned on, and stay on briefly as a bulb check. If the bulb does not come on during starting, have the bulb repaired promptly. If the light stays on, it may be an indication that the parking brake has not been released, or there is a low brake fluid level.
INSTRUMENT PANEL AND CONTROLS driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible. NOTE: • ⬙The ⬙ESP/TCS Indicator Light⬙ and the ⬙ESP/ BAS Warning Lamp⬙ come on momentarily each time the ignition switch is turned ON. • The ESP Control System will make buzzing or clicking sounds when it is actively operating. 26. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system.
INSTRUMENT PANEL AND CONTROLS 191 27. Airbag Indicator The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned ON. If the light does not come on when the ignition is first turned on, or the light stays on or comes on while driving, have the airbag system checked by an authorized dealer. 28. 4LO Indicator Indicates when transfer case is in 4LO position. 29.
INSTRUMENT PANEL AND CONTROLS another. Noise from storms and power lines can also interfere with AM reception. Reducing the treble can reduce some of the noise. FM Reception FM Stereo signals produce better sound quality than AM signals. However, FM signals will only travel approximately 10 to 40 miles (16 to 64 km). Tall structures or hills can cause interference with FM signals causing the sound to cut out. ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio.
INSTRUMENT PANEL AND CONTROLS 193 SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
INSTRUMENT PANEL AND CONTROLS Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player or Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selection.
INSTRUMENT PANEL AND CONTROLS 195 Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side Tune/Audio control. 5. To exit, press any button/knob or wait 5 seconds.
INSTRUMENT PANEL AND CONTROLS Press the rotary TUNE control a fourth time and BAL will be displayed. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory. Press the rotary TUNE control a fifth time and FADE will be displayed.
INSTRUMENT PANEL AND CONTROLS 197 Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display. If the volume control is ON, the unit will switch to CD mode and begin to play.
INSTRUMENT PANEL AND CONTROLS SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear.
INSTRUMENT PANEL AND CONTROLS 199 Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, cassette player or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will be displayed.
INSTRUMENT PANEL AND CONTROLS RW/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. Mode Button (Auxiliary Mode) Press the mode button repeatedly to select between the CD player or Satellite Radio (if equipped). SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
INSTRUMENT PANEL AND CONTROLS 201 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
INSTRUMENT PANEL AND CONTROLS will return. Rotating the volume control, turning the radio ON/OFF, or turning OFF the ignition will also return the sound from the speakers Time Button Press the time button and the time of day will be displayed for 5 seconds. NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone.
INSTRUMENT PANEL AND CONTROLS 203 RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control clockwise to increase or counter-clockwise to decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes.
INSTRUMENT PANEL AND CONTROLS turning the TUNE rotary knob within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
INSTRUMENT PANEL AND CONTROLS 205 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
INSTRUMENT PANEL AND CONTROLS Operation Instructions - (CD MODE for CD Audio Play) CAUTION! NOTE: The ignition switch must be in the ON or ACC position to operate the radio. This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
INSTRUMENT PANEL AND CONTROLS 207 SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD MODE for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will be displayed.
INSTRUMENT PANEL AND CONTROLS Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
INSTRUMENT PANEL AND CONTROLS 209 RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature.
INSTRUMENT PANEL AND CONTROLS • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files).
INSTRUMENT PANEL AND CONTROLS 211 MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
INSTRUMENT PANEL AND CONTROLS Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file. LOAD/EJECT Button (CD Mode for MP3 Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded.
INSTRUMENT PANEL AND CONTROLS 213 MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the MSG or INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file.
INSTRUMENT PANEL AND CONTROLS Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s Manual. SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES威) (If Equipped) Refer to separate Video Entertainment System (VES威) Guide.
INSTRUMENT PANEL AND CONTROLS 215 menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America. Refer to your “Navigation User’s Manual” for detailed operating instructions. Operating Instructions — Satellite Radio (If Equipped) Refer to your “Navigation User’s Manual” for detailed operating instructions.
INSTRUMENT PANEL AND CONTROLS System Activation NOTE: Your vehicle’s radio must be on and in satellite mode when the activation process takes place. To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Your Vehicle Identification Number.
INSTRUMENT PANEL AND CONTROLS 217 ESN/SID Access With RAQ and RAK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With REC Navigation Radios Please refer to your Navigation User’s Manual.
INSTRUMENT PANEL AND CONTROLS Selecting a Channel Press and release the SEEK or TUNE knob to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Storing and Selecting Pre-Set Channels In addition to the 12 AM and 12 FM pre-set stations, you may also commit 12 satellite stations to push button memory.
INSTRUMENT PANEL AND CONTROLS 219 one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Reception Quality Satellite reception may be interrupted due to one of the following reasons. PTY Button ⴖSEEKⴖ When the desired program is obtained, press the ⬙SEEK⬙ button within five seconds. The channel will change to the next channel that matches the program type selected.
INSTRUMENT PANEL AND CONTROLS REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push button in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to Radio or CD.
INSTRUMENT PANEL AND CONTROLS 221 The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set push-buttons. COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: CD Player Pressing the top of the switch once will go to the next track on the CD.
INSTRUMENT PANEL AND CONTROLS NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have theft protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio.
INSTRUMENT PANEL AND CONTROLS 223 Air Conditioning Operation To turn the air conditioning On or Off perform the following steps: • Position the mode control button to the desired airflow setting. • Set the front blower control to any desired speed. • Press the Snowflake (A/C) button which is located to the right of the temperature control slide. An indicator light on the Snowflake (A/C) button shows that the air conditioning is On.
INSTRUMENT PANEL AND CONTROLS Front Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots and give an even blend of both modes.
INSTRUMENT PANEL AND CONTROLS 225 NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Defrost Outside air is primarily directed to the windshield through the defroster outlet located at the base of the windshield and side window demist outlets. Heat (Floor) Outside air flows primarily through the floor outlets located under the instrument panel.
INSTRUMENT PANEL AND CONTROLS Temperature Control The temperature of the air is controlled by a slide located on the top center of the control panel. Move the slide left or right to change the temperature. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
INSTRUMENT PANEL AND CONTROLS 227 mode on the front control will give you air from the outlets in the headliner in the rear. Floor mode in the front will give you floor in the rear. Rear Window Defrosting and Rear Window Washer/Wiper See the “Rear Window Features” section of this book. Automatic Temperature Control (ATC) — If Equipped The control can be turned on by pressing the POWER button. When the control is turned on, it will be in the last mode prior to being turned off.
INSTRUMENT PANEL AND CONTROLS The ATC system uses an infrared sensor located in the overhead console to measure the temperature of the driver. Based on the sensor input, the system will automatically control comfort by varying the temperature, fan speed, and mode. This maintains a comfortable temperature, even under changing conditions. It is important that the infrared sensor is kept clean and that objects are not blocking the sensor.
INSTRUMENT PANEL AND CONTROLS 229 Manual Control (ATC) You also may choose to customize your comfort by selecting the fan speed and mode manually. Pressing the fan speed button or any mode button places the system into manual operation. While in manual operation there are six fan speeds available and the choice of any mode. The airflow temperature is adjusted automatically to maintain the desired comfort level. You can adjust the temperature by pressing the + or – TEMP rocker switch.
INSTRUMENT PANEL AND CONTROLS Manual control of Recirculation is possible only in Panel, Floor, and Bi-Level modes. It will not operate in Mix, or Defrost modes. The recirculation symbol will flash three times indicating recirculation is not available in these modes. NOTE: If the interior of the windows begin to fog, press the recirculate button to return to outside air. Some conditions will cause captured interior air to fog windows when in recirculate mode.
INSTRUMENT PANEL AND CONTROLS 231 the A/C snowflake button has not been pressed. This dehumidifies the air to help dry the windshield. Rear Temperature Control (ATC) The “REAR” button cycles through the following modes: the rear control located in the rear of the center floor console as described under the ⬙Rear Zone Climate Control.⬙ NOTE: The display will show “CONTROL IN REAR.
INSTRUMENT PANEL AND CONTROLS Rear Zone Climate Control — If Equipped Headliner air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knobs on the outlets to one side will shut off the airflow. The rear compartment control uses two rotary knobs: one for the temperature control and the other for the fan speed control.
INSTRUMENT PANEL AND CONTROLS 233 Rear Rotary Blower Control The second row seat occupants have control of the rear blower speed, only when the front control unit is in the “REAR CONTROL” position or CONTROL IN REAR⬙ for ATC.⬙ The rear blower switch has an “Off” position and a range of blower speeds. Rotating the rear blower control clockwise will increase the blower speed.
INSTRUMENT PANEL AND CONTROLS Front Unit to Rear Unit Chart If the Front Control is selected Panel Bi-Level • Between Bi-Level Floor Floor Mix Defrost Rear Airflow will come from Headliner Headliner Bi-Level Floor Floor Floor Operating Tips Fast Cooldown For a fast cooldown, set the blower fan to the highest setting, set the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
INSTRUMENT PANEL AND CONTROLS 235 and blower speed to maintain comfort. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging.
INSTRUMENT PANEL AND CONTROLS Operating Tips Chart
INSTRUMENT PANEL AND CONTROLS 237 REAR WINDOW FEATURES Rear Window Wiper/Washer 4 A rotating switch located on the climate control panel turns the rear wiper On or Off. Pressing the rotating switch inward activates the rear window washer. Rotating the switch will enable one of five intermittent delay times for the rear wiper. The delay times range from 20 to 1 second.
INSTRUMENT PANEL AND CONTROLS If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume operation. Rear Window Defrosting A push-button type switch is located in the climate control panel. Press the switch and the rear window defroster and electric remote control heated mirrors (if equipped) will turn On. An amber indicator on the push-button will light when the defroster is turned On.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 242 ▫ Shifting Procedure - NV 144 Transfer Case . . . 252 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 242 ▫ NV 244 Generation II Transfer Case Operating Information / Precautions . . . . . . . . . . . . . . . 253 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 242 ▫ Engine Block Heater — If Equipped . . . . . . . . 244 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 264 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 280 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 264 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 281 ▫ Tire Identification Number (TIN) . . . . . . . . . . 268 䡵 Supplemental Tire Pressure Information – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 ▫ Tire Loading And Tire Pressure . . . .
STARTING AND OPERATING 241 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 289 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . . 299 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 290 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 300 䡵 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 291 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 305 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Automatic Transmission Start the engine with the selector lever in NEUTRAL or PARK position. Apply the brake before shifting to any driving range. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
STARTING AND OPERATING 243 If Engine Fails To Start If the engine fails to start after you have followed the Normal Starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING CAUTION! Long periods of engine idling can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. Engine Block Heater — If Equipped The engine block heater warms engine coolant and permits quicker starts in cold weather.
STARTING AND OPERATING 245 AUTOMATIC TRANSMISSION Automatic Transmission The electronic PRNDL on the instrument cluster indicates the transmission gear selected. The selector lever is mounted on the right side of the steering column. To drive, move the selector lever from Park or Neutral to the desired drive position. Pull selector lever toward you when shifting into Reverse, Second, First or Park, or when shifting out of Park.
STARTING AND OPERATING WARNING! Never use Park position on an automatic transmission as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
STARTING AND OPERATING 247 it also when climbing long grades, and for engine braking when descending moderately steep grades. To prevent excessive engine speed do not exceed 45 miles per hour (72 km/h) in this range. • the engine coolant has reached normal operating temperature; “1” First For driving up very steep hills and for engine braking at low speeds 25 mph (40 km/h) or less when going down hill. To prevent excessive engine speed do not exceed 25 mph (40 km/h) in this range.
STARTING AND OPERATING If the transmission temperature gets extremely hot, the transmission will automatically select the most desirable gear for operation at this temperature. If the transmission temperature becomes hot enough the TRANS TEMP light may illuminate and the transmission may downshift out of Overdrive until the transmission cools down. After cooldown, the transmission will resume normal operation.
STARTING AND OPERATING 249 equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking. The “TOW/HAUL” light will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time restores normal operation.
STARTING AND OPERATING cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position. FOUR-WHEEL DRIVE OPERATION NV 144 Transfer Case Operating Information/Precautions The NV 144 is an electric shift transfer case and is operated by the Four-Wheel-Drive (4WD) Control Switch, which is located on the instrument panel. The NV 144 transfer case provides 2 mode positions: All-Wheel Drive (AWD) and 4-Wheel-Drive LOCK.
STARTING AND OPERATING 251 WARNING! Always engage the parking brake when powering down the vehicle if the ⴖService 4WDⴖ light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. The NV 144 transfer case is not equipped with a synchronizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place.
STARTING AND OPERATING Shifting Procedure - NV 144 Transfer Case NOTE: Delayed shifting out of 4LOCK may be experienced due to uneven tire wear, low tire pressure, or excessive vehicle loading. NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The indicator light will flash and the current transfer case position will be maintained.
STARTING AND OPERATING 253 If the key is not ON then the shift will not take place and no position indicator lights will be on or flashing. NV 244 Generation II Transfer Case Operating Information / Precautions The NV 244 Generation II is an electric shift transfer case and is operated by the 4WD Control Switch, which is located on the instrument panel.
STARTING AND OPERATING NOTE: The transfer case Neutral (N) position is to be used for recreational towing only. See Recreational Towing section for specific procedures on shifting into and out of Neutral (N). Transfer Case Position Indicator Lights Transfer case position indicator lights are located on the instrument cluster. If there are no indicator lights on or flashing the transfer case position is All-Wheel Drive (AWD) and indicate the current and desired transfer case selection (4HI ⇔ 4LOCK).
STARTING AND OPERATING 255 When operating your vehicle in 4LO, the engine speed is approximately three times that of the AWD or 4LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 40 km/h (25 mph). Proper operation of four-wheel-drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case.
STARTING AND OPERATING 4LOCK Four-Wheel-Drive LOCK - Locks the transfer case interaxle differential. Forces front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Shifting Procedure - NV 244 Generation II Transfer Case 4LO Four-Wheel-Drive Low Range - Low speed 4 wheel drive. Locks the transfer case inter-axle differential. Forces the front and rear wheels to rotate at the same speed.
STARTING AND OPERATING 257 wheels to complete the shift. There may be a delay up to 13 seconds for the shift to complete after the wheels have stopped spinning. NOTE: Delayed shifting out of the 4LOCK position may be experienced due to uneven tire wear, low tire pressure, or excessive loading. NOTE: When shifting into or out of 4LO some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants.
STARTING AND OPERATING NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The indicator light will flash and the current transfer case position will be maintained. To retry the selection, turn the control knob back to the current position, wait five (5) seconds, and retry the shift. PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel.
STARTING AND OPERATING 259 NOTE: The instrument cluster brake warning light indicates only that the parking brake is applied. You must be sure the parking brake is fully applied before leaving the vehicle. When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should be applied whenever the driver is not in the vehicle.
STARTING AND OPERATING BRAKE SYSTEM In the event power assist is lost for any reason, (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be significantly increased over that required with the power system operating. surfaces. All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate signals for the computer.
STARTING AND OPERATING 261 At the instant one of the wheels is about to lock up, a slight pulsation can be felt in the brake pedal, indicating that the ABS is in the regulating mode. Keep firm and steady pressure on the brake pedal while experiencing the pulsation. Continuous, steady brake pedal pressure results in optimal braking power while maintaining the ability to steer the vehicle. In the case of an emergency brake maneuver, keep continuous full pressure on the brake pedal.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 263 If for some reason, the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
STARTING AND OPERATING ROCKING THE VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. TIRE SAFETY INFORMATION Tire Markings The least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
STARTING AND OPERATING 265 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 267 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING 269 Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 271 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. 6.
STARTING AND OPERATING
STARTING AND OPERATING 273 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING 275 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING loading may be required for high speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
STARTING AND OPERATING 277 Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling.
STARTING AND OPERATING 279 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. • Driving style Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 281 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than Replacing original tires with tires of a different size may result in false speedometer and odometer readings. that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION – IF EQUIPPED A light load vehicle condition is defined as two passengers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo. Cold tire inflation pressures for a lightly loaded vehicle will be found on the face of the driver’s door.
STARTING AND OPERATING 283 These cautions apply to all chain traction devices, including link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Durango trucks. NOTE: The use of class “S” chains is permitted on Durangos with P245/70R17 tires. CAUTION! Do not use tire chains on 4x4 Durango trucks equipped with tires other than P245/70R17 tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle.
STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING 285 FUEL REQUIREMENTS All engines (except 5.7L engines) are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an oc3.7L/4.7L tane rating of 87. The routine use of preEngines mium gasoline is not recommended. Under normal conditions the use of premium fuel will not provide a benefit over high quality regular gasolines and in some circumstances may result in poorer performance. The 5.
STARTING AND OPERATING and durability for your vehicle. We recommend the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. We strongly support the use of reformulated gasolines.
STARTING AND OPERATING 287 MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT reduce spark plug life and reduce emission system performance. We recommend that gasolines free of MMT be used in your vehicle.
STARTING AND OPERATING NOTE: Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. Make sure that the gas cap is tightened each time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door.
STARTING AND OPERATING 289 CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using • WARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank.
STARTING AND OPERATING NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon mon- oxide, a colorless and odorless gas which can kill.
STARTING AND OPERATING 291 CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, you must keep the engine maintained to assure proper operation and prevent possible damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
STARTING AND OPERATING vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Service, including a tune-up to manufacturer’s specifications should be obtained immediately. To minimize the possibility of catalyst damage: VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration Regulations, your vehicle has a certification label affixed to the driver’s side door.
STARTING AND OPERATING 293 Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the Month, Day, and Hour of manufacture. The bar code that appears on the bottom of the label is your Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options, and cargo.
STARTING AND OPERATING Inflation Pressure (Cold) This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR. Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.
STARTING AND OPERATING 295 WARNING! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. A loaded vehicle is shown in the following example. Note that neither GVWR nor GAWR capabilities are exceeded. Overloading can cause potential safety hazards and shorten service life.
STARTING AND OPERATING TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
STARTING AND OPERATING 297 Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing hitch includes a receiver attached to the tow vehicle, plus a removable hitch head and spring bar assembly that fits into the receiver opening and hook up brackets that connect the spring bars to the trailer frame. Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin.
STARTING AND OPERATING 299 Trailer Hitch Classification Class Max. GTW (Gross Trailer Wt.) Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium 3,500 lbs (1587 kg) Duty Class III - Heavy Duty 5,000 lbs (2268 kg) Class IV - Extra 10,000 lbs (4540 kg) Heavy Duty Fifth Wheel/ Greater than 10,000 lbs (4540 Gooseneck kg) All trailer hitches should be professionally installed on your vehicle.
STARTING AND OPERATING Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
STARTING AND OPERATING 301 CAUTION! WARNING! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel.
STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. With a manual transmission, shift the transmission into reverse.
STARTING AND OPERATING 303 − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to the Tires–General Information section of this manual on Tread Wear Indicators for the proper inspection procedure. − When replacing tires refer to the Tires–General Information section of this manual on Replacement Tires for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits.
STARTING AND OPERATING WARNING! NOTE: Do not cut or splice wiring into the vehicles wiring harness. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you.
STARTING AND OPERATING 305 If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “TOW HAUL” or “OD/OFF” range should be selected. 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
STARTING AND OPERATING NOTE: Check the automatic transmission fluid level before towing. Towing Tips — Tow/Haul (If Equipped) To reduce potential for automatic transmission overheating, turn the “TOW HAUL OD/OFF” feature ON when driving in hilly areas or shift the transmission to Drive position 2 on more severe grades.
STARTING AND OPERATING 307 Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface. SNOWPLOW WARNING! Snowplows, winches, and other aftermarket equipment should not be added to the front end or your vehicle.
STARTING AND OPERATING WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational Towing 2WD Models Recreational towing of 2WD models is not allowable. Towing the vehicle with the transmission in Neutral can cause severe transmission damage.
STARTING AND OPERATING 309 WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move despite the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING 2. Shut engine OFF. 3. Turn the ignition key to the ON position without starting the engine. 11. Repeat steps 9 and 10 with the transmission in Drive (D). 12. Turn ignition key to the unlocked OFF position. 4. Depress brake pedal. 13. Shift automatic transmission into Park (P). 5. Shift automatic transmission to Neutral (N). 14. Attach vehicle to tow vehicle with tow bar. 6.
STARTING AND OPERATING 311 NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not ON, the shift will not take place and no position indicator lights will be on or flashing. 3. Turn the ignition key to the ON position without starting the engine. 4. Depress brake pedal. 5. Shift automatic transmission to Neutral (N).
STARTING AND OPERATING NOTE: Items 1 through 5 are requirements that must be met prior to depressing the Neutral (N) selection button, and must continue to be met until 1 second elapses and the shift has been completed. If any of these requirements are not met prior to depressing the Neutral (N) button or are no longer met during the 1 second time, then all of the position indicator lights will flash continuously until all requirements are met or until the Neutral (N) button is released.
STARTING AND OPERATING 313 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the car in front to avoid a collision in a sudden stop. EQUIPMENT IDENTIFICATION PLATE The equipment Identification Plate is located on the hood inner surface.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 316 䡵 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 325 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 316 䡵 Emergency Tow Hooks — If Equipped . . . . . . . . 327 䡵 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 317 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . . 328 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES 317 WARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling.
WHAT TO DO IN EMERGENCIES WARNING! The jack is designed as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
WHAT TO DO IN EMERGENCIES 319 Removing The Spare Tire The spare tire on the Dodge Durango is located underneath the vehicle in the rear. 6 2. Engage the jack wrench extension to the spare tire winch through the hole in the floor. Remove the spare tire before attempting to jack the truck. 1. Remove the rubber plug from the floor in the cargo area. 3. Turn the wrench counterclockwise to lower the spare tire. Continue to turn the wrench until the spare tire can be pulled out from under the vehicle.
WHAT TO DO IN EMERGENCIES It is recommended that you stow the flat or spare to avoid tangling the loose cable. Tire Changing Procedure WARNING! CAUTION! The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
WHAT TO DO IN EMERGENCIES 321 • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in PARK (automatic transmission). On Four Wheel Drive vehicles, shift the transfer case to the “4L” position.
WHAT TO DO IN EMERGENCIES (prior to inboard transition. Operate the jack using the jack drive tube and the wheel wrench - the tube extension, may be used but is not required. the tire as posssible with the drive tubes extending to the rear. Connect the jack tube extension and wheel wrench. Rear Left Jacking Location Front Jacking Location When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
WHAT TO DO IN EMERGENCIES 323 WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wheel off. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack, tools and the extra tire and wheel in the places provided. Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
WHAT TO DO IN EMERGENCIES 325 To Stow The Flat Or Spare Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle. Rotate the winch mechanism until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip or click 2 times.
WHAT TO DO IN EMERGENCIES Check the Battery Test Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery. If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1. Wear eye protection and remove all metal jewelry such as watch bands or bracelets which might make an unintended electrical contact. 2. Park the booster vehicle within cable reach but without letting the vehicles touch.
WHAT TO DO IN EMERGENCIES 327 WARNING! WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting jump start.
WHAT TO DO IN EMERGENCIES WARNING! CAUTION! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury.
WHAT TO DO IN EMERGENCIES 329 Four-Wheel Drive Vehicles The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. If the vehicle is to be towed more than 15 miles (25 km ) or faster than 30 mph, it must be towed on a flatbed, or with the rear wheels raised and the front wheels on the ground, or with the front end raised and the rear wheels on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment 3.7L V6 . . . . . . . . . . . . . . 334 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . . 340 䡵 Engine Compartment 4.7L V-8 . . . . . . . . . . . . . . 335 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 340 䡵 Engine Compartment 5.7L HEMI V-8 . . . . . . . . . 336 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 344 䡵 Onboard Diagnostic System — OBD II . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Catalytic Converter . . . . . . . . . . . . . . . . . . . . 347 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 362 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 348 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . 364 ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 349 ▫ Axles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 ▫ Power Steering — Fluid Check . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 333 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 377 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 384 ▫ Headlights/Parking/Turn Signal . . . . . . . . . . 377 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 385 ▫ Rear Side Marker, Tail Lights, Turn Signals And Backup Lights — Replacement . . . . . . . . 378 䡵 Fluids, Lubricants And Genuine Parts . . . . . . . . 386 ▫ License Lights . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 3.
MAINTAINING YOUR VEHICLE 335 ENGINE COMPARTMENT 4.
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 5.
MAINTAINING YOUR VEHICLE 337 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 339 3. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 4. Approximately 15 seconds later, one of two things will happen: a. The MIL light will blink for approximately 5 seconds and then remain on until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE 341 1. Position the vehicle on a level surface. 2. Turn Off the engine and allow approximately 5 minutes for the oil to settle to the bottom of the crankcase. 3. Remove the engine oil level indicator (dipstick). 4. Wipe the engine oil level indicator (dipstick) clean. 5. Install the engine oil level indicator (dipstick) and make sure it is seated in the tube. 6.
MAINTAINING YOUR VEHICLE Frequency Of Oil Change Road conditions and your style of driving affect the interval at which your oil should be changed. Check the following to determine if ANY apply to you: • Day or night temperatures are below 32°F (0°C). • Stop and Go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C).
MAINTAINING YOUR VEHICLE 343 This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specifi- periodically. Make sure that these units are always clean. This will tend to reduce to a minimum the amount of abrasive material that may enter the engine.
MAINTAINING YOUR VEHICLE For information on engine oil filler cap location, see the Engine Compartment illustration in this section. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used. Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that meet the American Petroleum Institute (API) and SAE viscosity standard.
MAINTAINING YOUR VEHICLE 345 Drive Belts — Check Condition and Tensioner Belt tension is controlled by means of an automatic tensioner. No belt tension adjustments are required. However, belt and belt tensioner condition should be inspected at the specified intervals, and replaced if required. See your authorized dealer for service. At the mileage indicated in the maintenance schedule, all belts and tensioner should be checked for condition. Improper belt tension can cause belt slippage and failure.
MAINTAINING YOUR VEHICLE Ignition Cables Replace the ignition cables (5.7L engines only) at the mileage interval shown in the maintenance charts. Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”.
MAINTAINING YOUR VEHICLE 347 Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE 349 WARNING! CAUTION! Battery posts, terminals, and related accessories contain lead and lead compounds. Always wash hands after handling the battery. It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE 351 WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE attention should also be given to hood latching components to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant directly into the lock cylinder.
MAINTAINING YOUR VEHICLE 353 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, follow the preceding safety tips. Cooling System Inspection Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
MAINTAINING YOUR VEHICLE 355 WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood don’t open the hood until the radiator has had time to cool. If you open the hood and see steam or hot coolant escaping from the radiator, don’t touch anything. Get away quickly. Never try to open a pressure cap when the radiator is hot.
MAINTAINING YOUR VEHICLE Recommended Engine Coolant This vehicle has been factory filled with an Ethylene Glycol based engine coolant with long life corrosion inhibitors (called HOAT, for Hybrid Organic Additive Technology). Follow the “Maintenance Schedule” for the recommended coolant change intervals. Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. CAUTION! • Mixing of coolants other than specified engine coolant, may result in engine damage, and decrease corrosion protection.
MAINTAINING YOUR VEHICLE 357 Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOAT ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution.
MAINTAINING YOUR VEHICLE WARNING! The warning words “DO NOT OPEN HOT” on the coolant pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap when the system is hot or under pressure. The radiator normally remains completely full, so there is no need to remove the pressure cap except checking coolant freeze point or replacement with new antifreeze coolant.
MAINTAINING YOUR VEHICLE 359 D. Maintain coolant concentration at 50% HOAT ethylene glycol engine coolant (minimum) and distilled water for proper corrosion protection of your engine. E. Make sure that the radiator and coolant bottle overflow hoses are not kinked or obstructed. F. Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean also. G. The thermostat should not be changed for summer or winter operation.
MAINTAINING YOUR VEHICLE You are urged to use only the manufacturer’s specified hoses and clamps, or their equivalent in material and specification, in any fuel system servicing. It is mandatory to replace all clamps that have been loosened or removed during service. Care should be taken in installing new clamps to insure they are properly torqued.
MAINTAINING YOUR VEHICLE 361 WARNING! CAUTION! Use of brake fluid that may have a lower initial boiling point, or is unidentified, as to specifications may result in sudden brake failure during hard prolonged braking. You could have an accident. Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching on fire.
MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Automatic Transmission Fluid Level Check Check the fluid level while the transmission is at normal operating temperature 180°F (82°C). This occurs after at least 15 miles (24 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips.
MAINTAINING YOUR VEHICLE 363 a minimum of two (2) minutes for the oil to fully drain into the transmission before rechecking the fluid level. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD” (lower) holes on the dipstick with the fluid at approximately 70°F ( 21°C) (room temperature).
MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufacturers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes. Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. Special Additives The manufacturer strongly recommends against the addition of any additives to the transmission.
MAINTAINING YOUR VEHICLE 365 Axles Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. Front Axle Front Axle fluid level should be 3/4” (20 mm) below the bottom of the fill hole. The manufacturer does not recommend regularly scheduled oil changes for axles in vehicles whose operation is classified as normal truck service.
MAINTAINING YOUR VEHICLE There are two groups identified, those for wheel bearings (Letter “G”) and those for chassis (Letter “L”) lubrication. Performance categories within these groups result in dual letter designations for each group. The letter designations shown in the example are the highest quality level available and when combined as shown can be used for chassis lubrication.
MAINTAINING YOUR VEHICLE 367 The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly.
MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible.
MAINTAINING YOUR VEHICLE 369 Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar威 Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. POWER DISTRIBUTION CENTER (FUSE/RELAY) Your vehicle is equipped with two electrical power distribution centers located next to each other in the left side of the engine compartment. 2. Dry with a soft tissue.
MAINTAINING YOUR VEHICLE 371 FUSE BLOCK CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it suggests a problem in the circuit that must be corrected. NOTE: If you are leaving your vehicle dormant for longer than 21 days you may want to take steps to protect your battery.
MAINTAINING YOUR VEHICLE Fuse Block Cavity Mini Fuse/Color F1 15 Amp Blue F2 10 Amp Red F3 10 Amp Red F4 10 Amp Red F5 (2) 10 Amp Red F6 F7 10 Amp Red 25 Amp Natural F8 10 Amp Red F9 F10 10 Amp Red 10 Amp Red Description Instrument Cluster Battery Feed Occupant Classification Module (OCM) Battery Feed Ignition Run/Start for Controller (NGC), Integrated Power Module (IPM), AC Relay and Fuel Pump Relay Door Node and NonMemory Power Mirror Switch Battery Feed Airbags (2 Fuses in Yellow
MAINTAINING YOUR VEHICLE 373 Cavity F11 F12 Mini Fuse/Color 10 Amp Red 20 Amp Yellow F13 10 Amp Red F14 10 Amp Red F15 15 Amp Blue F16 20 Amp Yellow F17 F18 20 Amp Yellow 10 Amp Red F19 15 Amp Blue F20 25 Amp Natural Description Heated Mirrors Cluster Battery Feed Ignition Run HVAC Module/Heated Rear Glass (EBL) Relay ABS Module Ignition Run Battery Feed Blue Tooth, Compass/Trip Computer (CMTC), Sentry Key Diagnostics Reconfigurable Power Outlets Cigar Lighter Ignition Spare Fuse Heating &
MAINTAINING YOUR VEHICLE Cavity 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Cartridge Fuse / Relay 40 Amp Green Mini Fuse 30 Amp Pink 40 Amp Green 50 Amp Red 10 Amp Spare 20 Amp 20 Amp Spare 20 Amp 20 Amp 20 Amp 15 Amp 15 Amp Spare Red Description JB Feed / EBL / T Case Brake JB Feed RR ABS Pump JB Feed Crank Yellow Fuel Pump Yellow NGC Yellow Yellow Yellow Blue Blue ABS Batt NGC Batt Trailer Tow A/C Clutch JB Feed Stop Cavity Cartridge Fuse / Relay 27 28 29 30 31 32 33 34 35 Relay Relay Sp
MAINTAINING YOUR VEHICLE 375 Underhood Fuses (Integrated Power Module) Cartridge Cavity Fuse / Relay 1 Relay 2 Relay 3 4 Relay Relay 5 Relay 6 Relay 7 Relay Mini Fuse 8 9 10 Amp Red 10 Amp Red 10 10 Amp Red Description Wiper On/Off Rly Wiper Hi/Lo Rly Horn Rly Rear Wiper Rly Lt T-Tow Stop/Turn Rly Rt T-Tow Stop/Turn Rly Park Lamps Rly Lt Park Lamps T-Tow Park Lamps Rt Park Lamps Cavity 11 Cartridge Fuse / Relay Relay Mini Fuse 12 13 14 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 16 17
MAINTAINING YOUR VEHICLE 24 Cartridge Fuse / Relay Relay 25 Relay 26 Relay Cavity 27 28 29 30 Mini Fuse 30 Amp Green 30 Amp Green Description Rad Fan Lo Rly Ft Fog Lamps Rly Adjustable Pedal Rly IOD #1 IOD #2 Spare Spare REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb No. Dome Light . . . . . . . . . . . . . . . . . . . . . . . . WL212–2 Liftgate Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 567 Overhead Console Lights . . . . . . . . . . . . . PLW214–2A Reading Light . . .
MAINTAINING YOUR VEHICLE 377 BULB REPLACEMENT Headlights/Parking/Turn Signal 2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by removing the fender panel access door which is located in the wheel liner. 3. Grasp the headlight and pull firmly to disengage the headlight from the fender panel. 4. While firmly holding the headlight in your hands disconnect all connectors by following the procedure described in step number 5 below. 1.
MAINTAINING YOUR VEHICLE 6. Twist and remove socket from lamp. 7. Remove bulb from socket and replace. NOTE: These are Halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat build-up which reduces bulb life. Rear Side Marker, Tail Lights, Turn Signals And Backup Lights — Replacement 1. Remove the two push-pins from the tail light housing.
MAINTAINING YOUR VEHICLE 379 2. Rotate the light to the outboard side of the vehicle and remove.
MAINTAINING YOUR VEHICLE 3. Unlock and remove electrical connector. 4. Remove the three screws holding the bulb strip to the back of the tail lamp.
MAINTAINING YOUR VEHICLE 381 5. Remove the bulb strip from the tail light lens. 6. Remove bulbs from bulb strip by pulling the bulb straight out.
MAINTAINING YOUR VEHICLE License Lights 1. Remove the two screws securing the lens to the liftgate.
MAINTAINING YOUR VEHICLE 383 2. Rotate the socket 1/4 turn counterclockwise. Center High-Mounted Stoplight 1. Remove two screws securing stoplight housing assembly to the liftgate. 3. Pull bulb from socket.
MAINTAINING YOUR VEHICLE 2. Turn socket 1/4 counterclockwise and free from housing. Fog Lights 1. Rotate bulb and connector 1/4 turn counterclockwise. 2. Pull bulb off of connector. NOTE: For foglights ensure that the takeout pushfasteners are relocated back in their positions; one in the foglight molding and the other in the hydroform. 3. Pull bulb straight from socket to remove.
MAINTAINING YOUR VEHICLE 385 FLUIDS AND CAPACITIES U.S. Metric 27 Gal. 27 Gal 102L 102L 5 Qt. 6 Qt. 7 Qt. 4.7L 5.7L 6.6L 13.5 Qt. 14.5 Qt. 13.1 Qt. 14.2 Qt. NA 16.6 Qt. 12.9L 13.8L 12.5L 13.5L NA 15.8L Fuel 3.7L/4.7L, 87 Octane 5.7L, 89 Octane Engine Oil (with filter) 3.7L, SAE 5W-30, API Certified 4.7L, SAE 5W-30, API Certified 5.7L, SAE 5W-20, API Certified Cooling System (includes 2.1 Qts./2L for coolant bottle 3.7L without Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 3.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant 3.7/4.7L Engine Oil 5.7L Engine Oil Engine Oil Filter Spark Plugs Fuel Selection 3.7L/4.7L Fuel Selection 5.7L Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use SAE 5W-30, API Certified, meeting material standard MS-6395 or equivalent.
MAINTAINING YOUR VEHICLE 387 Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar威 ATF+4, Automatic Transmission Fluid. Mopar威 ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant or equivalent. SAE 75W-140 Synthetic Gear Lubricant or equivalent. Mopar威 DOT 3 and SAE J1703 should be used or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 390 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 394 䡵 Emissions Testing . . . . . . . . . . . . . . . . . . . . . . . 390 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 405 C 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 391 䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 390 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES 391 M MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km).
M A I N T E N A N C E S C H E D U L E S 8 392 MAINTENANCE SCHEDULES Use the schedule that best describes your driving conditions. Where time and mileage are listed, follow the interval that occurs first. At Each Stop for Fuel NOTE: Under no circumstances should oil change intervals exceed 6000 miles (10 000 km) or 6 months whichever comes first. • Check the engine oil level about 5 minutes after a fully warmed engine is shut off.
MAINTENANCE SCHEDULES 393 M A I N T Change the engine oil filter. E N Inspect the exhaust system. A N Inspect the brake hoses. C Inspect the CV joints (if equipped) and front suspen- E Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed.
M A I N T E N A N C E S C H E D U L E S 8 394 SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F (32° C). • Trailer towing.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect engine air cleaner filter, replace if necessary.
M 396 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
M 398 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect and replace ignition cables if necessary (5.7L only).
SCHEDULE “B” Miles (Kilometers) Inspect auto tension drive belt and replace if required. Drain and refill automatic transmission fluid, change filter (3.7L). This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing. Drain and refill automatic transmission fluid and change main sump filter (4.7L/5.7L only). This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing. Inspect transfer case fluid (4X4).
M 400 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Inspect auto tension drive belt and replace if required.
SCHEDULE “B” Miles (Kilometers ) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
M 402 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 months A whichever comes first. N C Rotate tires. E Check spare tire for proper pressure and correct stowage. S C H E D U L E S 8 Flush and replace engine coolant, if not replaced at 60 months. Change rear axle fluid. Change front axle fluid (4X4).
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect and replace ignition cables if necessary (5.7L only). Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
M 404 SCHEDULE “B” A I N Miles T (Kilometers) E N Drain and refill transfer case fluid (4X4). A Drain and refill automatic transmission fluid, N C change filter (3.7L). This applies only if your E vehicle is used for police, taxi, fleet, or freS C H E D U L E S 8 105,000 (175 000) quent trailer towing. Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped. (4.7L/5.7L only).
SCHEDULE “A” 405 M Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace as necessary. Replace spark plugs.
M 406 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Check spare tire for proper pressure and corS C H E D U L E S 8 rect stowage. Check transfer case fluid level (4X4). Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (170 000 km). Inspect brake linings.
SCHEDULE “A” Miles (Kilometers) [Months] Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary. * Inspect and replace ignition cables if necessary (5.7L only). Inspect auto tension drive belt and replace if required.
M 408 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Check spare tire for proper pressure and correct S C H E D U L E S 8 stowage. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Drain and refill tranfer case fluid (4X4). Flush and replace engine coolant, if not replaced at 60 months. Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (170 000 km). Inspect brake linings. Inspect engine air cleaner filter, replace as necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.
M A I N T E N A N C E S C H E D U L E S 8 410 SCHEDULE “A” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: WARNING! • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Power Distribution Center (PDC). The I.O.D.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 ▫ Prepare For The Appointment . . . . . . . . . . . . 412 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 412 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 412 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 412 䡵 Warranty Information (U.S. Vehicles Only) . . . . . 415 䡵 Mopar威 Parts . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 413 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE 415 WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE 417 Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . 186,260 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . 287,316 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 346 Air Conditioner Maintenance . . . . . . . . . . . . 223,349 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 222 Air Conditioning, Operating Tips . . . . . . . . . . . . 234 Air Conditioning, Rear Zone . . . . . . . . . . . . . . . . 226 Air Conditioning Refrigerant . . . . . . . . . . . . .
INDEX 421 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 325 Gas Caution . . . . . . . . . . . . . . . . . . . . . . . . . . 325 Keyless Transmitter Replacement (RKE) . . . . . . . 26 Saving Feature (Protection) . . . . . . . . . . . . . . . 132 Belts, Drive . . . . . . . . . . .
INDEX Cargo Organizer . . . . . . . . . . . . . . . . . . . . . . . 176 Cargo Organizer . . . . . . . . . . . . . . . . . . . . . . . . 176 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 292 Catalytic Converter . . . . . . . . . . . . . . . . . . . . 291,347 CD (Compact Disc) Player . . . . . . . . . . . . . . . 193,200 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 88,222 Center High Mounted Stop Light . . . . . . . . . . . . 383 Certification Label . . . . . . . . . . .
INDEX 423 Points to Remember . . . . . . . . Radiator Cap . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Temperature Gauge . . . . . . . . . Cruise Control (Speed Control) . . Cup Holder . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . 358 . . . . . . . . . . . . 357 . . . . . . 356,385,386 . . . . . . . . . . . . 183 . . . . . . . . . . . . 142 . . . . . . . . . . . . 173 . . . . . . . . . . . . 412 Data Recorder, Event . . . . . . . . . . . . .
INDEX Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 357 Tow Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328 Emission Control System Maintenance . . . . . . . . . 390 Emission Related Components . . . . . . . . . . . . . . 359 Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 346 Block Heater . . . . . . . . . . .
INDEX 425 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 344 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 316 Turn Signal . . . . . . . . . . . . . . . . . . . . . 136,183,378 Flat Tire Stowage . . . . . . . . . . . . . . . . . . . . . 319,325 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 243 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . 360,387 Fluid Capacities . . .
INDEX Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 286 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . . 183 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 185 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 Glass Cleaning . . . .
INDEX 427 Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 14 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 64,65 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . 282 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 84 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . 183 Instrument Panel and Controls . . . . . . . . . . . . . .
INDEX Bulb Replacement . . . . . . . . . . . . . . . . . . . 376,377 Center Mounted Stop . . . . . . . . . . . . . . . . . . . 383 Courtesy/Reading . . . . . . . . . . . . . . . . . . . . . 155 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 134 Door Ajar . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 Electronic Stability Program (ESP) Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 429 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Lubricating Oil . . . . . . . . . . . . . . . . . . . . . . . . . 365 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 351 Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . . . 174 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . 113 Maintenance Free Battery . . . . . . . . . . .
INDEX Change Interval . . . . . . . . . . . . . . . . . . . . . . . 342 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344,386 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . 344 Identification Logo . . . . . . . . . . . . . . . . . . . . . 343 Materials Added to . . . . . . . . . . . . . . . . . . . . . 344 Recommendation . . . . .
INDEX 431 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 387 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 47 Preparation for Jacking . . . . . . . . . . . . . . . . . . . . 321 Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Programmable Electronic Features . . . . . . . . .
INDEX Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 339 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 280 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 415 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . 64,69 Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . 36 Rocking Vehicle When Stuck . . . . . . . . . . . . . . . . 264 Roof Type Carrier . . . . . . . . . . . . . . . . . . . . . . . 174 Rotation, Tires . . . . . . .
INDEX 433 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 12 Service and Maintenance . . . . . . . . . . . . . 340,390,391 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 412 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 414 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 416 Setting the Clock . . . . . . . . . . . . . . . . 192,195,202,215 Shifting Automatic Transmission . . . . . . . . . . . . . . . . . 245 Transfer Case . . . . . . . . .
INDEX Stuck, Freeing . . . . . . . . . . . . . . . . . . . . . . . . . . 264 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Supplemental Tire Pressure Information . . . . . . . . 282 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . 344 System, Remote Starting . . . . . . . . . . . . . . . . . . . . 28 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Taillights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 435 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 279 Wheel Mounting . . . . . . . . . . . . . . . . . . . . . . . 320 Wheel Nut Torque . . . . . . . . . . . . . . . . . . . . . 323 Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 299 Torque Converter Clutch . . . . . . . . . . . . . . . . . . 249 Tow Hooks, Emergency . . . . . . . . . . . . .
INDEX Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 24 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 279 Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Trip Odometer Reset Button . . . . . . . . . . . . . . . . 191 Turn Signals . . . . . . . . . . . . . . . . . . . . . . 136,183,378 Underhood Fuses . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 437 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 352 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 137 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 352 Wiper, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . 137 Wrecker Towing . . . . . . . . . . . . . . . . . . . . . . . . .
NOTES
NOTES
NOTES
