SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 3 4 INSTRUMENT PANEL AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I nf or mat i onPr ov i dedby :
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 5 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . . 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . . 9 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . . 9 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .17 ▫ Sentry Key — If Equipped . . . . . . . . . . . . . . . . 9 䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . .19 䡵 Ignition And Steering Lock . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Security Alarm System — If Equipped . . . . . . . . .24 ▫ Enhanced Driver Seat Belt Reminder System (BeltAlert) . . . . . . . . . . . . . . . . . . . . . . . . . . .36 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .25 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .37 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .25 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .37 䡵 Liftgate . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number. NOTE: Integrated keys (key and key fob combined) must be cut by the dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE on the remaining transmitters will work. If the vehicle is moving 5 mph or more, then all the transmitter buttons are disabled for all keys. NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IGNITION AND STEERING LOCK In the LOCK position, the steering and ignition systems are locked to provide anti-theft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle, if the steering wheel is locked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: The steering wheel will lock when the key is removed, and the steering wheel is turned around 115 degrees clockwise or 65 degrees counterclockwise from the center position. The interior lights will remain on for 30 seconds after the last door is closed, or until all doors are closed and either the ignition is turned to the ON position or a key fob LOCK button is pressed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 As a safety feature the doors will not lock when using the door lock switches during the following conditions: • The driver’s door is open while the key is in the ignition. Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Within 10 seconds, cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction. 6. A single chime will be heard to indicate the feature has been disabled. 7. To re-activate this feature, repeat the above steps. 8. If a chime is not heard, program mode was canceled before the feature could be disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 3. Insert the key into the ignition. 4. Within 10 seconds, cycle the key from the OFF position to the ON position four times ending in the ON position (do not start the engine). Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the childprotection door lock system. 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction. 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position. To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: The line of transmission must not be blocked with metal objects. REMOTE KEYLESS ENTRY To unlock the doors and liftgate: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Release both buttons at the same time. 4. Test the feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the keyfob. NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 6. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mode, the door locks and remote keyless entry systems will function normally. Panic mode will not disarm the security system on vehicles so equipped. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 9. A single chime will be heard. 10. Within four seconds of hearing the chime, press and release the UNLOCK button on the fob. 11. A single chime will be heard. 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the UNLOCK button on the key fob. 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Battery Replacement The recommended replacement battery is CR2032. 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 To Set the Alarm: The alarm will set when you use the power door locks or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the security light in the instrument cluster will flash rapidly to signal that the system is arming. The security light in the instrument panel cluster will flash rapidly for about 15 seconds to indicate that the alarm is being set.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNLOCK button or by inserting a programmed Sentry Key into the ignition and turning the key to the ON position. WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WINDOWS Power Windows 2 The control on the left front door has up-down switches that give you finger tip control of all four power windows. There is a single opening and closing switch on the passenger doors for passenger window control.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer. NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF. Auto Down The driver’s window switch has an Auto Down feature. Push the window switch past the first detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 window. If you will be carrying children too small for adult-size seat belts, your seat belts or the LATCH feature (refer to the Child Restraint section in this manual), can be used to hold infant and child restraint systems. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front and second row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Push in on the anchorage release button to release the anchorage, and then move it up or down to the position that serves you best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 When sitting in this seating location, ensure the seatback is fully engaged with the seatback latch by pushing rearward on the center seatback until you hear a click that signals latch engagement. Automatic Locking Mode To convert from the normal emergency locking mode to the automatic locking mode, grasp the shoulder belt portion and pull all of the webbing out of the retractor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 buckled. A chime will sound immediately (once the feature has toggled). If during this time the ignition switch is turned out of the ON position or the timer expires, programming mode will be cancelled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 4. If your vehicle has window bags, do not lean against the door or window, airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided in the ⬙If You Need Customer Assistance⬙ section later in this owner’s manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioners Air Bag System Components The airbag system consists of the following: • Occupant Classification System (OCS) for the Front Passenger Seat • Occupant Restraint Controller • Side Remote Acceleration Sensors (If Equipped) − Occupant Classification Module • Airbag Warning Light − Passenger Airbag Disable (PAD) Indicator Light • Driver Airbag − Weight Sensors • Passenger Airbag How the Airbag System Wo
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. During a moderate-to-severe rear impact the ORC may deploy the seat belt pretensioners alone.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. • The Passenger Airbag Disable (PAD) Indicator Light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag is turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 adult passenger is properly seated in the front passenger seat. In this case, the air bag is ready to be inflated if a collision requiring an airbag occurs. For almost all properly installed rear facing child restraints, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occupant is classified by the OCS.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 sensors, a fault will occur which turns on both the PAD Indicator Light and the Airbag Warning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time. the airbag. The passenger’s front airbag gas is vented through vent holes in the sides of the airbag. In this way the airbags do not interfere with your control of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Side Impact SRS Window Bags are designed to activate only in certain side collisions. When the ORC (with side impact option) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the outside edge of the headliner out of the way and covers the window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • Do not replace the seat cover with an aftermarket seat cover. WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Maintaining Your Airbag System WARNING! • • • • • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The light flickers or comes on and remains on while driving. NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control module may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 LATCH child restraint anchorage system. (See the LATCH - Child Seat Anchorage System section.) • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. If the seat belt has a automatic locking retractor, it will have a distinctive label.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and hooks for connection to the top tether anchorages have been available for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. only install the child restraints using the vehicle’s seat belts. Please refer to the next section for typical installation instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Second Row Right Side Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE anchorages. Next attach the lower hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material. Then attach the tether strap to the anchorage located on the back of the seat, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 it tight if necessary. If the seat belt has an automatic locking retractor, it will have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is all extracted from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Second Row Seat I nf or mat i onPr ov i dedby :
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Child Restraints in Third Row Seating (If Equipped) The third seating row is not capable of installing child restraints that require the use of a tether strap. There are no tether anchor provisions for the third seating row in your vehicle, the hooks in the rear floor are not designed to withstand the forces that may occur during a crash. Child Restraint Tether Anchor There are tether strap anchorages behind each seating position in the second row.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Follow the instructions below. See your dealer for help if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. SAFETY TIPS Exhaust System • It may be necessary to sit in a parked vehicle with the engine running for more than a short period. If so, adjust your climate control system to force outside air into the vehicle. Set the blower at high speed and the controls in any position except OFF or RECIRC.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Safety Checks You Should Make Outside The Vehicle: Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Fluid Leaks Check the area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected.
I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .74 ▫ Automatic Dimming Mirror — If Equipped . . . .74 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .75 ▫ Automatic Dimming Driver’s Exterior Mirror — If Equipped . . . . . . . . . . . . . . . . . . .78 䡵 Hands–Free Communication (UConnect™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 ▫ Third Seat 50/50 Split Seat — If Equipped . . . 111 ▫ Front Seat Manual Seat Adjustment . . . . . . . . 102 䡵 Driver Memory System — If Equipped . . . . . . . 114 ▫ Front Seats Manual Seat Recliners . . . . . . . . . . 103 ▫ Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory . . . . . . . 115 ▫ Manual Lumbar Support Adjustment — If Equipped . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 ▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . . 122 䡵 Traction Control Switch — If Equipped . . . . . . . 128 ▫ Automatic Headlights — If Equipped . . . . . . . 122 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . 129 ▫ Headlights, Parking Lights, Panel Lights . . . . . 123 䡵 Driver Adjustable Pedals — If Equipped . . . . . . 130 ▫ Illuminated Entry . . . . . . . . . . . . . . . . . . . . . 123 ▫ Adjustment . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Compass/Temperature Mini-Trip Computer . . . . 136 ▫ To Put Into a Calibration Mode . . . . . . . . . . . 140 ▫ US/M Button . . . . . . . . . . . . . . . . . . . . . . . . 136 ▫ Outside Temperature . . . . . . . . . . . . . . . . . . . 142 ▫ Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . 137 䡵 Garage Door Opener — If Equipped . . . . . . . . . 142 ▫ Global Reset . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . . 151 ▫ Floor Console Features . . . . . . . . . . . . . . . . . 153 ▫ Electrical Outlet Use With Engine Off (Battery Fed Configuration) . . . . . . . . . . . . . . 152 䡵 Factory Installed Roof Luggage Rack— If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 䡵 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . 153 䡵 Cargo Management System—If Equipped . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Exterior Mirrors Folding Feature — If Equipped Folding exterior mirrors are hinged and may be moved either forward or rearward to resist damage. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Driver’s Exterior Mirror — If Equipped This mirror will automatically adjust for annoying light glare from vehicles behind you. This feature is controlled by the inside mirror and can be turned off by pressing the button at the base of the inside mirror. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth ⬙Hands-Free Profile,⬙ version 0.96 or higher.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 each other without wires or a docking station, so UConnect works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect™ system. The UConnect™ system allows up to seven cellular phones to be linked to system. Only one linked (or paired) cellular phone can be used with the system at a time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can either be adjusted from the radio volume control knob, or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as ⬙CELL⬙ or caller ID on certain radios.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Help Command If you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙Help⬙ following the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help. type). To complete the pairing process, you will need to reference your cellular phone owner’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will be asked to say a four-digit pin number which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process. only one cellular phone can be in use, connected to your UConnect™ System. The priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 • For example, you can say ⬙234-567-8901.⬙ The phone number that you enter must be of valid length and combination. The UConnect™ limits the user from dialing invalid combination of numbers. For example, 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits. • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g.: ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. four associated phone numbers and designations.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Names⬙ to hear a list of the entries in the phonebook from which you choose. To select one of the entries from the list, press the ⬙Voice Recognition⬙ button while the UConnect™ system is playing the desired entry and say ⬙Delete.⬙ After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook List Names.⬙ • The UConnect™ system will play the names of all the phonebook entries.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the current call on hold and answer the incoming call. NOTE: The UConnect™ system compatible phones in market today do not support rejecting an incoming call when another call is in progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Conference Call When two calls are in progress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Redial Three-Way Calling To initiate three-way calling, press the ’Voice Recognition’ button while a call is in progress and make a second phone call as described in section ⬙Making a Second Call while Current Call in Progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect™ system will instruct the paired cellular phone to call the emergency number. This feature is only supported in the USA.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Paging To learn how to page, refer to section ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to section ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ system will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • Press the ’Voice Recognition’ button. Advanced Phone Connectivity • After the ⬙Ready⬙ prompt and the following beep, say ⬙Mute.⬙ Transfer Call to and from Cellular Phone The UConnect™ system allows on going calls to be transferred to your cellular phone to the UConnect™ system without terminating the call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone.⬙ • After the “Ready” prompt and the following beep, say “Setup Phone pairing”. • When prompted, say ⬙List Phones⬙. • The UConnect™ system will play the phone names of all paired cellular phones in order from the highest to the lowest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete.⬙ • The phone names (along with priority numbers) will be played. • When prompted say the priority number of the cellular phone (or “All” to delete all phones) you wish to delete. You can also press the ⬘Voice Recognition’ button anytime while the list is being played and say the priority number.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When navigating through an automated system, such as, voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙send.⬙ Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • Storing names in phonebook when vehicle is not in motion is recommended. • low-to-medium vehicle speed, • It is not recommended to store similar sounding names in the UConnect™ phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Bluetooth Communication Link Cellular phones have been found to occasionally loose connection to the UConnect™ system. When this happens, the connection can generally be re-established by switching the phone off/on. Your cell phone is recommended to remain in Bluetooth ⬙on⬙ mode. Reset In rare instances, it may be necessary to reset the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 3 I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones Pager Phone pairing Phonebook Return to main menu Select phone Set up I nf or mat i onPr ov i dedby : List phones Beeper Pairing Phone book Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Front Seat Manual Seat Adjustment The adjusting lever is at the front of the seat, near the floor. Lift the lever and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Front Seats Manual Seat Recliners The bucket seats are equipped with recliners. The reclining mechanism is operated by a lever located on the right side of the passenger’s seat and the left side of the driver’s seat. To recline, lean forward slightly before lifting the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints — All Seating Positions Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears. To lower the head restraint, depress the release button located at the base of the head restraint and push down on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Front Heated Seats — If Equipped 3 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the right side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjustment. The top switch controls the seatback recline adjustment. This feature heats the driver and front passenger seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE passenger to select from two different levels of supplemental electrical seat heating, or no seat heating to suit their individual comfort requirements. With the ignition switch in the RUN position, depressing the heated seat switch rocker to its momentary High or Low position provides power to the heated seat element and maintains the requested temperature setting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 To fold the 20% seatback, pull the strap forward to release the seatback. Fold the seatback down for use as an armrest or to carry cargo. When returning the seatback to the upright position, push the seatback rearward to latch the seatback. Pull the seatback forward to ensure that it is locked in the upright position. To Fold the 40% seatbacks fully raise the lever on the side of the seat to release the seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To Tumble the 40% seat, fully raise the lever on the side of the seat to release the floor latches and tumble the seat. The 20% seatback contains the center shoulder belt. A 20% seatback that is not fully latched in the upright position will not protect you properly. NOTE: The seatback must be fully folded into the down position to allow the lever to be raised enough to release the floor latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 To Fold and Tumble the 2nd row 40% seats from the 3rd row, fully raise the lever at the rear of the seat to fold the seatback. Continue raising the lever to release the floor latches to tumble the seat. NOTE: The head restraints must be lowered but do not have to be removed to fold and tumble the seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Achieve Maximum Cargo Capacity Pull the release handles and strap on the second row seats and fold flat. After folding the third row seat, unsnap the flipper panel on the third row seatback and flip it forward on the backs of the second row seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 NOTE: Before returning the second row 40% seats to their upright position, always snap the third row seat flipper panel(s) back to the third row seat first. Third Seat 50/50 Split Seat — If Equipped NOTE: The seat belt buckles are hinged to fold with the seat back. 3 WARNING! Do not sit in the third row seat unless the cushion and back are properly engaged. Proper engagement can be verified by pushing/pulling on the upright seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE on the floor behind the second row seats.The seat belt buckles are hinged and fold with the seatbacks. unsnap the flipper panels on the back of the third row seatbacks and flip the panels onto the backs of the second row seats. NOTE: Before returning the second row 40% seats the upright position, always reposition the flipper panel(s) and snap onto the third row seat first. NOTE: The seat belt buckles are hinged to fold with the seat backs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 WARNING! Do not sit in the third row seat unless the cushion and back are properly engaged. Proper engagement can be verified by pushing/pulling on the upright seatback. The seatback(s) will not move unless properly engaged. Do not sit in the 3rd row seat(s) with the second row seatback(s) folded or tumbled. In a collision, you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SYSTEM — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat position, driver’s outside mirror position, adjustable brake and accelerator pedals position, Automatic Temperature Control (ATC) temperature and radio station preset settings. Your Remote Keyless Entry transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory 5. Press and release the SET (S) button located on the driver’s door. NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store new settings. 6. Within 5 seconds, press and release memory button 1 or 2 on the driver’s door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memory Position Recall NOTE: • The driver’s seat belt must be unbuckled to recall memory positions. • The vehicle must be in Park to recall memory positions. • Not all motors may be moved at one time. Please refer to the 8-way power seat description. To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the Unlock button on the Remote Keyless Entry transmitter linked to memory position 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 3. Within 10 seconds, press and release the UNLOCK button on the Remote Keyless Entry transmitter. To disable another transmitter linked to either memory position, repeat steps 1-3 for each transmitter. NOTE: The capability to link Remote Keyless Entry transmitters to memory is enabled when delivered from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the seat is positioned rearward enough and no benefit from moving the seat any farther rearward. Reverse feature may be enabled (or later disabled) by a qualified DaimlerChrysler service representative. NOTE: The Easy Exit Easy Entry feature is not enabled when delivered from the factory. The Easy Exit Easy Entry feature may be enabled (or later disabled) by a qualified DaimlerChrysler service representative.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Then push the safety latch lever to the left. It is located between the grille and hood opening right of the center. NOTE: Ensure hood prop rod is fully seated into clip before closing hood to prevent damage to grille. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 all the way down to the OFF detent will cause all the interior lights to go out. This allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. Interior Lights The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the headlights remain on while the ignition is cycled off, the exterior lights will automatically turn off after 8 minutes. If the headlights are turned on and left on for 8 minutes while the ignition is off, the exterior lights will automatically turn off. NOTE: Battery Saver mode is cancelled if the ignition is ON. NOTE: While the engine is running, the system will deactivate the Fog Lights and Heated seats if a low battery system voltage is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Headlights, Parking Lights, Panel Lights When the headlight switch is rotated to the first position to the right, the parking lights, taillights, side marker lights, license plate light and instrument panel lights are all turned on. The headlights will turn ON when the switch is rotated to the second position. Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-on Reminder If the headlights, parking lights, or courtesy lights are left On, after the ignition is turned Off, a continuous fast chime will sound when the driver’s door is opened. Fog Lights — If Equipped position and pressing the fog light button. The fog lights will operate only when the parking lights are ON or when the vehicle headlights are ON low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective. Turn Signals If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate. You can signal a lane change by moving the lever partially up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam. Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during windshield washer use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed, for a period greater than 1 second, while in the OFF position, the wiper will wipe approximately three wipes, after the wash knob is released. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 To turn the system back ON, press the switch a second time until the traction control Indicator turns OFF. NOTE: • The traction control Indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF. • The Traction Control system will make buzzing or clicking sounds when in operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF EQUIPPED WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Adjustment CAUTION! 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, up to move the pedals toward the driver or down to move the pedals away from the driver. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator operation at speeds greater than (refer to the table below for the speed for your specific engine). The controls are mounted on the steering wheel. To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it. To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above (refer to the table below for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Functions Engage Speed Minimun RESUME Speed ACCEL Increase DECEL Decrease Dropout Speed 3.7L 35 mph (56 km/h) 30 mph (50 km/h) 2 mph (3km/h) 1 mph (2 km/h) 30 mph (50 km/h) To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped. These lights are also operated individually as reading lights by pressing the recessed area of the corresponding lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 RESET Button Global Reset If the RESET button and STEP button are pressed at the same time and held for 3 seconds (you will hear a confirmation beep) and the Global Reset feature will reset the distance to empty (using a default fuel economy value), fuel economy, trip odometer, and elapsed time displays. When this button is pressed you will hear a confirmation beep.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Step Button Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is connected or disconnected).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 fuel capacity, which corresponds to approximately 5% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers running out of fuel when operating at maximum load conditions in areas where there aren’t many gas stations. C/T Button 3 NOTE: The Distance To Empty will remain equal to zero, until the vehicle runs out of fuel or is refueled. Trip Odometer (ODO) This display shows the distance traveled since the last reset.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After completing one 360° turn, with the vehicle traveling less than 5 mph (8 km/h), in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally. Compass/Temperature Display WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 symbol is displayed complete one 360 degree turn in an area free from large metal objects or power lines. The CAL symbol will turn off and the compass will function normally. Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! For additional information on HomeLink威, call 1–800– 355–3515, or on the internet at www.homelink.com. I nf or mat i onPr ov i dedby : A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light (dots below House Symbol) in view. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with ⴖProgrammingⴖ steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙learn⬙ or ⬙smart⬙ button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 If you live in Canada or you are having difficulties programming a gate operator by using the ⬙Programming⬙ procedures (regardless of where you live), replace ⴖProgramming HomeLinkⴖ step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the ⬙cycling⬙ process to prevent possible overheating. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with ⬙Programming⬙ step 2 For questions or comments, contact HomeLink at: www.homelink.com or 1-800-355-3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 HomeLink威 is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console. Pressing the ⬙open⬙ end of the rocker switch once moves the panel to a comfort stop position short of full opening. Pressing and holding the switch causes the panel to continue moving rearward, up to the full-open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 FLOOR CONSOLE Floor Console Features The Floor Console between the driver’s and front passenger’s seat, has the following features: • Miscellaneous storage compartments • Flexible cup holder inserts • Portable phone storage bin • Portable phone cord routing between lid and base on forward edge • 12 Volt battery fed power outlet inside storage compartment • Side open armrest lid • Tissue holder & pen holder • Coin slots I nf or mat i onPr ov i dedby : 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Removable CD bin The coin slots are located under the instrument panel center stack. Cup Holders The Durango has 8 cupholders. Four are located in the center console, two are located in the second row armrest, and two are located in the right hand quarter panel for third row occupants. The four cupholders located in the center console may be removed for cleaning and are dishwasher safe.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 FACTORY INSTALLED ROOF LUGGAGE RACK— IF EQUIPPED The side rails between the stantions should be used to tie down cargo. Check the straps frequently to be sure that the load remains securely attached. NOTE: Crossbars are offered by Mopar威 accessories. External racks do not increase the total load carrying capacity of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack Cautions when carrying cargo on your roof rack.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 3 Cargo Organizer Closed Cargo Organizer Open To operate the cargo organizer dividers, insert finger into the hole, lift the dividers up and attach netting. To close the dividers, detach the netting at the top, pull on the release latch and push the dividers down to the closed position. To open the side cover, pull on the cover latch. To open the organizer base pull on the center latch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To remove the organizer from the vehicle, pull the right hand side of the organizer towards you so that the right pin slides out of the slot in the vehicle. Push the organizer to the right and lift out of the vehicle.
INSTRUMENT PANEL AND CONTROLS CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 162 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 163 䡵 Sales Code REF — AM/FM/CD (Single Disc) Radio With Optional Hands Free Phone Capability . . . . 173 ▫ Operating Instructions - Radio Mode . . . . . . . 174 䡵 Instrument Cluster Description . . . . . . . . . . . . . 164 ▫ Operation Instructions - CD Mode . . . . . . . . . 177 䡵 Radio Reception Information . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS ▫ Operation Instructions - (CD Mode For CD Audio Play) . . . . . . . . . . . . . . . . . . . . . . . . . 183 ▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . 193 ▫ Storing And Selecting Pre-Set Channels . . . . . . 193 ▫ Load/Eject Button (CD Mode For CD Audio Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 161 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 197 ▫ Level Of Automatic Control . . . . . . . . . . . . . . 203 ▫ Manual Control . . . . . . . . . . . . . . . . . . . . . . 197 ▫ Manual Control (ATC) . . . . . . . . . . . . . . . . . . 204 ▫ Air Conditioning Operation . . . . . . . . . . . . . . 198 ▫ Rear Zone Climate Control — If Equipped . . . 207 ▫ Front Blower Control . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS INSTRUMENTS AND CONTROLS I nf or mat i onPr ov i dedby :
INSTRUMENT PANEL AND CONTROLS 163 Instrument Cluster 4 I nf or mat i onPr ov i dedby :
INSTRUMENT PANEL AND CONTROLS INSTRUMENT CLUSTER DESCRIPTION CAUTION! 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. (See page 260 for more information.) 2. Temperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operating satisfactorily.
INSTRUMENT PANEL AND CONTROLS 165 left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. (See page 124 for more information.) 7. Fog Light Indicator — If Equipped This light shows when the fog lights are ON. 4. Low Fuel Warning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less. 8. Coolant Temperature Light This light warns of an overheated engine condition.
INSTRUMENT PANEL AND CONTROLS CAUTION! WARNING! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off. If the if the light remains on, turn the engine off immediately, and call for service. A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant.
INSTRUMENT PANEL AND CONTROLS 167 11. Liftgate Open The Gate Open light will illuminate when the liftgate is not properly closed. portion of the brake system is not functioning and that service is required. See your authorized dealer immediately. 12. Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set.
INSTRUMENT PANEL AND CONTROLS display will place a box around the selected transmission range (PRND21). If the PRNDL displays only the characters PRND21 (no boxes) have the system checked by an authorized dealer. 18. Odometer The odometer shows the total distance the vehicle has been driven. 17. Trip Odometer The trip odometer shows individual trip mileage. To toggle between the odometer and the trip odometer, press the Odometer/Trip Odometer Button.
INSTRUMENT PANEL AND CONTROLS 169 The Traction Control indicator will turn ON if: 20. Transmission Temperature Indicator This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. If this light comes on, stop the vehicle and run the engine at idle or faster, with the transmission in NEUTRAL until the light goes off. 21.
INSTRUMENT PANEL AND CONTROLS remain on until the condition has been corrected. If the parking brake is applied, the light will flash when the gear position is out of park for automatic transmissions. If brake failure is indicated, immediate repair is necessary. Operating the vehicle in this condition is dangerous! turned on and remain on, as a bulb check, until the engine is started.
INSTRUMENT PANEL AND CONTROLS 171 CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. 27. Airbag Indicator The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned ON.
INSTRUMENT PANEL AND CONTROLS 33. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display. Holding the button in resets the trip odometer reading. RADIO RECEPTION INFORMATION ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the frequency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the “ON” or “ACC” position.
INSTRUMENT PANEL AND CONTROLS 173 3. After the hours are adjusted, press the right side Tune / Audio control to set the minutes. 4. Adjust the minutes using the right side Tune / Audio control. SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL HANDS FREE PHONE CAPABILITY 5. To exit, press any button/knob or wait approximately 5 seconds.
INSTRUMENT PANEL AND CONTROLS Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
INSTRUMENT PANEL AND CONTROLS 175 NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
INSTRUMENT PANEL AND CONTROLS Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display.
INSTRUMENT PANEL AND CONTROLS 177 Preset Buttons 1 - 6 (Radio Mode) These buttons tune the Radio to the stations that you commit to push-button memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up.
INSTRUMENT PANEL AND CONTROLS SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear.
INSTRUMENT PANEL AND CONTROLS 179 Operating Instructions - Hands Free Phone — If Equipped Refer to the HANDS FREE PHONE (UConnect™) section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VIDEO CAPABILITIES Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
INSTRUMENT PANEL AND CONTROLS Mode Button (Radio Mode) Press the mode button repeatedly to select between the Radio, CD player, Hands Free Phone, Satellite, or Vehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down.
INSTRUMENT PANEL AND CONTROLS 181 RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display.
INSTRUMENT PANEL AND CONTROLS within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
INSTRUMENT PANEL AND CONTROLS 183 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
INSTRUMENT PANEL AND CONTROLS begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. SEEK Button (CD MODE For CD Audio Play) Press the right side of the SEEK button for the next selection on the CD.
INSTRUMENT PANEL AND CONTROLS 185 LOAD / EJECT - Eject Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJECT button to eject all discs in the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
INSTRUMENT PANEL AND CONTROLS RND/PTY Button (Random Play Button) (CD MODE For CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature.
INSTRUMENT PANEL AND CONTROLS 187 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files).
INSTRUMENT PANEL AND CONTROLS MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
INSTRUMENT PANEL AND CONTROLS 189 LOAD/EJECT Button (CD Mode For MP3 Play) LOAD / EJECT - Eject Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJECT button to eject all discs in the radio.
INSTRUMENT PANEL AND CONTROLS INFO Button (CD Mode For MP3 Play) Press and INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode. Press the INFO button once more to return to ⬙elapsed time⬙ priority mode.
INSTRUMENT PANEL AND CONTROLS 191 Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES威) (If Equipped) Refer to separate Video Entertainment System (VES威) Guide. SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio.
INSTRUMENT PANEL AND CONTROLS ESN/SID Access With REF Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the Eject or CD Eject (depending on the radio type) and Time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed. Press the SEEK UP button to display the next four digits. Continue to press the SEEK UP button until all twelve ESN/SID digits have been displayed.
INSTRUMENT PANEL AND CONTROLS 193 A CD may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Press and release the SCAN button (if equipped) to automatically change channels every 7 seconds.
INSTRUMENT PANEL AND CONTROLS one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Reception Quality Satellite reception may be interrupted due to one of the following reasons. PTY Button ⴖSEEKⴖ When the desired program is obtained, press the ⬙SEEK⬙ button within five seconds. The channel will change to the next channel that matches the program type selected.
INSTRUMENT PANEL AND CONTROLS 195 The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode. Radio Operation Pressing the top of the switch will SEEK up for the next listenable station and pressing the bottom of the switch will SEEK down for the next listenable station.
INSTRUMENT PANEL AND CONTROLS will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play. If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch changes CD’s on the 6–Disc in-dash CD changer radio. This button does not function for all other radios.
INSTRUMENT PANEL AND CONTROLS 197 RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
INSTRUMENT PANEL AND CONTROLS Air Conditioning Operation To turn the air conditioning On or Off perform the following steps: • Position the mode control button to the desired airflow setting. engine speed or power may be noticed when the compressor is on. This is a normal occurrence since the compressor will cycle on and off to maintain comfort and improve fuel economy. Front Blower Control The Front Blower controls the amount of air delivered to the passenger compartment.
INSTRUMENT PANEL AND CONTROLS 199 Front Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots and give an even blend of both modes.
INSTRUMENT PANEL AND CONTROLS air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Heat (Floor) Outside air flows primarily through the floor outlets located under the instrument panel. A small amount of air is directed through the defrost and side window demister outlets. Mix Outside air flows in equal proportions through the floor and defroster outlet.
INSTRUMENT PANEL AND CONTROLS 201 Rear Temperature Control — If Equipped Rotating this knob left to the “REAR CONTROL” position allows the passengers in the second and third row seats to control the blower speed and temperature by means of the rear control located in the rear of the center floor console as described under “Rear Zone Control.” Rotating this knob to the “OFF” position, turns off the rear climate controls.
INSTRUMENT PANEL AND CONTROLS mode on the front control will give you air from the outlets in the headliner in the rear. Floor mode in the front will give you floor in the rear. Rear Window Defrosting and Rear Window Washer/Wiper See the “Rear Window Features” section of this book. Automatic Temperature Control (ATC) — If Equipped The control can be turned on by pressing the POWER button. When the control is turned on, it will be in the last mode prior to being turned off.
INSTRUMENT PANEL AND CONTROLS 203 The ATC system uses an infrared sensor located in the overhead console to measure the temperature of the driver. Based on the sensor input, the system will automatically control comfort by varying the temperature, fan speed, and mode. This maintains a comfortable temperature, even under changing conditions. It is important that the infrared sensor is kept clean and that objects are not blocking the sensor.
INSTRUMENT PANEL AND CONTROLS Manual Control (ATC) You also may choose to customize your comfort by selecting the fan speed and mode manually. Pressing the fan speed button or any mode button places the system into manual operation. While in manual operation there are six fan speeds available and the choice of any mode. The airflow temperature is adjusted automatically to maintain the desired comfort level. You can adjust the temperature by pressing the + or – TEMP rocker switch.
INSTRUMENT PANEL AND CONTROLS 205 Manual control of Recirculation is possible only in Panel, Floor, and Bi-Level modes. It will not operate in Mix, or Defrost modes. The recirculation symbol will flash three times indicating recirculation is not available in these modes. NOTE: If the interior of the windows begin to fog, press the recirculate button to return to outside air. Some conditions will cause captured interior air to fog windows when in recirculate mode.
INSTRUMENT PANEL AND CONTROLS the A/C snowflake button has not been pressed. This dehumidifies the air to help dry the windshield. Rear Temperature Control (ATC) The “REAR FUNCTIONS” button cycles through the following modes: Rear Control from Front This allows the driver or passenger to control the rear blower speeds using the FAN +/– rocker switch and the rear temperature using the TEMP +/– rocker switch. While in this mode, pressing the POWER button will turn the rear system off.
INSTRUMENT PANEL AND CONTROLS 207 Rear Zone Climate Control — If Equipped 4 Headliner air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knobs on the outlets to one side will shut off the airflow. The rear compartment control uses two rotary knobs: one for the temperature control and the other for the fan speed control.
INSTRUMENT PANEL AND CONTROLS Rear Rotary Blower Control The second row seat occupants have control of the rear blower speed, only when the front control unit is in the “REAR CONTROL” position. NOTE: For best operation, make sure that ventilation grilles located in the rear storage area are not obstructed by stowed articles. The rear blower switch has an “Off” position and a range of blower speeds. Rotating the rear blower control clockwise will increase the blower speed.
INSTRUMENT PANEL AND CONTROLS 209 Front Unit to Rear Unit Chart If the Front Control is selected Panel Bi-Level • Between Bi-Level Floor Floor Mix Defrost Rear Airflow will come from Headliner Headliner Bi-Level Floor Floor Floor Operating Tips Fast Cooldown For a fast cooldown, set the blower fan to the highest setting, set the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
INSTRUMENT PANEL AND CONTROLS and blower speed to maintain comfort. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. When stopped in heavy traffic, it may be necessary to shift into NEUTRAL and press the accelerator slightly for fast idle operation. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows.
INSTRUMENT PANEL AND CONTROLS 211 Operating Tips Chart 4 I nf or mat i onPr ov i dedby :
INSTRUMENT PANEL AND CONTROLS REAR WINDOW FEATURES Rear Window Wiper/Washer A rotating switch located on the climate control panel turns the rear wiper On or Off. Pressing the rotating switch inward activates the rear window washer. Rotating the switch will enable one of five intermittent delay times for the rear wiper. The delay times range from 20 to 1 second.
INSTRUMENT PANEL AND CONTROLS 213 If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume operation. Rear Window Defrosting A push-button type switch is located in the climate control panel. Press the switch and the rear window defroster and electric remote control heated mirrors (if equipped) will turn On. An amber indicator on the push-button will light when the defroster is turned On.
I nf or mat i onPr ov i dedby :
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 218 ▫ Shifting Procedure - NV 144 Transfer Case . . . 228 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 218 ▫ NV 244 Generation II Transfer Case Operating Information / Precautions . . . . . . . . . . . . . . . 229 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 219 ▫ Shifting Procedure - NV 244 Generation II Transfer Case . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 239 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 256 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 239 䡵 Supplemental Tire Pressure Information . . . . . . . 257 ▫ Tire Identification Number (TIN) . . . . . . . . . . 243 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 244 䡵 Snow Tires . . . . . . . . .
STARTING AND OPERATING 217 䡵 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 266 ▫ Trailer Towing Requirements . . . . . . . . . . . . . 276 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 268 ▫ Trailer Tow Wiring . . . . . . . . . . . . . . . . . . . . 277 ▫ Certification Label . . . . . . . . . . . . . . . . . . . . . 268 ▫ Cooling System Tips—Trailer Towing . . . . . . . 278 ▫ Curb Weight . . . . . . . . . . . . . . . . . . . . . . . . . 269 䡵 Snowplow . . . . . .
STARTING AND OPERATING STARTING PROCEDURES The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Automatic Transmission Start the engine with the selector lever in NEUTRAL or PARK position. Apply the brake before shifting to any driving range. I nf or mat i onPr ov i dedby : WARNING! Do not attempt to push or tow your vehicle to get it started.
STARTING AND OPERATING 219 Normal Starting Normal Starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure. If Engine Fails To Start If the engine fails to start after you have followed the Normal Starting procedure, it may be flooded.
STARTING AND OPERATING WARNING! WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. After Starting The idle speed is automatically controlled on fuel injected engines and will decrease as the engine warms up.
STARTING AND OPERATING 221 WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION Automatic Transmission The electronic PRNDL on the instrument cluster indicates the transmission gear selected. The selector lever is mounted on the right side of the steering column. To drive, move the selector lever from Park or Neutral to the desired drive position.
STARTING AND OPERATING WARNING! WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling the lever toward you, after you have set it in P (Park). Make sure it is in Park before leaving the vehicle. It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed.
STARTING AND OPERATING 223 “N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. “1” First For driving up very steep hills and for engine braking at low speeds 25 mph (40 km/h) or less when going down hill. To prevent excessive engine speed do not exceed 25 mph (40 km/h) in this range.
STARTING AND OPERATING • transmission has reached normal operating temperature. NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level. Refer also to the Note under torque converter clutch, later in this section.
STARTING AND OPERATING 225 performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking.
STARTING AND OPERATING the fluid partially draining from the torque converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position.
STARTING AND OPERATING 227 or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required. Proper operation of four-wheel-drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. WARNING! Because four-wheel-drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit.
STARTING AND OPERATING 4LOCK Four-Wheel-Drive LOCK - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Shifting Procedure - NV 144 Transfer Case AWD to 4LOCK or 4LOCK to AWD With the key ON and the engine either OFF or RUNNING, rotate the transfer case switch, located on the instrument panel to the desired position.
STARTING AND OPERATING 229 NOTE: Delayed shifting out of 4LOCK may be experienced due to uneven tire wear, low tire pressure, or excessive vehicle loading. NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light will flash and the current transfer case position will be maintained.To retry a selection, turn the control knob back to the current position, wait five (5) seconds, and retry the shift.
STARTING AND OPERATING vehicle in the 4LOCK position on dry hard surfaced roads. This feature provides the safety, security, and convenience of operating in all-wheel drive at all times regardless of road conditions. NOTE: The transfer case Neutral (N) position is to be used for recreational towing only. See Recreational Towing section for specific procedures on shifting into and out of Neutral (N).
STARTING AND OPERATING 231 WARNING! positions at a given road speed. Take care not to overspeed the engine and do not exceed 40 km/h (25 mph). Always engage the parking brake when powering down the vehicle if the ⴖService 4WDⴖ light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury. Proper operation of four-wheel-drive vehicles depends on tires of equal size, type and circumference on each wheel.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING 233 wheels to complete the shift. There may be a delay up to 13 seconds for the shift to complete after the wheels have stopped spinning. Shifting Procedure - NV 244 Generation II Transfer Case NOTE: Delayed shifting out of the 4LOCK position may be experienced due to uneven tire wear, low tire pressure, or excessive loading. NOTE: When shifting into or out of 4LO some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants.
STARTING AND OPERATING 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the position indicator light has stopped flashing, shift the transmission back into gear. Alternate Procedure 1. Bring the vehicle to complete stop. 2. With the key ON and the engine either OFF or RUNNING, shift the transmission into NEUTRAL. 3. Rotate the transfer case control switch to the desired position.
STARTING AND OPERATING 235 NOTE: The instrument cluster brake warning light indicates only that the parking brake is applied. You must be sure the parking brake is fully applied before leaving the vehicle. When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should be applied whenever the driver is not in the vehicle. Be sure the parking brake is firmly set when parked and the gear-shift lever is in PARK position.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or vehicle may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park. Failure to do so may cause the vehicle to roll and cause damage or injury. • Be sure the parking brake is fully disengaged before driving, failure to do so can lead to brake failure and an accident. • Leaving children in a vehicle unattended is dangerous for a number of reasons.
STARTING AND OPERATING 237 The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal. The Anti-Lock Brake system includes an amber (ABS) warning light. When the light is illuminated, the AntiLock Brake system is not functioning. The system reverts to standard non-anti-lock brakes. Turning the ignition Off and On again may reset the Anti-Lock Brake system if the fault detected was only momentary.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 239 ROCKING THE VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. TIRE SAFETY INFORMATION Tire Markings The least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING 241 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING 243 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING EXAMPLE: 01 = Number representing the year in which the tire was manufactured.(2 digits) —01 means the year 2001. —Prior to July 2000, tire manufacturers were only required to have 1 number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991.
STARTING AND OPERATING 245 Tire and Loading Information Placard 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING lbs.” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. Steps for Determining Correct Load Limit 6.
STARTING AND OPERATING 247 5 I nf or mat i onPr ov i dedby :
STARTING AND OPERATING 1. Safety— WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 249 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING 251 Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high speed vehicle operation.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only.
STARTING AND OPERATING 253 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING WARNING! WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING 255 These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 257 Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passengers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
STARTING AND OPERATING These cautions apply to all chain traction devices, including link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Durango trucks. NOTE: The use of class “S” chains is permitted on Durangos with P245/70R17 tires. CAUTION! Do not use tire chains on 4x4 Durango trucks equipped with P265/65R17 tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle.
STARTING AND OPERATING 259 TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING FUEL REQUIREMENTS All engines (except 5.7L engines) are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an oc3.7L/4.7L tane rating of 87. The routine use of preEngines mium gasoline is not recommended. Under normal conditions the use of premium fuel will not provide a benefit over high quality regular gasolines and in some circumstances may result in poorer performance. The 5.
STARTING AND OPERATING 261 and durability for your vehicle. We recommend the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT reduce spark plug life and reduce emission system performance. We recommend that gasolines free of MMT be used in your vehicle.
STARTING AND OPERATING 263 NOTE: Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. Make sure that the gas cap is tightened each time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING CAUTION! WARNING! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive.
STARTING AND OPERATING 265 NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • • • • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system. An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monox- • • ide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 267 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.
STARTING AND OPERATING VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration Regulations, your vehicle has a certification label affixed to the driver’s side door. Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the Month, Day, and Hour of manufacture. The bar code that appears on the bottom of the label is your Vehicle Identification Number (VIN).
STARTING AND OPERATING 269 Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded. Each axle GAWR is determined by the component in the system with the lowest load carrying capacity (axle, springs, tires, or wheels). Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle’s GVWR.
STARTING AND OPERATING then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store heavier items down low and be sure that the weight is distributed equally.
STARTING AND OPERATING 271 after the vehicle has been weighed both in its ⴖcurb weightⴖ condition, and in its ⴖloaded and ready for operationⴖ condition. Gross Vehicle Weight Rating (GVWR) 6500 LBS. TRAILER TOWING To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
STARTING AND OPERATING TRAILER SWAY CONTROL is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle.
STARTING AND OPERATING 273 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Be sure the trailer is loaded heavier in front, with 60% to 65% of the weight in front of the axle(s). Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. • Connect trailer lighting and brakes using factory harnesses only. Do not cut or splice any wiring to the brake circuits. Trailer and Tongue Weight Gross Trailer Weight (GTW) means the maximum allowable weight of the trailer plus the weight of all cargo and equipment loaded on the trailer when in actual underway towing condition.
STARTING AND OPERATING 275 Gross Combined Vehicle Weight Rating (GCWR) The Gross Combined Vehicle Weight Rating (GCWR) is the MAXIMUM allowable weight of the towing vehicle, including passengers and cargo, and the weight of the loaded trailer. Calculate the maximum trailer weight (MTW) by subtracting the towing vehicle’s weight, including passengers, and cargo from GCWR. Trailer Towing—Hitches: With a Class IV Hitch, you can tow a trailer with a Gross Trailer Weight of up to 8, 900 lbs. (4037 kg.
STARTING AND OPERATING In Canada, refer to the following website address: http:// www.dodge.ca. Trailer Towing Requirements All Dodge Durango trucks are intended to tow trailers up to 2,000 lbs. (907 kg) without added equipment or alterations to standard equipment. Your vehicle may be factory equipped for safe towing of trailers over 2,000 lbs. (907 kg) with the trailer tow package.
STARTING AND OPERATING 277 Heavy trailer towing also may require breakaway electric trailer brakes, anti-sway devices or equalizing hitches for safe operation. Such devices are commonly required by state law. Trailer Tow Wiring The Trailer Tow Package includes a 4 and 7 pin wiring harness located at the rear underbody of the vehicle. NOTE: Connect trailer lighting and brakes using factory harnesses only. Do not cut or splice wiring to the brake circuits.
STARTING AND OPERATING • Highway Driving Reduce speed. • Air Conditioning Turn off temporarily. • See Cooling System Operating information in the Maintenance section of this manual for more information.
STARTING AND OPERATING 279 SNOWPLOW CAUTION! Dodge Durango Models NOTE: Do not use Dodge Durango Models for snowplow applications. Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! WARNING! Snowplows, winches, and other aftermarket equipment should not be added to the front end or your vehicle. The airbag crash sensors may be affected by the change in the front end structure.
STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) WARNING! Recreational Towing 2WD Models Recreational towing of 2WD models is not allowable. Towing the vehicle with the transmission in Neutral can cause severe transmission damage. Removal of the driveshaft for towing is not recommended since this allows transmission fluid to leak out.
STARTING AND OPERATING 281 NOTE: The NV 244 Generation II transfer case must be shifted into Neutral (N) for recreational towing. The Neutral (N) selection button is located on the lower left hand corner of the 4WD Control Switch. Shifts into and out of transfer case Neutral (N) can take place with the selector switch in any mode position. Shifting into Neutral (N) Use the following procedure to prepare your vehicle for recreational towing. 2. Shut engine OFF. 3.
STARTING AND OPERATING 11. Repeat steps 9 and 10 with the transmission in Drive (D). 12. Turn ignition key to the unlocked OFF position. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not ON, the shift will not take place and no position indicator lights will be on or flashing. 13. Shift automatic transmission into Park (P). 14. Attach vehicle to tow vehicle with tow bar.
STARTING AND OPERATING 283 3. Turn the ignition key to the ON position without starting the engine. 4. Depress brake pedal. 5. Shift automatic transmission to Neutral (N). 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 1 second. 7. After the Neutral (N) indicator light turns off release the Neutral (N) button. 8. After the Neutral (N) button has been released the transfer case will shift to the position identified by the selector switch.
STARTING AND OPERATING 2. Slow down if road has standing water or puddles. CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage internal parts. TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 286 䡵 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 296 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 286 䡵 Emergency Tow Hooks — If Equipped . . . . . . . . 298 䡵 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 288 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . . 299 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES 287 WARNING! WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. Remove the gas cap slowly to prevent fuel spray from the filler neck which may cause injury. I nf or mat i onPr ov i dedby : The volatility of present gasolines may cause a build up of pressure in the fuel tank that may increase while you drive.
WHAT TO DO IN EMERGENCIES CHANGING A FLAT TIRE Jack Location In the Durango, the scissor jack and tire changing tools are stowed under the second row seat. The jack is secured in place with a winged stud and a fixed stud. It is very important to secure the jack tightly in place by engaging the slot in the base to the fixed stud under the middle seat. The winged stud inserts through the eyelet in the end of the jack’s worm screw.
WHAT TO DO IN EMERGENCIES 289 WARNING! The jack is designed as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Removing The Spare Tire The spare tire on the Dodge Durango is located underneath the vehicle in the rear.
WHAT TO DO IN EMERGENCIES Remove the spare tire before attempting to jack the truck. 1. Remove the rubber plug from the floor in the cargo area. 3. Turn the wrench counterclockwise to lower the spare tire. Continue to turn the wrench until the spare tire can be pulled out from under the vehicle. It is recommended that you stow the flat or spare to avoid tangling the loose cable. CAUTION! The winch mechanism is designed for use with the jack extension tube only.
WHAT TO DO IN EMERGENCIES 291 Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. Do not raise this vehicle using a bumper jack.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. (prior to inboard transition. Operate the jack using the jack drive tube and the wheel wrench - the tube extension, may be used but is not required. • Passengers should not remain in the vehicle when the vehicle is being jacked. Instructions 1. Remove the spare wheel, jack, and tools from storage. 2.
WHAT TO DO IN EMERGENCIES 293 the tire as posssible with the drive tubes extending to the rear. Connect the jack tube extension and wheel wrench. 6 Rear Right Jacking Location Rear Left Jacking Location Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack, tools and the extra tire and wheel in the places provided. 5. Remove the wheel nuts and pull the wheel off.
WHAT TO DO IN EMERGENCIES 295 WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • • • • • • Apply the parking brake firmly before jacking. Never start the engine with the vehicle on a jack. Do not let anyone sit in the vehicle when it is on a jack.
WHAT TO DO IN EMERGENCIES Check the Battery Test Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery. JUMP STARTING WARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other.
WHAT TO DO IN EMERGENCIES 297 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. 3. Damage to charging system of booster vehicle or of immobilized vehicle. EMERGENCY TOW HOOKS — IF EQUIPPED Your vehicle may be equipped with emergency tow hooks.
WHAT TO DO IN EMERGENCIES 299 CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle. Use of safety chains is recommended. Attach towing device to main structural members of the vehicle — not to bumpers or associated brackets.
WHAT TO DO IN EMERGENCIES NOTE: Towing the vehicle at more than 30 mph (50 km/h) or for more than 15 miles (25 km ) can cause severe transmission damage.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment 3.7L V6 . . . . . . . . . . . . . . 304 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . . 310 䡵 Engine Compartment 4.7L V-8 . . . . . . . . . . . . . . 305 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 311 䡵 Engine Compartment 5.7L HEMI V-8 . . . . . . . . . 306 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 314 䡵 Onboard Diagnostic System — OBD II . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Catalytic Converter . . . . . . . . . . . . . . . . . . . . 317 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 332 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 318 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . 335 ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 319 ▫ Axles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 ▫ Power Steering — Fluid Check . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 303 ▫ Headlights/Parking/Turn Signal . . . . . . . . . . 349 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 357 ▫ Rear Side Marker, Tail Lights, Turn Signals And Backup Lights — Replacement . . . . . . . . . . . . 350 䡵 Recommended Fluids, Lubricants And Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359 ▫ License Lights . . . . . . . . . . . . . . . . . . . . . . . . 354 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 3.
MAINTAINING YOUR VEHICLE 305 ENGINE COMPARTMENT 4.
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 5.
MAINTAINING YOUR VEHICLE 307 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 309 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The MIL light will blink for approximately 5 seconds and then remain on until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE 311 Engine Oil Checking Engine Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about 5 minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight. 7. Add oil only if the level is below the “SAFE” range (at or below the “ADD” mark) on the engine oil level indicator (dipstick).
MAINTAINING YOUR VEHICLE CAUTION! • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine. • Trailer towing, Taxi, Police or delivery service (commercial service). Frequency Of Oil Change Road conditions and your style of driving affect the interval at which your oil should be changed.
MAINTAINING YOUR VEHICLE 313 Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine. Under these conditions, special attention should be given to the engine air cleaner and the crankcase inlet air cleaner. The crankcase ventilation system should also be checked periodically. Make sure that these units are always clean. This will tend to reduce to a minimum the amount of abrasive material that may enter the engine.
MAINTAINING YOUR VEHICLE temperature starting and vehicle fuel economy. Refer to your engine oil filler cap for the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, see the Engine Compartment illustration in this section. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used.
MAINTAINING YOUR VEHICLE 315 Engine Oil Filter Selection The manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar威 Engine Oil Filters are a high quality oil filter and are recommended. Drive Belts — Check Condition and Tensioner Belt tension is controlled by means of an automatic tensioner.
MAINTAINING YOUR VEHICLE CAUTION! WARNING! When replacing plugs, do not overtighten. You could damage them and cause them to leak. The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury.
MAINTAINING YOUR VEHICLE 317 Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE 319 WARNING! CAUTION! Battery posts, terminals, and related accessories contain lead and lead compounds. Always wash hands after handling the battery. It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE 321 WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE attention should also be given to hood latching components to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant directly into the lock cylinder.
MAINTAINING YOUR VEHICLE 323 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, follow the preceding safety tips. Cooling System Inspection Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
MAINTAINING YOUR VEHICLE 325 WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood don’t open the hood until the radiator has had time to cool. If you open the hood and see steam or hot coolant escaping from the radiator, don’t touch anything. Get away quickly. Never try to open a pressure cap when the radiator is hot.
MAINTAINING YOUR VEHICLE Recommended Engine Coolant This vehicle has been factory filled with an Ethylene Glycol based engine coolant with long life corrosion inhibitors (called HOAT, for Hybrid Organic Additive Technology). Follow the “Maintenance Schedule” for the recommended coolant change intervals. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE 327 Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOAT ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution.
MAINTAINING YOUR VEHICLE WARNING! The warning words “DO NOT OPEN HOT” on the coolant pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap when the system is hot or under pressure. The radiator normally remains completely full, so there is no need to remove the pressure cap except checking coolant freeze point or replacement with new antifreeze coolant.
MAINTAINING YOUR VEHICLE 329 D. Maintain coolant concentration at 50% HOAT ethylene glycol engine coolant (minimum) and distilled water for proper corrosion protection of your engine. E. Make sure that the radiator and coolant bottle overflow hoses are not kinked or obstructed. F. Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean also. G. The thermostat should not be changed for summer or winter operation.
MAINTAINING YOUR VEHICLE You are urged to use only the manufacturer’s specified hoses and clamps, or their equivalent in material and specification, in any fuel system servicing. It is mandatory to replace all clamps that have been loosened or removed during service. Care should be taken in installing new clamps to insure they are properly torqued.
MAINTAINING YOUR VEHICLE 331 Brake Master Cylinders The fluid level in the master cylinders should be checked whenever the vehicle is serviced, or immediately if the brake system warning light is on. If necessary, add fluid to bring level to the full mark on the side of the reservoir of the brake master cylinder. Be sure to clean the top of the master cylinder area before removing the cap. With disc brakes, fluid level can be expected to fall as the brake pads wear.
MAINTAINING YOUR VEHICLE CAUTION! WARNING! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified. Inspect hydraulic brake hoses for surface cracking, scuffing or worn spots.
MAINTAINING YOUR VEHICLE 333 1. Operate the engine at idle speed and normal operating temperature. a minimum of two (2) minutes for the oil to fully drain into the transmission before rechecking the fluid level. 2. The vehicle must be on level ground. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD” (lower) holes on the dipstick with the fluid at approximately 70°F ( 21°C) (room temperature).
MAINTAINING YOUR VEHICLE CAUTION! that the transmission fluid be maintained at the prescribed level using the recommended fluid. Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. CAUTION! Using a transmission fluid other than the manufacturers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
MAINTAINING YOUR VEHICLE 335 fluid leaks. The use of transmission sealers should be avoided, since they may adversely affect seals. Transfer Case Inspect the transfer case for fluid leaks. If a fluid leak is evident the transfer case fluid level may be low. Have the transfer case serviced immediately. CAUTION! Damage may result from operation of the vehicle with low transfer case fluid. The transfer case fluid should be drained and refilled at the intervals specified.
MAINTAINING YOUR VEHICLE Front Axle Front Axle fluid level should be 3/4” (20 mm) below the bottom of the fill hole. Selection of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for chassis components. This symbol, an example shown below, is located on the grease container and identifies the application and quality of the grease.
MAINTAINING YOUR VEHICLE 337 Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
MAINTAINING YOUR VEHICLE 339 • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar威 touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar威 Fabric Cleaner to clean fabric upholstery and carpeting.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using.
MAINTAINING YOUR VEHICLE 341 POWER DISTRIBUTION CENTER (FUSE/RELAY) Your vehicle is equipped with two electrical power distribution centers located next to each other in the left side of the engine compartment. The power distribution centers house new plug-in “Maxi” fuses which replace all the in-line fusible links previously used. The power distribution centers also contain “Mini”fuses and plug-in “ISO” relays.
MAINTAINING YOUR VEHICLE fuse to be disconnected, without removing it from the fuse block. Pressing the I.O.D. fuse back into the cavity reconnects it. Interior Fuses The fuse block contains blade-type mini-fuses, relays, and circuit breakers for high-current circuits. It is located in the left kick panel. It is accessible through a snap-in cover.
MAINTAINING YOUR VEHICLE 343 Cavity Fuse/Color F1 15 Amp Blue F2 10 Amp Red F3 10 Amp Red F4 Fuse Block I nf or mat i onPr ov i dedby : 10 Amp Red Description Instrument Cluster Battery Feed Occupant Classification Module (OCM) Battery Feed Ignition Run/ Start for Controller (NGC), Integrated Power Module (IPM), AC Relay and Fuel Pump Relay Door Node and Non-Memory Power Mirror Switch Battery Feed 7
MAINTAINING YOUR VEHICLE F5 F6 F7 F8 F9 F10 F11 F12 Airbags (2 Fuses in Yellow Holder) Ignition Run/ 10 Amp Red Start Unlock Radio Battery 25 Amp Natural Feed Ignition Run/ Start fro 10 Amp Red Cluster/Transfer Case/Seat Sw.
MAINTAINING YOUR VEHICLE 345 F19 F20 15 Amp Blue 25 Amp Natural Heating & Air Conditioning w/ATC Only Battery Feed Amplifier Battery Feed Underhood Fuses (Power Distribution Center) Cavity 1 2 3 4 5 6 7 Fuse/Color 40 Amp Green 30 Amp Pink 30 Amp Pink 30 Amp Pink 50 Amp Red 50 Amp Red 30 Amp Pink Description HVAC Blower Cavity 8 9 10 11 12 13 Power Outlets Rr Wiper/Ign R/O ABS Pump Cabin Htr 1 (Diesel Only) ASD Rr HVAC (XK) 14 15 16 17 18 I nf or mat i onPr ov i dedby : Fuse/Color 40 Amp Green S
MAINTAINING YOUR VEHICLE Cavity 19 20 21 22 23 24 25 26 27 Fuse/Color 20 Amp Yellow 20 Amp Yellow 30 Amp Pink Spare 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Lt. Blue 15 Amp Lt. Blue Description Ign Sw Cavity 28 PCM Batt (Gasoline Only) 29 30 31 Fuse/Color 25 Amp Natural Spare Spare Mini Relay FDCM/E-Diff.
MAINTAINING YOUR VEHICLE 347 Underhood Fuses (Integrated Power Module) Cavity 1 2 3 4 5 6 7 8 9 10 11 12 13 Fuse/Color Micro Relay Micro Relay Micro Relay Micro Relay Micro Relay Micro Relay Micro Relay 10 Amp Red 10 Amp Red 10 Amp Red Mini Relay 20 Amp Yellow 20 Amp Yellow Description Wiper On/Off Rly Wiper Hi/Lo Rly Horn Rly Rear Fog Rly (BUX Only) Lt T-Tow Stop/Turn Rly Rt T-Tow Stop/Turn Rly Park Lamps Rly Lt Park Lamps T-Tow Park Lamps Rt Park Lamps Rad Fan Hi Rly FCM Batt #4 Cavity 14 15 16 17 18
MAINTAINING YOUR VEHICLE Cavity 23 24 25 26 27 28 29 30 Fuse/Color 50 Amp Red Mini Relay Micro Relay Micro Relay 15 Amp Lt. Blue 20 Amp Yellow 10 Amp Red 10 Amp Red Reading Light . . . . . . . . . . . . . . . . . . . . . . . WL212–2 Visor Vanity Lights . . . . . . . . . . . . . . . Not Serviceable Description Rad Fan Rad Fan Lo Rly Ft Fog Lamps Rly Adjustable Pedal Rly IOD #1 LIGHT BULBS — Outside Bulb No. Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 349 2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by removing the fender panel access door which is located in the wheel liner. BULB REPLACEMENT Headlights/Parking/Turn Signal 3. Grasp the headlight and pull firmly to disengage the headlight from the fender panel. 4. While firmly holding the headlight in your hands disconnect all connectors by following the procedure described in step number 5 below. 1.
MAINTAINING YOUR VEHICLE 6. Twist and remove socket from lamp. 7. Remove bulb from socket and replace. NOTE: These are Halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat build-up which reduces bulb life. Rear Side Marker, Tail Lights, Turn Signals And Backup Lights — Replacement 1. Remove the two push-pins from the tail light housing.
MAINTAINING YOUR VEHICLE 351 2. Rotate the light to the outboard side of the vehicle and remove.
MAINTAINING YOUR VEHICLE 3. Unlock and remove electrical connector. 4. Remove the three screws holding the bulb strip to the back of the tail lamp.
MAINTAINING YOUR VEHICLE 353 5. Remove the bulb strip from the tail light lens. 6. Remove bulbs from bulb strip by pulling the bulb straight out.
MAINTAINING YOUR VEHICLE License Lights 1. Remove the two screws securing the lens to the liftgate.
MAINTAINING YOUR VEHICLE 355 2. Rotate the socket 1/4 turn counterclockwise. Center High-Mounted Stoplight 1. Remove two screws securing stoplight housing assembly to the liftgate. 7 3. Pull bulb from socket.
MAINTAINING YOUR VEHICLE 2. Turn socket 1/4 counterclockwise and free from housing. Fog Lights 1. Rotate bulb and connector 1/4 turn counterclockwise. 2. Pull bulb off of connector. NOTE: For foglights ensure that the takeout pushfasteners are relocated back in their positions; one in the foglight molding and the other in the hydroform. 3. Pull bulb straight from socket to remove.
MAINTAINING YOUR VEHICLE 357 FLUIDS AND CAPACITIES U.S. Metric 27 Gal. 27 Gal 102L 102L 5 Qt. 6 Qt. 7 Qt. 4.7L 5.7L 6.6L 13.5 Qt. 12.9L 14.5 Qt. 13.8L 13.1 Qt. 12.5L Fuel 3.7L/4.7L, 87 Octane 5.7L, 89 Octane Engine Oil (with filter) 3.7L, SAE 5W-30, API Certified 4.7L, SAE 5W-30, API Certified 5.7L, SAE 5W-20, API Certified Cooling System (includes 2.1 Qts./2L for coolant bottle 3.7L without Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 3.
MAINTAINING YOUR VEHICLE 4.7L with Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L without Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L with Rear Heat (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) NOTE: All fluid capacities are approximate. I nf or mat i onPr ov i dedby : U.S. Metric 14.2 Qt. 13.5L NA NA 16.6 Qt. 15.
MAINTAINING YOUR VEHICLE 359 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant 3.7/4.7L Engine Oil 5.7L Engine Oil Engine Oil Filter Spark Plugs Fuel Selection 3.7L/4.7L Fuel Selection 5.7L Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) P/N 5011764AB or equivalent. Use SAE 5W-30, API Certified, meeting material standard MS-6395 or equivalent.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar威 ATF+4, Automatic Transmission Fluid or equivalent. Mopar威 ATF+4, Automatic Transmission Fluid or equivalent. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant or equivalent. SAE 75W-140 Synthetic Gear Lubricant or equivalent. Mopar威 DOT 3 and SAE J1703 should be used or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 362 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 366 䡵 Emissions Testing . . . . . . . . . . . . . . . . . . . . . . . 362 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 377 C 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 363 䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 362 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES 363 M MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures are below 32° F (0° C). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
M A I N T E N A N C E S C H E D U L E S 364 MAINTENANCE SCHEDULES Use the schedule that best describes your driving conditions. Where time and mileage are listed, follow the interval that occurs first. At Each Stop for Fuel NOTE: Under no circumstances should oil change intervals exceed 6000 miles (10 000 km) or 6 months whichever comes first. • Check the engine oil level about 5 minutes after a fully warmed engine is shut off.
MAINTENANCE SCHEDULES 365 M A I N T Change the engine oil filter. E N Inspect the exhaust system. A N Inspect the brake hoses. C Inspect the CV joints (if equipped) and front suspen- E Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed.
M A I N T E N A N C E S C H E D U L E S 8 366 SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
SCHEDULE “B” 367 M Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect engine air cleaner filter, replace if necessary.
M 368 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Change rear axle fluid. S C H E D U L E S 18,000 (29 000) X X Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.
SCHEDULE “B” 369 M Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
M 370 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Change rear axle fluid. S C H E D U L E S 8 48,000 (77 000) X X Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect and replace ignition cables if necessary (5.7L only). Inspect auto tension drive belt and replace if required.
SCHEDULE “B” 371 M Miles (Kilometers) Drain and refill automatic transmission fluid, change filter (3.7L). This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing. Drain and refill automatic transmission fluid and change main sump filter (4.7L/5.7L only). This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing. Inspect transfer case fluid (4X4).
M 372 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Change rear axle fluid. S C H E D U L E S 63,000 (101 000) X 66,000 (106 000) X X Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Inspect auto tension drive belt and replace if required.
SCHEDULE “B” 373 M Miles (Kilometers ) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
M 374 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, or at 3 A months whichever comes first. N C Rotate tires. E Flush and replace engine coolant, if not replaced at S C H E D U L E S 93,000 (149 000) X 60 months. Change rear axle fluid. Change front axle fluid (4X4).
SCHEDULE “B” 375 M Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect and replace ignition cables if necessary (5.7L only). Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required. Drain and refill transfer case fluid (4X4).
M 376 SCHEDULE “B” A I N Miles T (Kilometers) E N Drain and refill automatic transmission fluid, A change filter (3.7L). This applies only if your N vehicle is used for police, taxi, fleet, or freC quent trailer towing. E S C H E D U L E S 8 105,000 (168 000) Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped. (4.7L/5.7L only). This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing.
SCHEDULE “A” 377 M Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace as necessary. Replace spark plugs.
M 378 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Check transfer case fluid level (4X4). S C H E D U L E S 8 Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (163 000 km). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary. * Inspect and replace ignition cables if necessary (5.7L only).
SCHEDULE “A” 379 M Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
M 380 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Drain and refill tranfer case fluid (4X4). S C H E D U L E S 8 102,000 (163 000) [102] X X Flush and replace engine coolant, if not replaced at 60 months. Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (163 000 km). Inspect brake linings. Inspect engine air cleaner filter, replace as necessary. Replace spark plugs.
SCHEDULE “A” 381 M A • The transfer case should be placed in the 4HI mode I N and kept in this position to minimize the battery drain. T WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. E • As an alternative to the above steps you may discon- N A nect the negative cable from the battery.
I nf or mat i onPr ov i dedby :
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384 ▫ Prepare For The Appointment . . . . . . . . . . . . 384 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 384 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 384 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 385 䡵 Warranty Information (U.S. Vehicles Only) . . . . . 387 䡵 Mopar威 Parts . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 385 IF YOU NEED ASSISTANCE The manufacturer and its dealers are vitally interested in your satisfaction. We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
IF YOU NEED CONSUMER ASSISTANCE DaimlerChrysler Motors Corporation Customer Center P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: (800) 992-1997 DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone —(800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F.
IF YOU NEED CONSUMER ASSISTANCE 387 contract, call the manufacturer’s Service Contract National Customer Hotline at 1-800-521-9922. The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract.
IF YOU NEED CONSUMER ASSISTANCE U.S.
IF YOU NEED CONSUMER ASSISTANCE 389 MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. • Diagnostic Procedure Manuals.
IF YOU NEED CONSUMER ASSISTANCE 391 Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.
I nf or mat i onPr ov i dedby :
INDEX 10 I nf or mat i onPr ov i dedby :
INDEX ABS (Anti-Lock Brake) System . . . . . . . . . . . . 167,236 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . 262,286 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 316 Air Conditioner Maintenance . . . . . . . . . . . . 198,319 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 197 Air Conditioning, Operating Tips . . . . . . . . . . . . 209 Air Conditioning, Rear Zone . . . . . . . . . . . . . . . . 201 Air Conditioning Refrigerant . . . . . . . . . . . . .
INDEX 395 Axle Lubrication . . . . . . . . . . . . . . . . . . . . . . . . 335 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 296 Gas Caution . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Keyless Transmitter Replacement . . . . . . . . . . . .
INDEX Cargo Organizer . . . . . . . . . . . . . . . . . . . . . . . 156 Cargo Organizer . . . . . . . . . . . . . . . . . . . . . . . . 156 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 268 Catalytic Converter . . . . . . . . . . . . . . . . . . . . 266,317 CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 173,179 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 78,197 Center High Mounted Stop Light . . . . . . . . . . . . 355 Certification Label . . . . . . .
INDEX 397 Points to Remember . . . . . . . . . . . . . . . . . . . . 328 Radiator Cap . . . . . . . . . . . . . . . . . . . . . . . . . 327 Selection of Coolant . . . . . . . . . . . . . . . 326,357,359 Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 164 Cruise Control (Speed Control) . . . . . . . . . . . . . . 132 Cup Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Customer Assistance . . . . . . . . . . . . . . . . . . . . . 385 Data Recorder, Event . . . . . . . . . . . .
INDEX Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299 Emission Control System Maintenance . . . . . . . . . 362 Emission Related Components . . . . . . . . . . . . . . 329 Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 316 Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . 220 Break-In Recommendations . . . . . . . . . . . . . . . . 64 Compartment . . . . . . . . . . . . . . . . . . . . . . 305,306 Coolant (Antifreeze) . . . . . . . . . . . . . .
INDEX 399 Turn Signal . . . . . . . . . . . . . . . . . . . . . 125,164,350 Flat Tire Stowage . . . . . . . . . . . . . . . . . . . . . 289,295 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 219 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . 331,360 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 357 Fluid Level Checks Automatic Transmission . . . . . . . . . . . . . . . . . 332 Brake . .
INDEX Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 166 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 Gross Axle Weight Rating . . . . . . . . . . . . . . . . . . 269 Gross Cargo Weight . .
INDEX 401 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . 164 Instrument Panel and Controls . . . . . . . . . . . . . . 162 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 340 Integrated Power Module . . . . . . . . . . . . . . . . . . 347 Interior Appearance Care . . . . . . . . . . . . . . . . . . 339 Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 342 Interior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 121 Interior Lights . . . . . . . . . . . .
INDEX Hazard Warning Flasher . . . . . . . . . . . . . . . . . 286 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 High Beam/Low Beam Select . . . . . . . . . . . . . 126 Instrument Cluster . . . . . . . . . . . . . . . . . . 123,164 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . 121,136 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354 Lights On Reminder . . . . . . . . . . . . .
INDEX 403 Schedule ⬙A⬙ . . . . . . . . . . . . . . . . . . . . . . . . . 377 Schedule ⬙B⬙ . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Malfunction Indicator Light . . . . . . . . . . . . . . 170,308 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 390 Manual Transmission Lubricant Selection . . . . . . . . . . . . . . . . . . . . . 360 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . . 136 Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Mirrors .
INDEX Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . 75 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . 167,223 Overdrive OFF Switch . . . . . . . . . . . . . . . . . . . . 223 Overhead Console . . . . . . . . . . . . . . . . . . . . 135,136 Overhead Travel Information Center . . . . . . . . . . 136 Overheating, Engine . . . . . . . . . . . . . . . . . . . 166,327 Owner’s Manual . . . . . . . . . . . . . . . . . . . . . . . . 390 Panic Alarm . . . . . . . . . . . . . . . . .
INDEX 405 Radio Broadcast Signals . . . . . . . . . . . . . . . . . . . 172 Radio Operation . . . . . . . . . . . . . . . . . . . 173,179,197 Radio Reception . . . . . . . . . . . . . . . . . . . . . . . . 172 Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Radio (Sound Systems) . . . . . . . . . . . . . . . . . 173,179 Rear Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 Rear Window Defroster . . . . . . . . . . . . . . . . . . . 213 Rear Window Features . . . .
INDEX Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Satellite Radio . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 194 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 363 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . 340 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . 36 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 407 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Signals, Turn . . . . . . . . . . . . . . . . . . . . . 125,164,350 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . 257 Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . 252,253 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Tire Identification Number (TIN) . . . . . . . . . . . . . 243 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 239 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66,248 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 248 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Changing . . . .
INDEX 409 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Minimum Requirements . . . . . . . . . . . . . . . . . 276 Trailer and Tongue Weight . . . . . . . . . . . . . . . . 274 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Trailer Towing Guide . . . . . . . . . . . . . . . . . . . . . 275 Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Automatic . . . . . . . . . .
INDEX Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 5 Warranty Information . . . . . . . . . . . . . . . . . . . . . 387 Washers, Windshield . . . . . . . . . . . . . . . . . . . . . 127 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 337 Weight Load Carrying . . . . . . . . . . . . . . . . . . . . 268 Wheel Alignment and Balance . . . . . . . . . . . . . . . 256 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 338 Wheel Changing . . . . . . . . . . . . .
NOTES I nf or mat i onPr ov i dedby :
NOTES I nf or mat i onPr ov i dedby :
NOTES I nf or mat i onPr ov i dedby :
NOTES I nf or mat i onPr ov i dedby :
NOTES I nf or mat i onPr ov i dedby :
NOTES I nf or mat i onPr ov i dedby :
