Edge + Dock

Howell 400™
DOCK HARDWARE REQUIRED
Description QTY
99-013-F Chain Retainer 2
93-122-F
Backer Plate 4
OR
99-001-F HD Anchor Chain Corner 2
99-004-F Outside Corner 2
3/8” x 2-1/2” Carriage Bolts and nuts 16 each
OR
1/2” x 2 1/2” Carriage Bolts and nuts 16 each
3/8” chain QTY to suit application
91-120-F Dock Anchor 2
99-001-F
HD Anchor
Chain Corner (see placement guide)
IMPORTANT: DockEdge+ Inc. assumes no responsibility or liability for the accuracy or representation of the graphic illustrations shown in this hardware guide. These graphic
illustrations are not intended to be architectural drawings, and are not to be substituted for engineered drawings. Each is intended as a guideline ONL
Y. DockEdge+ Inc. does not warrant the
quantities and/ or bill of materials to be accurate in all uses and applications. Individual dock structures may vary by necessity, preference or design. It may be necessary to vary the amount
of materials listed in this guide depending on dock size, material usage, necessity and/ or the severity of the conditions to which the dock structure is subjected to.
All graphic illustrations are based on the use of conventional framework of 2” x 6” lumber and decking lumber. Freeboard may be adjusted by using 2”x8” or 2”x10” lumber. Substitutions in
lumber and hardware placement may effect floatation.
FLOATING AND STATIONARY DOCK
HARDWARE GUIDE
STATIONARY DOCK HARDWARE
93-122-F
Backer Plate
99-011-F
F
emale T
Connector
99-012-F
Male T
Connector
99-004-F
Outside Corner
93-122-F
Backer Plate
92-104-F
Inside Corner
93-122-F
Backer Plate
99-010-F
Female
C
orner Hinge
99-009-F
Male Corner
Hinge
99-001-F
HD Anchor
Chain Corner
91-112-F
HD Connector Hinge
93-122-F
Backer Plate
FLOATING DOCK HARDWARE
PLACEMENT for CORNERS &
HINGES
FLOATING DOCK
ANCHORAGE
93-122-F
Backer Plate
99-001-F
HD Anchor Chain Corner
OR
92-116
Inside Anchor Corner
99-242-F
Howell 400™
Float
99-242-F
Howell 400™
F
loat
99-001-F
HD Anchor Chain Corner
99-004-F
Outside Corner
92-104-F
Inside
Corner
93-122-F
Backer Plate
9
3-122-F
Backer Plate
99-002-F
Joist Corner
99-006-F
Washer Plate
FLOTATION CAPACITY FORMULAE, REQUIRED # OF FLOATS
Howell 550™: (Square Footage of Dock x 25 )/ 550= # of Floats
Howell 400™: (Square Footage of Dock x 25 )/ 400= # of Floats
Formulae based on average use of residential dock at 25lb/ ft.
2
Hardware Placement Guide
Correct Usage of Hardware with Backer Plates
Galvalume
Leg Pipe
93-168-F &
93-110-F
Adjustable Leg Brace Set
Max extension of 72”
89-101-F
Plastic Leg Cap
91-111-F
Corner Leg
Brace Holder
87-107-F
Bottom Pad, 12”
94-102-F
Side Leg Holder
(see placement guide)
86-101-F
Corner Leg Holder
(see placement guide)
86-100-F
Base Plate
86-102-F
Leg Brace Holder
93-105-F
Connector Hinge
(see placement guide)
86-103-F
Joist Corner Bracket
95-122-F
Corner Plate
(see placement guide)
86-104-F
Anchor
Tie Down
Corner
91-116-F
Backer Plate
(see placement guide)
87-122-F
www
.dockedge.com
99-013-F
Chain
Retainer
91-120-F
Dock Anchor
®
THE FINEST QUALITY DOCK HARDWARE AND MARINE ACCESSORIES
The Side Leg Holder
86-101-F may be
mounted inside the
dock framing or out-
side for convenient
adjustment if needed.
87-122-F Backer Plate MUST be used On Opposite
Side Of All Fittings as shown in the Hardware
placement Guide above.
®
Howell 550™
Proper hardware place-
ment for 86-101 & 86-100
leg holders.
Always use
backer plates 87-122 as
shown.