User Manual
22
2 . A protective lens cover should be placed around
the magnier to prevent scratches when not being
used.
POST ELEVATING HANDWHEEL
1. This option allows the operator to adjust the post
and upper saw guide by means of a handwheel
located on the right side of the sawing head. Turn
the handwheel clockwise to "raise" the post, coun-
terclockwise to "lower" it.
WORKTABLE OPTIONS
30" x 30" Worktable
1. Your machine may be equipped with a factory-in-
stalled 30 x 30 inch (762.0 x 762.0 mm) worktable
in place of the standard 26 x 26 inch (660.4 x 660.4
mm) worktable. Load capacity is 500 pounds (226.8
kg).
18" Stroke Worktable
1. This factory-installed air-powered worktable has a
18 inch (457.2 mm) stroke instead of standard 12
inch (304.8 mm) stroke. The table's working surface
is 24 by 36.5 inches (609.6 by 927.1 mm).
Glide Table
1. This worktable option has a 26 by 26 inch (660.4
by 660.4 mm) worktable and table travel of 10-3/4
inches (273.0 mm). It can not be tilted. Load ca-
pacity is 200 pounds (90.7 kg).
2. The workpiece is securely clamped to the table.
The operator then holds the handle in front of the
table and manually pushes the table with the work-
piece through the saw band. The handle also acts
as a workstop if desired.
DO NOT force workpiece through the saw
band.
3. A thumbscrew located in the lower right under the
worktable locks the worktable in place to allow load-
ing and unloading of stock. Loosen the thumbscrew
completely for the worktable to move freely.
4. Air power feed option can be added to assist in
moving the workpiece through the saw band.
5. The handle must be removed for saw band chang-
ing.
CHIP BLOWER
1. The operator can remove chips from the sawing
area by using the chip blower. Shop air is used to
deliver air to the cutting area.
2. Adjust the exible hose and nozzle to direct chips
away from the sawing area.
3. The air supply connection is located on the left
side of the machine on the drive compartment wall.
Incoming air supply should be between 80 and 90
psi (5.6 and 6.3 kg/cm²).
DO NOT exceed 90 psi (6.3 kg/cm²).
MIST COOLANT
1. Using shop air, this option has a valve with sight
glass and a one (1) quart (0.95 liter) supply bottle
mounted on the rear side of the head.
2. Air and coolant are mixed in a manifold to form
a ne mist. Adjust the exible tube to direct mist
stream onto saw band and workpiece to lubricate
and cool the cutting area. Regulate mist with ad-
justable valve at a rate of one drop per second as
seen through the sight glass.
3. The air supply connection is located on the left
side of the machine on the drive compartment wall.
Incoming air supply should be between 80 and 90
psi (5.5 and 6.2 bar or 5.6 and 6.3 kg/cm²).
DO NOT exceed 90 psi (6.2 bar or 6.3 kg/
cm²).
4. Your DoALL sales representative can provide
complete information on various coolants and their
applications
.
BAND MIST LUBRICATOR
1. See the instructions sent with the unit for information
on operation and adjustments.
WORKLIGHT
1. The worklight illuminates the cutting area and areas
nearby and is controlled by an "on/off" switch on the
lamp, or by selector switch on the electrical control
box.
MAGNIFIER
1. Magning the cutting area may prove helpful dur-
ing delicate sawing procedures. This is done by
placing a magning lens around the shade of the
worklight.