User Guide

XR500 Series Canadian Programming Guide Digital Monitoring Products
21
deviCe SeTuP
6.15.9
REQUIRE SITE
CODE? NO YES
Require Site Code
Press the top row Select key under YES to use a site code.
InadditiontoUserCodeverication,dooraccessisonlygrantedwhenanyonesite
codeprogrammedattheSITECODEENTRYoptionmatchesthesitecodereceivedin
theWiegandstring.
6.15.9 .1
SITE CODE 1: -
Site Code Display
 Youcanprogramuptoeightthree-digitsitecodes.Sitecoderangeis0-999.
Any previously programmed site codes display. Dashes represent blank site
codes.
 SiteCode1displaysrst.Enterathree-digitsitecodenumberfollowedby
the command key to advance to the next prompt, Site Code 2. To delete
an existing site code, press any select key. Either enter a new site code
followed by command, or press command to leave blank and continue to the
 nextsitecode.Repeatthesestepstochange,delete,oraddupto8site
codes.
Note: A card with a site code greater than three digits cannot be used.
Use only cards with three-digit site codes.
6.15.10
NO OF USER CODE
DIGITS: 5
Number of User Code Digits
The734modulerecognizesusercodesfromfourtotendigitsinlength.Pressany
toprowSelectkeytoenterausercodedigitlengthbetween4-10digits.This
number must match the user code number length being used by the panel. Default
is5.ForanXR500AreaSystem,use4to10digits(typically5).Forallothersystems
and panels, use 4 digits.
Anyselectionabove5digitsrequireentryofthecustomcarddenitionswithcustom
siteandusercodepositionsfortheWiegandstring.Whensearchingthebitstring
fortheusercode,thedigitsareidentiedandreadfromlefttoright.
6.15.11 Degraded Mode
Thisoptiondenestherelayactionwhencommunicationwiththepanelhasnot
occurredforveseconds.PressanytoprowSelectkeytodisplayrelayaction
options.PresstheBackArrowkeytoreturntotheNOOFUSERCODEDIGITS:.
Choose the Degraded Mode Action required.
 PresstherstSelectkeytochooseOFF[Default] (RelayAlwaysOff) — The relay
doesnotturnonwhenanyWiegandstringisreceived.OffdoesnotaffectanyREX
operation.
 PressthesecondSelectkeytochooseSITE(AcceptSiteCode) — Door access
isgrantedwhentheWiegandsitecodestringreceivedmatchesanysitecode
programmedatSITECODEENTRY.FordetailsreferbacktotheREQUIRESITECODE
option.
 PressthethirdSelectkeytochooseANY(AnyWiegandRead) — Door access is
granted when any Wiegandstringisreceived.
Press the fourth Select key to chooseON(RelayAlwaysOn)—Therelayisalwayson.
 PresstheCOMMAND key to display the next action.
 PresstherstSelectkeytochooseLAST(KeepLastState) — The relay remains in the
same state and does not change when communication is lost.
Afterchoosingtheaction,theDEGRADEDMODEoptionandthenewlydenedaction
display.
Programmingisnowcomplete.PresstheCOMMANDkeytodisplayDEVICENO.Press
the Back Arrow toreturntotheNOOFUSERCODEDIGITSoption.
DEGRADED MODE:
RELAY ALWAYS OFF
DEGRADED MODE:
ACCEPT SITE CODE
DEGRADED MODE:
ANY WIEGAND READ
DEGRADED MODE:
RELAY ALWAYS ON
DEGRADED MODE:
OFF SITE ANY ON
DEGRADED MODE:
PRESERVE LAST
DEGRADED MODE:
LAST