Analog Resistive Touch Screen Controller TSC-30/IC product specification
TSC-30/IC Product Specification Table of Contents 1. Products outline ........................................................................................................... 2 1-1. Scope of Application................................................................................................................... 2 1-2. Outline......................................................................................................................................... 2 1-3. Features ......................
TSC-30/IC Product Specification 1. Products outline 1-1. Scope of Application This specification applies to the TSC-30/IC. 1-2. Outline TSC-30/IC is an analog touch screen control IC that performs A/D conversion on analog signal for the 4-wire, 5-wire and 8-wire resistive analog touch screen, and transmits coordination data with 10bit resolution to the host in a 9600bps serial (asynchronous) and USB. At the coordinate detection, internal filtering process provides a stabilized coordinate value.
TSC-30/IC Product Specification 1-4. General specification Item Power supply voltage Rating Notes DC 3.00V to 5.25V 125mW (standard) Power supply voltage is 5V. 30mW (standard) Power supply voltage is 3.3V.
TSC-30/IC Product Specification PANEL_THOb1 PANEL_THOb2 PANEL_THOb3 PEN_UP USB_PW BEEP RxD_I 41 40 39 38 37 36 35 33 PANEL_THOa 42 34 PANEL_THI 43 44 45 EEP-DO/JP12 47 46 EEP-DI/JP11 48 2.
TSC-30/IC Product Specification 3. Pin functions Pin number Pin name I/O 1 PANEL_AD_XL I Touch Screen XL input pin. 2 PANEL_AD_XR I Touch Screen XR input pin. 3 SW0 I SW0 input pin; H=ON=1, L=OFF=0. 4 SW1 Functional description I SW1 input pin; H=ON=1, L=OFF=0. 5 I Unused pin. Via resistance; Vcc is connected. 6 I Unused pin. Via resistance; Vcc is connected. 7 CNVss P Vss is connected. 8 RESET I Reset input pin (active L).
TSC-30/IC Product Specification 40 PANEL_THOb2 I/O Touch screen control pin. Used only in 5-wire mode. In 4-wire/8-wire mode, opened. 41 PANEL_THOb1 I/O Touch screen control pin. Used only in 5-wire mode. In 4-wire /8-wire mode, opened. 42 PANEL_THOa I/O Pen down detection pin. 43 PANEL_THI I In power-save mode, start signal input pin by pen down. 44 O Unused pin; Opened. 45 O Unused pin; Opened. 46 O Unused pin; Opened.
TSC-30/IC Product Specification 4. Initial setting 4-1. EEPROM setting Depending on that calibration is performed in either TSC-30/IC or host, you can select whether EEPROM is used or not to store the correction data. EEPROM selection can be set via pin number 50, where hardware reset release enables the setting. (TSC-30/IC) VCC (EEPROM) H= Not used EEP-CS/JP9 L= Used CS 4-2. Communication mode setting Communication mode setting for serial/USB is performed by setting pin number 37 to “H” or “L”.
TSC-30/IC Product Specification 4-4. Configuration in USB mode § Basic configuration Item Specification USB standard Specification Rev2.
TSC-30/IC Product Specification 5. Data sheet 5-1. Absolute maximum rating Item Power supply voltage Symbol Ratings Minimum Maximum Unit VCC -0.3 6.5 V Input voltage VI -0.3 Vcc+0.3 V Output voltage VO -0.3 Vcc+0.3 V Power consumption 500 mW Operation temperature TOPR -20 +85 ˚C Storage temperature TSTG -40 +125 ˚C Document No. DER-S0098A PD 9 Description Ta=25˚C Version 1.3 ©2012 DMC Co., Ltd.
TSC-30/IC Product Specification 5-2. Recommended operational conditions Limits Item Symbol Unit Minimum Standard Maximum 3.00 5.00 5.25 Power supply voltage Vcc Analog reference voltage AVcc Analog reference voltage AVREF Analog reference voltage USB USBVREF Power supply voltage Vss 0 V Analog reference voltage AVss 0 V “H” input voltage Vcc Description V V 2.0 Vcc V 3.0 3.6 V Vcc=3.6 to 4.0V 3.0 Vcc V Vcc=3.0 to 3.6V VIH 0.8Vcc Vcc V VIH 0.8Vcc Vcc V VIH 0.
TSC-30/IC Product Specification “L” output peak current *2 IOH (peak) 10 mA IOH (peak) 20 mA IOH (peak) 10 mA IOH (avg) -5 mA IOH (avg) -5 mA IOL (avg) 5 mA IOL (avg) 10 mA IOL (avg) 5 mA XIN 6.
TSC-30/IC Product Specification 5-3. Timing requirement § Reset (Vcc = 3.0 to 5.25V , Vss = 0V , Ta = -20 to 85°C) Item Symbol RESET L width tw Limits Minimum Maximum Unit Description μs 2 tw RESET 0.8Vcc 0.8Vcc 0.2Vcc 0.2Vcc § Power-on reset Reset input voltage shall be 0.6V or below at the timing when power supply voltage crosses 3.0V. (Ta = -20 to 85°C) (PWR ON) 3.0V Reset release voltage: Vcc = 3.0V VCC ≦0.2Vcc RESET Document No. DER-S0098A 12 Version 1.3 ©2012 DMC Co., Ltd.
TSC-30/IC Product Specification § External clock timing Item Symbol Input cycle Clock pulse width tC tWH, tWL Limits Minimum Maximum 166 70 Unit Description ns ns Clock Frequency Fixed to 6MHz tC tWH tWL 0.8VCC 0.2VCC XIN § Clock input circuit Using ceramic vibrator External clock input circuit CIN XIN XIN XOUT Open XOUT COUT Document No. DER-S0098A 13 Version 1.3 ©2012 DMC Co., Ltd.
TSC-30/IC Product Specification 5-4. DC standards (Vcc=3.00 to 5.25V, Vss=0V, Ta=-20 to 85˚C, unless otherwise noted) Limits Item Symbol Condition Unit Minimum IOH = -10mA “H” Output voltage (Pin number 16-19, 27-50) VOH VCC = 4.0 to 5.25V IOH = -1.0mA IOH = -10mA “H” Output voltage (Pin number 1-6, 51-64) “H” Output voltage (Pin number. 25 (D+), 26 (D-)) VOH VOH VCC = 4.0 to 5.25V IOH = -1mA Pull-down with 0V via a resistor of 15kΩ±5% Standard Vcc-2.0 V VCC-1.0 Vcc-2.0 Vcc-1.0 2.8 3.
TSC-30/IC Product Specification Normal Icc1 mode *1 Power supply current Icc2 3.0 to 4.0V Vcc= *2 3.0 to 5.25V suspend mode*3 2.1 Vcc= STOP mode At USB Icc3 Vcc= 4.0 to 5.25V Vcc= 4.0 to 5.25V Vcc= 3.0 to 5.25V 60 mA 35 mA 2.0 125.0 0.1 mA 250 uA uA *1: All USB difference-input circuits enabled. Leaving I/O pins open. Operating functions: CPU, Timers *2: All USB difference-input circuits enabled. Leaving I/O pins open. Operating functions: Timers, USB receiving.
TSC-30/IC Product Specification 6. Packaging Specification 6-1. Outline With a basic packaging unit of 800, TSC-30/IC is packaged for the number of 800 and its multiple using damp-proof aluminum laminate bags (Basic packaging). If the delivery quantity is less than 800 or not multiple of 800, or the product can not be packaged with a unit of 800, then no damp-proof packaging specification is applicable (Small group packaging). If packaged with small group packaging, the products may be dampened.
TSC-30/IC Product Specification 6-3-3. Diagram for packaging box sizes L: 351 W: 148 D: 55 (mm) 6-4. Small group packaging 6-4-1. Packaging type General packaging (No damp-proof processing) 6-4-2.
TSC-30/IC Product Specification 6-5. Tray specification This tray is heat-proof type, allowing the heating with 125 C for 24 hours. During heating/cooling process, however, bending may occur. In baking process, to minimize the bending, heat and cool the tray by placing it on a flat plate. 6-6. Product name label specification DMC P/N: Product number (TSC-30/IC) QTY: Quantity DAC: DMC Control Number Document No. DER-S0098A 18 Version 1.3 ©2012 DMC Co., Ltd.
TSC-30/IC Product Specification 7. Storage Specification 7-1. Storage Conditions For storing the product until its implementation, it is recommended that the following storage conditions are applied: 1. Before unpacking the damp-proof package (Aluminum laminate bag) Temperature and humidity: 5 to 40 C, 20 - 80%RH Duration: Two years or less 2.
TSC-30/IC Product Specification 8. Implementation Temperature Specification We do not recommend the wave soldering method. 1. Reflow method (Infrared reflow, air reflow) Frequency: Three times or less Temperature: The following device surface temperature profile is recommended. 260 C max. Package’s surface temperature 255 C or higher, 10s max. 220 C or higher, 50s max. 200 C or higher, 70s max. 17510 C 1 to 4 C/s 11020s Time Figure 1: Infrared reflow, air reflow temperature profile 2.
TSC-30/IC Product Specification 9. Terminal Pin Specification Base material :Cu Coat :Sn-1.5%Cu Thickness of coat :5um or above 10. Cleaning In case of cleaning boards with solvents after soldering, following items should be taken attention. *Administrative guidance and regulation. *Residual ionic (non ionic) contamination. *Solvent resistance of parts. Document No. DER-S0098A 21 Version 1.3 ©2012 DMC Co., Ltd.
TSC-30/IC Product Specification 11.Changes and improvements 11-1. Version history § TSC-30/IC Ver0.1 (July 31, 2007) Draft release Ver0.2 (September 27, 2007) 2. Pin layout Pin layout was changed. (SW0, SW1, LED0, LED2, RxD_I) 3. Pin functions Pin functions were changed. (LED0, LED2, USB_PW, EEP-DI/JP11, EEP-CLK/JP10, JP3, JP8) 4-2. Communication mode setting Terminal number was changed from 57 to 37. 4-5. Panel ID setting (USB mode) Replaced setting of JP4 with JP5. “6.
TSC-30/IC Product Specification Ver1.2 (November 10, 2010) 1-4. General specification Operation Temp: USB changed to -20 ˚C to +85 ˚C 3. Pin functions Pin No.36 (BEEP) “Output frequency=2.5KHz, Output time=50ms ” was added. Circuit Diagram Transistor number was added. (Rev2) Ver1.3 (May 25, 2012) Address has changed as Tokyo office had moved Document No. DER-S0098A 23 Version 1.3 ©2012 DMC Co., Ltd.
TSC-30/IC Product Specification 12. Warranty 12-1. Warranty Period § The warranty period is limited to 1 year from the date of shipping. The warranty for the initial defection such as appearance defection is limited to 1 month. § Any defected parts under proper use will be examined by the supplier and replaced by the new parts if the defection is considered to be caused by the supplier. § The replacement is subject to be included in the next lot. 12-2.
TSC-30/IC Product Specification 13. Notes on use 13-1. Overall handling § When using the product, do not place it close to, or make it contact with, the conductive materials such as metal. § Do not touch the metal part in the product directly with your hands. Or, it may be destructed by the static electricity. If you contact, or may contact, it directly with your hand, prepare in advance the measure against static electricity.
