Analog Resistive Touchscreen ATP/AST Series Product Specifications
ATP/AST Series Product Specifications Table of Contents 1. Product Specifications ...................................................................................................................... 3 1-1. Product Applicable ........................................................................................................................ 3 1-2. Structure ...................................................................................................................................... 3 1-3.
ATP/AST Series Product Specifications 1. Product Specifications 1-1. Product Applicable § This specification is applied to the analog resistive touchscreen: ATP/AST Series. 1-2. Structure § Dimensions, structure, and shape are referred on the drawing attached. 1-3. Environmental Specifications Specification Value Operating Temperature -20°C to 70°C (no condensation) Operating Humidity -20°C to 60°C Less than 90%RH (no condensation) 3 Exceeding 60°C 133.
ATP/AST Series Product Specifications 1-6. Appearance § Scratch, dust (W = width, L = length, D = average diameter = (longest + shortest) /2) Item Width (mm) Length (mm) Acceptable Numbers Linear(Scratch/Dust) Over 0.1mm in diameter refer to the Circular. 0.1W>0.05 4L 1pcs in 30mm 0.05W>0.03 10L 2pcs in 20mm 0.03W 20L Acceptable Circular (Scratch/Dust) 0.4D>0.3 *1 1pcs in viewing area *1 0.3D>0.2 2pcs in 30mm 0.
ATP/AST Series Product Specifications 2. Testing Regulation 2-1. Testing Regulation § If the regulation is not specified, the test is performed under the supplier’s regulation. § Tests are performed under the room temperature unless specified. The room temperature is referred as follows: Temperature: 20C5C Humidity: 65%10%RH 2-2. Environmental Specifications § Chemical Resistance Test Condition: Tested after leaving the chemical on the surface for 12 hours being wiped off by cloth.
ATP/AST Series Product Specifications 2-4. Electrical Characteristics § Terminal Resistance Test Condition: Top and bottom electrodes are measured at the terminal. Judgement: Must satisfy the specification. § Insulation Resistance Test Neighboring Terminals: Measured by applying the reference voltage to the terminals Active Area Electrodes: Measured by applying the reference voltage to the top and bottom electrodes. Judgement: Must satisfy the specification. 2-5.
ATP/AST Series Product Specifications 3. Reliability Condition 3-1. Temperature Condition § Temperature Condition Test Following test are performed in the condition with no dew condensation: Cold Test: Tested after leaving the parts in -40°C3°C for 240 hours and in the room temperature for 2 hours. Heat Test: Tested after leaving the parts in 80°C3°C for 240 hours and in the room temperature for 2 hours.
ATP/AST Series Product Specifications 5. Handling Notes 5-1. Precautions § This product is intended for use in standard applications (computers, office automation, and other office equipment, industrial, communications, and measurement equipment, personal and household devices, etc.
ATP/AST Series Product Specifications 5-5. Mounting Notes Bezel § Bezel Edge Bezel edge must be positioned in the area between the Active Area and the Viewing Area. The bezel may press the touchscreen and cause input if the edge enters the Active Area. Bezel Top Electrode A gap of approximately 0.5mm is needed between the bezel and the top electrode. It may cause unexpected input if the gap is too narrow. 0.
ATP/AST Series Product Specifications 6. Warranty 6-1. Warranty Period § The warranty period is limited to 1 year from the date of shipping. The warranty for the initial defection such as appearance defection is limited to 1 month. § Any defected parts under proper use will be examined by the supplier and replaced by the new parts if the defection is considered to be caused by the supplier. § The replacement is subject to be included in the next lot. 6-2.
ATP/AST Series Product Specifications 7. Revision History Rev1 (April 15, 1998) Initial release Rev2 (June 1, 1999) The overall revision by specification review. Rev3 (April 1, 2002) The address in the office was changed by the move. Rev4 (August 16, 2002) 1-4.Activation Force is changed “50g 30g” to “0.5N0.3”. 1-4.Light Transmission is changed 76% to 80%(TYP). Rev5 (September 3, 2002) 1-3.Operating Temperature is changed “0°C to 60°C” to “-20°C to 70°C”. 1-3.
ATP/AST Series Product Specifications Rev10 (November 10, 2006) The specification item name was changed. 1-3.”Storing Temperature” to “Storage Temperature” 1-3.”Storing Humidity” to “Storage Humidity” 1-4.”Operating Load” to “Activation Force” 1-4.”Light Transmissivity” to “Light Transmittance” 1-4.”Top Surface Hardness” to “Surface Hardness” 2-3.”Operating Load Test” to “Activation Force Test” 2-3.”Operating Load” to “Activation Force” 3-1.”Operationg Load” to “Activation Force” 1-4.
ATP/AST Series Product Specifications Rev13 (Feb 13, 2013) 1-6. Appearance Tip → Chip (Scribal error corrected) 5-2. Handling Notes ・Do not depress or scratch the product with any object with a sharp edge or end. → Do not depress or scratch the product with any object with a sharp edge or hard end. (Description changed) ・Do not put this product close to fire. (Description added) ・Do not wipe this product with too much load. (Description added) ・Do not strongly rub this product locally.
