User Manual

ManualsBrandsDM Technology ManualsElectronicsDigital presentation device

Cover

17” WIDE TFT LCD TV

Before using this product, please read the security instructions first and bear them

in mind when using the product.

Security Instructions

To prevent damage, which may result in fire or electric shock hazard, do not expose this

appliance to rain or moisture.

This product has been designed and manufactured for home and office use.

Any problems with the TV will not be valid for the service agreement when the product

has been used for purposes other than home or office use, even if the warranty period has

not expired.

This product is manufactured and sold for domestic use only.

The company shall not be held liable for any malfunction of the TV, if it is used anywhere

else except the domestic market.

Additionally, TV support can only be provided for the domestic market.

Safety Instructions

Warning! Important

Safety Instructions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is

dangerous to make any kind of contact with any inside part of

this product.

This symbol alerts you that important literature concerning

operation and maintenance has been included with this product.

Note to CATV system installer: This reminder is provided to call CATV system

installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of

Canadian Electrical Code, Part I), that provides guidelines for proper grounding

and, in particular, specifies that the cable ground shall be connected to the

grounding system of the building as close to the point of cable entry as practical.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications

to this equipment may void the user’s authority to operate it.

Summary of content (43 pages)

PAGE 1
Cover 17” WIDE TFT LCD TV Before using this product, please read the security instructions first and bear them in mind when using the product. Security Instructions To prevent damage, which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. This product has been designed and manufactured for home and office use.
PAGE 2
Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug. Attention: pour eviter les chocs electriques, introduire la lame le plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U.S. copyright laws.
PAGE 3
• Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal. • Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.
PAGE 4
P FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 5
convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6015P type (tandem blades) plug cap. IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003.
PAGE 6
should take into account the following conditions. - They have to comply with VESA Mount Interface 100mm standard. - They have to able to sustain the weight of the LCD TV. - They have to be fixed to a position adjustable by hand. - They have to be adjustable. - The distance between the screw holes for fixing the arms has to be 100mm. Additionally, refer to the installation manual supplied with the arms for installation. Arm installation procedures Install the arms following the procedure s given below. 1.
PAGE 7
Alkaline detergent, alcohol-detergent, liquid compound, powdered compound, car wax, etc. ?Maintenance of the LCD Panel ?To clean the dust on the LCD panel, lightly clean the surface of the panel with a soft dry cloth. If the stain on the surface of the LCD panel does not come off easily, spray an LCD panel cleansing solution on the surface, and clean the surface with a soft cloth again. While doing his, take care not to spill the solution so as to prevent the solution from entering the inside of the panel.
PAGE 8
Remote Control & Battery (1.5V AAA) AC adapter RF Connection Cables Power Cord Owner’s Instructions Video/Voice Connection Cables 10P Before Using the TV Rear Panel Jacks 1. POWER INPUT CONNECTOR: Only connect with the AC adapter DC 12V/5A supplied with this product. 2. PC INPUT JACK: Used to connect to a PC. 3. PC AUDIO INPUT JACK: Used to connect to a PC. 4. COMPONENT VIDEO INPUT JACK: Used to connect to a DVD player or a DTV receiver. 5.
PAGE 9
6. NUMBER BUTTONS: Selects channels directly on the TV. 7. 100: Selects channels over 100. For example, to select channel 121, press “+100,” then press “2” and “1.” 8. PRE: Moves to the previous channel. 9. MENU: Displays the OSD menu. 10. PICTURE: Configures various video modes. 11. SOUND: Configures various sound modes. 12. VOLUME (-/+): Increases or decreases the volume. 13. CHANNEL (?/?): Changes channels . 14. ASPEC: Changes the screen size. 15. EXIT: Cancels the current configuration. 16.
PAGE 10
The remote control works up to about 7~10m from the TV, 3m to the left or right of the TV, and to within 30 degrees from the remote control sensor of the TV. The remote control does not work properly! Check! 1. Are the polarities of the installed batteries correct? 2. Has the battery discharged completely? 3. Is the power cord plugged in properly or is there a power failure? 4.
PAGE 11
?If your VCR does not support stereo sound, connect the mono audio out jack to the AUDIO INPUT (left) jack. Procedures for watching a video over a VCR 1. Turn the TV on, and select 'VIDEO' using the TV/VIDEO button on the remote control. ?If you have connected a S-VIDEO cable, select 'SVHS'. 2. Turn the VCR on, insert the tape, and press the Play button. 15P Connections Connecting the Antenna Input Jack Connection Procedures 1. Connect the antenna cable to the ANTENNA IN terminal on the back of the VCR.
PAGE 12
output jack of your DTV receiver with the component video connectors (Y.Pb, and Pr). 2. Connect the left and right COMPONENT AUDIO INPUT jacks of the TV to the component audio output jack of the DTV receiver using the audio cables. Procedures to Watch DTV 1. Turn the TV on and select 'DTV' using the TV/VIDEO button on the remote control. 2. Turn the DTV receiver on and select the desired channel. 17P Connections Connecting an STB Receiver Connection Procedures 1.
PAGE 13
cableTV receiver using the video/audio cables. (Connect the cable to the terminal of the same color). Procedures to Watch Cable TV 1. Turn the TV on, and select 'VIDEO' using the TV/VIDEO button on the remote control. 2. Turn the cable TV receiver on and select the desired channel using the remote control of the receiver. 19P Connections Connecting the Antenna Input Jack Connection Procedures 1. Connect the cableTV antenna cable to the ANTENNA IN jack on the back of the cable TV receiver. 2.
PAGE 14
3. Are the remote control batteries installed properly? 4. Have the receive channels been configured? 5. Are the cables connected to any external devices connected properly? 21P Procedures for Using the TV Watching TV Turning the TV On and OFF Turn the power switch on the front panel of the unit downward to turn on the unit. ?When you turn the power「ON」, the screen appears and the POWER/STANDBY light is turned off.
PAGE 15
Press the DISPLAY button on the remote control. The TV will display the input source, the picture mode, the sound mode, the mts mode, the current time, the v-chip and the audio signal you are lis tening to. Adjusting the Volume ?Adjust the volume using the 「-VOL/VOL+」button. Muting the Sound ?Press the「MUTE」button. You can conveniently use the MUTE button when a telephone or a door bell rings. To cancel, press the MUTE button again. Viewing a Video or DVD ?Press the「TV/VIDEO」button.
PAGE 16
4. Select AIR, STD, HRC, or IRC using the 「CHANNEL?/? 」button. If you are not sure which type of cable system you have, contact your cable company. Note: STD, HRC and IRC represent various types of cable TV systems. 24P Procedures for Using the TV Storing Channels in Memory (Automatic Method) The TV automatically runs through all available channels and stores them to memory. This takes approximately one or two minutes. 1. First, select the correct signal source (AIR, STD, HRC, IRC).
PAGE 17
The MENU will be displayed. 2. Select CHANNEL SETUP using the 「CHANNEL? /?」button and then press the 「VOL+」button. 3. Select ADD/ERASE using the 「CHANNEL? /?」button and then press the 「VOL+」button. Adding a channel 4. Select a channel to add using the 「CHANNEL? /?」button and then press the 「VOL+」button. The OSD changes from ADD to – -- . Deleting a channel 5. Select a channel to delete using the「CHANNEL?/? 」button and then press the 「VOL+」button. The OSD changes from – to ADD. Complete steps 4~5.
PAGE 18
Example : For channel 122, press ” 100 ”,then ”2 ”,then ” 2 ”. Using the Previous Channel Press the 「 PRE」button on the remote control. The TV vhanged to the last channels to the last channel you were watching.. 27P Operation When the Picture Quality is poor or Unstable Use fine tuning to adjust a particular channel for better picture quality when no ise interferes, color quality is poor, or the screen is unstable. 1. Select the channel to tune using the numeric or channel buttons. 2.
PAGE 19
1.Press the 「MENU」button. The MENU will be displayed. 2. Select CHANNEL SETUP using the「CHANNEL? /?」button and then press the 「VOL+」button. 3. Select LNA using the 「CHANNEL? /?」button and then press the 「VOL+」button. 4. Select ON using the 「 CHANNEL?/? 」 button. 5. Press the 「 EXIT」 button to exit the menu . 29P Operation Selecting the Video Mode You can select a video mode from among USER, STANDARD, DYNAMIC, or MILD mode according to your personal preference. Press the PICTURE button.
PAGE 20
MILD USER : Select this mode when viewing the TV when the light is low. This mode lessens eye strain. : Select this mode if you want to adjust the settings according to your personal preferences. (For procedures to customize the picture, refer to page 27.) 30P Operation Adjusting Manually 1.Press the 「MENU」button. The OSD MENU will be displayed. 2. Select PICTURE SETUP using the「 CHANNEL?/? 」 button and then press the 「VOL+」button. 3.
PAGE 21
31P Operation Selecting the Sound Mode You can select the sound mode from among USER, STANDARD, MUSIC, or SPEECH mode according to your personal preference. Pressing the SOUND button. Whenever you press this button, the video menu changes to USER ? STANDARD ? MUSIC? SPEECH mode, in this order. 1.Press the 「MENU」button. The OSD MENU will be displayed. 2. Select SOUND SETUP using the「CHANNEL?/? 」button and then press the 「VOL+」button. 3. Select the desired SOUND MODE using the 「CHANNEL? /?」button.
PAGE 22
3. Select BALANCE using the「CHANNEL? /? 」button and then press the 「 VOL+」 button. 4. Select the desired status using the 「-VOL」and 「VOL+」button. During the adjustment, an additional adjustment window will be displayed. The adjustment window disappears and changes are applied when 3 seconds have elapsed after the last input. Also, the SOUND MODE is automatically changed to USER mode. ?BALANCE: Determines the volume ratio between the left and right speakers. 5. Press the「EXIT」button to exit the menu.
PAGE 23
33P Choosing a Multi-Channel Sound (MTS) Soundtrack Depending on the particular program being broadcast, you can listen to Stereo, Mono, or a Separate Audio Program. (SAP audio is usually a foreign language translation. Sometimes SAP has unrelated information like news or weather.) ?Pressing the 「MTS」button. Whenever you press this button, the mode changes to STEREO ? MONO? SAP mode, in this order. 1.Press the 「MENU」button. The OSD MENU will be displayed. 2.
PAGE 24
NORMAL → ZOOM → PANORAMA, in this order. (Note that you can select either WIDE or NORMAL mode in PC input mode.) Screen Size Menu ?WIDE mode Set the picture to 16:9 wide mode. ? NORMAL mode Sets the picture to 4:3 normal mode. This is a standard TV screen size. ?ZOOM Mode Magnifies the size of the picture on the screen. ?PANORAMA mode Use this mode for the wide aspect ratio of a panoramic pict ure. ?Note You can select only WIDE, NORMAL(4:3) screen size in the Component and PC Mode.
PAGE 25
The PIP SETUP menu will be displayed. 4. Select PIP ON/OFF using the 「CHANNEL? /?」button and then press the 「VOL+」button. Select ON using the「CHANNEL?/? 」button. Whenever you press this button, PIP mode is turned either on or off. Selecting OFF turns off PIP mode. 5. Press the「EXIT」button to exit the menu. Note ?Since this product has a single tuner, you cannot watch two TV channels simultaneusly in PIP mode. ?You can only listen to one sound output from either the main screen or the PIP window.
PAGE 26
(TV->VIDEO->SVHS->DTV) 5. Press the「EXIT」button to exit the menu. ?Since this product has a single tuner, you cannot watch two TV channels simultaneusly in PIP mode. 37P Operation Changing the PIP Window Channel When the PIP window shows normal broadcasting (TV and CATV) channels, you can change the PIP window channel. ?Press the 「CHANNEL?/? 」button in the PIP function. Whenever you press this button, the channel is changed. 1.Press the 「MENU」button. The OSD MENU will be displayed. 2.
PAGE 27
38P Operation Selecting Audio in the PIP Screen Mode You can select the desired audio source from either the main screen, or the PIP window. ?Pressing the 「SOUND」button. Whenever you press this button, the mode is changed to MAIN ? SUB. When MAIN is selected: Audio of the main screen is heard. When SUB is selected: Audio of the PIP screen is heard. Swapping the Main and the PIP Window You can swap the video source of the main screen and the PIP window. ?Pressing the SWAP button.
PAGE 28
The OSD MENU will be displayed. 2. Select FUNCTION SETUP using the「CHANNEL ? /? 」button and then press the 「VOL+」button. 3. Select PIP SETUP using the「CHANNEL?/? 」button and then press the 「VOL+」button. The PIP SETUP menu will be displayed. 4. Select PIP BORDER using the 「CHANNEL ? /? 」buttons and then press the「VOL+」button. Select the BORDER color using the「CHANNEL?/?」button. Whenever you press this button, the PIP window border color is changed to GRAY ? BLACK? MAGENTA? CYAN? OFF, in this order. 5.
PAGE 29
41P Operation Setting the Clock Setting the clock is neccessary for using the various timer features of the TV. 1. Press the 「MENU」button. The OSD MENU will be displayed. 2. Select FUNCTION SETUP using the 「CHANNEL ? /? 」button and then press the 「VOL+」button. 3. Select TIME SETUP using the 「CHANNEL? /?」button and then press the 「VOL+」button. The TIME SETUP OSD will be displayed. 4. Move to the Hour using the「VOL+」button and then set the Hour to the correct time using the 「CHANNEL? /?」button. 5.
PAGE 30
The TIME SETUP OSD will be displayed. 4. Move to TIMER using the 「CHANNEL ? /? 」button and then press the 「VOL+」button. Select ON using the「CHANNEL? /? 」button. The ON/OFF TIMER works only when the timer is configured to ON. 5. Press the 「VOL+」button. Move to ON TIME/ OFF TIME using the 「CHANNEL? /?」button. 43P Operation ?Turning On At 6:10 AM 1. Move to the Hours using the 「VOL+」button and then set the Hour to 6 AM using the 「CHANNEL? /?」button. 2.
PAGE 31
Operation Selecting the ON Timer Channel / Adjusting the ON Timer Volume You can configure the channel and volume to play when the TV is turned on by the Timer. 1.Press the 「MENU」button. The OSD MENU will be displayed. 2.Select FUNCTION SETUP using the 「CHANNEL? /?」button and then press the 「VOL+」button. 3. Select TIME SETUP using the「CHANNEL? /?」button and then press the 「VOL+」button. The TIME SETUP OSD will be displayed. 4. Select CHANNEL using the「CHANNEL ?/? 」button and then press the 「VOL+」button.
PAGE 32
1.Press the 「MENU」button. The OSD MENU will be displayed. 2. Select FUNCTION SETUP using the「CHANNEL ? /? 」button and then press the 「VOL+」button. 3. Select TIME SETUP using the 「CHANNEL? /?」button and then press the 「VOL+」button. The TIME SETUP OSD will be displayed. 4. Select SLEEP using the「CHANNEL?/? 」button and then press the 「VOL+」button. Configure the SLEEP time using the 「CHANNEL?/? 」button.
PAGE 33
47P Operation MELODY Function If the MELODY function is turned on, a melody plays whenever the TV is turned on or off. 1.Press the 「MENU」button. The OSD MENU will be displayed. 2. Select FUNCTION SETUP using the 「CHANNEL ? /? 」button and then press the 「VOL+」button. 3. Select MELODY using the 「CHANNEL? /?」button and then press the 「VOL+」button. Select ON using the 「CHANNEL? /?」button. Whenever you press this button, the Melody function is turned either on or off. 4.
PAGE 34
Note After resetting, the screen goes blank and then displays a picture. 49P Operation Connecting to a PC Connection Procedures 1. Connect the PC D-SUB INPUT jack of the TV and the monitor output jack of the PC using the D-Sub cable. 2. Connect the PC AUDIO jack of the TV and the audio output jack of the PC with the audio cable. (This can only be applied when the PC actually has an audio output jack.) Procedures for viewing the PC screen through the TV 1.
PAGE 35
1. In WINDOW98/ ME/ 2000/XP, select Start-> Control Panel 2. Click the mouse ->Select Display Properties. 2 Select Display in Step 1. 3 The Display Properties window will be displayed. 1. Set the Screen resolution to 1280 by 768 pixels. 2. Set the Color quality to one of 16 bit, 24 bit, or 32 bit. Note . A screen resolution of WXGA(1280 X 768) provides the best screen quality. . Configure the screen color to 16-bit, or 24-bit. .
PAGE 36
4. Press the「EXIT」button to exit the menu. 52P Operation ?Adjusting the Phase 1.Press the 「MENU」button. The OSD MENU will be displayed. 2. Select PC SETUP using the 「CHANNEL?/? 」buttons and then press the「VOL+」button. 3. Select PHASE using the 「CHANNEL? /?」button and then adjust the phase using the 「VOL+」button. During the adjustment, an additional adjustment window will be displayed. 4. Press the「EXIT」button to exit the menu.
PAGE 37
3. Select H_POSITION using the 「CHANNEL?/? 」buttons and adjust the horizontal position using the「VOL+」button. During the adjustment, an additional adjustment window will be displayed. 4. Press the「EXIT」button to exit the menu. 54P Operation ?Adjusting the Vertical Position 1.Press the 「MENU」button. The OSD MENU will be displayed. 2. Select PC SETUP using the 「CHANNEL?/? 」buttons and then press the「VOL+」button. 3.
PAGE 38
4. Press the「EXIT」button to exit the menu. 56P Operation Auto Set You can adjust the frequency and the phase of the PC screen automatically. 1. Press the 「MENU」button. The OSD MENU will be displayed. 2. Select PC SETUP using the 「CHANNEL?/? 」buttons and then press the「VOL+」button. 3. Select AUTOSET using the 「CHANNEL?/? 」button and then select using the 「VOL+」button. The PC screen is adjusted automatically. 4. Press the「EXIT」button to exit the menu.
PAGE 39
The TV is turned on, The brightness is but there is no picture adjusted too low. on the screen. The fluorescent tube is out of order. An afterimage is generated when continuously watching a still image. No picture on the screen. No audio. A picture is displayed on the screen, but there is no audio. Remote control malfunctions. Adjust the brightness and the contrast so that a picture is displayed brightly. The fluorescent tube of a LCD TV has a lifetime of about 50,000 hours.
PAGE 40
Blurred or snowy picture. buildings, or trees near your house. The direction of the antenna is not optimal. The antenna cable is disconnected. Check that the direction of the antenna is correct. Check that the antenna cable is connected to the ANTENNA jack on the back of the LCD TV. 58P First try the following list of possible problems and solutions . If the symptom continues, turn the TV off, and call your nearest service center.
PAGE 41
59P Specifications The exterior design and the product specifications are subject to be changed without prior notice due to improvements in performance. This product is manufactured for domestic use. This product may not be used in countries whose television system type or power voltage is different.
PAGE 42
Color Quality 16,772,216 color Maximum Resolution 1280 X 768 Separation Signal TTL, Anode or Cathode Audio Out Power Supply Power Consumption Power Consumption When Power Saving Mode Dimension with Speaker/Monitor 5W x 2 / 5W x 2 (2 Way) AC 120V,50/60Hz, DC12V/5A Maximum 160W Less than 3W Weight Accessories 7.9 Kg Remote control, Battery (AAA), Owner’s Instructions, Power Cord, AC adapter, RF -Cables, Video/Voice Connectors. This device has been registered in regards to EMI for residential use.
PAGE 43
PIP Screen Configuration Table 61P Warranty Back Cover DMTECH Translation Request