User's Manual

ManualsBrandsDLP Design ManualsElectronicsRFID Tag Reader

DLP-RFID-LP8C

FEATURES:

• ISO 15693, 18000-3, Tag-it™ HF-I Compatible

• Read the UID/SID of Up To 15 Tags Simultaneously

• 13.56MHz Reader/Writer

• 8 channels for external antenna connections

• FCC/IC/CE Modular Approvals Pending

• USB Port Powered from Windows, CE, or Linux PC

• Optional RS232 Interface

• USB Interface; No Driver Development Required for Windows, CE, or Linux PC

• Operating Temperatures: 0°C to 70°C

• Dimensions: (L x W x H) 4.36” x 3.32” x .6”

APPLICATIONS:

• Real-Time Security

• Personal Identification

• Pharmaceutical Tracking

• Inventory/Asset Management & Tracking

• Library/Book Management & Tracking

• Baggage Tagging

• Sports Event Timing

1.0 INTRODUCTION

The DLP-RFID-LP8C is a low-cost, USB-powered

module for reading from and writing to ISO

15693, ISO 18000-3, and

Tag-it™ intelligent RFID transponder tags via up

to 8 external antennas. It has the ability to both

read and write up to 256 bytes of data in addition

to reading the unique identifier (UID/SID). All of

the DLP-RFID-LP8C’s electronics reside on a single compact PCB, and all operational power is

taken from the host Windows/Windows CE/Linux PC via the USB interface. Up to 8 external

antennas can be connected via standard SMA connectors.

2.0 APPLICATION DEVELOPMENT

Demonstration source code written in Visual C++ is available (upon purchase) that

demonstrates the communications protocol. Using the Virtual COM Port USB drivers, the DLP-

RFID-LP8C appears to the host PC (Windows, Linux, Mac) as an RS232 port.

Summary of content (4 pages)

PAGE 1
DLP-RFID-LP8C FEATURES: • • • • • • • • • • ISO 15693, 18000-3, Tag-it™ HF-I Compatible Read the UID/SID of Up To 15 Tags Simultaneously 13.56MHz Reader/Writer 8 channels for external antenna connections FCC/IC/CE Modular Approvals Pending USB Port Powered from Windows, CE, or Linux PC Optional RS232 Interface USB Interface; No Driver Development Required for Windows, CE, or Linux PC Operating Temperatures: 0°C to 70°C Dimensions: (L x W x H) 4.36” x 3.32” x .
PAGE 2
3.0 REGULATORY AGENCY CONSIDERATIONS 3.1 AGENCY IDENTIFICATION NUMBERS Compliance with the appropriate regulatory agencies is essential in the deployment of all transceiver devices. DLP Design is in the process of obtaining modular approval for this RF product such that an OEM need only meet a few basic requirements in order to utilize their end product under this approval. Corresponding agency identification numbers are listed below: Part Number US/FCC CAN/IC DLP-RFIDLP8C SX90LP8C 5675A-0LP8C 3.
PAGE 3
This device is intended for use under the following conditions: 1. The transmitter module may not be co-located with any other transmitter or antenna. 2. The module is approved using the FCC “unlicensed modular transmitter approval” method. As long as these two conditions are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance measures necessitated by the installation of this module (i.e.
PAGE 4
This product and its documentation are supplied on an as-is basis, and no warranty as to their suitability for any particular purpose is either made or implied. DLP Design will not accept any claim for damages whatsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device, or system in which the failure of the product might reasonably be expected to result in personal injury.