Specifications

Copyright Peek Traffic Systems Incorporated, 2000
27
OUTPUT MAPPING CONTINUED...
ADVANCE WARNING OUTPUT FUNCTIONS FOR PHASES & O/L’s
FUNCT
ADW1 ADW2 ADW3 ADW4 ADW5 ADW6 ADW7 ADW8
PIN #
FUNCT
ADWA ADWB ADWC ADWD
PIN #
SPECIAL FUNCTION BIT 1-16 OUTPUTS Note: Activated remotely via sys
FUNCT SF1 SF2 SF3 SF4 SF5 SF6 SF7 SF8
PIN #
FUNCT
SF9 SF10 SF11 SF12 SF13 SF14 SF15 SF16
PIN #
SPEC 17-24, Contrast bits, Backlight bit, CVM/Fault Monitor Inhibits
FUNCT
SF17 SF18 SF19 SF20 SF21 SF22 SF23 SF24
PIN #
FUNCT
CNT0 CNT1 CNT2 CNT3 EL CVMI FMI
PIN #
DETECTOR SIMULATOR OUTPUT FUNCTIONS
FUNCT
DS01 DS02 DS03 DS04 DS05 DS06 DS07 DS08
PIN #
FUNCT
DS09 DS10 DS11 DS12 DS13 DS14 DS15 DS16
PIN #
PRE-EMPT ACKNOWLEDGE OUPTUTS 1-6
FUNCT
PEA1 PEA2 PEA3 PEA4 PEA5 PEA6
PIN #
CHANNEL 1-8 RED, YELLOW GREEN OUTPUTS
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
RED CH #
YEL CH #
GRN CH #
CHANNEL 9-16 RED, YELLOW GREEN OUTPUTS
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
RED CH #
YEL CH #
GRN CH #
INPUT FUNCTIONS DEFINTIONS
ABBREV BRIEF COMMENT/DESCRIPTION
VD1-24 Vehicle Detector inputs 1-24 (see detectors/options)
VD25-32 Vehicle Detector inputs 25-32. Not currently supported by controller
PED1-8 Phase 1-8 pedestrian call inputs
HLD1-8 Holds Phases 1-8 at end of green (TDB pg 2-19)
VOM1-8 Omits (skips) phases 1-8
POM1-8 Omits peds for phases 1-8 (ph can still be served)
PRE1-6 Call pre-empt sequences 1-6 (allowing delay B4 PE)
WRM Allows CNA phase to rest in walk after hold released
MRCL Recall all phases, serves at least minimum green
SQCS Phase stays gapped out/second service on left turns
WP10 Overrides normal week prog, goes to week prog. 10
ASQA-D Alt sequence or “Lead/lag.” A=reverse 1&2, B=3&4, C=5&6, D=7&8
MCE Put calls on all phases, stops time except Yel & Red
IADV Toggle advances to next interval, used w/MCE
EXST Takes controller immediately to initialization interval
TSTA Used in LMD controllers for DC remote flash (UCF)
TSTB Programmable (controller options) Dim or Call free
TSTC New TS2 test input, no defined function
DIM Dimming by phase in color (see controller options)
LAMP No function in LMD controllers due to LC displays
MONA-C Receives 3 status bits from LSM or LNM monitors
MONF Flash Receives MMU flash status from MMU
LCLF Receives local flash status from switch, relay, etc.
FLM1/2 Monitors 2 flasher ckts, records alarm and/or calls in
PLNA-D Implements timing plans 1-16 In cyc/spl terms; A=cyc2, B=Cyc3, etc.