Spreading Wings S800 EVO User Manual V 1.10 February 07, 2014 Revision www.dji.
Disclaimer Thank you for purchasing this DJI product. Please regularly visit the S800 EVO web page at www.dji.com, which is updated regularly. Product information, technical updates and manual corrections will be available on this web page. Due to unforeseen changes or product upgrades, the information contained in the manual is subject to change without notice. Read this disclaimer carefully before using this product.
Profile S800 EVO is a multi-rotor designed for aerial photograph which integrates reinforced mechanical structures, stabilized dynamical system and high-efficiency power supply. Integrated designs make assembly and configuration become especially easy and fast; retractable landing gear, foldable propellers and collapsible GPS Mount are conveniently portable for optimal user experiences.
Contents Disclaimer................................................................................................................................................................................................................ 2 Profile ....................................................................................................................................................................................................................... 3 Contents................................................
Product Usage Cautions When flying, the fast rotating propellers may cause serious damage(s) and injuries. Therefore, please fly with a high safety in mind at all time. Assembly Cautions (1) Mount the GPS Module with a bracket, to avoid interference with the power board of center frame. (2) For IMU mounting, make sure the arrow direction marking on the IMU is pointing to the aircraft nose.
In The Box Center Frame×1 Frame Arm×6 Retracting Mechanism×2 Landing Gear Support Tube ×2 Base Pipe×2 H Frame Connection Pipe×1、Spring×2 Package of 3-PIN Servo Cable ×1 Silicone Rubber Damper ×4 Package of Battery Tray×1 Package of IMU Mount×1 GPS Fixed Seat×1 Screw Package for Frame×1 Screw Package for Landing Gear×1 Out of The Box Guidance ×2 Tools Needed 2.0mm Hex Wrench, 2.5mm Hex Wrench For mounting screws. Thread Locker For fastening screws.
Center Frame Wiring The top board is a power distribution board, and the bottom board is for loading autopilot system components.
Attach Electric Equipment to Center Frame 1. (Fig.1)Remove the screws in the bottom board. 2. (Fig.2)Attach the IMU module into IMU position in the center frame. Ensure the IMU casing is out of touching the top board edge, as vibration can cause IMU mal-function. 3. (Fig.2)Please attach DJI Autopilot System parts onto the bottom board (not including GPS modules. 4. (Fig.2)Connect the Autopilot System and receiver. Please refer to DJI WKM User Manual for details. 5. (Fig.
Fig.3 Fix the screws Note: for DJI A2 user, please use the component in red; for WKM user, it is not required. Fig.4 Mount the GPS Fixed Seat and GPS module Mind You Fingers Fig.
Mount Frame Arms Step 1 Step 2 Copper contacts Propeller Screw Cover Motor Motor rotation direction (1) Clock-wise ESC Counter clock-wise LED Step 3 Step 4 Step 5 Vertical 35o Horizontal Horizontal (2) Step1: Check the arms. (1) Make sure the copper contacts are in good condition without bend or severe wear. (2) Make sure the propellers are without crack, and screws in propeller cover tight. (3) Make sure the motors are mounted firmly, and rotate freely.
(3) Please refer to (2) to make sure the arm is perfectly positioned. (4) Make sure to use appropriate strength to press down the buckle correctly. (5) Do not hot plug arms. Tips: (1) LED is on after motor start. Step 6 Double Check Arms①②are aircraft nose, arms④⑤ are aircraft tail. See from top, motors on arms①③⑤ rotate counter clockwise; motors on arms②④⑥ rotate clockwise.
Mount Landing Gear By using a 2-position switch of R/C transmitter, you can control the landing gear to retract remotely. 1 Assembly & Connection The part with the control board attached is defined as left, and the other part is right. Make sure to make a distinction between the left and the right servos.
1. Assemble the left and right parts respectively, and then fix the screws at the joints with appropriate thread locker. 2. Connect the left and right parts with connecting rod. 3. For safety reasons, make sure to connect the springs to both parts. step3: 1. Electrical Connections Plug the cables from the servos into the correct ports on the control board. Make sure the right servo is connected to the [R] port, and the left servo to the [L] port. 2.
3 Transmitter Setting Select a 2-position switch (default setting is OK) of Transmitter as the control input of the landing gear, and then make sure the corresponding port of receiver is connected to the [IN] port on control board. Retracted:Toggle the switch to Fig. 1 this position to retract the landing gear (Fig.1) Lower:Toggle the switch to this position to lower the landing gear (Fig.
Tips (1) The system will turn off the servo power temporarily within 3 seconds after the landing gear has reached the target position. (2) When powering on the system, if the Transmitter switch is at the [Retracted] position, which is the unsafe signal for the landing gear, the LED will quickly flash RED. Toggle the switch to the [Lower] position. (3) If there is an abnormal signal or no signal input into the [IN] port the LED will slowly flash RED. Please check the receiver and the connections.
5 Mount Battery Bracket Step1: Mount the retaining clip and the bracket, fix screws (but not tighten). M2.5X5 Bracket Notch Outwards Retaining Clips Chamfer Outwards Step2: Place the battery mounting board and adjust its position, and then tighten all screws.
Assembly Assembly ② ③ ft cr a A ir ose N ① ④ ⑥ ⑤ Align knob to mark Insert knob into arm Rotate knob (2) (1) Knob Mark Vibration Absorber Vibration Damper Mount Vibration Damper Mount Details Coaxial Align Not Coaxial Not Coaxial 1. Align all knobs on H frame to the marks; refer to fig (1). 2. Lie frame and Landing Gear horizontally, insert knobs into arms ③ and ⑥ first, and then adjust to insert the others into the arms. 3.
Install the IMU Mount (Optional) If you wish to achieve a smooth and steady fight, carry out the following procedures to install the IMU Mount. 1. (Fig.1) Remove the screws to dismount the Battery Bracket. 2. (Fig.2) Fix the IMU Mount and remount the Battery Bracket. 3. (Fig.3) Adjust the IMU Mount and the Battery Bracket, and then fix all the screws. 4. (Fig.4) Attach the IMU Module; make sure that the arrow on LOGO is pointing to the aircraft nose. Fig.1 Fig.
Appendix ESC Sound ESC State Sound Ready ♪1234567--B--B Throttle stick is not at bottom BBBBBB… Input signal abnormal B--------B--------B… Input voltage abnormal BB---BB---BB---BB… ESC LED ESC State LED Standby Off Motor rotating Solid Red or Green On Motor rotating at full throttle position Solid Yellow On Tips: DJI ESCs are specially designed for multi-rotors. When use with DJI autopilot systems, you do not have to setup any parameters or calibrate travel range.
Specifications Frame Diagonal Wheelbase 800mm Frame Arm Length 350mm Frame Arm Weight (with Motor, ESC, Propeller ) 356g Center Frame Diameter 240mm Center Frame Weight 550g Landing Gear Size Retractable Landing Gear Weight (Including Battery Tray) 460mm(Length)×425mm(Width)×320mm(Height) (Top width: 155mm) 1050g Motor Stator Size 41×14mm KV 400rpm/V Max Power 500W Weight (with Cooling Fan) 158g ESC Current 40A OPTO Voltage 6S LiPo Signal Frequency 30Hz ~ 450Hz Drive PWM Frequency
FAQ (Trouble Shooting) Solder ESC Make sure to solder the thick wires and fine wires correctly, when solder ESC to frame arm. Clockwise and counter clockwise motor should be soldered to ESC correctly by different color order.
Spare Parts Listing If S800 EVO needs component replaced, please refer to the following diagram to identify the component NO., and then make a purchase of corresponding package. Each package includes screws needed. The Components Number is defined as bellow. S800 EVO 01Arm Frame;02Center Frame; 03Landing Gear SE010101CCW CW-Clockwise;CCW-Counter clockwise; Package NO. ; Parts NO. ; Frame Arm M3x10.5(2pcs) M3x4.
Center Frame M2x9(12pcs) SE021401(6pcs) M2.5x5(25pcs) SE021201 SE021601(7pcs) SE021501 SE021502 SE021503 SE021301 M2.5x5(25pcs) Package NO. Name Components Number 11 Center Frame SE021201、SE021301、SE021401、SE021501、 SE021502 、SE021503、SE021601、M2x9、M2.5x5 12 Center Frame Top Board SE021201、M2x9、M2.5x5 13 Center Frame Bottom Board SE021301、M2.5x5 14 Top Board Cover SE021401、M2x9 15 Arm Mounting Bracket SE021501、SE021502、SE021503、 M2x9、M2.
Landing Gear SE032802 SE031801 SE033301 SE031901 M2.5x5 ( 2pcs ) SE032901 SE032204 SE033102 SE032801 SE032803 M3x8( 4pcs ) SE032803 SE032801 SE033001 SE032802 SE032804 HC_M3x8( 2pcs ) M2 . 5x5 ( 4pcs ) SE032201 SE032202 M3x5 ( 2pcs ) SE033103 SE033104 HC_M2 . 5x10 ( 4pcs ) SE032101 SE032001 SE032401 SE031701 SE031702 SE032402 SE033201 PM2 x3 . 5x4 SE032301 M3x8 SE032302 (1) SE033203 SE032501 SE8032502 SE8032402 SE033202 M2.5x8 SE033201 SE033401 ( 7pcs ) (2) SE032502 HC_M2.
26 Base Tube SE032601、SE032701 27 Silicone Rubber Damper SE032701 28 Damping Unit (Set) SE032801、SE032802、SE032803、SE032804、HC_M3x8 29 Aluminum Tube of H-Frame SE032901 30 Silicone Rubber of H-Frame SE033001 31 Battery Tray SE033101、SE033102、SE033103、SE033104、M2.5x5、M3x5 32 33 34 35 Control arm of Retractable Module(Left) Control Arm of Retractable Module(Right) Shaft Sleeve of Retract Module IMU Mount SE033201、SE033202、SE033203、M2.5x8 SE033301、SE033202、SE033203、M2.
M2.5(4pcs) SE014401 S E 014402 Package NO. 44 Name Vibration absorber of Motor Components Number SE014401、SE014402、M2.