Spreading Wings S800 User Manual V 1.7 2012.12.24 Revision www.dji-innovations.com ©2012 DJI Innovations. All Rights Reserved.
Disclaimer Read this disclaimer carefully before using Spreading Wings S800. By using this product, you hereby agree to this disclaimer and signify that you have read them fully. Spreading Wings S800 is an excellent multi-rotor. With a good autopilot, it will offer tremendous flight features.
S800 Profile DJI Spreading Wings S800 is a multi-rotor designed for AP. It simplifies users’ installation and enables quick disassembling. Frame arm integrates with ESC and motor. With DJI WKM autopilot system, it can achieve hovering, cruising and other flight elements. S800 can be applied for aerial photography and other aero-modeling activities. 350mm(Lengh th) 240mm(Diam eter) m 5m th) 14 Wid p (To 320mm(Height) 41 5m m id (W ) th 500 ©2012 DJI Innovations. All Rights Reserved.
Contents Disclaimer.......................................................................................................................2 S800 Profile ....................................................................................................................3 Contents .........................................................................................................................4 Product Usage Cautions.......................................................................................
Product Usage Cautions When flying, the fast rotating propellers of S800 may cause serious damage(s) and injuries. Therefore, please fly with a high safety in mind at all time. Mount Attention Mount GPS with a bracket, to avoid interference from the power board of center frame. For IMU position, make sure the arrow direction marking is pointing to the aircraft nose.
In Box Center Frame 800CF×1 Frame Arm 800FA×6 H Frame 800HF ×1 T Frame 800TF×2,Aluminum Ring 800AR×2 Base Pipe 800BP×2 Bi-pod Drawbar 800BD×4 Silicone Rubber Damper 800SRD×4 Nonslip Damper 800ND×4 3-PIN Servo Cable 800SC ×1 Screw Package 800SP ×1 Hexagonal screws: M3×8、M2.5×5 Hexagonal socket head cap screws: HC-M3.0×22 、 HC-M2.5×5、HC-M2.5×8、 HC-M3×8、T2×9 Adhesive Velcro 800AV ×1, Battery Band 800BB ×2 Tools Needed 2.0mm Hex Wrench, 2.5mm Hex Wrench For mounting screws.
Center Frame Wiring Top board is power distribution board, and the bottom board is for loading autopilot system components.
Mount Center Frame Remove Screws Fix Screws Step1: Mount IMU module into IMU position in the center frame. Ensure IMU casing is out of touch the top board edge, as vibration can cause IMU mal-function. Step2: Please mount DJI Autopilot System parts onto the bottom board (not including GPS modules). Please remove all the screws from the bottom board first if necessary. Step3: Connect Autopilot System and receiver. Please refer to DJI WKM User Manual for details.
Mount Frame Arms Step 1 Step 2 800CF ×1 800FA ×6 Copper contacts Propeller Screw Cover Motor ESC LED (1) Motor rotation direction Clock-wise Counter clock-wise Red Green Step 3 Step 4 800CF 800FA Step 5 800CF 800FA ×1 ×6 ×1 ×6 Vertical 35o Horizontal Horizontal (2) Step1: Check arms. (1) Make sure copper contacts are in good condition without bend or severe wear. (2) Make sure propellers are without crack, and screws in propeller cover tight.
Slowly rotate the frame arm to prevent from breaking the copper contacts. Please refer to (2) to ensure the arm is perfectly positioned. Make sure use appropriate strength to press down the buckle correctly. Do not hot plug arms. If the motor mount loosens, please tighten it by following the procedures in trouble shooting of Appendix. Tips: LED is on after motor start. Examination Arms①②are aircraft nose direction, arms④⑤ are aircraft tail.
Mount Bi-pod Step1 Step2 (Fix, but not tighten screws) 800HF 800BD 800AR HC-M2.5X5 X1 X4 X2 X8 Step3 M2.5X8 3.0 HC-M3.0X22 x4 x2 H frame bulges outwards T frame notch Step1: Mount T frame 800TF and base pipe 800BP. (1) Put nonslip damper 800ND through the base pipe. (2) Put the base pipe into T frame until the head of nonslip damper is embedded into T frame. (3) Embed the other nonslip damper into the T frame. (4) Put silicon rubber damper 800SRD onto both sides of the base pipe.
Step3: Mount H frame and T frame. (1) Insert T frame through aluminum ring until it plugs into H frame. (2) Fix T frame notch into H frame bulges outwards, make sure T frame will not move. (3) Put the bi-pod on the flat floor to adjust H frame and T frame. (4) Tighten all hexagonal socket head cap screws (including ① and ②). Notices: Put bi-pod on the flat floor to finish mounting smoothly and correctly. Please mount the screws and use adequate screw glue.
Assembly Assembly ③ ② rc Ai N ft ra e os ④ ⑤ ① ⑥ Align knob to mark Insert knob into arm Rotate knob (2) (1) Knob Mark Step1: Align all knobs on the H frame to the marks; refer to fig (1). Step2: Lie frame and bi-pod horizontally, insert knobs into arms ③ and ⑥ first, and then adjust to insert others into the arms. Step3: Rotate the knob to the end, as fig (2) shown. Notices: Ensure all knobs on the H frame aligned to the marks, and they would go through the arms successfully.
ESC Sound ESC State Sound Ready ♪1234567 Throttle stick is not at bottom BBBBBB… Input signal abnormal B--------B--------B… Input voltage abnormal BB---BB---BB---BB… Tips: DJI ESCs are specially designed for multi-rotors. When use with DJI autopilot systems, you do not have to setup any parameters or calibrate travel range.
Current 40A OPTO Voltage 6S LiPo Signal Frequency 30Hz ~ 450Hz Drive PWM Frequency 24KHz Weight 18g Propeller Material Carbon Fiber Size 15×04in Weight 15g Flight Parameters Takeoff Weight 5.0Kg ~ 7.0Kg Load Weight 0Kg ~ 2.5Kg Power Battery LiPo (6S、10000mAh~15000mAh、15C(Min)) Max Power Consumption 2100W Hover Power Consumption 720W(@ Takeoff Weight 6Kg) Hover Time Max: 16 min (@10000mAh&6KgTakeoff Weight) ©2012 DJI Innovations. All Rights Reserved.
Appendix Mount Battery Bracket Step1: Mount the retaining clip and the bracket, fix screws (but not tighten). M 2.5X5 Bracket Notch Outwards Retaining Clips Chamfer Outwards Step2: Place the mounting board and adjust its position, and then tighten all screws. About 13 1mm Ensure to Parallel Parallel Parallel ©2012 DJI Innovations. All Rights Reserved.
Trouble Shooting If the motor mount loosens, please tighten it by following the procedures. Step1 For arms For arms Shim Step2 Motor mount screws Step3 For arms For arms Step1: Remove. Please unscrew the screws on the top. Step2: Tighten. Retighten the motor mount screws on the back to make the motor firmly attached. Step3: Remount. Remount the screws on the top. Notices: Shim should be mounted in the correct position, as shim mount position of arm is different from arm .
Spare Parts Listing If S800 needs part replaced, please refer to the following diagram to identify the part with the NO. and components, and then make a purchase. Each package includes screws needed. Frame Arm M3x8 S8010301 S8010101A S8010302 T2X9 S8010401A M2.5x5 S8010303 S8010402 M2.5x5 S8010403 S8010404 S8010601 S8010602R/ S8010602G M2.5x5 NO.
Ensure to solder thick wires and fine wires correctly, when solder ESC to frame arm. Clockwise and counter clockwise motor should be soldered to ESC correctly by different color order. For arms For arms Red Black G Fine wire G G Fine wire P P V V Wire Blue Thick wire G Enamel Solder pad Blue Black Red Thick wire Red Black P P G Fine wire G Fine wire G Wire Blue Thick wire G Shield Solder pad Blue Black Red V V Thick wire Center Frame T2X9 S8021201 M2.
NO. Name Components 9 Arm Mounting Bracket S8020901、S8020902、S8020903、S8020904 10 Center Frame Support Pillar S8021001 11 Center Frame Top &Bottom Board S8021101、S8021102 12 Top Board Cover for Arm Mounting Bracket S8021201 Bi-pod S8031402 S8031301 S8031302 S8031507 S8031501 S8031502 S8031505 S8031503 S8031303 HC-M3X8 S8031504 HC-M3X8 S8031506 S8031401 S8031506 S8032101 HC-M3X22 S8032204 S8031505 S8032201 S8032202 S8031507 S8032203 HC-M2.5X8 S8032102 S8032103 HC_M2.
16 T-Frame(Right) S8031601、S8031602、S8031603 17 T-Frame(Left) S8031601、S8031602、S8031604 18 T-Frame Nonslip Damper (4pcs) S8031801 19 T-Frame Silicone Rubber Damper (4pcs) S8031901 20 Bi-pod Carbon Tube S8032001 21 Bi-pod Drawbar S8032101、S8032102(2pcs) 、S8032103 22 Battery Tray S8032201、S8032202、S8032203、S8032204 23 Bi-pod Carbon Tube Bracket(Left Set) 24 Bi-pod Carbon Tube Bracket(Middle Set) 25 Bi-pod Carbon Tube Bracket(Right Set) 26 Screw Pack M2.
