EP DISCLAIMER AND SAFETY GUIDELINES V1.0 2020.
Glossary The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product. Procedures, which if not properly followed, create a possibility of physical property damage AND possibility of injury. Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of serious injury. The DJITM ROBOMASTERTM EP robot is a sophisticated product.
Check all of the included parts listed in the In the Box section in the quick start guide, and read the disclaimer and safety guidelines. Complete the assembly with the help of the quick start guide and the video tutorial on DJI’s official website (http://www.dji.com). Refer to the RoboMaster S1 User Manual on DJI’s official website for more comprehensive information. Make sure you fully understand all safety guidelines, government regulations, and the functionality of each individual part.
8. DO NOT use frozen gel beads. Frozen gel beads may block the blaster or could potentially cause injury or property damage. 9. If the robot will not be used for an extended period, power it off to avoid accidents. Chassis and Mecanum Wheels To avoid component malfunction, serious injury, and property damage, observe the following rules: 1. If the Mecanum wheels or chassis are moving at a high speed, they could potentially cause injury or property damage.
Intelligent Battery To avoid fire, serious injury, and property damage, observe the following safety guidelines when using, charging, or disposing of a battery. Battery Use 1. DO NOT allow the batteries to come into contact with any kind of liquid. DO NOT leave the batteries out in the rain or near a source of moisture. DO NOT drop the battery into water.
2. DO NOT leave the battery unattended during charging. DO NOT charge the battery near flammable materials or on flammable surfaces such as carpet or wood. 3. DO NOT charge the battery immediately after use. Wait until it cools down to near room temperature. Charging the battery outside of the temperature range of 5° to 40° C (41° to 104° F) may lead to leakage, overheating, or battery damage. 4. Disconnect the charger when not in use.
2. Make sure the connections between all the motors and the motion controller are stable. 3. If the motor cannot rotate freely, immediately power it off and check. Armor 1. Make sure that all the armor is securely mounted, all cables are firmly connected to the motion controller, and that they are functioning properly. Gimbal 1. The gimbal includes delicate parts that may be damaged when the gimbal is impacted. Protect the gimbal from physical damage. Otherwise, the gimbal motor may malfunction. 2.
4. Clean the lens regularly to avoid blurring or halos. Use a special lens cleaner to make sure that there is no foreign matter on the lens after cleaning and that it does not damage the lens. Intelligent Controller 1. Make sure that all the cables are connected and all connected parts work properly before use. 2. Make sure that the antennas on the intelligent controller are unfolded and adjusted to the proper position for optimal communication. 3.
is lower than 30%. Only discharge the battery in a fireproof location. Store Intelligent Batteries in a ventilated location. 1. Secure the gimbal and Mecanum wheels before transportation. 2. When stored for an extended period, make sure to attach the chassis rear cover firmly to prevent the ports on the motion controller from being exposed. Otherwise, it may become moist and corroded, which affects the service life. 3.
Compliance with Regulations & Operation Limits 1. Make sure you understand and comply with the local laws and regulations and, if required, have obtained corresponding approval and clearance from the related government agencies before use. 2. Respect the privacy of others when using the image capture, sound recording, and video recording functions.
有害物质 部件名称 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr+6) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 线路板 × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 金属部件（铜合金） × ○ ○ ○ ○ ○ 内部线材 × ○ ○ ○ ○ ○ 其他配件 × ○ ○ ○ ○ ○ 本表格依据 SJ/T 11364 的规定编制。 ○：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。 ×：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。（产品符合欧盟 ROHS 指令 环保要求） NCC Compliance Notice 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大 功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應改善至無干 擾時方得繼續使用。前項合法通信，指依電信法規定作業
This content is subject to change. Download the latest version from https://www.dji.com/robomaster-ep If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. and are the trademarks of DJI. Copyright © 2020 DJI All Rights Reserved.
