DJI FOCUS V1.2 2015.
Searching for Keywords Search for keywords such as “battery” and “install” to find a topic. If you are using Adobe Acrobat Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to begin a search. Navigating to a Topic View a complete list of topics in the table of contents. Click on a topic to navigate to that section.
Disclaimer and Warning Congratulations on purchasing your new DJI product. The information in this document affects your safety and your legal rights and responsibilities. Read this entire document carefully to ensure proper configuration before use. Failure to read and follow instructions and warnings in this document may result in serious injury to yourself or others, or damage to your DJI product or damage to other objects in the vicinity.
Contents Disclaimer and Warning 3 Using this Manual 3 Legend 3 Before You Begin 3 Introduction 5 In the Box 5 Remote Controller 7 Motor 8 Getting Started 9 Prepare the Remote Controller Mounting the Lens Gear Ring 10 Prepare the Motor 11 Mounting the Motor 12 Linking 14 System Status Indicator 14 Settings 15 Calibration 15 Menu 16 Quick Focus 17 Locking the Remote Controller 17 Focus Wheel Settings 18 Used with the Zenmuse X5 19 Connection 19 Settings 19 Firmwar
Introduction DJI Focus is a wireless follow focus system that comprises of a remote controller and motor unit. The low noise motor produces 25 dB of noise at 96 rpm, and has a maximum speed and torque of 192 rpm and 0.35 Nm respectively. The system can be operated in wireless mode or cable mode. In the Box Check that all of the following items are included in the package. If any items are missing, contact DJI Support or your local DJI authorized dealer.
DJI FOCUS User Manual Micro USB Cable ×1 Use to charge or upgrade the remote controller. Marking Ring ×3 Mark down the focus values for individual lenses on this ring for reference. Lens Gear Ring ×4 0.8 Mod, 105 Teeth Inner Diameter: 60 mm 0.8 Mod, 105 Teeth Inner Diameter: 70 mm 0.8 Mod, 105 Teeth Inner Diameter: 80 mm 0.8 Mod, 105 Teeth Inner Diameter: 90 mm Neck Strap ×1 For carrying the remote controller around the neck or over the shoulder between takes. 6 © 2015 DJI. All Rights Reserved.
Remote Controller [1] [2] [3] [11] [4] [10] [5] [12] [14] [13] [9] [8] [7] [6] [1] Antenna Transmits at 2.4 GHz. [2] Power Button Press and hold for 2 seconds to power on/off the remote controller. [3] Communication Port Allows the motor to communicate with the remote controller. Allows the motor to be upgraded. [4] Marking Ring Used to provide marking scale. [5] Focus Wheel Used to adjust the lens of your camera. [6] Micro USB Port Used to charge or update the remote controller.
DJI FOCUS User Manual [15] [18] [16] [17] [15] Rosette Mount For mounting accessories. [17] Lanyard Hole Used to attach the neck strap. [16] Rear Screw Needs to be removed in order to take off the battery cover for battery replacement. [18] Link Button Used to link the remote controller to the motor or enter forced update mode. Motor [2] Gear Turns the gear ring on the camera lens. [3] Quick-Release Mount For mounting the motor onto the camera.
Getting Started Prepare the Remote Controller Charge the Battery The remote controller contains a 1700 mAh battery that can power the device for up to 14 hours. Charge the battery through the Micro USB port located on the side and check the battery level on the OLED screen. To replace the battery, remove the screw and battery cover on the back of the remote controller. Micro USB Port WARNING Screw Only use official DJI batteries that can be purchased on www.dji.com.
DJI FOCUS User Manual Attaching the Neck Strap Pull down and hold the button on the neck strap connector, slide it through the mounting hole on the bottom of the remote controller, and then release the button. CAUTION Ensure the neck strap is attached securely. Mounting the Lens Gear Ring DJI Focus comes with four sizes of lens gear rings. Choose the lens gear ring that best fits your camera lens. Ensure the screw is tight and that the lens gear ring makes good contact with the lens.
DJI FOCUS User Manual Prepare the Motor The motor gear can be mounted on either side of the motor. To remove the gear, loosen the knob at the center the gear. Ensure the gear is mounted securely. The motor can be clamped to a 15 or 19 mm support rod. To clamp the motor to a 19 mm support rode, first remove the two adapters on the clamp: 1. Loosen the knob and remove the quick-release mount. 1 2 2. Push the knob away from the clamp and open up the clamp. Slide and remove the two adapters on the clamp.
DJI FOCUS User Manual Mounting the Motor To mount the motor onto your camera support rod: 1. Loosen the knob on the quick-release mount and slide the motor onto the support rod. Tighten the knob to secure the motor’s position on the support rod. 2. Tighten the knob to secure its position. Ensure the motor gear and lens gear ring make good contact. Ensure the lens gears are not too tight to avoid premature wear to the gears or damage to the lens. Lens Gear Ring Motor Gear 3.
DJI FOCUS User Manual Ensure the motor is mounted firmly. Keep your fingers, hair and clothing away from the motor when it is in operation. 4. DJI Focus can work in wireless mode or cable mode. To use cable mode, connect the communication port on the remote controller to the communication port on the motor using the signal cable. TIPS Cable mode will take precedence over wireless mode. Ensure the motor is connected to an external power supply. © 2015 DJI. All Rights Reserved.
DJI FOCUS User Manual Linking Linking is only required when the remote controller or motor is replaced with a new one. To link the remote controller to the motor: 1. Turn on both devices. 2. Press the link button on the bottom of the remote controller, or use the navigation buttons to enter Menu Settings Connect Motor Connect. Settings Power Off Connect Motor Back Select Link Button 3. Within the next 5 seconds, press the link button on the motor. Link Button 4.
Settings When both the remote controller and motor are turned on. The OLED screen of the remote controller will display the following information. [1] Battery Level [7] [1] [6] [2] 50.
DJI FOCUS User Manual TIPS The motor will automatically reserve a 1mm margin at both mechanical limits for protection. When to Calibrate 1. If there is an ‘OK’ icon on the OLED screen, the motor is working normally and does not need calibration. 2. If there is an ‘OK’ icon on the OLED screen but it is blinking, the motor was moved to a different mounting position and needs to be re-calibrated. 3.
DJI FOCUS User Manual Quick Focus Allows rapid switching between four preset focus points. Assigning a Focus Point Adjust the lens focus to the desired focus point by turning the focus wheel. Hold down one of the letters until it blinks to store the focus point. To reassign a focus point, press and hold the letter to discard its value, and then redo the first step. Switching to a Focus Point Press one of the letters to apply its assigned focus point.
DJI FOCUS User Manual Focus Wheel Settings Setting Mechanical Limits The two adjustable hard stop screws around the focus wheel can be used to limit the travel range physically. 1. Loosen the hard stop screws, slide them to the desired positions and tighten. 50.0% 2. The travel range of the focus wheel is now limited to the distance between the two hard stop screws. Calibrate Menu 50.
Used with the Zenmuse X5 DJI Focus is fully compatible with the Zenmuse X5 series gimbal and camera. No calibration is required when using the Focus with the Zenmuse X5 camera. Connection To allow communication between the two devices, connect the communication port on the Focus remote controller to the CAN Bus port on the Inspire 1 remote controller using the dedicated CAN Bus cable. TIPS Ensure that the Zenmuse X5 camera is set in AF mode. The remote controller overrides the in-app controls.
DJI FOCUS User Manual travel limit and select Set Point 2. Turning the focus wheel from Point 1 to Point 2 will rotate the camera focus by a full cycle. LED Control: Enable or disable the LED and system status indicators on the remote controller and motor individually. Default: Restores the default settings for the remote controller. About Displays the current firmware version of the remote controller.
DJI FOCUS User Manual Upgrade You can view the latest firmware versions of all components on this page. Upgrading the Remote Controller Turn ON the controller and connect it to your computer via the Micro-USB cable and wait until the indicator LED in the Assistant blinks blue. Click Upgrade to upgrade the Follow Focus Remote, and then upgrade the Follow Focus Remote Radio.
Troubleshooting The motor does not respond to the remote controller. 1. Make sure you have calibrated the motor at least once. The motor will not respond unless it has been calibrated for the first time. 2. Check for any bent or damaged pins on the data cable plugs. Replace the cable if necessary. 3. Ensure the polarity of the power cable is correct and the P-Tap is firmly connected to the power supply. 4. Try connecting the motor to the remote controller directly using the data cable. 5.
If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. © 2015 DJI. All Rights Reserved.
