MATRICE 600 PRO User Manual V1.0 J 2018.
Q Searching for Keywords Search for keywords such as “battery” and “install” to find a topic. If you are using Adobe Acrobat Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to begin a search. Navigating to a Topic View a complete list of topics in the table of contents. Click on a topic to navigate to that section. Printing this Document This document supports high resolution printing.
Using This Manual Legends 0 Warning Important Hints and Tips Reference Information The MATRICETM 600 Pro does not include a gimbal or camera. A corresponding gimbal or camera is required for certain functions mentioned in this manual. Before Flight The following tutorials and manuals have been produced to help you get the most out of your Matrice 600 Pro. 1. In the Box 2. Disclaimer and Safety Guidelines 3. Quick Start Guide 4. Intelligent Flight Battery Safety Guidelines 5.
Warning The rotating propellers can cause serious damage and injury. Fly with caution at all times. Assembly Warning 1. Ensure that all other parts are installed before inserting the Intelligent Flight Batteries. 2. DO NOT remove any glued-in screws. 3. The Matrice 600 Pro should be lifted off the ground when testing the landing gear or recalibrating servo travel. Flight Warning 1. The aircraft is not waterproof. DO NOT fly in rainy or snowy weather. 2.
Contents Using This Manual 1 Warning 2 Product Profile 5 Introduction 5 Highlighted Features 5 Installation 6 Mounting the Landing Gear 6 Unfolding the Aircraft 6 Mounting the Gimbal (Optional) 7 Intelligent Flight Battery Profile 8 8 Intelligent Flight Battery Functions 8 Using the Batteries 9 Remote Controller 14 Profile 14 Preparing Remote Controller 14 Remote Controller Overview 14 Remote Controller Operations 16 Dual Remote Controllers Mode 21 Remote Controller LEDs
DJI GO App 32 Editor 35 Skypixel 35 Me 35 Flight 36 Flight Environment 36 Flight Limits and No Fly Zones 36 Pre-Flight Checklist 39 Flight Status Indicators 40 Calibrating the Compass 41 Auto Takeoff and Auto Landing 42 Starting and Stopping the Motors 42 Stopping the Motors Mid-flight 43 Flight Test 43 Appendix 4 32 Equipment 44 Specifications 44 Intelligent Flight Modes 47 Upgrading the Firmware 48 Retractable Landing Gear 49 Reserved Mounting Position Dimensions
Product Profile Introduction The Matrice 600 Pro is a six-rotor flying platform designed for professional aerial photography and industrial applications. It is equipped with a dedicated DJITM A3 Pro triple-modular redundancy system and advanced intelligent flight functions, ensuring safe and stable operation at all times. Its mechanical design, with quick-release landing gear and mounted folding arms, make it easy to transport, store, and prepare for flight. With a maximum takeoff weight of 15.
Installation Mounting the Landing Gear 1. Ensure the screw on the landing gear leg is pointing in the same direction as the gap next to the knob on the landing skid. Insert both landing gear legs into a corresponding landing skid, rotate the landing gear leg until it is fully seated into the landing skid, and then secure it in place by tightening the knob. 2. Ensure the hook on the landing gear leg is facing toward the outside of the aircraft, then attach it to the connector on the aircraft body.
MATRICE 600 PRO User Manual Mounting the Gimbal (Optional) The built-in flight control system of the Matrice 600 Pro is compatible with the following DJI gimbals and cameras. Ronin-MX Zenmuse Z30 Zenmuse Z3 Zenmuse X3 Zenmuse X5 Series Zenmuse XT, XT 2 Zenmuse Z15 Series HD Gimbal: Z15-A7, Z15-BMPCC, Z15-5D III, Z15-GH4 Different accessories are used to mount different gimbals or cameras. Purchase corresponding accessories according to your needs. Refer to DJI Zenmuse X3 Gimbal and Camera (p.
Intelligent Flight Battery Profile The Matrice 600 Pro has six battery compartments and six Intelligent Flight Batteries to extend the flight time. The standard Intelligent Flight Battery has a capacity of 4500mAh, voltage of 22.2V, and built-in smart charge-discharge function. It can only be charged with an appropriate DJI approved charger. Intelligent Flight Battery DJI Hex Charger The Intelligent Flight Battery must be fully charged before first-time use. Intelligent Flight Battery Functions 1.
MATRICE 600 PRO User Manual Using the Batteries Installing the Batteries There are six battery compartments on the Matrice 600 Pro. You must load all six battery compartments with batteries of the same model before each flight. Make sure all the batteries are fully charged before each flight. Never insert the Intelligent Flight Battery into or remove it from the battery compartment of the Matrice 600 Pro when it is powered on.
MATRICE 600 PRO User Manual If the power supply is not OK when powering on the batteries, the DJI GO app will either prompt you to adjust the battery positions or tell you there is a large voltage difference. To adjust the battery positions: 1. Power off all the batteries. 2. Adjust battery positions by following the tips in the DJI GO app. 3. Ensure all the battery positions are correct and then power on one of the batteries. The other batteries will power on automatically if the positions are correct.
MATRICE 600 PRO User Manual Battery Level Indicator LED1 LED2 LED3 LED4 Battery Level 87.5%~100% 75%~87.5% 62.5%~75% 50%~62.5% 37.5%~50% 25%~37.5% 12.5%~25% 0%~12.5% =0% Checking the Battery Life The battery life indicates the number of cycles the battery can be charged and discharged before it must be replaced. When the battery is powered off, press and hold the power button for 5 seconds to check the battery life.
MATRICE 600 PRO User Manual Charging the Intelligent Flight Battery The Matrice 600 Pro is shipped with a DJI Hex Charger. It can charge up to six Intelligent Flight Batteries and two remote controllers simultaneously. 1. Connect the Hex Charger to a power outlet (100-240V, 50/60Hz) with the power cable. 2. Insert the Intelligent Flight Battery into the battery port to begin charging. 3.
MATRICE 600 PRO User Manual Charging Protection LED Display The table below describes the battery protection mechanisms and their corresponding LED patterns.
Remote Controller Profile The remote controller integrates video downlink and aircraft control into one system. The combined system operates at 2.4 GHz with a maximum signal transmission range of 5 km. The device features a number of standard and customizable buttons that allow users to quickly access certain aircraft functions, such as taking and reviewing photos/videos, as well as controlling the gimbal and landing gear. It is powered by a 2S rechargeable battery.
MATRICE 600 PRO User Manual [5] Landing Gear Control Switch Toggle the switch up or down to raise or lower the landing gear. [6] Battery Level LEDs [8] Power Button Used to power on or power off the remote controller. [9] RTH Status LED Displays the current battery level. Circular LED around the RTH button displays RTH status. [7] Status LED Displays the power status. [16] [18] [17] set number of photos will be taken with one press.
MATRICE 600 PRO User Manual Remote Controller Operations Powering On and Off the Remote Controller The Matrice 600 Pro remote controller is powered by a 2S rechargeable battery with a capacity of 6000mAh. The battery level is indicated by the Battery Level LEDs on the front panel. Follow the steps below to power on your remote controller: 1. When powered off, press the Power Button once and the Battery Level LEDs will display the current battery level. 2.
MATRICE 600 PRO User Manual Controlling the Camera Shoot videos or images and adjust camera settings via the Shutter Button, Camera Settings Dial, Playback Button and Video Recording Button on the remote controller when using a Zenmuse Z30, Z3, X3, X5 series, XT or XT 2 gimbal and camera. [1] [4] [2] [3] [1] Camera Settings Dial Turn the dial to quickly adjust camera settings such as ISO and shutter speed without letting go of the remote controller.
MATRICE 600 PRO User Manual Remote Controller Aircraft ( indicates nose direction) Function Moving the Left Stick up/down changes the aircraft’s elevation. Push it up to ascend and down to descend. Use this stick to take off when the motors are spinning at idle speed. The aircraft will hover in place if the Left Stick is released. Moving the Left Stick left/right changes the heading of the aircraft. Push it left to rotate the aircraft counter clock-wise, and right to rotate the aircraft clockwise.
MATRICE 600 PRO User Manual Flight Mode Switch Toggle the switch to select the desired flight mode. You may choose between P-mode, A-mode and F-mode. Figure P Flight Mode P P-mode A A-mode F F-mode A F P-mode (Positioning): P-mode works best when GPS signal is strong. There are several states in P-mode which are automatically selected by the Matrice 600 Pro depending on GPS signal strength: P-GPS: GPS is available. The aircraft uses GPS for positioning. P-ATTI: GPS is not available.
MATRICE 600 PRO User Manual 1. Raise: Raise the landing gear to its upper most position. The landing gear will automatically raise when the aircraft reaches an altitude of 1.2 m for the first time. 2. Lower: The landing gear will lower to its lowest position for landing. The landing gear will automatically lower if Auto-Landing is enabled in the DJI GO app or when the aircraft is landing automatically as part of the RTH procedure.
MATRICE 600 PRO User Manual Optimal Transmission Range The signal transmission between the aircraft and the remote controller performs best when the aircraft is within the optimal transmission range. Open up the antennas on the remote controller to optimize transmission range. Ideally, the flat surface of the antenna should be facing the aircraft. If the signal is weak, fly the aircraft closer to you.
MATRICE 600 PRO User Manual Setting Up Dual Remote Controllers Mode The Dual Remote Controllers mode is disabled by default. Users must enable this feature on the Master Remote Controller through the DJI GO app. Follow the steps below for setup: Master Remote Controller: 1. Connect the remote controller to your mobile device and launch the DJI GO app. 2. Go to the Camera View, and tap to enter the remote controller settings window. 3.
MATRICE 600 PRO User Manual 2. Tap Search for Master Controller to register the Master remote controller. Remote Controller Settings Remote Controller Settings Master and Slave Set Remote Controller Status Remote Controller Name OFF Master Slave S88642 Request Control Remote Controller Settings Search for Master Controller Master RC List T12254 Remote Controller Settings Master and Slave 3.
MATRICE 600 PRO User Manual Status LED Alarm Remote Controller Status — Solid Red chime The remote controller is set as Master but is not connected to the aircraft. — Solid Green chime The remote controller is set as Master and connected to the aircraft. — Solid Purple 2 beeps The remote controller is set as Slave but is not connected to the aircraft. — Solid Cyan 2 beeps and chime The remote controller is set as Slave and connected to the aircraft.
MATRICE 600 PRO User Manual 3. The remote controller Status LED will blink blue and beep to indicate that the remote controller is ready to be linked. Remote Controller Settings Remote Controller Calibration Stick Mode Searching for aircraft frequency, Default stick mode is Mode 2, changing stick modes alters the way the aircraft is controlled. timeout in 54 seconds Do not change unless familiar with your new mode.
Return-to-Home (RTH) Profile The Return-to-Home (RTH) function brings the aircraft back to the last recorded Home Point. There are three events that will trigger RTH procedure: Smart RTH, Low Battery RTH and Failsafe RTH. Description GPS The default Home Point is the first location where your aircraft received strong GPS signals (i.e. the white GPS icon is followed by at least four white bars ). You can update the Home Point via the DJI GO app. Refer to Updating Home Point (p. 28) for details.
MATRICE 600 PRO User Manual Battery Level Aircraft Status Indicator Description Flight Instructions DJI GO App Tap Go-Home to make the aircraft return to Home Point Low Battery The battery level is Warning low. Please land the aircraft. Aircraft Status and land automatically, or Indicator Cancel to resume normal blinking RED flight. If no action is taken, slowly. the aircraft will automatically return to the Home Point and land after 10 seconds.
MATRICE 600 PRO User Manual RTH Safety Notices The aircraft cannot avoid obstruction during RTH, therefore it is important to set a reasonable RTH altitude before each flight. Go to the DJI GO app > Camera View > > Set Return-to-Home Altitude.
A3 Pro Redundancy System The Matrice 600 Pro’s A3 Pro flight control system is an upgraded version of the A3, which enhances flight safety. The A3 includes a flight controller, GPS-Compass Pro and a PMU (Power Management Unit). With two additional IMU Pro and GPS-Compass Pro modules, the A3 Pro provides triple-modular redundancy, improving the system’s anti-risk performance. Mounting Positions Ensure that the settings of all the IMU Pro modules and GPS-Compass Pro modules are correct before each flight.
DJI Assistant 2 When using your Matrice 600 Pro for the first time, activate it in the DJI Assistant 2 software. Installation and Launching 1. Download the DJI Assistant 2 installation file from the official DJI website: http://www.dji.com/matrice600-pro/info#downloads 2. Complete the installation for the DJI Assistant 2 software. 3. Launch the DJI Assistant 2 software. Using the DJI Assistant 2 1. Ensure that all the six Intelligent Flight Batteries are fully charged and then install them. 2.
MATRICE 600 PRO User Manual API Control and the Intelligent Flight Modes cannot be used at the same time. If you are using Intelligent Flight Mode, finish the current intelligent flight mission and toggle the Flight Mode Switch to F-mode again to use API Control. API Control is automatically disabled after firmware updates. Re-enable this option if necessary.
DJI GO App Use the DJI GO app to configure your aircraft. If using a gimbal or camera, you can also control the gimbal or camera in the app. The Library, Skypixel, and Me sections in the app allow you to share your content with friends. 4:21PM iPad 22% MATRICE 600 PRO Aircraft Connected Camera Learn more Equipment Editor Skypixel Me Equipment On the Equipment page, you can enter Camera View, visit the Academy or view your flight records.
MATRICE 600 PRO User Manual [1] System Status : Indicates the current aircraft system status and GPS signal strength. Ready to Go (GPS) [2] Battery Level Indicator : Describes the battery level of the aircraft according to its immediate status. The colored zones represent the various stages of battery level. When the battery level drops to a certain stage, the system will prompt the user to take the appropriate action. [3] Flight Mode : The text next to this icon indicates the current flight mode.
MATRICE 600 PRO User Manual [10] Mini Map Displays the flight path of the current flight. Tap the Mini Map to switch between Camera View and Map View. [11] Flight Telemetry D 210 M H H.S 4.2 M/S 30 M VS 2.3 M/S 232 M Flight Attitude and Radar Function: The aircraft’s flight attitude is indicated by the target-like icon. (1) The red arrow shows which direction the aircraft is facing. (2) The ratio of the grey area to the blue area indicates the aircraft’s pitch.
MATRICE 600 PRO User Manual Follow Mode The gimbal’s orientation is aligned with the aircraft’s nose. One user alone can control the pitch motion of the gimbal, but a second operator is required to control the yaw motion using a second remote controller. FPV Mode The gimbal will lock to the movement of the aircraft to provide a FirstPerson-View flying experience. Free Mode The gimbal’s motion is independent of the aircraft’s orientation.
Flight Once pre-flight preparation is complete, it is recommended to use the flight simulator to learn how to fly safely. Ensure that all flights are carried out in an open area. Flight Environment 1. Do not use the aircraft in adverse weather conditions including rain, snow, fog, and wind speeds exceeding 8 m/s. 2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the compass and the GPS signal. 3.
MATRICE 600 PRO User Manual Safe to Fly (GPS) Blinking Green Slowly Flight Limits DJI GO App Max Height Flight altitude must be below the preset height. Warning: Height limit reached. Max Radius Flight distance must be within the max radius. Warning: Distance limit reached. Safe to Fly (No GPS) Blinking Yellow Slowly Flight Limits DJI GO App Max Height If the Max Flight Altitude set in the DJI GO app is ≤ 50m*, the flight altitude will not exceed the preset value.
MATRICE 600 PRO User Manual 2. R1 miles around the airport (depending on its shape and size) encompasses the no fly zone, inside of which takeoff and flight are prohibited. 3. From R1 to R1+1 miles around the airport, the flight altitude is limited at a 15 degree incline, starting at 66 feet (20 meters) from the edge of airport and radiating outwards. The flight altitude is limited to 1640 feet (500 meters) at R1+1 miles. 4.
MATRICE 600 PRO User Manual Safe to Fly (GPS) Zone No Fly Zone AltitudeRestricted Zone Warning Zone Free Zone Blinking Green Slowly Aircraft Status Indicator Restrictions DJI GO App Warning Motors will not start. Warning: You are in a no fly zone. Takeoff prohibited. If the aircraft loses GPS signal and enters the restricted area but regains GPS signal afterwards, the aircraft will enter SemiAutomatic Descent and land itself. Warning: You are in a no fly zone. Automatic landing has begun.
MATRICE 600 PRO User Manual 5. All cables are connected correctly and firmly. 6. The DJI GO app is connected to the aircraft. 7. Motors start properly and are functioning as normal. Flight Status Indicators ESC LEDs Aircraft Status Indicator ESC LEDs There is an ESC LED on each frame arm of the Matrice 600 Pro to show the orientation of the aircraft after motors started. The ESC LEDs located on frame arms M1 and M2 are red. The ESC LEDs located on frame arms M3 to M6 are green.
MATRICE 600 PRO User Manual Warning Blinking Yellow Rapidly Blinking Red Slowly Blinking Red Rapidly Blinking Red Rapidly for 0.
MATRICE 600 PRO User Manual When to Recalibrate 1. The compass data is abnormal, and the Aircraft Status Indicator is blinking red and yellow alternatively. 2. Flying in a new location, or a location that is different from your last flight. 3. The mechanical structure of the Matrice 600 Pro is changed, i.e. the mounting position of the GPS module is changed. 4. Severe drifting occurs in flight, i.e. the Matrice 600 Pro has difficulty flying in a straight line.
MATRICE 600 PRO User Manual Stopping the Motors There are two methods to stop the motors. Method 1: When the aircraft has landed, push the throttle down and hold. The motors will stop after 3 seconds. Method 2: When the Matrice 600 Pro has landed, push the throttle stick down, then perform the CSC command to stop the motors. Release both sticks once the motors have stopped. OR Method 1 Method 2 When using method 2 to stop the motors, the aircraft may rollover if it doesn’t touch the ground completely.
Appendix Specifications Aircraft Structure Diagonal Wheelbase Dimensions 1133 mm 1668 mm × 1518 mm × 727 mm with propellers, frame arms and GPS mount unfolded (including landing gear) 437 mm × 402 mm × 553 mm with propellers, frame arms and GPS mount folded (excluding landing gear) Package Dimensions 520 mm × 480 mm × 640 mm (L × W × H) Intelligent Flight Battery Quantity 6 Weight (with six TB47S batteries) 9.5 kg Weight (with six TB48S batteries) 10 kg Max Takeoff Weight 15.
MATRICE 600 PRO User Manual Remote Controller 920.6 MHz to 928 MHz (Japan) Operating Frequency 5.725 GHz to 5.825 GHz 2.400 GHz to 2.483 GHz Max Transmitting Distance FCC: 5 km (unobstructed, free of interference) CE: 3.5 km 10 dBm @ 900 M EIRP 13 dBm @ 5.8 G 20 dBm @ 2.
MATRICE 600 PRO User Manual Battery (Optional) Model TB48S Capacity 5700 mAh Voltage 22.8 V Type LiPo 6S Energy 129.96 Wh Net Weight 680 g Operating Temperature 14° to 104° F (-10° to 40° C) Storage Temperature Less than 3 months: -4° to 113° F (-20° to 45° C) More than 3 months: 72° to 82° F (22° to 28° C) Charging Temperature 41° to 104° F (5° to 40° C) Max Charging Power 180 W 46 © 2017 DJI All Rights Reserved.
MATRICE 600 PRO User Manual Intelligent Flight Modes Intelligent Flight Modes allow users to lock the orientation of the aircraft in different fashions or to preplan flight paths. Intelligent Flight Modes only work in F-mode, and users must toggle the flight mode switch to F-mode to activate Intelligent Flight Modes. Point of Interest (POI) Waypoints Record a point of interest (POI). The aircraft’s nose always points towards the POI.
MATRICE 600 PRO User Manual Upgrading the Firmware Upgrading the Aircraft and Lightbridge 2 Air System Firmware Connect the aircraft to the DJI Assistant 2 to upgrade the aircraft’s and Lightbridge 2 Air System’s firmware. Refer to DJI Assistant 2 (p. 30) for details. Upgrading the Remote Controller Firmware The System Status bar in Camera View of the DJI GO app will flash several times if a firmware upgrade is available. Follow these steps to upgrade the firmware via the DJI GO app. 1.
MATRICE 600 PRO User Manual b. Insert the Micro SD card into your PC. Extract all the downloaded files into the root directory of the Micro SD card. While the Matrice 600 Pro is powered off, remove the Micro SD card from your PC and insert it into the Micro SD card slot on the gimbal. Step 3- Upgrade the Firmware a. Ensure the remote controller is powered off and then power on one of the Intelligent Flight Batteries.
MATRICE 600 PRO User Manual If the LED is solid yellow after calibration, a problem has occurred. Ensure that the servos are mounted correctly and then try again. Avoid obstructions during calibration. If the landing gear was obstructed, recalibration will be required, per the above steps. If the “R” and “L” servo cables are reversed, travel will not be measured correctly. Fix the connections and recalibrate the landing gear using the above steps. Landing gear servo travel has been pre-calibrated.
MATRICE 600 PRO User Manual Reserved Mounting Position Dimensions A mounting position for your own devices is reserved at the bottom of the center frame. 1. Remove the twelve M3×6.5 screws at the bottom of the center frame first, and then remove the expansion mounting kit. M3×6.5 Screws Expansion Mounting Kit 2. The dimensions of the reserved mounting position is shown as follows (unit: mm). 149.1 3×M3 Thread depth 4 mm 258.3 Ф38 120° © 2017 DJI All Rights Reserved.
MATRICE 600 PRO User Manual A3 Pro Flight Control System Overview [3] [4] [1] [5] [2] [6] [9] [10] [7] [8] [11] [12] [13] [14] [15] Flight Controller [1] IMU1 Communicates with the IMU Pro module. Connected before delivery. [2] CAN1 Dedicated DJI CAN-Bus port. Communicates with the GPS-Compass Pro module or other DJI devices (e.g. Real Time Kinematic (RTK) GPS system, gimbals). [3] Orientation Arrow Points to the front of the aircraft.
MATRICE 600 PRO User Manual PMU Module [1] Power Port (9V 3A) [3] Provides power to the flight controller. Connected before delivery. [2] iBAT [1] Communicates with the DJI Intelligent Flight Battery. Connected to the battery management system before delivery. [3] 3S-12S [2] Draws power from the DJI Intelligent Flight Battery or other LiPo battery. Connected to the battery management system before delivery.
MATRICE 600 PRO User Manual Lightbridge 2 Air System Overview [8] [1] [2] [9] [7] [6] [5] [4] [3] [1] HDMI IN Supports up to 1080p60 input resolution. This port has been connected to an HDMI cable and the other end of the cable is an HDMI-D connector. [2] AV IN Receives AV input from the camera. [3] Gimbal Port Connects to a DJI gimbal or camera. [4] DBUS Port Sends the remote controller signal to the flight controller. Connected to the RF port on the flight controller upon delivery.
MATRICE 600 PRO User Manual DJI Gimbal Connection Illustrator Ronin-MX Lightbridge 2 Air System A3 Flight Controller CAN1* CAN1* HDMI CAN PWR AV HDMI SRW-60G Receiver FPV Camera SRW-60G Transmitter Ronin-MX When using the Ronin-MX, set the App Output Mode in the DJI GO app to display the image on your mobile device from the camera used with the Ronin-MX.
MATRICE 600 PRO User Manual Zenmuse Z3, X3, X5 Series, XT and XT 2 Lightbridge 2 Air System A3 Flight Controller CAN1* GIMBAL HDMI AV Gimbal Mounting Plate FPV Camera OR Zenmuse Z15 Series HD Gimbal Lightbridge 2 Air System A3 Flight Controller CAN1* GIMBAL HDMI AV OR G7 Z15 Series GCU FPV Camera *You can connect the CAN cable to the CAN Hub on the GPS cable.
MATRICE 600 PRO User Manual DJI Zenmuse X3 Gimbal and Camera Camera Camera Profile The X3 gimbal and camera can record up to 4K 4096×2160p video at 24 fps, and capture 12-megapixel images. It features a 1/2.3” Sony EXMOR CMOS image sensor. Preview of the camera’s POV in the DJI GO app before shooting images and video. Have extra options to shoot stills in burst mode or self-timer mode, and export video in either MOV or MP4 format.
MATRICE 600 PRO User Manual Gimbal Gimbal Profile The 3-axis gimbal provides a steady platform for the camera, allowing you to capture stable video and images. The gimbal can tilt the camera up to 120 degrees and rotate 320 degrees. +30° 0° -320° -90° +320° Under the default settings, turn the gimbal dial on the remote controller to tilt the camera. Note that you cannot simultaneously tilt and pan the camera in the Single Remote Controller mode.
MATRICE 600 PRO User Manual Press the C1 or C2 button to switch between pitch mode and yaw mode. Use the gimbal dial to control the tilt/pan motion of the camera. Using the DJI GO App to Control the Gimbal Follow the steps below to use the DJI GO app to control the gimbal’s pitch/yaw motion: 1. Go to the DJI GO app > Camera View. 2. Tap and hold on the screen until a blue circle appears. 3. Move your finger to control the gimbal’s pitch/yaw motion. Ready to Go（GPS） 09:29 P-GPS 12 61% AE D 210 M H H.
MATRICE 600 PRO User Manual Follow Mode The gimbal’s orientation is aligned with the aircraft’s nose. One user alone can control the pitch motion of the gimbal, but a second operator is required to control the yaw motion using a second remote controller. FPV Mode The gimbal will lock to the movement of the aircraft to provide a FirstPerson-View flying experience. Free Mode The gimbal’s motion is independent of the aircraft’s orientation.
MATRICE 600 PRO User Manual CMOS Sony EXMOR 1/2.3” 20 mm (35 mm format equivalent), f/2.8, focus at ∞ Lens 9 elements in 9 groups Anti-distortion Single shot Still Photography Modes Burst mode: 3/5/7 frames Auto Exposure Bracketing (AEB): 3/5 frames at ±0.
This content is subject to change. Download the latest version from http://www.dji.com/matrice600-pro If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. MATRICE is a trademark of DJI. Copyright © 2017 DJI All Rights Reserved.
MATRICE 600 PRO Quick Start Guide V1.
Matrice 600 Pro The MATRICETM 600 Pro is equipped with a dedicated DJITM A3 Pro triple-modular redundancy system and advanced intelligent flight functions, ensuring safe and stable operation at all times. With six Intelligent Flight Batteries, the Matrice 600 Pro has 32 minutes of hover time*. Its mechanical design, with quick-release landing gear and mounted folding arms, make it easy to transport, store, and prepare for flight.
Remote Controller The maximum transmission distance of the Matrice 600 Pro remote controller is 16,400 feet (5 km)*. The built-in LiPo battery powers the device for up to four hours* in between charges. An ergonomic design puts gimbal (optional) control functions within comfortable reach, crucial when operating the aircraft. Important controls such as raising and lowering the landing gear and activating the Return-to-Home procedure can also be triggered with a tap of a button.
Using Matrice 600 Pro 1. Download DJI Assistant 2 and the DJI GO App Download and install DJI ASSISTANTTM 2 on your computer via the website link below: http://www.dji.com/matrice600-pro Search ‘DJI GO’ in the App Store or Google Play, and download the app to your mobile device. DJI GO App DJI Assistant 2 supports Windows 7 (or later) or OS X 10.11 (or later). DJI GO supports iOS 8.0 (or later) or Android 4.1.2 (or later). ● ● 2. Checking Battery Levels ● ● Press once to check the battery level.
5. Preparing the Aircraft Mounting the Landing Gear Note the orientation Note the orientation 1 2 Mounting and Powering On Batteries 1. Make sure all six Intelligent Flight Batteries are fully charged and powered off. Insert the batteries into the battery compartments. 2. Press the Power Button once, then press it again and hold for two seconds. This will power on one of the six batteries, automatically triggering the others.
6. Flight DJI GO App Power on the remote controller Power on the aircraft Launch the DJI GO app and enter Camera View Ready to Go (GPS) Before taking off, ensure the Aircraft Status Bar in the DJI GO app indicates ‘Ready to Go (GPS)’. In the DJI GO App: Auto Takeoff Auto Landing Return-to-Home (RTH) Intelligent Flight Modes The aircraft will take off and hover at an altitude of 4 feet (1.2 meters). The aircraft will land vertically and stop its motors. Bring the aircraft back to the Home Point.
Specifications Aircraft Diagonal Wheelbase Dimensions ● Retractable Landing Gear Operating Temperature 1133 mm 1668 mm × 1518 mm × 727 mm with propellers, frame arms and GPS mount unfolded (including landing gear) 437 mm × 402 mm × 553 mm with propellers, frame arms and GPS mount folded (excluding landing gear) 9.5 kg 10 kg 15.5 kg Vertical: ±0.5 m, Horizontal: ±1.
MATRICE 600 PRO www.dji.
MATRICE 600 PRO In the Box Lieferumfang Contenido del embalaje Contenu de l'emballage Contenuto della confezione In de doos Incluído na embalagem Комплект поставки
EN Check that all of the following standard items are in your package. If any item is missing, please contact DJI or your local dealer. DE Überprüfen Sie, ob alle Standardteile im Paket enthalten sind. Falls eines oder mehrere Teile fehlen, wenden Sie sich bitte an Ihren Ansprechpartner bei DJI oder Ihren örtlichen Händler. ES Compruebe que todos los siguientes componentes estándar se encuentran en el paquete. Si falta alguno de ellos, póngase en contacto con DJI o con el distribuidor local.
Standard Package Standardpaket ×1 ×2 Aircraft Body (With Arm Sleeves) Basisgerät (Mit Trägerhülsen) Fuselaje de la aeronave (con fundas para los brazos) Corps de l'appareil (avec bagues de bras) Corpo del velivolo (con manicotti dei bracci) Dronechassis (met armhulzen) Corpo da aeronave (Com mangas dos braços) Корпус дрона (с лучами) Landing Gear Leg Landegestellstreben Pata del tren de aterrizaje Pied de train d'atterrissage Gamba del carrello di atterraggio Poot van het landingsgestel Perna do trem de
×1 Inner Foam Case Innere Schaumstoffeinlage Caja interior de espuma Étui intérieur en mousse Scatola interna in schiuma Binnenste schuimdoos Estojo interior em espuma Пенопластовый ящик ×1 Power Cable Netzkabel Cable de alimentación Câble d'alimentation Cavo di alimentazione Voedingskabel Cabo de alimentação Провод питания ×2 RC Charging Cable Ladekabel für Fernbedienung Cable de carga del control remoto Câble de recharge RC Cavo di ricarica RC RC-oplaadkabel Cabo de carregamento do telecomando Кабель
Manuals · · · · In the Box Disclaimer and Safety Guidelines Intelligent Flight Battery Safety Guidelines Quick Start Guide Produktdokumentation · · · · Lieferumfang Haftungsausschluss und Sicherheitsvorschriften Sicherheitsvorschriften zur Intelligent Flight Battery Kurzanleitung Manuales · · · · Contenido del embalaje Renuncia de responsabilidad y directrices de seguridad Directrices de seguridad de la Batería de Vuelo Inteligente Guía de inicio rápido Guides · · · · Contenu de l'emballage Clause d'
Optional Items Zubehör Elementos opcionales Composants en option Componenti opzionali Optionale items Itens opcionais Дополнительные компоненты D-RTK High-Precision Positioning System D-RTK PräzisionsPositionsbestimmungssystem Sistema de posicionamiento de alta precisión D-RTK Système de positionnement haute précision D-RTK Sistema di posizionamento di alta precisione D-RTK D-RTK high-precision positioneringssysteem Sistema de posicionamento de alta precisão D-RTK Система высокоточного позиционирования D-R
MATRICE 600 SERIES INTELLIGENT FLIGHT BATTERY Safety Guidelines V1.0 2016.
NOTICE This document applies to the following models of Intelligent Flight Battery: TB47S and TB48S. All instructions and other collateral documents are subject to change at the sole discretion of SZ DJI TECHNOLOGY CO., LTD. For up-todate product information, visit http://www.dji.com and click on the product page for this product.
10. DO NOT use the battery if it was involved in a crash or heavy impact. 11. If the battery falls into water with the aircraft during flight, take it out immediately and put it in a safe and open area. Maintain a safe distance from the battery until it is completely dry. Never use the battery again, and dispose of the battery properly as described in the Battery Disposal section below. DO NOT heat batteries. Put out any battery fire using sand or a dry powder fire extinguisher. 12.
Factors that Reduce Battery Cell Life 1. 2. 3. 4. Over-discharging may damage the battery cells. Battery cell temperature exceeds 70℃ or falls below -10℃. Battery is unused for extended periods. Storage temperature exceeds 60℃. Battery Use 1. Make sure all the batteries are fully charged before each flight. 2. You must load all six battery compartments with batteries of the same model before each flight. 3. Land the aircraft immediately when the low battery level warning activates in the DJI GO app.
MATRICE 600 PRO DISCLAIMER AND SAFETY GUIDELINES V1.6 2017.
Searching for Keywords Search for keywords such as “battery” and “install” to find a topic. If you are using Adobe Acrobat Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to begin a search. Navigating to a Topic View a complete list of topics in the table of contents. Click on a topic to navigate to that section. Printing this Document This document supports high resolution printing.
Contents Safety at a Glance 2 NOTICE 4 Glossary 4 Pre-flight Checklist 4 Disclaimer and Warning 5 Compliance Information 7 FCC Warning Message 7 RF Exposure Information 7 IC RSS Warning 7 NCC Warning Message 7 KCC Warning Message 8 EU Compliance Statement 8 Before You Begin 9 Individual Parts 9 Regarding Genuine and Functional Parts Remote Controller 9 9 Center Frame 10 Frame Arms 10 Retractable Modules 10 Landing Gears 10 Flight Control System 11 Lightbridge 2 Air Sy
Safety at a Glance 1. Environmental Considerations • Always fly at locations that are clear of buildings and other The MATRICETM 600 Pro aircraft is NOT a toy and is not suitable for children under the age of 18. obstacles. • DO NOT fly above or near large crowds. • Avoid flying at altitudes above 400 feet (120 m). • Be very careful when flying 8,202 feet (2,500 m) or more above sea level.
5. Observe Local Laws and Regulations • DO NOT fly inside the No Fly Zones. You can find a detailed list of these areas at http://flysafe.dji.com/ • The DJI No Fly Zone is not a replacement for local government regulations or good judgment. • Avoid flying in areas where rescue teams are actively using the airspace. Fly in Open Areas Strong GPS Signal Maintain VLOS Fly Below 400 feet (120 m) Avoid flying over or near obstacles, crowds, high voltage power lines, trees or bodies of water.
NOTICE All instructions and other collateral documents are subject to change at the sole discretion of SZ DJI TECHNOLOGY CO., LTD. For up-to-date product information, visit http://www.dji.com and click on the Matrice 600 Pro product page.
Disclaimer and Warning This product is NOT a toy and is not suitable for children under the age of 18. Adults should keep the aircraft out of the reach of children and exercise caution when operating this aircraft in the presence of children. While the product adopts advanced technology, inappropriate use of the product could result in personal injury or property damages. Please read the materials associated with the product before your first use of the product.
Limitation of Liability IN NO EVENT WILL THE DJI ENTITIES BE LIABLE TO YOU FOR ANY INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, GOODWILL, OR ANY OTHER INTANGIBLE LOSS) ARISING OUT OF OR RELATING TO YOUR ACCESS TO OR USE OF, OR YOUR INABILITY TO ACCESS OR USE, THE PRODUCT, PRODUCT ACCESSORIES, OR ANY MATERIALS, FLIGHT ENVIRONMENT DATA, WHETHER BASED ON WARRANTY, CONTRACT, TORT (INCLUDING NEGLIGENCE), STATUTE, OR ANY OTHER LEGAL THEORY, AND WHETHER O
Compliance Information FCC Warning Message This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
KCC Warning Message “해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .” “해당 무선설비는 운용 중 전파혼신 가능성이 있음” EU Compliance Statement EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industriestrasse.
Before You Begin The following documents have been produced to help you safely operate and make full use of your Matrice 600 Pro: In the Box Disclaimer and Safety Guidelines Quick Start Guide Intelligent Flight Battery Safety Guidelines User Manual Check to see that you have all of the components listed in the In the Box document. Before assembly, read the Disclaimer and Safety Guidelines . Then prepare for your first flight by using the Quick Start Guide.
6. For the GPS in the remote controller to function properly and the Home Point to be accurate, ensure the DJI logo is facing the sky and keep the remote controller away from any metal objects. 7. Linking is required if you wish to replace your remote controller or receiver or add a new remote controller. Refer to the User Manual for details. 8. Make Sure that you first switch off the aircraft (after it is safe to do so), then switch off the remote controller.
Flight Control System To avoid component malfunction, serious injury, and property damage, observe the following rules: Flight Controller 1. DO NOT attempt to modify the structure of the flight controller. 2. DO NOT change the mounting position and orientation of the flight controller. 3. DO NOT short out the ports on the flight controller. 4. Connect cables in strict accordance with port descriptions. Power Management Unit (PMU) 1. The PMU has an input voltage range of 10.
GPS-Compass Pro To avoid component malfunction, serious injury, and property damage, make sure: 1. GPS-Compass Pro’s collapsible mount is unfolded and the extension rod is securely mounted before each flight. 2. GPS-Compass Pro are securely mounted and the arrows are pointing toward the front of the aircraft. 3. Settings in the DJI ASSISTANTTM 2 are correct. To avoid possible serious injury and property damage, observe the following rule: 1. Land immediately when severe drifting occurs in flight, i.e.
Motors 1. Ensure that the motors are securely mounted and rotating smoothly. 2. DO NOT attempt to modify the structure of the motors. 3. DO NOT touch or let your hands or body come in contact with the motors after flight as they may be hot. To avoid possible serious injury and property damage, observe the following rule: 1. DO NOT block any of the ventilation holes on the motors. Motors 1. Keep the motors free of dust. 2.
Firmware To avoid serious injury to children and animals, observe the following rule: 1. Keep children and animals at a safe distance during any firmware upgrade, system calibration, and parameter setting procedures. 1. For safety, always update the firmware to the latest version when an upgrade notification is shown in the DJI GO app. 2. Firmware upgrade notifications will inform about new firmware upgrades. You are required to read and understand the information shown.
Product Care Storage and Transportation To avoid serious injury to children and animals, observe the following rules: 1. Small parts, such as cables and straps, are dangerous if swallowed. Keep all parts out of reach of children and animals. 2. Remove the Intelligent Flight Batteries during transportation. 3. Remove the gimbal from the aircraft during transportation or when storing for an extended period. 4.
Flight Condition Requirements Weather Conditions and Surrounding Environment The aircraft is designed to operate in good to moderate weather conditions. To avoid collision, serious injury and property damage, observe the following rules: 1. DO NOT use the aircraft in severe weather conditions. These include wind speeds exceeding 8 m/s, snow, rain, smog, heavy wind, hail, lightning, tornadoes or hurricanes. 2.
4. DO NOT drop, launch, fire or otherwise project any dangerous payloads on or at any buildings, persons or animals, or which could cause personal injury or property damage. 1. Make sure you have been sufficiently trained and have contingency plans for emergency situations or for when accidents occur. 2. Make sure you have a flight plan and never fly the aircraft recklessly. 3. Respect the privacy of others when using the camera.
Flight Modes, Functions and Warnings Flight Modes To avoid serious injury and property damage, observe the following rules: 1. DO NOT switch from P-mode to either A-mode or F-mode unless you are sufficiently familiar with the aircraft’s behavior for each flight mode, since disabling GPS may result in being unable to fly the aircraft safely. 2. The aircraft will enter A-mode in the following two instances: a. Passive: When there is weak GPS signal or when the compass experiences interference. b.
Failsafe and Return-to-Home 1. The Return-to-Home feature will NOT work if the GPS signal is insufficient or if GPS is not active. 2. Press the RTH (Return-to-Home) button on the remote controller to bring the aircraft back to the Home Point . DO NOT resort to turning off the remote controller to force the aircraft to return to Home Point. 3. Tall buildings may adversely affect the RTH procedure. Please adjust the aircraft location, altitude and speed while returning home to avoid obstacles. 4.
Compliance with Regulations & No Fly Zones Regulations To avoid non-compliant behavior, serious injury and property damage, observe the following rules: 1. DO NOT operate in the vicinity of manned aircraft, regardless of altitude. (Land immediately if necessary) 2. DO NOT fly the aircraft in densely populated areas, including cities, sporting events, exhibitions, performances, etc. 3. DO NOT fly the aircraft above the authorized altitude.
No Fly Zones DJI always stresses safety during flight, and has therefore developed various aids to help users comply with local rules and regulations while flying. We strongly recommend that you update the firmware to the latest version to ensure the following features are fully updated: No Fly Zones 1. No Fly Zones include but are not limited to major airports around world, borders between two sovereign countries or regions, major cities/regions, etc. 2.
DJI Support http://www.dji.com/support This content is subject to change. Download the latest version from http://www.dji.com/matrice600-pro If you have any questions about this document, please contact DJI by sending an email to DocSupport@dji.com. MATRICE is a trademark of DJI. Copyright © 2017 DJI All Rights Reserved. YC.BZ.S01047.06 Printed in China.
DJI/Customer service 1 (818) 235-0789 https://www.dji.
Additional charges may apply outside DJI’s normal service areas. Please contact DJI for information specific to your location What to do Before Obtaining After-sales Service Before obtaining after-sales service, the following steps must be taken: √ Follow the procedures specified by DJI. √ Backup all data contained on your product’s SD card. √ Except for flight logs, remove all data, including confidential information, proprietary information and personal information, from the product.
If you obtain service under this policy, you authorize DJI to store, use, and process your flight log information and your contact information, including name, phone numbers, address, and email address. DJI may use this information to perform service under this policy. We may contact you to inquire about your satisfaction with our service or to notify you about any product recalls or safety issues.
When receiving service, DJI is responsible for loss or damage to your product only while it is in DJI's possession or in transit, if DJI is responsible for transportation. DJI is NOT responsible for loss or disclosure of any data, including confidential information, proprietary information, or personal information, contained in a product.
