Owner's Manual

1
Safety at a Glance
Please read this entire document and visit http://www.dji.com/action-2 to view the user manual, other documents, and the
tutorial videos with the most current instructions and warnings. Failure to read and follow instructions and warnings may
result in personal injury, damage to your DJI OSMO
TM
product, or other objects in the vicinity. This document and all other
collateral documents are subject to change at the sole discretion of DJI OSMO.
By using this product, you hereby signify that you have read and agreed to abide by the terms and conditions of
this document. You agree that you are solely responsible for your own conduct while using this product and for any
consequences thereof. This product is not intended for use by children without direct adult supervision.
1. DJI Action
TM
2 contains magnets. Keep the camera unit away from magcards, IC cards, hard disks, RAM chips, implantable medical
devices such as pacemakers, and other devices to avoid interference.
2. All the holes on the camera unit have built-in waterproof material. DO NOT poke the holes. Clean the camera unit with a clean, dry
cloth after using under water.
3. DO NOT attach the camera unit to the front touchscreen module when there is any dust or water on the expansion ports. Otherwise,
the camera unit may corrode or short-circuit.
4. Put out any product re using water, sand, re blanket, or a dry powder re extinguisher.
5. The product should be used in temperatures from 0º to 40º C (32° to 104° F). Use of the product in environments above 40º C (104° F)
can lead to a re or explosion. Use of the product below 0º C (32° F) can lead to permanent damage.
6. Never disassemble or pierce the product in any way or the battery may leak, catch re, or explode.
7. DO NOT drop or strike the product. DO NOT place heavy objects on the product.
8. DO NOT heat the product. DO NOT put the product in a microwave oven or in a pressurized container.
9. DO NOT leave the product near heat sources such as a furnace or heater. DO NOT leave the product inside of a vehicle on hot days.
The ideal storage temperature is 22º C to 28º C (72° to 82° F).
10. DO NOT store the product fully discharged for an extended period. Otherwise, it will over discharge, which will lead to permanent
damage.
1. Intricate components inside DJI Action 2 may be damaged upon impact and cause the camera unit to malfunction.
2. Keep the lens glass clean. Sand and dust may damage the lens glass. Clean DJI Action 2 with a clean, dry cloth.
3. Make sure to be careful if the lens glass breaks.
4. Keep DJI Action 2 away from sand and dust. Wash the camera unit if the holes are blocked by sand, dust, or any other substance.
5. DO NOT poke the USB-C port or microSD card slot
6. DO NOT expose DJI Action 2 to extreme cold or hot temperature. Otherwise, the operating time and functionality may be negatively
aected.
7. DO NOT use DJI Action 2 during lightning storms.
8. DO NOT disassemble or repair DJI Action 2 by yourself.
9. DO NOT use DJI Action 2 inside hot springs. DO NOT allow DJI Action 2 to come into contact with corrosive or unknown liquids.
10. When attaching DJI Action 2 to the roof or window of a car, the camera unit may fall o if the car travels too fast, the surface is not clean,
or there is bad weather such as high winds or a thunderstorm.
11. The front touchscreen module is not waterproof. The waterproof case is required when using the front touchscreen module with the
camera unit under water.
12. Charge DJI Action 2 when the battery level is low. Storing the camera unit for more than four months with low battery will reduce the battery life.
Specications
Model MC211
Wi-Fi
Operating Frequency 2.400-2.4835 GHz, 5.150-5.250 GHz, 5.725-5.850 GHz
Transmitter Power (EIRP)
2.4 GHz:
<
16 dBm (FCC/CE/SRRC/MIC)
5.1 GHz:
<
14 dBm (FCC/CE/SRRC/MIC)
5.8 GHz:
<
14 dBm (FCC/CE/SRRC)
Protocol 802.11a/b/g/n/ac
Bluetooth
Operating Frequency 2.400-2.4835 GHz
Transmitter Power (EIRP)
<
4 dBm
Protocol BLE 5.0
Operating Temperature 0° to 40° C
EN