IMPORTANT The Dixon ZTR mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operator's manual carefully, and become completely familiar with the controls. Your Dixon dealer will gladly provide a checkout ride, and answer any questions. READ CAREFULLY You have purchased a top quality lawn mower that has been carefully inspected and adjusted at the factory.
SERIAL NUMBERS The lawn mower has three serial numbers: Mower Number — Located on frame at right rear transaxle mount. Transaxle Number — Located on transaxle. Engine Number — Located on engine. When referring to serial number on Warranty Registration, etc., use Mower Serial Number located on frame. SAFETY INSTRUCTIONS BEFORE MOWING 1. Read these safety instructions and engine manufacturer's operating and maintenance instructions that are furnished with the mower. 2.
IMPORTANT OPERATING INSTRUCTIONS Dixon ZTR mowers offer a new concept in mowing, providing unique maneuverability and ease. The following procedures will allow one to become familiar with the unique method of control very easily. 1. SET PARKING BRAKE — Be sure that drive levers are free and in the neutral position. (When drive levers are released, they should return to neutral position.) 2. "Blade Operation" lever is to be set in the "Disengage" position. 3. Move throttle control to "Choke" position. 4.
ALWAYS DISENGAGE BLADE OPERATION BEFORE DISMOUNTING. 9. Parking Brake: Parking brake is on right hand side of floor area and is engaged by pushing full forward with foot. To disengage, pull lever back toward operator by hand. In emergency situations, brake may be used in conjunction with the natural braking of the transaxle by applying pressure with foot. Always set parking brake before dismounting. Be sure that parking brake is disengaged before moving.
BODY REMOVAL A. ZTR-424 Body Removal 1. Disconnect throttle cable from engine. 2. Disconnect key switch wire loom from frame wire loom at front of body. 3. Disconnect seat switch wire loom from frame wire loom. This connection is located approximately level with the back of the seat on left hand side of frame under the body. 4. Remove four control lever bolts and remove upper control levers. 5. Remove engaging handle by removing bolt and nut under handle. - 6.
ELECTRICAL SYSTEMS Keep all connections clean and tight. Maintain the fluid in the battery at correct level. BODY The body may be washed with a mild detergent and waxed with any automotive type wax. TRANSAXLE For adjustment or repair confer with authorized Dixon dealer service department. Adjustment or repair by other than authorized dealer voids warranty. SPARE PARTS See your dealer for ordering spare parts or warranty service. INSTALLING AND REMOVING MOWER DECK FROM FRAME 1.
TRANSAXLE ASSEMBLY 5000-102
TRANSAXLE ASSEMBLY 5000
PARTS LIST FOR 42" MODELS Part No. Name 1000C 1015 1020 1022 1022A 1039 1040 1501R 1501L 1502 1503 1504 1506 1507-1 1509 1513 1535 1536 1539 1540 1543 1544 1552 1560-1 1564 1574 1579 1580 1581 1591 1606 1607 1624 Part No. Name 1629 Bumper Weldment 1635 Double Engine Pulley Frame Weldment 1636 Bellcrank Kit Caster Weldment 1638 Lower Control Lever Assembly Caster Axle 1640 Tension Plate 11 h.p.
Part No.
OWNER INFORMATION Date Mower Purchased___________________Mower Model Number ___________________ Mower Purchased from ________________________________________________________ dealer name & address Mower Serial Number_____________________Transaxle Serial Number _________________ Oil changed this date: 1. ____________________________ 4. ____________________________ 2. ______________________________ 5. ______________________________ 3. ______________________________ 6.
Form No. 4089-1279 Litho in U.S.A. ® DIXON and ZTR are registered trademarks of Dixon Industries, Inc.
