Spee di th d wi ce el is prod ann u Ch 0 re n rg y 10 % n e w a ble e e SpeediChannel ™ System Installation
Contents Introduction 3 DiversiTech Speedichannel™ System 4 Features and Benefits System Installation 6 Step 1 7 Step 2 8 Step 3 9 Step 4 10 Step 5 11 Step 6 Installation Diagrams 12 14 16 17 Indoor and Outdoor installations Flex Joint and Drain Hose diagrams Line Set configuration Air Handler installations Sizing Chart 21 Dimensions and Capacities Technical Information 22 General data and safety information Mini Component Guide 23 Product information and product layout 2 DiversiTech SpeediChannel™
I N T R O D U C T I O N 4 Features and Benefits Features and Benefits • SpeediClip™ simply slides into place on a railing molded into the inside of the SpeediChannel™ allowing for single person installation. Competitive products must be screwed in place which is extremely time consuming. Single piece wall sleeve • Competitive products are multi-part which is cumbersome. 20mm drain line with double connections • Versatile — fits 16, 18, or 20mm drain line.
S Y S T E M I N S T A L L A T I O N 6 Step 1 Step 2 Attach the SpeediChannel™ base to the wall about every 15 inches with screws suitable for the wall construction (siding, stucco, brick, etc.). Screw through the center of the molded rail. Slide the connecting piece (elbow, union, tee, etc.) under the SpeediChannel™ before attaching the end of the channel to the wall.
S Y S T E M Step 3 Step 4 Install the line set, drain line, and wires inside the SpeediChannel™. Test the equipment installation prior to tightening the cable ties. Tighten the cable ties snug, but not so tight they damage the tubing insulation or kink the drain line. Trim excess length from the cable tie. Attach the SpeediChannel™ to the base.
S Y S T E M Step 5 Step 6 Attach the fitting covers with the screws provided. When complete, paint the SpeediChannel™ to match surface of installation (if desired).
I N S T A L L A T I O N Typical Detail of Indoor Installation A Typical Detail of Outdoor Installation B A H C D I A G R A M S D I A G R A M S C E I N S T A L L A T I O N D A C 12 A F 13
I N S T A L L A T I O N A D I A G R A M S I N S T A L L A T I O N D I A G R A M S G A 14 Typical Detail of Cut-out for Drain Hose Typical Detail of Flex Joint Application Notch bottom half as shown here.
I N S T A L L A T I O N I N S T A L L A T I O N Basic Application - 1 Air Handler Typical Line Set, Cable, and Drain Hose Configuration C A B Drain Hose A D I A G Insulated R Refrigerant Line A M S J SpeediChannel™ Top A D I A G R A M S SpeediChannel™ Bottom SpeediClip™ 16 K 17
I N S T A L L A T I O N D I A G R A M S Horizontal Dual Air Handler System Application Vertical Dual Air Handler System Application C C A L A A J J A K 18 C A A I N S T A L L A T I O N D I A G R A M S K 19
I N S T A L L A T I O N D I A G R A M S Building with Different Wall Thickness Application Sizing Chart and Selection Information Maximum Line Set, Drain Pipe, and Cable Capacity using 3/8” Insulation D Model 2 Dimensions Length 30-D32 3” x 2-1/2” 78” 30-D42 4” x 2-3/4” 78” 30-D6 6” x 3” 78” A E Mini Split Systems – Liquid and Suction Line with 3/8” Insulation A Liquid Line Suction Line Drain Hose Power Cable Control Cable Nominal Tonnage 3/8” 5/8” 3/4” OD 1 x UF 14-3 1 Pair 18 AWG 1–3 Tons 2
T E C H N I C A L S P E C I F I C A T I O N S Technical Data SpeediChannel™ CATALOG NO. 2 30-D3 2 30-D4 2 30-D6 Color Size Material Fire Rating Temperature Range Weather Resistance Fixing Screws Natural 230-D3: 3” x 2-1/2” OD 230-D4: 4” x 2-3/4” OD 230-D6: 6” x 3-1/8” OD Weather Resistant PVC, UV Stabilized and Fire Resistant Meets UL 94V.-0 4˚F TO 140˚F Tested to over 2,000 hours Stainless Steel Standard Length: 78” DESCRIPTION QTY.
M I N I C O M P O N E N T G U I D E 90º Inside Elbow CATALOG NO. 2 30-EB3 2 30-EB4 2 30-EB6 DESCRIPTION Flex Joint QTY. NEEDED 3” 90 degree Inside Elbow 4” 90 degree Inside Elbow 6” 90 degree Inside Elbow 2 30-EIN3 2 30-EIN4 2 30-EIN6 DESCRIPTION QTY. NEEDED 3” 90 degree Outside Elbow 4” 90 degree Outside Elbow 6” 90 degree Outside Elbow 3” Flex Joint 4” Flex Joint QTY. NEEDED CATALOG NO. DESCRIPTION 230-DE3 230-DE4 230-DE6 3” Duct End 4” Duct End 6” Duct End QTY.
M I N I C O M P O N E N T G U I D E Mounting Blocks CATALOG NO. 230-MB14W 230-MB17W 230-MB36W 230-MBCW DESCRIPTION QTY. NEEDED 14” MountBlock (White) pack of 2 17” MountBlock (White) pack of 2 36” MountBlock (White) pack of 2 MountBlock End Cap (White) pack of 4 CladLite® Equipment Pads CATALOG NO. 1636-2 1636-3 DESCRIPTION QTY. NEEDED 16” x 36” x 2” CladLite® Equipment Pad 16” x 36” x 3” CladLite® Equipment Pad Condensate Drain Pans CATALOG NO.
About DiversiTech 6650 Sugarloaf Parkway Duluth, GA 30097 678.542.3600 800.995.2222 678.542.3700 Fax DiversiTech Corporation is North America’s largest manufacturer of equipment pads and a leading manufacturer and supplier of components and related products for the heating, ventilating, air conditioning, and refrigeration (HVACR) industry.
