Display Elektronik GmbH OLED-MODULE DEP 128064A-W 1,5“ - OLED Product Specification Ver.: 2 03.12.
DEP 128064A-W Production Specification Revision History VERSION DATE 0 28.09.2014 First Release 1 12.12.2014 Modify ICC Modify Brightness 2 03.12.2015 Modify Lifetime Version: 2 REVISED PAGE NO.
DEP 128064A-W Production Specification Contents 1. General Specification 2. Interface Pin Function 3. Counter Drawing & Block Diagram 4. Absolute Maximum Ratings 5. Electrical Characteristics 6. Optical Characteristics 7. OLED Lifetime 8. Reliability 9. Inspection specification 10.
DEP 128064A-W Production Specification 1. General Specification The Features is described as follow: n Module Dimension: 45.24 × 29.14 × 2.05 mm n Active Area: 35.06 × 17.52 mm n Dot Matrix: 128 x 64 Dots n Dot Size: 0.258 × 0.258 mm n Dot Pitch: 0.274 × 0.
DEP 128064A-W Production Specification 2. Interface Pin Function Pin No. Symbol Function 1 2 3 4 5 6 Reserved Pin (Supporting Pin) The supporting pins can reduce the influences from stresses NC(GND) on the function pins. These pins must be connected to external ground. Ground of Analog Circuit VLSS This is an analog ground pin. It should be connected to VSS externally. Ground of Logic Circuit VSS This is a ground pin. It also acts as a reference for the logic pins.
DEP 128064A-W 11 12 13~20 21 22 23 24 Version: 2 Production Specification Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for R/W# read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
DEP 128064A-W Production Specification 3.
DEP 128064A-W FUNCTION BLOCK DIAGRAM Production Specification *For more information, please refer to Application Note.
DEP 128064A-W Production Specification 4. Absolute Maximum Ratings Parameter Symbol Min Max Unit Notes Supply Voltage for Logic VDD -0.3 4 V 1, 2 Supply Voltage for Display VCC 0 15 V 1, 2 Operating Temperature TOP -40 +80 °C - TSTG -40 +80 °C - Storage Temperature Note 1: All the above voltages are on the basis of “VSS = 0V”. Note 2: When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur.
DEP 128064A-W Production Specification 5. Electrical Characteristics Item Symbol Condition Min Typ Max Unit Supply Voltage for Logic VDD － 2.8 3.0 3.3 V Supply Voltage for Display VCC － 10 12 15 V High Level Input Low Level Input High Level Output Low Level Output 50% Check Board operating Current VIH VIL VOH VOL － － － － 0.8×VDD 0 0.9×VDD 0 － － － － VDD 0.2×VDD VDD 0.
DEP 128064A-W Production Specification 6. Optical Characteristics Item View Angle Contrast Ratio Response Time Symbol Condition Min Typ Max Unit (V)θ － 160 － － deg (H)φ － 160 － － deg CR Dark 2000:1 － － T rise － － 10 － μs T fall － － 10 － μs 70 90 － cd/m2 Display with 50% check Board Brightness CIEx(White) (CIE1931) 0.26 0.28 0.30 － CIEy(White) (CIE1931) 0.30 0.32 0.
DEP 128064A-W Production Specification 7. OLED Lifetime ITEM Operating Life Time Conditions Ta=25°C / Initial 50% check Board Typical Brightness Value Min Typ Remark 20,000 Hrs - Note Note: 1. Life time is defined the amount of time when the luminance has decayed to <50% of the initial value. 2. This analysis method uses life data obtained under accelerated conditions to extrapolate an estimated probability density function (pdf) for the product under normal use conditions. 3.
DEP 128064A-W Production Specification 8. Reliability Content of Reliability Test Environmental Test Test Item High Temperature storage Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature/ Humidity Storage Temperature Cycle Content of Test Test Condition Applicable Standard Endurance test applying the high storage temperature for a long time. 80°C 240hrs —— Endurance test applying the low storage -40°C temperature for a long time.
DEP 128064A-W Production Specification Test and measurement conditions 1. All measurements shall not be started until the specimens attain to temperature stability. After the completion of the described reliability test, the samples were left at room temperature for 2 hrs prior to conducting the failure test at 23±5°C; 55±15% RH. 2. All-pixels-on is used as operation test pattern. 3.
DEP 128064A-W Production Specification 9. Inspection specification NO 01 02 03 04 Item Electrical Testing Black or white spots on OLED (display only) OLED black spots, white spots, contamina tion (non-displ ay) Polarizer bubbles Version: 2 Criterion 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character, dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.5 Current consumption exceeds product specifications. 1.6 OLED viewing angle defect. 1.
DEP 128064A-W NO 05 Item Scratches Production Specification Criterion Follow NO.3 OLED black spots, white spots, contamination Symbols Define: x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: OLED side length L: Electrode pad length: AQL 6.1 General glass chip : 6.1.
DEP 128064A-W NO Item Production Specification Criterion Symbols : x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: OLED side length L: Electrode pad length 6.2 Protrusion over terminal : 6.2.1 Chip on electrode pad : y: Chip width x: Chip length y≦0.5mm x≦1/8a 6.2.2 Non-conductive portion: 06 AQL z: Chip thickness 0 ＜ z≦t Glass crack 2.
DEP 128064A-W NO 07 08 09 10 11 Item Cracked glass Backlight elements Production Specification Criterion AQL The OLED with extensive crack is not acceptable. 2.5 8.1 Illumination source flickers when lit. 8.2 Spots or scratched that appear when lit must be judged. Using OLED spot, lines and contamination standards. 8.3 Backlight doesn’t light or color wrong. 0.65 2.5 0.65 Bezel 9.1 Bezel may not have rust, be deformed or have fingerprints, stains or other contamination. 9.
DEP 128064A-W NO 12 Production Specification Item Criterion AQL 2.5 General appearance 12.1 No oxidation, contamination, curves or, bends on interface Pin (OLB) of TCP. 12.2 No cracks on interface pin (OLB) of TCP. 12.3 No contamination, solder residue or solder balls on product. 12.4 The IC on the TCP may not be damaged, circuits. 12.5 The uppermost edge of the protective strip on the interface pin must be present or look as if it cause the interface pin to sever. 12.
DEP 128064A-W Production Specification Check Item Classification No Display Major Criteria Missing Line Major Pixel Short Major Darker Short Major Wrong Display Major Un-uniform B/A x 100% < 70% A/C x 100% < 70% Major Version: 2 PAGE: 20
DEP 128064A-W Production Specification 10. Precautions in use of OLED Modules (1) Avoid applying excessive shocks to module or making any alterations or modifications to it. (2) Don’t make extra holes on the printed circuit board, modify its shape or change the components of OLED display module. (3) Don’t disassemble the OLED display module. (4) Don’t operate it above the absolute maximum rating. (5) Don’t drop, bend or twist OLED display module. (6) Soldering: only to the I/O terminals.
DEP 128064A-W Production Specification (7) Do not apply stress to the LSI chips and the surrounding molded sections. (8) Do not disassemble nor modify the OLED display module. (9) Do not apply input signals while the logic power is off. (10) Pay sufficient attention to the working environments when handing OLED display modules to prevent occurrence of element breakage accidents by static electricity. * Be sure to make human body grounding when handling OLED display modules.
DEP 128064A-W Production Specification 10.3 Designing Precautions (1) The absolute maximum ratings are the ratings which cannot be exceeded for OLED display module, and if these values are exceeded, panel damage may be happen. (2) To prevent occurrence of malfunctioning by noise, pay attention to satisfy the VIL and VIH specifications and, at the same time, to make the signal line cable as short as possible. (3) We recommend you to install excess current preventive unit (fuses, etc.
