Display Elektronik GmbH TFT MODULE DEM 800480Q TMH-PW-N 5,0“ TFT Product Specification Ver.: 0 17.06.
DEM 800480Q TMH-PW-N Production Specification Revision History Version: 0 VERSION DATE REVISED PAGE NO. Note 0 17.06.
DEM 800480Q TMH-PW-N Production Specification Contents 1. General Specification 2. Interface 3. Contour Drawing 4. Absolute Maximum Ratings 5. Electrical Characteristics 6. Optical Characteristics 7.
DEM 800480Q TMH-PW-N Production Specification 1. General Specifications n Size: 5.0 Inch n Dot Matrix: 800 x (RGB) x 480 dots n Module Dimension: 120.70 x 75.80 x 2.90 mm n Active Area: 108.00 x 64.80 mm n Dot Pitch: 0.045 x 0.
DEM 800480Q TMH-PW-N Production Specification 2. Interface 2.1. LCM PIN Definition FPC connector is used for electronics interface. The recommended model is FH19SC-40S-0.5SH (05) manufactured by HIROSE. I/O No.
DEM 800480Q TMH-PW-N 37 38 39 40 NC NC NC NC - Production Specification No connect No connect No connect No connect Note: I: input, O: output t, P: Power 3.
DEM 800480Q TMH-PW-N Production Specification 4. Absolute Maximum Ratings Item Symbol Min Typ Max Unit Operating Temperature TOP -20 － +70 °C Storage Temperature TST -30 － +80 °C Alloeable Forward Current IF(mA) Note: Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above 1. Temp. ≦60°C, 90% RH MAX. Temp.＞60°C, Absolute Humidity shall be less than 90% RH at 60°C Version: 0 Ambient Tem.
DEM 800480Q TMH-PW-N Production Specification 5. Electrical Characteristics 5.1. Typical Operation Conditions Item Symbol Values Min. Typ Max. Unit Remark Note 2 Power Voltage VDD 3.0 3.3 3.6 V Current for Driver IVDD - 17 25 mA Input Logic High Voltage VIH 0.8 VDD - VDD V Input Logic Low Voltage VIL 0 - 0.2 VDD V 5.2. Backlight Driving Conditions (12 White Chips) Parameter Symbol Min. Typ. Supply Voltage of White VL 17.4 19.
DEM 800480Q TMH-PW-N Production Specification 5.3. Power Sequence To prevent the device damage from latch up, the power ON/OFF sequence shown below must be followed. Power ON: VDD, DGND_ VDDA, AGND _ V1 to V14 Power OFF: V1 to V14 _ VDDA, AGND_ VDD, DGND In order to prevent ILI6122 from power ON reset fail, the rising time (tPOR) of the digital power supply VDD should be maintained within given specifications.
DEM 800480Q TMH-PW-N Production Specification 5.4.
DEM 800480Q TMH-PW-N Production Specification Input Clock and Data Timing Diagram Version: 0 PAGE: 11
DEM 800480Q TMH-PW-N Production Specification Timing Horizontal Input Timing Parameter Symbol Horizontal display area CLKIN frequency Max. Unit 33.3 1056 1200 CLKIN -- 1 -- CLKIN -- -- -- CLKIN -- 40 -- CLKIN -862 tHPW Max. CLKIN fCLK Min. Typ. 800 -50 -- tH Typ. Min.
DEM 800480Q TMH-PW-N Production Specification Data Input Format Version: 0 PAGE: 13
DEM 800480Q TMH-PW-N Production Specification 6. Optical Characteristics Item Symbol Response Time Tr Tf Contrast Ratio CR Color Wx Chromaticity White Hor. Viewing Angle Ver. Brightness Wy Condition. θ=0°、Φ=0° ΦT - Typ. Max. 10 viewing angle θ=0°、Φ=0 CR≧10 ΦB - - Unit 20 .ms - 10 20 .ms 500 700 - - At optimized ΘR ΘL Min 0.26 0.31 0.36 0.28 0.33 60 70 0.38 - 60 70 - 40 50 - 60 70 - 450 - 400 Remark Note 3,5 Note 4,5 Note 2,6,7 Deg.
DEM 800480Q TMH-PW-N Production Specification Fig. 6.2. Optical measurement system setup Note 3: Definition of Response time: The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time, Tr, is the time between photo detector output intensity changed from 90%to 10%.
DEM 800480Q TMH-PW-N Production Specification 7. Reliability Content of Reliability Test (Wide temperature, -20°C~70°C) Environmental Test Test Item High Temperature storage Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature/ Humidity Operation Thermal shock resistance Content of Test Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time.
