QUICK REFERENCE Lift to answer or make a call Handset Cord Plug coiled handset cord into this jack The Receiving Call Light will flash when receiving a call Press to dial a telephone number Press to mute the handset so the caller cannot hear you; release to un-mute.
QUICK REFERENCE (CONTINUED) 1. Set the RINGER switch to the ON position to have the ringer sound when receiving a phone call. 2. Set the Tone/Pulse switch to Tone or Pulse to match the service provided on your telephone line. 3. Connect the coiled handset cord to the base. 4. Connect the straight cord to the telephone base jack and telephone wall jack. 5. When the phone rings, lift the handset and speak into the mouthpiece. Hang up when call is completed. 6. Lift the handset and listen for a dial tone.
PACKAGE LIST The package should include the following items: 1. Base Unit 2. Handset with Handset Cord 3. Telephone Line Cord 4. User's Guide IMPORTANT SAFETY INSTRUCTIONS Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED) When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on this product. 3. Do not use this product near water–for example: near a bathtub, wash bowl, kitchen sink or laundry tub; in a wet basement; or near a swimming pool. 4.
LOCATION OF CONTROLS FRONT 1 2 3 4 5 6 1. 2. 3. 4. 5. 7 8 Handset Handset In Jack Handset Coiled Cord Key Buttons (0–9,#,*) MUTE Button 6. 7. 8. 9.
LOCATION OF CONTROLS (CONTINUED) BOTTOM 1 4 2 5 6 3 1. 2. 3. 4. 5. 6.
INSTALLATION This unit can be used on a desk, or other level surface away from excessive heat or direct sunlight. Desk or Table Use 1. Set the RINGER switch to the ON position to have the ringer sound when receiving a phone call. Insert batteries as described on the next page to hear the Disney ring when receiving a call. 2. Set the Tone/Pulse switch to Tone or Pulse to match the service provided on your telephone line. If you are not sure of your service, please contact your telephone company. 3.
INSTALLATION (CONTINUED) Battery Installation To hear the Disney ring when receiving a call, insert three (3) AAA size batteries into the bottom of the unit as described below. NOTE: When the batteries become weak, the unit will revert back to the standard ring. 1. Remove the Battery Compartment screw. 2. Press in on the Battery Compartment tab and lift off the Battery Compartment cover. 3. Insert three (3) AAA size batteries, observing the polarity as shown. 4.
TELEPHONE OPERATION RECEIVING CALLS MAKING CALLS 1 1 Make sure the RINGER switch is in the ON position. When the phone rings and the Receiving Call Light flashes, lift the handset and speak into the mouthpiece. Hang up when the call is 1 completed. Lift the handset and listen for a dial tone. Press the 1key buttons (0-9) for the specific number that you wish to call. RINGER SWITCH 1 2 Slide the RINGER switch to the ON position to turn the ringer on.
TELEPHONE OPERATION T/P (TONE/PULSE) SWITCH REDIAL BUTTON 1 1 Slide the T/P switch to Tone (T) or Pulse (P) to match the service provided on your telephone line. If you are not sure of your service, please contact your telephone company. Press the REDIAL button to 1 automatically redial the last number dialed. NOTE: Please note that only the last number you called can be stored in the Redial memory.
TROUBLESHOOTING GUIDE Before requesting service, please refer to the following chart and check for the symptom you are experiencing. PROBLEM: No Dial Tone SOLUTION 1: Handset cord is not connected properly; securely connect to the base. SOLUTION 2: Line cord is not connected properly; securely connect to wall telephone outlet and Line In jack on the bottom of the unit. SOLUTION 3: Your phone line is having problems; call the phone company. PROBLEM: Ringer not working or not working properly.
For additional set-up or operating assistance, please visit our website at www.disneyelectronics.com or contact customer service at (954) 660-7026. Please keep all packaging material for at least 90 days in case you need to return this product to your place of purchase or Memcorp. For parts and accessories, contact Fox International at 1-800-321-6993. Distributed by Memcorp Inc., Weston, FL, Disney Elements © Disney 2004.
