EN User Manual Dishwasher DSF6106W DSF6106X
Contents Safety information Safety instructions Control panel Programs Before first use Daily use 2 3 4 5 5 6 Hints and tips Care and cleaning Troubleshooting Technical information Warranty 9 10 11 12 12 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages.
• • • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or a similarly qualified persons in order to avoid a hazard. Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.
• • • • Do not drink and play with the water in the appliance. Do not remove the dishes from the appliance until the programme is completed. There can be detergent on the dishes. The appliance can release hot steam if you open the door while a programme operates. Do not put flammable products or items that are wet with flammable products in, near or on the appliance. Service • Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts.
Indicator Description Rinse aid indicator. It is always off while the program operates. Half Load indicator. Programs Program Degree of soil Type of load Program phases Consumption values 1) Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 128 0.75 11.7 Normal soil Crockery and cutlery • • • • Prewash Wash 65 °C Rinses Dry 100 - 120 1.2 - 1.
3. Start a program to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. Adding rinse aid 1 43 21 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. Daily use 1. 2. Open the water tap. Set the correct program for the type of load and the degree of soil. Make sure that the appliance is in Program selection mode. • 3. 4. 5.
Program selection mode The appliance must be in Program selection mode to start a program. If the control panel does not show this condition, use the Reset function. Reset With Reset you can cancel the running program . The appliance goes back to the Program selection mode. Starting a program Open the water tap, close the door, select a program, press .
Option Half load 1. Set the program. 2. Press 3. Press the related indicator comes on. to start the program. This option is available with , and . With this option you can wash a small load of tableware and cookware. The option decreases the program duration and the consumption of water and energy. Load both baskets and use less quantity of detergent. Opening the door while the appliance operates If you open the door while a program is running, the appliance stops.
The indicator comes on. If you do not deactivate the appliance within 5 minutes all indicators goes off. This helps to decrease energy consumption. Turn the knob to . Close the tap. For the better drying results keep the appliance door ajar for some minutes before you remove the dishes. Let the dishes cool down before you remove them form the appliance. Hot dishes are easily damaged. Hints and tips General 2.
Unloading the baskets 1. 2. For the better drying results open the door 5-10 cm and allow tableware to cool down for 30-40 min. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. First remove items from the lower basket, then from the upper basket. At the end of the program water can still remain on the sides and on the door of the appliance.
run long duration program at least 2 times per month. Troubleshooting If the appliance does not start or it stops during operation, before you contact the Service, check if you can solve the problem by yourself with the help of the information in the table. Problem and alarm code With some problems different indicators flash intermittently and/or continuously to show an alarm code. Possible solution You cannot activate the appliance. • • Make sure that the mains plug is connected to the mains socket.
Problem Possible solution • The dishes are wet. • • • The program does not have a drying phase or has a drying phase with low temperature. The rinse aid dispenser is empty. The quality of the rinse aid can be the cause. Keep the dishwasher door ajar for some time before removing tableware. Refer to "Hints and tips" for other possible causes.
2. 3. 4. 5.
13. To enquire about claiming under this warranty, please follow these steps: a) carefully check the operating instructions, user manual and the terms of this warranty; b) have the model and serial number of the Appliance available; c) have the proof of purchase (e.g. an invoice) available; d) telephone the numbers shown below. 14. You accept that if you make a warranty claim, Electrolux and its ASC may exchange information in relation to you to enable Electrolux to meet its obligations under this warranty.
www.dishlex.com.
