t Reflex Duplicator Manual t Reflex Duplicator Manual Table of Contents Welcome Before you start Page 2 Page 2 Tutorial Guide I. Make Disc to Disc Copies II. Make Hard Drive (HDD) to Disc Copies III. Select the Duplication Speed IV. Select the Master Reading Source V. Load Master Disc onto the Hard Drive VI. Rename Existing HDD Partition Name VII. Delete HDD Partitions VIII. Change HDD Partition Size IX. Change SETUP settings X. Audio CD Editing XI. Account Management Feature XII.
t Reflex Duplicator Manual 3. Maintenance: It is very important to operate and keep the duplicator in a dust free, clean environment since dust is the number 1 killer for CD/DVD recording devices. Failure to do so may severely damage your duplicator. We strongly suggest you place an Air Cleaner next to the duplicator and constantly use the Air Duster (Can Air) to clear off any dust on the surface of the duplicator.
t Reflex Duplicator Manual t Reflex Duplicator Manual For detail information, please review “Tutorial Guide XII: Introduction to Duplication Mode.“ Reader Port 2.0 DVDR *** The Reader Port could be indexed as 1.0. Either 1.0 or 2.0 is fine. Make sure it is located at the “Reader Port“. If not, then you need to press UP or DOWN navigation button to search for it. c. Press “ENT“ to submit your selection.
t Reflex Duplicator Manual To specify the number of copies for your project, you need to enter/input a 4-digit number. If you are planning to specify a number that is less than 4 digits, please fill the leading spaces with “0“s (any leading “0“ will be skipped). An example of that 4digit number could be “0234“ (Two hundred and thirty four), or “0010“ (ten).
t Reflex Duplicator Manual By default, the “Auto Start“ setting is set to “Auto“. For example, if your duplicator has detected 3 blank discs and didnít detect any additional blank discs within 30 seconds, then the duplication will start automatically. Once the number of blank discs you inserted matches the number of discs detected on the screen. Then press “ENT“ (if you are not using Auto Start or wish to speed up the process) to confirm and the following Processing screen will appear. Processing...
t Reflex Duplicator Manual t Reflex Duplicator Manual Tutorial Guide: If you enabled the counter and the number of discs you have inserted is more than what you requested, you will receive a message regarding you have inserted more discs than what you need. You can continue to copy or you can eject the extras. If you happen to have any failed discs (bad copy), the failed disc(s) will not be ejected automatically.
t Reflex Duplicator Manual t How to make copies from the Hard Drive? When you turn on your duplicator, after it has booted up, you should see the following signifying your duplicator is ready. Disc Makers 1. COPY 1. .99 Make sure the Master Reading Source is set to the Hard Drive. It is very important to make sure the Master Reading Source is set to the Hard Drive in order to avoid unnecessary error messages.
t Reflex Duplicator Manual t partition and press “ENT“ to submit. You will see the following: Edit Partition Name [ ] OK? f. Press “DOWN“ button consecutively until “F“ is displayed. iii. Press “DOWN“ button consecutively until “U“ is displayed. iv. Press “ENT“ button once to move the cursor to the next position. v. Press “DOWN“ button consecutively until “N“ is displayed. vi. Press “ENT“ button once to move the cursor to the next position. - 15 - viii.
t Reflex Duplicator Manual a. Press “ESC“ button to go back to the main menu. You shall see the following: Image 3.2 Load Partition b. Use UP or DOWN arrow button to navigate to the following screen. Disc Makers 1. COPY .99 t Reflex Duplicator Manual c. The Counter Selection Menu will let you to choose how many copies you want to make for your project.
t Reflex Duplicator Manual t Reflex Duplicator Manual “ENT“ once and the cursor is now moved to “OK“. To enter the number, you need to use UP or DOWN button to select the number for each digit and use “ENT“ or “ESC“ button to move the cursor position right or left, once youíve finished, move the cursor to “OK“ and press “ENT“. For example, if I want to specify a counter value of 21 (twenty one). The 4-digit value would be “0021“.
t Reflex Duplicator Manual t It is normal to see the progress indicator stays at 010% and 100% for approximately 30 seconds for CD duplication and up to 1 minute for DVD duplication. That is caused by the initializing and finalizing stages. Once the duplication run is completed, the good copies will be ejected and you shall see the following screen: Once the number of blank discs you inserted matches the number of discs detected on the screen.
t Reflex Duplicator Manual t Reflex Duplicator Manual Tutorial Guide: If you happen to have any failed discs (bad copy), the failed disc(s) will not be ejected automatically. You need to manually eject them and throw them away if they are write once recordable disc(s). III. Select the Duplication Speed This process will allow you to adjust the duplication speed subject to your various needs. NOTES By default, the duplication speed will be set to the optimal speed.
t Reflex Duplicator Manual Disc Makers 5. Setup t DVD to greater than 6x duplication speed. To achieve maximum duplication speed, you need to perform duplication tasks from the Hard Drive. For detailed instructions, please refer to “Tutorial Section II ñ Make Hard Drive-to-Disc Copies.“ .99 Press “ENT“ and the first option will be: Setup 5.1 Select Burn Speed Reflex Duplicator Manual 4. Select Desired Duplication Speed.
t Reflex Duplicator Manual t Tutorial Guide: IV. Reflex Duplicator Manual Disc Makers 1. COPY .99 Select the Master Reading Source When you try to make a copy, you need to specify where the master disc is. Is it in the Reader tray? Or is it an Image inside the Hard Drive? This tutorial will show you how to change the Master Reading Source to satisfy your needs. 1. Press UP or DOWN arrow button or “Source“ hot key to navigate to the following screen.
t Reflex Duplicator Manual t Reflex Duplicator Manual Tutorial Guide: Then you will be directed back to the menu: SetUp 5.2 Select Source V. Load Master Disc onto the Hard Drive In order to copy from the Hard Drive, you are required to load your master disc onto a hard drive partition. After loading your master disc to the Hard Drive, please make sure to remove your master disc from the Master Reading Tray. Failure to do so might cause improper duplication.
t Reflex Duplicator Manual t *The “1” indicates the number of partitions you’ve already loaded into the Hard Drive . (Includes the Reserved Partition) *The “8” indicates the total number of partitions you can load to the Hard Drive. Hard Drive Port 0 WDC WD400EB-75CPF0 Make sure it is located at “Hard Drive“. If not, then you need to press UP or DOWN navigation button to search for it. c. Press “ENT“ to submit your selection. After your selection has been submitted, you will see the following: Setup 5.
t x. xi. xii. xiii. Reflex Duplicator Manual Press “ENT“ button once to move the cursor to the next position. Load Partition OK! Press OK to Continue Press “ENT“ button once to move the cursor to the next position. Press “DOWN“ button consecutively until “N“ is displayed. xiv. Press “ENT“ button once to move the cursor to the next position. xv. Now, we have the name “FUN“ displayed and then, press “ENT“ consecutively until the cursor is moved to “OK“. xvi.
t Reflex Duplicator Manual Choose Partition 1->[FUN ] DVD 4. Use UP or DOWN arrow button to find the desired partition and then press “ENT“ to submit your selection and you shall see the following confirmation screen: Rename Partition [FUN ] DVD, OK? 5. Press “ENT“ once again to confirm it and you shall see the following: Rename Partition [FUN ] OK 6. Now, you can rename the partition youíve just selected. t Reflex Duplicator Manual ii. Now, we have renamed the image name “FUN“ to “FUN2“.
t Reflex Duplicator Manual Tutorial Guide: VII. Delete Existing Hard Drive Partition Permanently If for some reason you would like to delete your existing hard drive partition permanently, you can do the following: 1. Use UP or DOWN arrow button to navigate to the following screen. Disc Makers 3. Image 2. .99 Press “ENT“ and use UP or DOWN arrow buttons to navigate to the following screen: Image 4. Delete Partition t Reflex Duplicator Manual 4.
t Reflex Duplicator Manual Tutorial Guide: VIII. Changing the Hard Drive Partition Size If you have a 16x speed or higher duplicator with double layer/dual layer DVD9 capability, the hard drive partitions are set at the default size of 9GB each to accommodate for the expanded size of the DVD9 format. If you require more partitions and do not plan on utilizing double layer/dual layer DVD9 media, you will need to change the Hard Drive partition size to 5GB.
t Reflex Duplicator Manual t Reflex Duplicator Manual Tutorial Guide IX. Change the SETUP settings Most of the internal settings and information is stored inside the SETUP menu. To explore and modify them is simple. Below is an example to modify the “Auto Start“ setting. Please note that the default setup is set for optimal performance of the duplicator, it is unnecessary to change if you are satisfied with the outcome. 1. Use UP or DOWN arrow button to navigate to the following screen. Disc Makers 5.
t Reflex Duplicator Manual Tutorial Guide: X. t 1. Audio CD Editing Reflex Duplicator Manual Going to the “Edit Audio Track“ menu Use the UP or DOWN arrow button to navigate to the following screen and press “ENT“. This process will guide you to perform the Audio Track Selection feature. This process will help you combine audio tracks from various CDs into a single customized audio CD.
t 3. Reflex Duplicator Manual Once you made your selection, you shall see the following: Preparing... Waiting for Master OR Preparing... Waiting for a Blank When you see above, please insert an audio CD that contains your favorite track(s) in the Master Reading Tray and a blank CD-R media into one of Writer Trays. If either one of the ABOVE 2 screens is shown for more than 2 minutes, please check your Master Disc or Blank Discs for quality.
t Reflex Duplicator Manual If you choose to insert another audio CD for more songs, you need to press DOWN arrow button until you see the following screen: Total 6 Trk 26m:17s Insert Next Master?> Then, press “ENT“ button to continue. After that, your old master disc will be ejected and you can insert another audio CD into the Reading Tray. Please go back and follow the instruction on Step 3.
t Reflex Duplicator Manual Example of Editing Audio Tracks to Hard Drive (For Duplicators with Hard Drive Installed): t Reflex Duplicator Manual will appear on the left of “Track 4“ like following: Total: 2 Trk 9m:47s *Track 4: 4m:58s We need to create a new Audio CD from 2 different Discs. CD1: song 2, and song 4 CD2: song 3, song 4 and song 5 1. Go to function 11. Edit Audio Track DUPLICATOR 5.00 11.Edit Audio Tracks 8.
t Reflex Duplicator Manual 13. Use the UP or DOWN arrow button until you see “Track 3“ on the 2nd line, and then press “ENT“ to confirm. A “*“ symbol will appear on the left of “Track 3“ like following: Total: 3 Trk 14m:35s *Track 3: 4m:47s 14. Use the UP or DOWN arrow button until you see “Track 4“ on the 2nd line, and then press “ENT“ to confirm. A “*“ symbol will appear on the left of “Track 4“ like following: Total: 4 Trk 20m:01s *Track 4: 5m:26s 15.
t Reflex Duplicator Manual Tutorial Guide XI. Introduction to Account Management Feature This feature allows you, the administrator, to have the power to: 1. Create user accounts and passwords to prevent unauthorized use of this duplicator. 2. Edit existing user account information, including name and password. 3. Delete existing user account(s). 4. Enable/Disable this feature. This feature is disabled by default.
t Reflex Duplicator Manual t digit of your password and press “ENT“ button to submit the current digit and you will be guided to select the next digit. Repeat above steps until youíve selected all digits of your password. After you have entered the password, you need to press “ENT“ button on “OK“ to submit your password. Each user has their own settings and hard drive partitions. During this process, you will be prompted to enter a new user name and user password for a new account.
t Reflex Duplicator Manual t Reflex Duplicator Manual Tutorial Guide Manage Accounts 4. Delete User XII. This menu allows you to delete the existing user account. During this process, you will be asked to select the existing account to be removed. - User “Admin“ is the administrative account; you can NOT delete this account. Press “ENT“ button to enter into this menu and press “ESC“ button to go back to the main menu or cancel the current selection. 5. Password on Bootup Manage Accounts 5.
t Reflex Duplicator Manual To simplify this process for anyone, we introduced a new feature called “Load and Copy“ under the new category “Duplication Mode“. This feature reduces the “Duplication from Hard Drive“ process to a single step! There are two features under “Duplication modes“: t Reflex Duplicator Manual duplications from the reserve partition will be with the new image. Advantage: Faster duplication in a long run.
t Reflex Duplicator Manual t Reflex Duplicator Manual Tutorial Guide Press UP or DOWN Button Consecutively until you see following: Disc Makers Setup .99 Press “ENT“ and use the UP or DOWN arrows to navigate to the following: Setup 10. Duplication Mode Press “ENT“ button once. You shall see following: Duplication Mode: Auto Press UP or DOWN Button Consecutively to select your desired mode. Duplication Mode: Load and Copy Press “ENT“ button once to submit your selection.
t Reflex Duplicator Manual 3. Press “ENT“ to enter the AUTOCOPY Setting Menu and you shall see the following: AUTOCOPY: Off 4. Use the UP or DOWN arrow button to modify the setting to “On“ and then press “ENT“ to submit your selection and you shall see the following: t 8. Please allow 5-10 seconds for the duplicator to detect your Master Disc and Blank Discs. After your Master Disc and Blank Discs have been recognized, you will see the following screen: Processing... Please Wait 9.
t Reflex Duplicator Manual 10. Once the duplication run is completed, the successful copies will be ejected and you shall see the following screen: PASS 7 FAIL 0( 7)O Waiting for Blanks - “PASS 7” indicates that you’ve just made 7 successful copies. - “FAIL 0” indicates that you have no failure in this run. - “7” indicates that you’ve successfully copied 7 copies so far. Next, refill your Blank Discs to continue making more copies.
t Reflex Duplicator Manual t Menu Overview: 1. 2. 3. COPY This menu will guide you to make CD/DVD copies. Before you enter this menu to copy, please make sure you have selected the correct Master Reading Source. For more information, please refer to “Tutorial Guide I ñ Make Disc-toDisc Copies“ or “Tutorial Guide II ñ Make Hard Drive(HDD)to-Disc Copies“ ADVANCED COPY OPTIONS 2.
t Reflex Duplicator Manual t Reflex Duplicator Manual 5.9 two different modes, “Disc at Once“ and “Track at Once“. Unless you understand completely what they mean, we strongly suggest you to set it as “Disc at Once“. 5.5 Max Audio VCD and CDG Speed - Audio CDís and Video CDís do not have internal error checking capability, so duplicating at too high a speed may cause frequent errors. This setting will allow you to adjust the maximum duplication speed for Audio and Video CD 5.
t Reflex Duplicator Manual occurs, it tends to waste all of your blank recordable media. 5.3 System Info - By entering this menu, you will be able to see the many specification of your duplicator such as the firmware version, CPU type, RAM capacity. You can check the specifications by pressing UP or DOWN button 5.4 Device Info - By entering this menu, you will be able to see the information for devices built inside your duplicator 5.
t Reflex Duplicator Manual Trouble Shooting 1. No display on LCD or the unit does not operate when the power is on. Check the connection of power cable and the environment of power outlet is normal. Make sure the power voltage matches the voltage of your power outlet. If the duplicator was stored in a location where the temperature dropped below 32ðF (0ðC) within the past 24 hours, leave the duplicator in a warm room with temperatures at least 65ðF (19ðC) for 4 hours prior to powering it on. 2.
t Reflex Duplicator Manual 11. How do I reset my duplicator back to default? I) Use UP or DOWN arrow button to navigate to the following screen. Disc Makers 5. Setup .99 II) Press “ENT“ to enter Setup Menu and you shall see the following: Setup 1. Select Burn Speed III) Use UP or DOWN arrow button to navigate to the following screen. Setup 12.
