Perfect Control Solution System Controller SCC-3100A User’s Manual SALES NETWORK • SAMSUNG TECHWIN CO.,LTD. 145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, 462-120, Korea TEL : +82-31-740-8151~8 FAX : +82-31-740-8145 • SAMSUNG TECHWIN AMERICA,LTD. 1480 Charles Willard St. Carson, CA 90746, UNITED STATES TEL : +1-310-632-1234 FAX : +1-310-632-2195 • SAMSUNG OPTO-ELECTRONICS UK,LTD.
Contents 6 6 7 7 8 8 8 8 9 9 9 10 10 11 12 13 13 14 16 16 17 17 17 18 19 19 19 20 21 21 21 22 22 21 23 23 22 24 24 24 6. MODEL 7. TRACE 7-1. TRACE Memory 7-2. TRACE Operation 8. AF 9. OSD DVR Mode CONTROLLER Mode 1. Setup Mode 2. ID Setup 3. SERIAL Setup 4. DATA COPY 5. RESPONSE 5-1. SPD-3300/3000/2300 DIP Setup 5-2. SPD-2500 DIP Setup 5-3. SPD-2200 DIP Setup 5-4. SPD-1600 DIP Setup 6. PASSWORD 6-1. PASSWORD Setup 6-2. Applying Password-Setup Mode 6-3. Applying Password-Power 6-4. Entering Password 7.
Safety caution Safety caution SYSTEM CONTROLLER 4 User’s Manual Caution • Use the appliance indoors only. - Do not place the appliance outdoors or expose it to rain or moisture. - If dropped in water, the appliance may be corroded and damaged. • Do not use the appliance where there is excessive dust, smoke, or moisture. - Using the appliance under such conditions may result in fire, electric shock or serious damage. • Do not operate the appliance in temperatures beyond those specified.
Major Functions and Features ENGLISH 3. Controller Button Layout Major Functions and Features 1. Overview This product is designed for use only with the Speed Dome camera, CCTV receiver, and Samsung Digital Video Recorder.
System Overview System Overview 1-1 Connecting Controller and Junction Box 1-2 Connecting Junction Box and External Devices 3.RS-232C Pin Layout (D_SUB_MALE) [SVR-1630 connection] [SVR-1650/1640/950/1630/430/440 connection] * RX+ and TX+ / RX- and TX- must be shortcircuited. [PTZ connection] (SPD-3300/3000/2300, SPD-2500/2200/1600) * RX+=DATA+ RX- =DATA • All supported SPEED DOME functions can be controlled when the PTZ camera is connected through the SVR-1650/1640/950.
System Overview Names and Functions of Each Part 1.Camera Setup Section ENGLISH 5. General Connection RESET PRESET SWING : Resets camera power. : Moves camera to the preset location (see p.21). : Continuously travels between two assigned locations horizontally (pan) or vertically (tilt) (see p.22). AUX 1 : Toggles the camera's external device AUX1 on and off. GROUP : Repeats sequential surveillance of assigned preset locations with preset movement rates and intervals (see p.23).
Names and Functions of Each Part Names and Functions of Each Part 0~9 : Used for entering camera ID, channel number, monitor number, DVR ID, etc. (see p.26). MONITOR : Select a monitor for matrix output CAMERA : Enter camera number and press the CAMERA button to set the camera ID (PTZ mode) or set the channel (DVR mode).
Names and Functions of Each Part STATUS SEARCH REC MENU MULTI AUTO ALRAM RESET PIP DVR FUNCTION DIGITAL ZOOM COPY RELAY LIVE / PLAY BACK + : The Quick Setup menu is displayed in the DVR monitor. : The current DVR status is displayed in the DVR monitor. : Used for searching the DVR recording list. : Used to start recording the surveillance screen. : The DVR menu is displayed in the DVR monitor. : Used for switching the DVR monitor from single screen playback mode to multiple screen playback mode.
Names and Functions of Each Part 1. Power-On Joystick : Used for moving the camera up, down, left, and right, and for zoom control (see p.18). 1) Tilt up (Up button) : Moves the camera up. 2) Tilt down (Down button) : Moves the camera down. 3) Tilt left (Left button) : Moves the camera left. 4) Tilt right (Right button) : Moves the camera right. 5) Turn stick clockwise : Performs telephoto-zoom. 6) Turn stick counter-clockwise : Performs wide zoom. ESC(PTZ) : Same as ESC in SPEED DOM OSD MENU.
PTZ CONTROL PTZ CONTROL 5. SPEED DOME OSD Menu Control The joystick can be used to control the camera s left and right (pan) and up and down (tilt) movements. ENGLISH 4. Joystick/Camera Control Button This is the ENTER/ESC button for SPEED DOME OSD MENU ESC : ESC button for PTZ CAMERA OSD menu. ENTER : ENTER button for PTZ CAMERA OSD menu. Remarks • Press the Esc (PTZ)/Enter (PTZ) button for 2 sec. or longer, then let go to adjust the movement speed of the camera manually.
PTZ Mode PTZ Mode Press the SETUP button on the initial screen to display the [SETUP SYSTEM] menu. button to activate the [ This menu is for setting the camera to move to preset locations. 2-1. PRESET Setup ] At the [PTZ SETUP 1 ] menu, press the 1 button (see p.21). Use the joystick or camera control button (SCC-3100 model) to move the camera to the desired location (move up, down, left, and right, and control zoom). PTZ SETUP Enter a preset number.
PTZ Mode PTZ Mode 4. GROUP This menu is for setting the camera to alternate between two assigned locations horizontally (pan) or vertically (tilt). Setting the SWING SETUP menu by controllers is only possible in the SPD series. In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more information. This menu is for setting repeated sequential surveillance of assigned locations with assigned speed and intervals.
PTZ Mode PTZ Mode ENGLISH 5. TOUR This menu is for setting one or more Groups for Tour so that continuous Group operations can be carried out. The TOUR SETUP menu is only available for an SPD series. 5-1. TOUR Setup At the [PTZ SETUP 1 (see p.21). ] menu, press the 4 button Press a Group number to add to the Tour. • Up to 6 Groups can be added. Press the ENTER button to finish the setup. 5-2. TOUR Operation At the initial screen, press the Tour button. The Tour function is performed.
PTZ Mode PTZ Mode 7. TRACE This menu is for setting the PTZ camera ID and camera type. At the [PTZ SETUP 1 (see p.21). ] menu, press the button Press the 1 button to move to the Model Setup screen. This menu is for inputting camera movements, through joystick or camera control buttons, into the memory for a certain period of time, to allow repeating of stored movements when performing the Trace (PATTERN) function. Setting the TRACE SETUP menu by controller is only available for an SPD series.
PTZ Mode PTZ Mode 9. OSD This menu is for adjusting camera focus manually or automatically after camera operation. If AF is set to OFF in the camera setup menu, set the AF of the controller to ON and then automatic adjustment is performed after camera operation. At the [PTZ SETUP 1 (see p.21). ] menu, press the button This is used for displaying the camera menu on the monitor. Press the OSD button from the PTZ or DVR mode. (Warning: Execute only from the Master controller).
DVR Mode Contents Model SVR-5416/5116 This menu is for setting the DVR ID and model for operation by a controller. Sub-controllers cannot be used if the master controller is in Setup mode. • To connect to the SVR-5416/5116: System Remote Controller setup Serial (RS232/RS485) check on Serial setup Communication Port 1/Equipment Number setup (Port setting must be identical to controller’s communication settings.
Controller Mode 4. DATA COPY This menu is for setting controller ID. At the [Controller SETUP 1 ] menu, press the 1 button (see p.31). Press a number on the number pad to enter a controller ID. Press the ENTER button to set the controller ID. • Assign number 1 for setting the controller ID for the master controller. • The lower the ID number, the higher the controller priority. • Sub-controllers can be operated only when connected to a master controller; Sub-controllers cannot be operated independently.
Controller Mode Controller Mode This menu is for setting RESPONSE function of the camera which is connected Controller. At the [CONTROLLER SETUP 1 ] menu, press the button (see p.31). Press the 1 button to open the Response Setup screen. Press the 1 button to set the controller RESPONSE setting to ON. The controller automatically restarts to apply the change.Press the 2 button to set the controller RESPONSE setting to OFF.
Controller Mode Controller Mode This menu is for setting the password to enter when changing controller setup values upon power-on. At the Password Setup screen, press the 2 button. 6-1. PASSWORD Setup At the [CONTROLLER SETUP 1 ] menu, press the button (see p.31). Press the 2 button to activate the Password Setup screen. Press the 1 button to ask for a password every time the setup mode is selected. Press the 2 button to skip asking for a password. 6-3.
Controller Mode Controller Mode 8. DEFAULT This menu is for setting the connected sub-controller to use a PTZ camera or DVR within the specified restrictions. This menu is available for master controller (ID: 1) only. At the [CONTROLLER SETUP 1 ] menu, press the button twice. (see p.31). Press the 1 button to activate the Priority Setup screen. Press the 1 button to change the controller setup values to the default values and restart the controller. Press the 2 button to cancel the process.
MATRIX Mode MATRIX Mode 1. Selection of Camera and Monitor Select a number between 1 and 255, and then press the CAMERA button to select the corresponding camera. This is a manual function to display the cameras connected to the MATRIX SYSTEM on the monitor. Select Monitor : Select a monitor number between 1 and 32. Press MONITOR. Select Camera : Select a camera number between 1 and 255. Press CAMERA. • Monitor must be selected before the camera.
MATRIX Mode MATRIX Mode This is a function to enter text on the corresponding camera. [MATRIX screen] 4-1 Select ID SET From the initial screen, press the MATRIX button, and then press the MENU button to display the [MATRIX CONTROL] menu. Press button 3 to display the [CAMERA ID SET] menu. (In MATRIX, wait for data loading completion.) Move the joystick to select the ID CHANGE SET from the MATRIX screen, and then press the “FOCUS +“ button.
MATRIX Mode What to do when the product malfunctions From the initial screen, press the MATRIX button, and then press the MENU button to display the [MATRIX CONTROL] menu. Press the 4 button to display the [TIME SET] menu. (In MATRIX, wait for data loading completion.) Move the joystick to select the TIME/DATE ON/OFF from the MATRIX screen, and then press the “FOCUS [MATRIX screen] +“ button. Move the joystick up/down to select a monitor, move it left/right to select ON/OFF.
Controller Specifications SCC-3100A ENGLISH MODEL Connector LCD Display PTZ Operation Sub Keyboard 3 Port 20 x 4 Character LCD Joystick (3 axis Twist Zoom) Max. 16 things connection Speed Dome Samsung Techwin(SPD), PELCO-D, PELCO-P, PANASONIC (PANA), SAMSUNG ELECTRONICS (SEC), ELMO, BOSCH Control Control Quantity Auto Surveillance Remote Control RS-485/422 Spec.
