WOOD PELLET GRILL ZPG - 550B OWNER’S MANUAL 1-833-947-4557 EMAIL:support@zgrills.com WEBSITE:www.zgrills.
CONTENTS WARNINGS 3 COMPOENT LIST 4 ASSEMBLY INSTRUCTIONS 5 INITIAL FIRING INSTRUCTIONS 11 SUBSEQUENT START-UP 12 OPERATING TIPS 14 MAINTENANCE & CLEANING 15 TROUBLESHOOTING 17 DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM 19 Z GRILLS SUPPORT 20 3-Y LIMITED WARRANTY 21 1
WARNINGS! This grill is for outdoor use only. Do not use it in any enclosed area. Do not store or use combustible materials or liquids near this appliance. Keep young children away while it is in use. Maintain a long safe distance between your grill and any combustible. Do not move your grill while operating or while it is hot until the grill is completely cold. If a grease fire occurs, turn “off” and leave lid closed until the fire extinguished. Do not unplug the power cord. Do not throw water on it.
ASSEMBLY INSTRUCTIONS COMPONENT LIST ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 4 Qty 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 2 2 1 1 4 1 1 Description Grill Chamber Assembly Hopper Assembly Warming Rack Porcelain Grills Grease Drain Pan Heat Baffle RTD RTD Guard Lid Handle Handle Guide Lid Hinge Assy Chimney Cap Smoke Stack Assembly Smoke Stack Gasket Grease Basket Right Leg Wheels Axle Bottom Plate Left Leg Pipe Plug Hopper Lid Hopper Shell ITEM 25 26 27 28 29 30 31 32 33 34 35 36
3.) Take the Axle(19), the Flat Gasket (E), the Spring Washer (F), the Cap Nut (G). From inside to outside,according to the picture, after the orderly assembly, tighten it. The two sides are assembled in the same way.Then put the whole machine in the right place and tighten all the Bolts with the Screwdriver (A). Finally,press the Wheel Cap(38) firmly into the groove in the middle of the wheel. 1. MOUNTING THE BODY FRAME TO THE CHAMBER 1.
2.INSTALLING THE CHAMBER HANDLE TO THE LID: 4.1.INSTALLING THE HEAT BAFFLE: 1.) Take out the Lid Handle(9) and remove the Bolts (H) and Flat Gasket (D) from the Lid Handle(9). 2.) Attach the Bolts(H) through Flat Gasket (D) and the Lid(11) orderly, install the Handle to the Lid. Use Wench(B) to tighten them. 1.) Place the lower bracket of the Heat Baffle(6) into the groove of the feeder. As shown. 3.INSTALLING THE SMOKESTACK AND CHIMNEY CAP: 5.INSTALLING THE GREASE DRAIN PAN: 1).
6.INSTALLING THE COOKING GRATE AND WARMING RACK: INITIAL FIRING INSTRUCTIONS 1.) Install the Porcelain Cooking Grate(4) and Warming Rack(3) into the Chamber. As shown. Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 7.HANG ON THE GREASE BUCKET: 1.) Located the Grease Drain Tube which is on the right side of the Chamber, then hang the Grease Bucket(16) on the hook. As shown. 1.
SUBSEQUENT START-UP Please take attention: If the grill fails to light or the fire in the Firepot goes out while cooking, it is vital to follow these steps when sufficient pellets are still in the Pellet Hopper. Failure to follow the steps may cause a hazardous “over-firing” of your grill due to an excess of unburned pellets in the Firepot. 1.Turn OFF the appliance and unplug the Power Cord. After the grill cool down, remove all food, the Porcelain Grills, Grease Drain Pan and the Heat Baffle. 2.
OPERATING TIPS 1.Just like other barbecues, the actual temperature of this grill or the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets and so on. 2.It is better to shelter your grill from the wind, this will aid in temperature output, heat retention and heat recovery time when opening the lid. MAINTENANCE & CLEANING Your Z Grills also needs your maintenance. Make sure your grill is OFF and cold completely before performing any maintenance and cleaning.
TROUBLESHOOTING cleaning brush to give the Porcelain-coated Grill Grates a quick brushing when you finish the barbecue. It takes only a minute and it will be ready the next time you want to use the grill. Clean the inner temperature probe after each time use. Ash Clean the ash from the interior of the grill periodically, otherwise excess ash in the firepot may cause your fire to go out, especially in the SMOKE setting. A shop vac is an excellent tool to handle the ash.
DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM Unexpected grill temperature is displayed External Factor Grill temperature is influenced by environmental factors such as high temperature, wind and direct sun. Place unit in shaded area. Open the lid to reduce inside temperature. Excess or discolored smoke Pellets Replace moist pellets with fresh dry pellets.
Z GRILLS SUPPORT Thank you for shopping with us! If you have any question, feel free to contact us or your dealer. Z GRILLS INC. will offer the best technical and sales support in the industry. Please be prepared to provide the following information: Dealer's name, date of purchase Purchaser's name, phone number, address, Z Grills model number, serial number and part identification number from the COMPONENT LIST Please describe your problem accurately so that we can help you figure out.
[ Page intentionally left blank ] 22
