L il PART DESCRIPTION Control Panel 1 < Marble Stone Top 1 B Ce==F Burner Tray Support Brackets 2 E —— L.P. Tank Drawer Side Support 1 F Front Panel 1 & Right Side Panel 1 " Left Side Panel/ 4 LP.
NO, i s any 3 @ Gas Tank Bracket 1 K = Screws (4°40) 10 L = Screws (4*16) 16 M S Bolts 1 N Flat Washer (M8) 4 o @ Spring Washer (M8) 4 P among” Bolt (MB*18) 4 { a (me: S) 10 kgs fire glass 1 \ L e R Cover 1
FRAME ASSEMBLY PART ONE Attach the front panel (F} to the left side panel (H), using the strews () on the top and bottom.
the craws {K). FRAME ASSEMBLY PART TWO Repeat the same on the opposite side by sign 2' attaching the back pane! to the left side panel/LP.
FRAME ASSEMBLY PART THREE Attach the right side pane! (G} to the front and back pane! (HF} using four of the strews (K. Step. NUNS AT Tilting the fire table, place the 2 side panel {H}. Use the L) screws to attach the front and back near the center of the talkie, and the ] screws to attach the bracket near the left side pant, gas tank bracket (i} underneath the frame near the LP tank access door/left Use the screw (M} for LP. tank support. LB.
L.P. KART BRACKET ASSEMBLY PART TWO . Using the (L) screws, insert the LP. tank drawer support in the censer of the frame. %oWD\ Haidas PSS a&&v h% F%.. I WSy IRl A.. S s fiflfififl& BURNER TRAY SUPPORT ASSEMBLY .
“ 1 TABLE TOF FRAME ASSEMBLY Place the marble top (0 on top of the efl 5 || panels, using the washers (N+0) and the bolt {P) to secure. BURNER TRAY AND CONTROL PANEL ASSEMBLY Set the su a Burner Tray (A} in the middies of the stone top (C ), and secure using the screws. Using the {L) screws, secure the Control Panel (8) in the opening in the front pane! {i).
ADD GLAZE MEDIA Pour grass media {Q) into the burner tray. Take care not to add more than 172 inch of media over the flame element. the LP Tank {not included).
Place a AA battery in the LP Valve/Starter Pane! before trying to ignite. (Note: Battery not included,) CAUTION: Before Igniting, turn the valve on the LP tank. Apply soap water anti all of the leaking components. If bubbles appear, tighten it and apply soup water again. [Fno bubbles appear, turn off the valve and proceed to ignite.
LIGHTING INSTRUCTIONS Make sure propane tank valve Is open, 1.7 ignite, push the regulator knob forward and tum one quarter turn counter clockwise to the ignite” passion, 2,With the naive depressed, push the ignite button 1o make the plait burner gite.
SHUTTING OFF FIRE TABLE To shut off, close the valve at the propane tank taking care to ensure the flame Is completely extinguished, Push the scalp regulator valve in and turn to the off position. Allow 5-minutes of complete shut off before the appliance Is reignited.
METAL FRAME MAINTENANCE RST Brands furniture incorporates metal frames, which are designed to require minimum maintenance. » Metal frames should be kept clean. Do not let dirt build up on the metal surfaces. Cleaning with mild soap and water is all that is required. Never leave furniture standing in water. To keep your furniture looking its best, you may wish to store or cover your furniture when not in use for an extended period of time.
LG e P important: Read these instructions carefully before starting Installation «f the outdoor fire table, Operation Checklist Fora safe and pleasurable heating experience, perform this check before each use. Ba fore operating, confirm: 1.1 am familiar with the entire owner’s manual and understand 2. All components are properly assemble, Intact, and operable. 3. Mo attestations have hen made. 4, All gas connections are secure and do not elks. 5. Wind velocity is below 16 mph.
Estimated assembly time: 15 minutes, Tools squired (not included) Phillips screwdriver with medium bias, and leak detection solution. Code and supply requirements: The Installation of this product mist conform with local codes ar, In the absence of acacia codes, with the latest National Fuse Ges Code, ANS| Z223.1. £ pacer & warning Bo not store or use gasoline, of other you small gas: line, o . flammable vapors and liquids, in the 1. Shut off gas to the appliance. 2. Extinguish any open Rae.
PER-INSTALLATION AND PREPARATION SAFETY GUIDELINES 1. Before Installing this unit, check the minimum clearance to combustibles section ta ‘ensure that the surrounding ares ik properly steed for the installation, 2.
INSTALLATION SAFETY GUIDELINES 1. Installation and repeal wouldst be done by = qualified service person, The appliance should be inspected before use and at east annually by a qualified service person, More frequent
IMPORTANT SAFETY INFORMATION BE CAREFUL if ot Installed and used correctly par theses Instructions, this sect cam cause seniors Injure CAUTION: Installation and maintenance must be done by an NFi Certified o other qualified professional installer. Read these Instructions before Inst ailing this outdoor firs table. Be sure you understand ai safety precautions and wakings contained n this manual. A FOR OUTDOOR USE ONLY. THIS UNIT MUST BE INSTALLED AT LEAST 36* FROM ANY COMBS. WHITEWALLS OR MATERIAL.
L LU R Ir stall the regulator hose assembly {not supplied) to the ult using 2 gas pile sealing compendium or Propane Fig. 101 Teflon Ope. Then attach the guarantor end to the cylinder propane cylinder and tighten {see Fig. 10-1). Folio sl Instructions and safety warnings supplied with the propane cylinder, Pace the cylinder In the tank sat, and rate the screw clockwise to a fully stop. (see Fig. 10-2) CONNECT TO A NATURAL OR HOUSEHOLD Regulator hose PROFANE GAS SUPPLY from unity 1.
LAVA GRANULE & GLASS CRYSTAL INSTALLATION GUIDELINES A, Carefully inspect the carton for shipping damage. If any parts are missing or darn aged, call your dealer. Do not pattern to install the appliance unless all parts are in good condition. B, Correct installation is crucial to safe performance of your Outdoor Lira Pit. £. Due to high temperatures, the Fire Pit must be located out of traffic areas and away from combustibles.
OPERATING THE UNIT LIGHTING AND EXTINGUISHING FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE. A, BEFORE LIGHTING, smell all abound the unit area for gas. Be sure to smell next to the floor, because some gas is heavier than air and will sentient on the floor 8. WHAT TO DO IF YOU SMELL GAS a. Shut off the gas to the appliance, b.
iy Each installation site for any purity presents its own unique combustion environment. Specific factors sis ch ‘s weather, wind currents, yard debris, altitude, drafts, the size of the surrounding ars, all have an influence of the proper operation of the unit. & normally operating unit wil demonstrate the following characteristics: 2. Lively, realistic yellow flame, . Odor-free.
Plateau du brideur Panneau de commande 3 T Dessus en pierre marbrière 1 o Supports du plateau du briseur ASSEMBLAGE latéral du tiroir 1 de Iz bouteille Panneau avant 1 G #anneau [latéral droit 1 H Panneau latéral gauche/ porte d’accus & la bouteille de PL 1 Panneau arrière 1
£ ASSEMBLAGE DU CADRE PARTIE 1 Attacher le panneau avant (Fla LaSalle I. panneau latéral gauche (H) au moyen des vis (K) au sommet et 3 a base.
i ASSEMBLAGE DU CADRE PARTIE 2 Attacher le panneau arrière ( au Etm panneau latéral gauche/porte d’accus moyen des vis
3 ASSEMBLAGE DU repartie 3 Attacher le panneau latéral droit (G) aUX pruneau avant ot arriéré (+F) au moyen des quatre vis {9, Tape 3. ser les vis (L) pour attacher avant et Parricide 3 proximités du &, et les vis (K] pour attacher le support prés du pannes inclinant |a table foyer, placer e support de la bouteille de gaz (f} sous le cadre & proximité de la porte d’accus de Ia boute-selle de PL/du panneau latéral ASSEMBLAGE DU SUPPORT DE LA BOUTEILLE DE PALMIPARTIE -En latéral gauche.
N ASSEMBLAGE DU SUPPORT DE LA BOUTEILLE DE partiez Au moyen des vis (L, Insérer e support du tirailler de 1a bouteille centre du cadre. SIS, qw..mww ASSEMBLAGE DU SUPPORT DA PLATEAU DU BRODEUR Au moyen des vis p o (L), Insérer les supports du plates du brûleur (D) au sommet du cadre, B s FERRARAISE.
ASSEMBLAGE DU CADRE DV DESSUS DE TABLE Placer le dessus en marbre {C) sur les panneaux au moyen des rondelles et du boulon {P} pour e maintenir en place, ®\-L ASSEMBLAGE DU PANNEAU DE COMMANDE ET DU PLATEAU DU Eh s BRODEUR .
AJOUT DU MEDIA EN Ver reverser le média en verre (Q) dans le plateau Lourdeur, Faire attention de ne pas verser plus de 1,25 cm de médium sur ies flammes INFLATION DE LA BOUTER LE DE PROPANEFixer I tuyau de 1a bouteille plateau du relieur & la bouteille de PL (non incluse).
Placer la pile AA dans le panneau de démarrage/de ls valve PL avant o allumer, REMARQUE: pile non incluse. z AVERTISSEMENT: Avant & allumer, surir [3 valve de la bouteille Appliquer de eau savonneuse sur tous les composants présentant des cultes. St aucune bulle #’ apparat, fermer {3 valve ot procéder 3 ' allumage.
EXTINCTION DE LA TABLE BRASER Pour " étendre, fermer i3 valve de ia bouteille de propane en vérifiant que a larme est complètement Teinte. fh'. Is Appuyer sur i bouton de réglage et le tourner en position ÉTEINTE, Laisser " appareil entièrement éteint pendant 5 minutes avant de le rallumer.
MAINTENANCE BU GARE EN MÉTAL Les meubles RST Brand équipés de cadres en métal sont fongus pour requérir une maintenance minime. = Les cadres en métal doivent rester propres. » Ne pas laisser |a poussière s’accumuler sur les surfaces en métal. « 1l suffit de nettoyer avec du savon doux et de 'sau. + Ne jamais laisser de meubles dans l’eau. = Pour maintenir vos meubles en bon état, il est conseillé de les ranger ou de les couvrir lorsqu’ils ne sont pas en cours d‘utilisation pour une longue période.
inspecter soigneusement ie carton pour rouvre des dommages d’expédition, Sill s iés pinces manquantes ou endommagées, contactez votre revendeur, N'essayez pas déstaliniser "appareil 3 moins gue toutes les composantes dolent en bon &at. B. Une installation correcte est essentielle pour un fonctionnement sr de votre foyer d’extérieur Foyer, €. En raison de températures élevées, le foyer doit dire situé hors de zones de passages et loin de combustibles.
