User guide

ManualsBrandsDiodes ManualsHardwarePDR3G

DS30547 Rev. 7 - 2 1 of 3 PDR3G

PowerDI is a trademark of Diodes Incorporated. www.diodes.com ã Diodes Incorporated

PDR3G

3A GLASS PASSIVATED RECTIFIER

PowerDI

Features

Single phase, half wave, 60Hz, resistive or inductive load.

For capacitive load, derate current by 20%.

Mechanical Data

Characteristic Symbol

Value

Unit

Peak Repetitive Reverse Voltage

Working Peak Reverse Voltage

DC Blocking Voltage

RRM

RWM

400 V

RMS Reverse Voltage

R(RMS)

283 V

Average Rectified Output Current (See also figure 4)

3 A

Non-Repetitive Peak Forward Surge Current

8.3ms Single half sine-wave Superimposed on Rated Load

FSM

100 A

Maximum Ratings

@ T

= 25°C unless otherwise specified

LEFT PIN

RIGHT PIN

Note: Pins Left & Right must

be electrically connected

at the printed circuit board.

BOTTOMSIDE

HEAT SINK

PowerDI

Dim

Min Max

1.05 1.15

0.33 0.43

0.80 0.99

1.70 1.88

3.90 4.05

3.05 NOM

6.40 6.60

1.84 NOM

5.30 5.45

3.55 NOM

0.75 0.95

0.50 0.65

1.20 1.50

All Dimensions in mm

Characteristic Symbol Typ Max Unit

Thermal Resistance Junction to Soldering Point

qJS

¾ 2.0 °C/W

Thermal Resistance Junction to Ambient Air (Note 2)

qJA

75 ¾ °C/W

Thermal Resistance Junction to Ambient Air (Note 3)

qJA

65 ¾ °C/W

Thermal Resistance Junction to Ambient Air (Note 4)

qJA

45 ¾ °C/W

Operating Temperature Range

-65 to +150 °C

Storage Temperature Range

STG

-65 to +150 °C

Notes: 1. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7.

2. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. T

= 25°C

3. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. T

= 25°C

4. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm. T

= 25°C

Thermal Characteristics

· Glass Passivated Die Construction

· Low Leakage Current

· High Forward Surge Current Capability

· Lead Free Finish, RoHS Compliant (Note 1)

· "Green" Molding Compound (No Br, Sb)

· Qualified to AEC-Q101 Standards for High Reliability

· Case: PowerDI

· Case Material: Molded Plastic, “Green” Molding

Compound. UL Flammability Classification Rating 94V-0

· Moisture Sensitivity: Level 1 per J-STD-020C

· Terminals: Finish – Matte Tin annealed over Copper

leadframe. Solderable per MIL-STD-202, Method 208

· Polarity: See Diagram

· Marking: See Page 3

· Weight: 0.095 grams (approximate)

Summary of content (3 pages)

PAGE 1
PDR3G 3A GLASS PASSIVATED RECTIFIER PowerDI ä5 Features · · · · · · Glass Passivated Die Construction A D Low Leakage Current A2 b2 High Forward Surge Current Capability L1 PowerDIä5 Lead Free Finish, RoHS Compliant (Note 1) E "Green" Molding Compound (No Br, Sb) E1 Qualified to AEC-Q101 Standards for High Reliability L1 e Mechanical Data · · Case: PowerDIä5 · · Moisture Sensitivity: Level 1 per J-STD-020C · · · D D2 b2 Case Material: Molded Plastic, “Green” Molding Compound.
PAGE 2
Electrical Characteristics @ TA = 25°C unless otherwise specified Symbol Min Typ Max Unit V(BR)R 400 ¾ ¾ V IR = 10mA VF ¾ 0.92 1.15 V IF = 3A, TS = 25°C Reverse Leakage Current (Note 5) IR ¾ ¾ 0.015 6 10 250 mA TS = 25°C, VR = 400V TS = 125°C, VR = 400V Reverse Recovery Time trr ¾ 3.0 ¾ ms IF = 0.5A, IR = 1.0A, Irr = 0.25A Characteristic Reverse Breakdown Voltage (Note 5) 5. Short duration test pulse used to minimize self-heating effect.
PAGE 3
180 TA, DERATED AMBIENT TEMPERATURE (°C) PF, FORWARD POWER DISSIPATION (W) 4 IPK = 1 (DC) IAV 3 2 1 150 120 90 60 30 0 0 0 1 3 2 0 5 4 IF, FORWARD CURRENT (A) Fig. 5 Forward Power Dissipation Ordering Information Notes: 100 400 300 200 VR, DC REVERSE VOLTAGE (V) Fig. 6 Operating Temperature Derating (Note 6) Device Packaging Shipping PDR3G-13 PowerDIä5 5000/Tape & Reel 6. For Packaging Details, go to our website at http://www.diodes.com/datasheets/ap02007.pdf.