DingTec® Laminators BU-360 to BU-2040 BU-380II to BU-2040II User’s Manual Version 1.0 Eastsign International Ltd Rm 1406, 14/F., Shatin Galleria 18-24 Shan Mei Street, Fotan, Shatin, N.T. Hong Kong http://www.eastsign.
User’s Manual of DingTec® Laminators – BU-380 to 2040 Cold Laminator Series PREFACE DingTec® BU-360 to 2040 series laminators are low-cost, cold laminators with either manual or automatic operating mode. They are easy to use and install. Users must read this manual thoroughly in order to maximize the capacity of the laminators and avoid damage. I.
User’s Manual of DingTec® Laminators – BU-380 to 2040 Cold Laminator Series II. Manual Cold Laminator Figure 1 A BU-380 to 2040 series manual cold laminator consists of following parts: 1. The upper and lower rubber rollers 2. The front and back working platforms 3. The left and right supports 4. The knob of adjustment 5. The handle (controlling the rollers) 6. Pressing roller (equipped with BU-1600 models and above) 7.
User’s Manual of DingTec® Laminators – BU-380 to 2040 Cold Laminator Series Figure 2 3. Turn the handle and let the film go without picture. Check whether the film is flat. If there are bubbles, it means the pressure is too high, the user needs to raise the rollers to reduce the pressure, then turn the knobs until upper limit of idling or proper position. Figure 3 4. Turn the handle counter-clockwise let one side (about 5-10cm) of the film pressed by the rollers.
User’s Manual of DingTec® Laminators – BU-380 to 2040 Cold Laminator Series Press the picture under the rollers, align it and flattening and secure the picture with hands. If pressing roller is available, you can use it to pressing the picture on its head. If the picture is thin and long, you can use double-sided adhesive tape to stick the picture on the padding paper (as Figure 4 and 5). Another person should turn the handle clockwise and press the picture into the rollers gradually.
User’s Manual of DingTec® Laminators – BU-380 to 2040 Cold Laminator Series One person should put the film under the roller and let the folded padding paper show up, then secure the padding paper by hands (you can also put the pressing roller on the picture). Another person should turn the handle clockwise at the same time and laminate the film and the picture together. Make sure the film with upper rubber roller should be smooth and the rolled film should be lower than the rollers.
User’s Manual of DingTec® Laminators – BU-380 to 2040 Cold Laminator Series If you want to change the spinning direction of the rollers during the operation, you should stop the machine first, then restart to avoid the damages due to suddenly changing directions. When the operational switch is on the position of the stop, you can use the pedal to operate the machine.
User’s Manual of DingTec® Laminators – BU-380 to 2040 Cold Laminator Series Notes: 1. When the upper roller is lying over the lower roller by gravity, the knobs can be turned easily at the idling position. Idling position has upper and lower limits. While the knobs is at the idling position, by continuously turn it clockwise, you will reach the lower limit till it is hard to move further; you will reach the upper limit by counter clockwise turning it till it is hard to move further 2.
User’s Manual of DingTec® Laminators – BU-380 to 2040 Cold Laminator Series Guarantee Model Ex-work serial No. User Purchase Date Sales Agent Phone No. Notes 1. The guarantee should be filled in by the sales agent and kept by the user; alterations are prohibited. 2. The guarantee period is 1-year parts, free of charge, and will be charged with material cost hereafter. 3. No free part is available for damages caused by improper use. Eastsign International Ltd (seal) Rm 1406, 14/F.
