Owner manual

2
Table 1. Parts List
ITEM
NO.
PCS.
REQ’D
DESCRIPTION PART NO.
1 1 Hub H08003* (4)
2 1 Bracket w/studs – 1 disc H080309-001
2 1 Bracket w/studs – 2 disc H080309-002
2 1 Bracket w/studs – 3 disc H080309-003
2 1 Bracket w/studs – 4 disc H080309-004
2 1 Bracket w/studs – 5 disc H080309-005
2a 1 Bracket w/high tensile studs – 1 disc H080309-006
2a 1 Bracket w/high tensile studs – 2 disc H080309-007
2a 1 Bracket w/high tensile studs – 3 disc H080309-008
2a 1 Bracket w/high tensile studs – 4 disc H080309-009
2a 1 Bracket w/high tensile studs – 5 disc H080309-010
3 4 Stud – 1 disc G070213-001
3 4 Stud – 2 disc G070213-002
3 4 Stud – 3 disc G070213-003
3 4 Stud – 4 disc G070213-004
3 4 Stud – 5 disc G070213-005
3a 4 Stud – 1 disc high tensile G070219-001
3a 4 Stud – 2 disc high tensile G070219-002
3a 4 Stud – 3 disc high tensile G070219-003
3a 4 Stud – 4 disc high tensile G070219-004
3a 4 Stud – 5 disc high tensile G070219-005
4 Note (1) Rotating friction disc H080002-004
4a Note (1) Heavy duty rotating friction disc (Alt.) K080281-001
5 Note (2) Stationary disc K080282-002
6 1 Pressure plate K080072-001
7 4 Torque spring (25, 50, 75 lb-ft) G070011-001
7 4 Torque spring (35, 70, 105, 125 175 lb-ft) G070019-001
8 4 Torque spring washer W004004-001
9 4 Torque adjusting nut W003001-022
10 2 Manual release rod G070001-002
11 2 Manual release spring G060010-001
12 2 Manual release washer W004004-003
13 As Req’d Manual release shim W004004-004
14 2 Manual release stop screw G060029-001
15 2 Manual release lockwasher W004007-007
16 1 Magnet assembly, single phase – complete with coils K080126 (3)
16 1 Magnet assembly, three phase – complete with coils K080127 (3)
17 1 Magnet plate w/o coils, single phase K080152-001
17a 1 Magnet plate w/o coils, three phase K080101-001
18 4 Magnet coil – single phase K080083 (3)
18a 6 Magnet coil – three phase H080062 (3)
19 2 Insulating washer – single phase G080148-001
19a 2 Insulating washer – three phase G080016-001
20 2 Shading coil, single phase only G080022-001
21 4 Gap adjusting nut W003003-023
22 4 Gap adjusting nut W003001-020
23 1 Cover, standard K080287-002
24 2 Cover screw W001002-103
25 1 Conduit hole plug W008001-007
26 1 Nameplate K060473-001
32 2 Lockwasher, 1/4 W004008-006
35 2 Drive screw W001012-048
(1) Number of rotating discs is shown as second digit of Model No.
Example: 2-82050-28
(2) Number of stationary discs is one less than the number of rotating discs.
(3) Basic part number shown–specify model number, voltage, phase and frequency.
(4) Basic part number shown–specify shaft diameter.