User guide

Table 2. Parts List
* Number of rotating discs is shown in model number.
Example:6-72
025-38 has two rotating discs.
Also see Table 1 for number of friction discs.
** Number of stationary discs is one less than the number of rotating discs.
4740 WEST ELECTRIC AVENUE
MILWAUKEE, WI 53219
PHONE [phone] FAX [phone]
www. dingsbrakes.com
ITEM
NO.
PCS.
REQ’D
DESCRIPTION PART NUMBER
1 1
Hub and Shaft Assembly - Specify
both diameters and keyways
Consult Factory
2 1 Bracket L070203-***
3 2 Studs H070180-***
4 * Rotating Friction Disc H070103-007
5 ** Stationary Disc K070485-001
6 1 Pressure Plate Assembly K070045-001P
7 2 Torque Spring ( 10 lb-ft) G070011-001
7 2 Torque Spring ( 25 lb-ft) G070019-001
7 2 Torque spring ( 15, 35, 50, 75 lb-ft) G070012-001
8 2 Torque Spring Washer W004004-001
9 2 Torque Adjusting Nut W003001-022
10 2 Manual Release Rod G070472-001
11 2 Manual Release Spring G060010-001
12 2 Manual Release Washer W004004-003
13 As Req’d
Manual Release Shims - .006”
Thick
W0040004-004
14 2 Maual Release Stop Screw G060029-001
15 2 Manual Release Lockwasher W004007-007
16 2 Manual Release Knob G070471-001
17 2 Roll Pin, 3/32 x 9/16 Lg. W005003-039
18 1
Magnet Mounting Plate Assembly
For 3-Phase Magnets (Includes
items 19 through 22)
K070097-***P
18 1
Magnet Mounting Plate Assembly
For 1-Phase Magnets (Includes
items 19 through 22)
K070335-***P
19 2 Roll Pin, 5/32 x 1-1/8 Lg. W005003-109
20 2 Insulating Washers, 3-Phase Coils G070037-001
20 2 Insulating Washers, 1-Phase Coils G070029-001
21 2 Coils- Single Phase H070013-***
21 2 Coils- Three Phase H020003-***
ITEM
NO.
PCS.
REQ’D
DESCRIPTION PART NUMBER
22 2 Shading Coil (Single phase only) G070032-001
23 2 Hex Jam Nut 1/2-20 W003003-023
24 2 ESNA Locknut 1/2-20 W003001-020
25 1 Adapter Housing (1-1/8 output shaft) L070202-003
25 1 Adapter Housing (1-3/8 output shaft) L070212-003
26 2 ESNA Locknut 1/2-20 W003001-020
27 1 Bearing-Double Seal (1-1/8 output shaft) W009001-002
28 1 Retaining Ring (1-1/8 output shaft) W006004-001
29 1 Retaining Ring (1-1/8 output shaft) W006002-002
30 1 Wrap Cover K070279-002
31 1 Nameplate with (2) Drive Screws N/A
32 1 Pipe Plug - 1/2 NPT W010002-004B
33 1 Pipe Plug - 1/8 NPT W010002-001B
34 1 “O” Ring W006001-010
35 2 Gasket for Brake Mounting K070250-004
36 2 Gasket W011004-001
37 2 RD. HD. Screw, #10-32 x 1” Lg. W001002-080C
38 2 Hex Nut #10-32 W003001-011C
39 1 Ball Bearing-Double Seal (1-3/8 output shaft) W009001-003
40 1 Retaining Ring (1-3/8 output shaft) W006002-003
41 2 Retaining Ring (1-3/8 output shaft) W006007-003
42 1 Plug Cap W008006-004
43 1 Plug Cap W008006-001
*** Part number is dependent on specific model number of brake.
For Magnet Assembly or Coils, part number is also dependent on voltage
rating. Contact Factory for part number.