SILVERTON SVT20 08/35674/0 Issue 3 The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
Table of Contents Welcome and Congratulations ..................................................... 2 Important Instructions ................................................................... 3 Site Selection and Preparation ..................................................... 4 Log Grate Assembly...................................................................... 6 Log Grate Installation ................................................................... 11 Operation .............................
Welcome and Congratulations Thank you and congratulations for choosing to purchase a Silverton from Dimplex. Please carefully read and save these instructions. Caution: Read all instructions and warnings carefully before starting installation.
Important Instructions Please read this information guide carefully to be able to safely install, use and maintain your product When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following: 1. WARNING This appliance carries a DO NOT COVER warning. Do not place material or garments on, or obstruct the air circulation around the appliance. 2.
CAUTION - Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present. This instruction can be found at WWW.DIMPLEX.CO.UK 8. USAGE Do not burn wood or other materials in the log grate Site Selections and Preparation This section provides instructions for selecting a location and preparing the site to install the Log Grate 1.
4. Unpack the transducer (contained within the water reservoir) which has been wrapped to protect it during shipping. See Figure 1. To access the transducer; • Remove the top cover by turning the retaining tabs on both ends of the water reservoir. • Remove any packaging material. • Install the transducer so that it is sitting level in the circular holding area in the resevoir.
Log Grate Assembly Caution: Handle logs carefully, they are fragile and can easily crack or break, if dropped.
Log Grate Assembly Each log is a separate component that needs to be placed on the grate. Position each log so that the hook and loop pad on the backside of the log lines up with the corresponding hook and loop pad on the log grate. These pads assist with securing the logs to the grate. Note: Each of these logs are hand made, and as such, the hook and loop pads on the logs and grate may not align perfectly, therefore, we have included additional pads should you need to reposition them.
Log Grate Assembly 8
Log Grate Assembly 9
Log Grate Assembly Caution: Ensure that the logs are placed so that they are not blocking the flame effect outlet 10
Log Grate Installation Only use filtered tap water in this appliance. Once installed, never move this appliance or lay it on its back, without draining the water from the sump and water tank. If you intend not using the appliance for longer that 2 weeks, drain the water from the reservoir and refill container. The refill container, reservoir, cover and container cap must be cleaned once every two weeks, particularly in hard water areas. 1) Fill and install the Refill Container.
Operation The manual controls for the Log Grate are located on the right side (Figure 3). A. On /Standby Switch. Supplies power to the Log Grate B. Momentary Button Pressing this button toggles between Logs, Logs and flame effect, and Off. Remote Control The unit is supplied with a radio frequency remote control. This remote control has a range of approximatly 15m. It does not have to be pointed at the fireplace and can pass through most obstacles (including walls).
Note: Once the mist has been activated, the unit will have to be turned Off, using either the momentary button, on the unit, on the Off button or the remote control, then back on to return to Level 1 - Logs and Lights only in operation. Battery Replacement To replace the battery, 1. Slide the battery cover open on the remote control (Figure 4) 2. Install one 12v (A23) battery in the battery holder 3.
on a biweekly basis. A small brush has been included to assist in cleaning difficult items/areas i.e. the transducer Caution: Do not put plastic components into the dishwasher. Note: If you need to move the unit ensure that all of the components that contain water have been emptied before relocating. Additional Information AFTER SALES SERVICE Your product is guaranteed for one year from the date of purchase.
PATENT / PATENT APPLICATION Products within the Optimyst range are protected by one or more of the following patents and patent applications: Great Britain GB 2402206, GB 2460259, GB 2460453 , GB 2418014, GB 2465738, GB 2449925, GB 2465537 , GB 2455277 , GB1020534.2, GB1020537.5, GB1110987.3 United States US 7967690, US 2010299980, US 2011062250, US 2008028648, US 13/167,042 Russia RU2008140317 European EP 2029941, EP 2201301, EP 2315976, EP 1787063, EP07723217.1 , EP11170434.2, EP 11170435.
OPTIMYST is a trade mark of GDC Group Ltd. GDC Group Ltd. MILLBROOK HOUSE GRANGE DRIVE HEDGE END SOUTHAMPTON TEL: 0844 879 3589 FAX: 0844 879 3583 WEBSITE: www.dimplex.co.uk Republic of Ireland Tel. 01 8424833 SO30 2DF c GDC Group Ltd, All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex. A division of GDC Group Ltd.
