OPTIMYST WALL ENGINE OMWFC20 08/51851/0 Issue 2 The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
Fig.1 Fig.2 Fig.4 Fig.3 Fig.
Fig.6 Fig.5 Fig.6a Fig.8 Fig.7 Fig.
Fig.10 Fig.11 Fig.
Dimplex Opti-myst wall Fire Model: OMWFC20 IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Important Safety Advice: When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following: If the appliance is damaged, check with the supplier before installation and operation. Do not use outdoors.
2. Fix the wall bracket to the wall making sure it is level, using the wall plugs and screws supplied for block walls. 3. Hang the appliance off the fixed wall bracket. Rotate the safety fixing bracket on the base of the product so that the fixing hole is exposed. Mark this hole and remove the appliance from the wall. Fix plug to the wall in the marked position. 4. Hang the appliance back on the wall fixing bracket and fix the appliance in place using the screw supplied through the safety fixing bracket.
2. View the lamps from a distance in front of the fire and observe which lamp needs to be changed. 3. Press switch ‘A’ to off (0) position (See Fig.2), and unplug the fire from the mains. 4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them. 5. Remove the water tank by lifting upwards and place in a sink. 6. Remove the sump as described in the Cleaning Section. 7.
Remote Control Operation On the control panel, Switch A (see Fig.2) must be in the ‘ON’ ( I ) position in order for the remote control to operate. There are 3 buttons on the remote control. (See Fig.7) To operate correctly the remote handset must be pointed towards the heater outlet. (See Fig 12). The remote control functions are as follows: Press once to turn on Flame effect only. This will be indicated by one beep. Press once to turn on Half heat and Flame effect. This will be indicated by two beeps.
Troubleshooting Symptom Cause Corrective Action The flame effect will not start. Mains plug is not plugged in. Check plug is connected to wall socket correctly. Low water level. Check that the water tank is full and there is water in the sump. Low voltage connector not connected properly. Check that the connector is inserted correctly. (See Fig.6) (See Fig.6) The flame effect is too low.
GLEN DIMPLEX PRODUCT WARRANTY This warranty is provided by Glen Dimplex Australia Pty Limited ABN 69 118 275 460 of Unit 1, 21 Lionel Road, Mount Waverley, Victoria 3149 (Phone number 1300 556 816), or in New Zealand by Glen Dimplex Australasia Limited, New Zealand registration number 1506305, of 38 Harris Road, East Tamaki, Auckland, New Zealand (Phone number 09 2748265) (we, us our) in respect of the Glen Dimplex product which this warranty card has been included in the packaging for or otherwise supplied
(c) the repair relates to the replacement of consumable parts such as fuses in plugs and bulbs or any other parts of the Glen Dimplex product which require routine replacement; (d) you are unable to provide us with reasonable proof of purchase for the Glen Dimplex product; (e) the breakdown occurs after the expiry of the express warranty period set out in section 1; or (f) the Glen Dimplex product was not purchased in Australia or New Zealand as a brand new product.
Glen Dimplex products are designed and supplied for normal domestic use. We will not be liable to you under this warranty for business loss or damage of any kind whatsoever. 6 Costs of warranty claim Where you make a claim under this warranty, a Glen Dimplex authorised repairer may need to attend your premises to inspect the Glen Dimplex product.
