Owner's Manual Model PF2325 PF3033 690932XXXX IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to install or use this fireplace. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage. To view the full line of Dimplex products, please visit www.dimplex.
Table of Contents Welcome & Congratulations . . . . . . . . . . . . . . . . . . 3 IMPORTANT INSTRUCTIONS. . . . . . . . . . . . . . . . . 4 Fireplace Installation . . . . . . . . . . . . . . . . . . . . . . . . 6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . .
Welcome & Congratulations Thank you and congratulations for purchasing an electric fireplace from Dimplex. Please use our convenient online registration page to record your model and serial numbers for future reference at www.dimplex.com/register Model and Serial Number Label Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation.
IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: ① Read all instructions before using this appliance. ② The heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation.
IMPORTANT INSTRUCTIONS ⑮ Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/ power strip). ⑯ Do not burn wood or other materials in the electric fireplace. ⑰ Do not strike the fireplace glass. ⑱ Always use a certified electrician should new circuits or outlets be required. ⑲ Always use properly grounded, fused and polarized outlets. ⑳ Disconnect all power supply before performing any cleaning, maintenance or relocation of the unit.
Fireplace Installation WARNING: Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury to persons. WARNING: Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons.
Fireplace Installation circulation beneath the fireplace insert is provided by 4 felt feet. Do not install the fireplace insert directly on carpet or similar surfaces which may restrict air circulation. CAUTION: If installing the fireplace in a carpeted area, place a one-piece, solid, flat surface under the fireplace. Ensure that all feet rest securely on this surface. ! NOTE: The dimensions of the firebox are: Width 24.1in. PF2325 (612mm) 31.3in. PF3033 (796mm) Custom Mantel Construction 1.
Fireplace Installation Option #1 - The power cord can be lead from behind the trim and along the wall to an outlet near the fireplace. Option #2 - A new outlet can be installed inside the new frame construction. Plug the unit into a 15 Amp/120 Volt outlet. ! NOTE: A 15 Amp, 120 Volt circuit is required. A dedicated circuit is preferred but not essential in all cases.
Fireplace Installation Wiring Diagram L MAIN BOARD G POWER SUPPLY LOGSET JUNCTION BOARD OR THERMAL CUT OUT MEDIA LED LIGHT ASSEMBLY RELAY BOARD HEATER ASSEMBLY OR FLAME BED LED ASSEMBLY (RGB) TOP LIGHT ASSY TOP LIGHT ASSY GESTURE ASSY NTC FLICKER MOTOR OR FLAME LED LIGHT ASSEMBLY (1W) 9
Operation General Operation WARNING: This electric firebox must be properly installed before it is used. This firebox operates with Comfort$averTM technology, which automatically adjusts the fan speed and heater wattage to safely and precisely match the requirements of the room based on the thermostat setting. The heater operates such that once the room reaches the set point, the fan and heater will continuously run at a low level, to maintain the desired room temperature.
Operation Figure 4 ① gWaveTM Controls LED Pilot Light Gesture On/Off ③ ⑦ ⑥ ⑩ ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ or “waving” in-front of the gWaveTM. "Waving" up will turn the unit On and "Waving" down will turn the unit Off. • The unit will turn on with the same functions that it was set to when it was turned Off and the intake temperature will be indicated on the On Screen Display. ! NOTE: When any button is pressed the intake temperature will be displayed on the On Screen Display for 5 seconds. 2.
Operation the Floating Display™ until the heater is turned off or the flames are turned back on. 4. activated. → Adjusted by pressing the corresponding button on the remote when the heater is on. Temperature Down: Decreases the heat output. • Indicated by the icon being illuminated on the Floating Display™ and the speed of the fan will decrease proportionally. → Adjusted by repeatedly pressing the corresponding button on the remote.
Operation using the buttons on the remote the lighting of the unit can be adjusted to any shade of any colour. The initial setting is no light (R=0, B=0, G=0) and can be adjusted, while the display is flashing, by pressing the outlined buttons (below) to adjust the tones. • Red Tones: increase and the decrease. • Green Tones: increase and decrease. • Blue Tones: decrease. increase and ! NOTE: There are 25 different settings for each colour. 9.
Operation Resetting the Temperature Cutoff Switch Should the heater overheat, an automatic cut out will turn the fireplace off and it will not come back on without being reset. It can be reset by unplugging the unit and waiting 15 minutes before plugging the unit back in. Once power is restored the unit will start to reset itself. During this process you will hear repeated beeps and the display may turn on and off.
Maintenance WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. scratching, do not use abrasive cleaners or spray liquids on the glass surface. CAUTION: Allow adequate time for the element and body casing to cool before attempting to clean the unit. To remove fingerprints or other marks, the exterior finish can be cleaned with a damp cloth with a mild detergent.
Warranty Products to which this limited warranty applies period of 1 year from the date of the first purchase of such products. This limited warranty applies to the following models of your newly purchased Dimplex electric fireplace 690932XXXX and to newly purchased Dimplex fireplace surrounds and trims.
Warranty product or part without charge. If Dimplex is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Dimplex may, in lieu of repair or replacement, choose to refund the purchase price for such product or part. • Limited warranty service will be performed solely by dealers or service agents of Dimplex authorized to provide limited warranty services.
Replacement Parts Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000480100RP Heater Assembly (with cutout). . . . . . . . . . . . . . . . . . . . . . . . . . 2203650100RP Cord Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4100190400RP Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3001250100RP Main Control Board with Display . . . . . . . . . . . . . . . . . . . . . . . .
