Installation and Operation Manual

Figure 2
B
E
F
G
H
I
A - Setting/Temperature Display
B - Economy Setting Icon
C - Set Back Temperature Setting
D - Comfort Setting Icon
E - Synchronized Icon
F - Lock Icon
G - Decrease Button
H - Increase Button
I - Menu Button
A
C
D
B. Economy Setting
The Economy Setting can be used to change the Setpoint
Temperature for a variable period of time. By pressing the V
the Economy Setting will be enabled - signied by the icon
ashing. After the Set Back Temperature has been set, the
icon will become solid after three seconds and the Set Back
Temperature will be enabled.
To return back to the Comfort Setting press the V button and
the icon will disappear and the icon will appear.
C. Set Back Temperature Setting
The Set Back Temperature Setting is used during periods
when the Economy setting feature is active. This temperature
adjustment can be set by pressing the V followed by the
+ or -.
D. Comfort Setting
The Comfort Setting icon will be displayed when the heater
is in normal operation based on the Setpoint Temperature for
the room.
!
NOTE: Either the or icon will always be visible,
dependent on the setting being used.
E. Synchronized Icon
The LPC features CONNEX
®
, a wireless technology that works
with Dimplex single and multi-zone CONNEX
®
controllers
to provide simple whole home connectivity and comfort.
CONNEX
®
controllers are available to control one or multiple
LPC’s or PCH’s within a 50' (15 m) radius. In order for the
controller to have this function the LPC and the controller will
need to be synchronized. To do this:
Figure 1
A B C D
Min.
1.5" (3.8 cm)
Min.
1.5" (3.8 cm)
Min.
1.5" (3.8cm)
Min.
3" (7.6 cm)
Min.
3" (7.6 cm)
Min.
3" (7.6 cm)
Min.
6" (15.3 cm)
Min.
See Item 4 & 5
for Dimension
Maintenance
CAUTION: Before removing the front cover for cleaning,
make certain the power has been turned off at the circuit
breaker panel, to prevent electric shock.
CAUTION: To avoid burns, allow adequate time for the
element and body casing to cool before attempting to work
on the smart baseboard.
The LPC series contain no moving parts. Since the appliance
contains no moving parts, little maintenance is required
beyond vacuum cleaning. It is however essential that the
smart baseboard is not operated with an accumulation of dust
or dirt on the element, as this can cause a build up of heat
and eventual damage. For this reason the smart baseboard
must be inspected regularly, depending upon conditions and
at least at yearly intervals. Once cleaning is complete replace
the front cover and restore power.
!
NOTE: The user can perform cleaning ONLY. All other
servicing should be performed by qualied service personnel.
1. On the LPC heater press and hold the V button for 3
seconds, both the and icons will begin to ash.
2. Press the - , + and then V, on the LPC heater.
3. Within 10 seconds press any button once on the CONNEX
®
controller.
!
NOTE: There is a 3 second delay between pressing the last
button on the CONNEX
®
controller and the LPC heater.
!
NOTE: To desynchronize a LPC heater from the
synchronized CONNEX
®
controller, on the LPC heater:
1. Press and hold the V for 3 seconds.
2. Press the V, + and then -.
Nothing needs to be done to the CONNEX
®
controller.
Dimplex single and multi-zone CONNEX
®
controllers are sold
separately and are available for purchase from your authorized
Dimplex dealer.
To nd your local Dimplex dealer, visit www.dimplex.com.
F. Lock Icon
The Smart Baseboard has a Button Lock feature, to prevent
settings from accidentally being changed.
1. Press and hold the V for 3 seconds. Both the and
Icons will begin to ash.
2. To Enable: Within 5 seconds press +, then -, then +, then
-. The icon will now be visible.
To Disable: Within 5 seconds press -, then +, then -, then
+. The icon will not be visible.
!
NOTE: The LPC can be locked in either the Comfort or
Economy Setting. Ensure that the desired icons are present
when locking is complete.
3